Abstract: This paper discusses the design and analysis of a
hybrid PV-Fuel cell energy system destined to power a DC load. The
system is composed of a photovoltaic array, a fuel cell, an
electrolyzer and a hydrogen tank. HOMER software is used in this
study to calculate the optimum capacities of the power system
components that their combination allows an efficient use of solar
resource to cover the hourly load needs. The optimal system sizing
allows establishing the right balance between the daily electrical
energy produced by the power system and the daily electrical energy
consumed by the DC load using a 28 KW PV array, a 7.5 KW fuel
cell, a 40KW electrolyzer and a 270 Kg hydrogen tank. The variation
of powers involved into the DC bus of the hybrid PV-fuel cell system
has been computed and analyzed for each hour over one year: the
output powers of the PV array and the fuel cell, the input power of
the elctrolyzer system and the DC primary load. Equally, the annual
variation of stored hydrogen produced by the electrolyzer has been
assessed. The PV array contributes in the power system with 82%
whereas the fuel cell produces 18%. 38% of the total energy
consumption belongs to the DC primary load while the rest goes to
the electrolyzer.
Abstract: In this paper, thick walled Cylindrical tanks or tubes
made of functionally graded material under internal pressure and
temperature gradient are studied. Material parameters have been
considered as power functions. They play important role in the
elastoplastic behavior of these materials. To clarify their role,
different materials with different parameters have been used under
temperature gradient. Finally, their effect and loading effect have
been determined in first yield point. Also, the important role of
temperature gradient was also shown. At the end the study has been
results obtained from changes in the elastic modulus and yield stress.
Also special attention is also given to the effects of this internal
pressure and temperature gradient in the creation of tensile and
compressive stresses.
Abstract: Malathion (ML) is a well known pesticide commonly
used in many agricultural and non-agricultural processes. Its toxicity
has been attributed primarily to the accumulation of acetylcholine
(Ach) at nerve junctions, due to the inhibition of acetylcholinesterase
(AChE). The aim of the current research was to study the protective
effect of the melissa plant extract against reproductive impairment
induced by malathion in 32 male albino rats, and the biological
experiment was divided into four groups (8 in each) that given
malathion (27 mg/kg; 1/50 of the LD50 for an oral dose) and/or
Melissa officinalis (MO) extract (200mg/kg/day) by gavages
technique. The sperm counts, sperm motility, sperm morphology,
FSH, LH, and testosterone levels had been determined in testes
homogenate at the end of the experiment. It is worthy to report that,
rats treated with melissa extract did not show a significant difference
when compared with the control group, while rats given malathion
alone had significantly lower sperm count, sperm motility, and
significantly higher abnormal sperm numbers, than the untreated
control rats as well as having significantly lower serum FSH, LH, and
testosterone levels compared with the control group. Administrations
of melissa extract restore all mentioned histological parameters
towards the control group and the melissa extract had a strong
positive protective effect against malathion toxicity. Results the of
biological parameters were confirmed by the histological
examination of rat testes and indicated that, both control and melissa
groups showing normal seminiferous tubules, while malathion group
testicular tissues had necrosis, edema in the seminiferous tubules and
degeneration of spermatogonial cells lining the seminiferous tubules
with incomplete spermatogenesis. The use of melissa against
malathion improved the histological picture and showing normal
seminiferous tubules with complete spermatogenesis and almost there
was no histopathological changes could be noted.
Abstract: Plant preparations from thyme and garlic have been shown to be effective acaricides against the poultry red mite, Dermanyssus gallinae. In a layer house with a history of D. gallinae problem, mites were detected in the monitoring traps for the first time and number of them was counted. Then, some rows of layer house was sprayed twice using a concentration of 0.21 mg/cm2 thyme essential oil and 0.07 mg/cm2 garlic juice and a similar row was used as an untreated control group. Red mite traps made of cardboard were used to assess the mite density during days 1 and 7 after treatment and always removed after 24 h. the collected mites were counted and the efficacy against all mite stages (larvae, nymphs and adults) was calculated. Results showed that on day 1 and 7 after the administration of garlic extract efficacy rate was 92.05% and 74.62%, respectively. Moreover, efficacy rate on day 1 and 7 was 89.4% and 95.37% when treatment was done with thyme essential oil. It is concluded that using garlic juice to control of D. gallinae is more effective on short time. But thyme essential oil has a long time effect in compare to garlic preparation.
