Abstract: A Space Vector based Pulse Width Modulation
control technique for the three-phase PWM converter is proposed in
this paper. The proposed control scheme is based on a synchronous
reference frame model. High performance and efficiency is obtained
with regards to the DC bus voltage and the power factor
considerations of the PWM rectifier thus leading to low losses.
MATLAB/SIMULINK are used as a platform for the simulations and
a SIMULINK model is presented in the paper. The results show that
the proposed model demonstrates better performance and properties
compared to the traditional SPWM method and the method improves
the dynamic performance of the closed loop drastically.
For the Space Vector based Pulse Width Modulation, Sine signal
is the reference waveform and triangle waveform is the carrier
waveform. When the value sine signal is large than triangle signal,
the pulse will start produce to high. And then when the triangular
signals higher than sine signal, the pulse will come to low. SPWM
output will changed by changing the value of the modulation index
and frequency used in this system to produce more pulse width. The
more pulse width produced, the output voltage will have lower
harmonics contents and the resolution increase.
Abstract: Contact stress is an important problem in industry.
This is a problem that in the first attention may be don-t appears, but
disregard of these stresses cause a lot of damages in machines. These
stresses occur at locations such as gear teeth, bearings, cams and
between a locomotive wheel and the railroad rail. These stresses
cause failure by excessive elastic deformation, yielding and fracture.
In this paper we intend show the effective parameters in contact
stress and ponder effect of curvature. In this paper we study contact
stresses on the surface of gear teeth and compare these stresses for
four popular profiles of gear teeth (involute, cycloid, epicycloids, and
hypocycloid). We study this problem with mathematical and finite
element methods and compare these two methods on different profile
surfaces.
Abstract: In modern day disaster recovery mission has become
one of the top priorities in any natural disaster management regime.
Smart autonomous robots may play a significant role in such
missions, including search for life under earth quake hit rubbles,
Tsunami hit islands, de-mining in war affected areas and many other
such situations. In this paper current state of many walking robots are
compared and advantages of hexapod systems against wheeled robots
are described. In our research we have selected a hexapod spider
robot; we are developing focusing mainly on efficient navigation
method in different terrain using apposite gait of locomotion, which
will make it faster and at the same time energy efficient to navigate
and negotiate difficult terrain. This paper describes the method of
terrain negotiation navigation in a hazardous field.
Abstract: The most important property of the Gene Ontology is
the terms. These control vocabularies are defined to provide
consistent descriptions of gene products that are shareable and
computationally accessible by humans, software agent, or other
machine-readable meta-data. Each term is associated with
information such as definition, synonyms, database references, amino
acid sequences, and relationships to other terms. This information has
made the Gene Ontology broadly applied in microarray and
proteomic analysis. However, the process of searching the terms is
still carried out using traditional approach which is based on keyword
matching. The weaknesses of this approach are: ignoring semantic
relationships between terms, and highly depending on a specialist to
find similar terms. Therefore, this study combines semantic similarity
measure and genetic algorithm to perform a better retrieval process
for searching semantically similar terms. The semantic similarity
measure is used to compute similitude strength between two terms.
Then, the genetic algorithm is employed to perform batch retrievals
and to handle the situation of the large search space of the Gene
Ontology graph. The computational results are presented to show the
effectiveness of the proposed algorithm.
Abstract: It is important to remove manganese from water
because of its effects on human and the environment. Human
activities are one of the biggest contributors for excessive manganese
concentration in the environment. The proposed method to remove
manganese in aqueous solution by using adsorption as in carbon
nanotubes (CNT) at different parameters: The parameters are CNT
dosage, pH, agitation speed and contact time. Different pHs are pH
6.0, pH 6.5, pH 7.0, pH 7.5 and pH 8.0, CNT dosages are 5mg,
6.25mg, 7.5mg, 8.75mg or 10mg, contact time are 10 min, 32.5 min,
55 min, 87.5 min and 120 min while the agitation speeds are 100rpm,
150rpm, 200rpm, 250rpm and 300rpm. The parameters chosen for
experiments are based on experimental design done by using Central
Composite Design, Design Expert 6.0 with 4 parameters, 5 levels and
2 replications. Based on the results, condition set at pH 7.0, agitation
speed of 300 rpm, 7.5mg and contact time 55 minutes gives the
highest removal with 75.5%. From ANOVA analysis in Design
Expert 6.0, the residual concentration will be very much affected by
pH and CNT dosage. Initial manganese concentration is 1.2mg/L
while the lowest residual concentration achieved is 0.294mg/L,
which almost satisfy DOE Malaysia Standard B requirement.
Therefore, further experiments must be done to remove manganese
from model water to the required standard (0.2 mg/L) with the initial
concentration set to 0.294 mg/L.
Abstract: The Indian subcontinent is facing a massive challenge with regards to the energy security in member countries, i.e. providing a reliable source of electricity to facilitate development across various sectors of the economy and thereby achieve the developmental targets it has set for itself. A highly precarious situation exists in the subcontinent which is observed in the series of system failures which most of the times leads to system collapses-blackouts. To mitigate the issues related with energy security as well as keep in check the increasing supply demand gap, a possible solution that stands in front of the subcontinent is the deployment of an interconnected electricity ‘Supergrid’ designed to carry huge quanta of power across the sub continent as well as provide the infra structure for RES integration. This paper assesses the need and conditions for a Supergrid deployment and consequently proposes a meshed topology based on VSC HVDC converters for the Supergrid modeling.