Abstract: Three legumes i.e. soybean, kidney bean and mung
bean, and jojoba seed as an oil seed were processed into tempeh, a
fermented food. Changes in phytic acid, total phenols and trypsin
inhibitor were monitored during the pretreatments (soaking, soaking–
dehulling, washing and cooking) and fermentation with Rhizopus
oligosporus. Soaking was found to reduce total phenol and trypsin
inhibitor levels in soybean, kidney bean and mung bean. However,
phytic acid was reduced by soaking in kidney bean and mung bean.
Cooking was the most effective in reducing the activity of trypsin
inhibitor. During fermentation, a slight increase in the level of trypsin
inhibitor was noticed in soybean. Phytic acid and total phenols were
decreased during fermentation in soybean, kidney bean but mung
bean faild to form tempeh because the antifungal activity of herein a
protein in mung bean, which exerts both chitinase activity and
antifungal activity against a variety of fungal species. On the other
hand, solid- state fermentation of jojoba seeds was not effective in
reducing their content from cyanogenic glycosides (simmondsin).
Abstract: Death within 30 days is an important factor to be looked into, as there is a significant risk of deaths immediately following or soon after, myocardial infarction (MI) or stroke. In this paper, we will model the deaths within 30 days following a myocardial infarction (MI) or stroke in the UK. We will see how the probabilities of sudden deaths from MI or stroke have changed over the period 1981-2000. We will model the sudden deaths using a generalized linear model (GLM), fitted using the R statistical package, under a Binomial distribution for the number of sudden deaths. We parameterize our model using the extensive and detailed data from the Framingham Heart Study, adjusted to match UK rates. The results show that there is a reduction for the sudden deaths following a MI over time but no significant improvement for sudden deaths following a stroke.
Abstract: Exposure to ambient air pollution has been linked to a
number of health outcomes, starting from modest transient changes in
the respiratory tract and impaired pulmonary function, continuing to
restrict activity/reduce performance and to the increase emergency
rooms visits, hospital admissions or mortality. The increase of
allergenic symptoms has been associated with air contaminants such
as ozone, particulate matter, fungal spores and pollen.
Considering the potential relevance of crossed effects of nonbiological
pollutants and airborne pollens and fungal spores on
allergy worsening, the aim of this work was to evaluate the influence
of non-biological pollutants (O3 and PM10) and meteorological
parameters on the concentrations of pollen and fungal spores using
multiple linear regressions.
The data considered in this study were collected in Oporto which
is the second largest Portuguese city, located in the North. Daily
mean of O3, PM10, pollen and fungal spore concentrations,
temperature, relative humidity, precipitation, wind velocity, pollen
and fungal spore concentrations, for 2003, 2004 and 2005 were
considered. Results showed that the 90th percentile of the adjusted
coefficient of determination, P90 (R2aj), of the multiple regressions
varied from 0.613 to 0.916 for pollen and from 0.275 to 0.512 for
fungal spores. O3 and PM10 showed to have some influence on the
biological pollutants. Among the meteorological parameters
analysed, temperature was the one that most influenced the pollen
and fungal spores airborne concentrations. Relative humidity also
showed to have some influence on the fungal spore dispersion.
Nevertheless, the models for each pollen and fungal spore were
different depending on the analysed period, which means that the
correlations identified as statistically significant can not be, even so,
consistent enough.
Abstract: Lighvan cheese is basically made from sheep milk in
the area of Sahand mountainside which is located in the North West
of Iran. The main objective of this study was to investigate the effect
of enterococci isolated from traditional Lighvan cheese on the quality
of Iranian UF white during ripening. The experimental design was
split plot based on randomized complete blocks, main plots were four
types of starters and subplots were different ripening durations.
Addition of Enterococcus spp. did not significantly (P
Abstract: A nonlinear model of two-beam free-electron laser
(FEL) in the absence of slippage is presented. The two beams are
assumed to be cold with different energies and the fundamental
resonance of the higher energy beam is at the third harmonic of lower
energy beam. By using Maxwell-s equations and full Lorentz force
equations of motion for the electron beams, coupled differential
equations are derived and solved numerically by the fourth order
Runge–Kutta method. In this method a considerable growth of third
harmonic electromagnetic field in the XUV and X-ray regions is
predicted.
Abstract: The main objective of this study was to determine the effects
of vermicompost and amino acids on the qualitative and quantitative yield of
chamomile. The experiment was conducted during the growing season of
2010 at the Alborz Medical Research Center. The Treatment groups consisted
of vermicompost (0, 5, 10, 15 and 20 tons/ha) and the sprays of amino acids
(budding stag, flowering stage, and budding + flowering stage). The
experimental design was a factorial experiment based on Randomized
Complete Block Design (RCBD) with three replications. The present results
have shown that the highest plant height, flower head diameter, fresh and dry
flower yield and significant essential oil content were obtained by using 20-
ton vermicompost per hectare. Effects of amino acids were similar to those
seen in vermicompost treatment and all measured traits were seen to be
significant after the spray of amino acids at the budding + flowering stage).
Abstract: Improving performance measures in the construction
processes has been a major concern for managers and decision
makers in the industry. They seek for ways to recognize the key
factors which have the largest effect on the process. Identifying such
factors can guide them to focus on the right parts of the process in
order to gain the best possible result. In the present study design of
experiment (DOE) has been applied to a computer simulation model
of brick laying process to determine significant factors while
productivity has been chosen as the response of the experiment. To
this end, four controllable factors and their interaction have been
experimented and the best factor level has been calculated for each
one. The results indicate that three factors, namely, labor of brick,
labor of mortar and inter arrival time of mortar along with interaction
of labor of brick and labor of mortar are significant.
Abstract: In this paper a sliding-mode torque and flux control is
designed for encoderless synchronous reluctance motor drive. The
sliding-mode plus PI controllers are designed in the stator-flux field
oriented reference frame which is able to track the mentioned
reference signals with a minimum pulsations in the state condition. In
addition, with these controllers a fast dynamic response is also
achieved for the drive system. The proposed control scheme is robust
subject to parameters variation except to stator resistance. To solve
this problem a simple estimator is used for on-line detecting of this
parameter. Moreover, the rotor position and speed are estimated by
on-line obtaining of the stator-flux-space vector. The effectiveness
and capability of the proposed control approach is verified by both
the simulation and experimental results.
Abstract: In this paper, the absorption and fluorescence
emission spectra of Yb:Y3Al5O12 (YAG)(25 at%) crystal as a disk
laser medium are measured at high temperature (300-450K). The
absorption and emission cross sections of Yb:YAG crystal are
determined using Reciprocity method. Temperature dependence of
941nm absorption cross section and 1031nm emission cross section
is extracted in the range of 300-450K. According to our experimental
results, an exponential temperature dependence between 300K and
450K is acquired for the 1031nm peak emission cross section and
also for 941nm peak absorption cross section of Yb:YAG crystal.
These results could be used for simulation and design of high power
highly doped Yb:YAG thin disk lasers.
Abstract: In this article, biomechanical aspects of hen-s eggshell as a natural ceramic structure are studied. The images, taken by a scanning electron microscope (SEM), are used to investigate the microscopic aspects of the egg. It is observed that eggshell has a three-layered microstructure with different morphological and structural characteristics. Studies on the eggshell membrane (ESM) as a prosperous tissue suggest that it is placed to prevent the penetration of microorganisms into the egg. Finally, numerical models of the egg are presented to study the stress distribution and its deformation under different loading conditions. The effects of two different types of loading (hydrostatic and point loadings) on two different shell models (with constant and variable thicknesses) are investigated in detail.
Abstract: The Iranian bentonite was first characterized by
Scanning Electron Microscopy (SEM), Inductively Coupled Plasma
mass spectrometry (ICP-MS), X-ray fluorescence (XRF), X-ray
Diffraction (XRD) and BET. The bentonite was then treated
thermally between 150°C-250°C at 15min, 45min and 90min and
also was activated chemically with different concentration of
sulphuric acid (3N, 5N and 10N). Although the results of thermal
activated-bentonite didn-t show any considerable changes in specific
surface area and Cation Exchange Capacity (CEC), but the results of
chemical treated bentonite demonstrated that such properties have
been improved by acid activation process.
Abstract: A biosensor based on glucose oxidase (GOx) immobilized onto nanoparticles zirconium oxide with polyethylene nanocomposite for glucose monitoring has been designed. The CTAB/PEG/ZrO2/GOx nanocomposite was deposited onto screen printed carbon paste (SPCE) electrode via spin coating technique. The properties of CTAB/PEG/ZrO2/GOx were study using scanning electron microscopy (SEM). The SPE modified with the CTAB/PEG/ZrO2/GOx showed electrocatalytical response to the oxidation of glucose when ferrocene carboxaldehyde was used as an artificial redox mediator, which was studied by cyclic voltammetry (CV). Several parameters such as working potential, effect of pH and effect of ZrO2/PEG layers that governed the analytical performance of the biosensor, have been studied. The biosensor was applied to detect glucose with a linear range of 0.4 to 2.0 mmol L−1 with good repetability and reproducibility.
Abstract: One of the robust fault detection filter (RFDF)
designing method is based on sliding-mode theory. The main purpose
of our study is to introduce an innovative simplified reference
residual model generator to formulate the RFDF as a sliding-mode
observer without any manipulation package or transformation matrix,
through which the generated residual signals can be evaluated. So the
proposed design is more explicit and requires less design parameters
in comparison with approaches requiring changing coordinates. To
the best author's knowledge, this is the first time that the sliding
mode technique is applied to detect actuator and sensor faults in a
real boiler. The designing procedure is proposed in a drum boiler in
Synvendska Kraft AB Plant in Malmo, Sweden as a multivariable
and strongly coupled system. It is demonstrated that both sensor and
actuator faults can robustly be detected. Also sensor faults can be
diagnosed and isolated through this method.
Abstract: In this research, natural canthaxanthin as one of the
most important carotenoids was extracted from Dietzia
natronolimnaea HS-1. The changes of canthaxanthin enriched in oilin-
water emulsions with vegetable oil (5 mg/ 100 mL), Arabic gum (5
mg/100 mL), and potassium sorbate (0.5 g/100 mL) was investigated.
The effects of different pH (3, 5 and 7), as well as, time treatment (3,
18 and 33 days) in the environmental temperature (24°C) on the
degradation were studied by response surface methodology (RSM).
The Hunter values (L*, a*, and b*) and the concentration of
canthaxanthin (C, mg/L) illustrated more degradation of this pigment
at low pHs (pH≤ 4) by passing the time (days≥10) with R² 97.00%,
91.31%, 97.60%, and 99.54% for C, L*, a*, and b* respectively. The
predicted model were found to be significant (p
Abstract: Without uncertainty by applying external loads on
beams, bending is created. The created bending in I-beams, puts one
of the flanges in tension and the other one in compression. With increasing of bending, compression flange buckled and beam in out
of its plane direction twisted, this twisting well-known as Lateral Torsional Buckling. Providing bending moment varieties along the
beam, the critical moment is greater than the case its under pure bending. In other words, the value of bending gradient coefficient is
always greater than unite. In this article by the use of " ANSYS 10.0" software near 80 3-D finite element models developed for the
propose of analyzing beams` lateral torsional buckling and surveying influence of slenderness on beams' bending gradient coefficient.
Results show that, presented Cb coefficient via AISC is not correct for some of beams and value of this coefficient is smaller than what proposed by AISC. Therefore instead of using a constant Cb for each
case of loading , a function with two criterion for calculation of Cb coefficient for some cases is proposed.
Abstract: Virtual engineering technology has undergone rapid progress in recent years and is being adopted increasingly by manufacturing companies of many engineering disciplines. There is an increasing demand from industry for qualified virtual engineers. The qualified virtual engineers should have the ability of applying engineering principles and mechanical design methods within the commercial software package environment. It is a challenge to the engineering education in universities which traditionally tends to lack the integration of knowledge and skills required for solving real world problems. In this paper, a case study shows some recent development of a MSc Mechanical Engineering course at Department of Engineering and Technology in MMU, and in particular, two units Simulation of Mechanical Systems(SMS) and Computer Aided Fatigue Analysis(CAFA) that emphasize virtual engineering education and promote integration of knowledge acquisition, skill training and industrial application.