Abstract: Hydrocyclones flow field study is conducted by performing a parametric study. Effect of cone angle on deoiling hydrocyclones flow behaviour is studied in this research. Flow field of hydrocyclone is obtained by three-dimensional simulations with OpenFOAM code. Because of anisotropic behaviour of flow inside hydrocyclones LES is a suitable method to predict the flow field since it resolves large scales and model isotropic small scales. Large eddy simulation is used to predict the flow behavior of three different cone angles. Differences in tangential velocity and pressure distribution are reported in some figures.
Abstract: This paper investigates the performance of Multiple- Input Multiple-Output (MIMO) feedback system combined with Orthogonal Frequency Division Multiplexing (OFDM). Two types of codebook based channel feedback techniques are used in this work. The first feedback technique uses a combination of both the long-term and short-term channel state information (CSI) at the transmitter, whereas the second technique uses only the short term CSI. The long-term and short-term CSI at the transmitter is used for efficient channel utilization. OFDM is a powerful technique employed in communication systems suffering from frequency selectivity. Combined with multiple antennas at the transmitter and receiver, OFDM proves to be robust against delay spread. Moreover, it leads to significant data rates with improved bit error performance over links having only a single antenna at both the transmitter and receiver. The effectiveness of these techniques has been demonstrated through the simulation of a MIMO-OFDM feedback system. The results have been evaluated for 4x4 MIMO channels. Simulation results indicate the benefits of the MIMO-OFDM channel feedback system over the one without incorporating OFDM. Performance gain of about 3 dB is observed for MIMO-OFDM feedback system as compared to the one without employing OFDM. Hence MIMO-OFDM becomes an attractive approach for future high speed wireless communication systems.
Abstract: Increasing energy absorption is a significant parameter
in vehicle design. Absorbing more energy results in decreasing
occupant damage. Limitation of the deflection in a side impact results
in decreased energy absorption (SEA) and increased peak load (PL).
Hence a high crash force jeopardizes passenger safety and vehicle
integrity. The aims of this paper are to determine suitable dimensions
and material of a square beam subjected to side impact, in order to
maximize SEA and minimize PL. To achieve this novel goal, the
geometric parameters of a square beam are optimized using the
response surface method (RSM).multi-objective optimization is
performed, and the optimum design for different response features is
obtained.
Abstract: In this research a comparison between k-epsilon and
LES model for a deoiling hydrocyclone is conducted. Flow field of
hydrocyclone is obtained by three-dimensional simulations with
OpenFOAM code. Potential of prediction for both methods of this
complex swirl flow is discussed. Large eddy simulation method
results have more similarity to experiment and its results are
presented in figures from different hydrocyclone cross sections.
Abstract: Saudi Arabia in recent years has seen drastic increase
in traffic related crashes. With population of over 29 million, Saudi
Arabia is considered as a fast growing and emerging economy. The
rapid population increase and economic growth has resulted in rapid
expansion of transportation infrastructure, which has led to increase
in road crashes. Saudi Ministry of Interior reported more than 7,000
people killed and 68,000 injured in 2011 ranking Saudi Arabia to be
one of the worst worldwide in traffic safety. The traffic safety issues
in the country also result in distress to road users and cause and
economic loss exceeding 3.7 billion Euros annually. Keeping this in
view, the researchers in Saudi Arabia are investigating ways to
improve traffic safety conditions in the country. This paper presents a
multilevel approach to collect traffic safety related data required to do
traffic safety studies in the region. Two highway corridors including
King Fahd Highway 39 kilometre and Gulf Cooperation Council
Highway 42 kilometre long connecting the cities of Dammam and
Khobar were selected as a study area. Traffic data collected included
traffic counts, crash data, travel time data, and speed data. The
collected data was analysed using geographic information system to
evaluate any correlation. Further research is needed to investigate the
effectiveness of traffic safety related data when collected in a
concerted effort.
Abstract: Modular fixtures (MFs) are very important tools in
manufacturing processes in terms of reduction the cost and the
production time. This paper introduces an automated approach for
assembling MFs elements by employing SolidWorks as a powerful
3D CAD software. Visual Basic (VB) programming language was
applied integrating with SolidWorks API (Application programming
interface) functions. This integration allowed creating plug-in file and
generating new menus in the SolidWorks environment. The menus
allow the user to select, insert, and assemble MFs elements.
Abstract: The present study aims to explore the role of parents'
ethnic socialization practices contributes to the ethnic identity
development, self-esteem and psychological adjustment of multi
ethnic children in Sabah, Malaysia. A total of 342 multi ethnic
children (age range = 10 years old to 14 years old; mean age = 12.65
years, SD = 0.88) and their parents participated in the present study.
The modified version of Multi group Ethnic Identity Measure
(MEIM), The Familial Ethnic Socialization Measure (FESM). The
Rosenberg Self-Esteem Scale (RSE) and Behavioral and Emotional
Rating Scale Edition 2 (BERS-2) were used in this study. The results
showed that: i) parents' ethnic socialization practice was a strong
predictor of ethnic identity development of multi ethnic children; ii)
parents' ethnic socialization practice also was a significant predictor
of self-esteem of multi ethnic children; iii) parents' ethnic
socialization practice was not a significant predictor of psychological
adjustment of multi ethnic children. The results of this study showed
the implications parents' ethnic socialization practices and ethnic
identity development in successful multi ethnic families.
Abstract: An experimental study of anaerobic treatment was performed by hybrid upflow anaerobic sludge blanket (HUASB) reactor to treat produced water (PW) of an onshore crude oil terminal (COD: 1597 mg/L, NH3-N: 14.7 mg/L, phenol: 13.8 mg/L, BOD5: 862 mg/L, sodium: 6240 mg/L and chloride 9530 mg/L). The produced water with high salinity and other toxic substances will inhibit the methanogens performance if there is no adaptation on biomass before anaerobic digestion. COD removal from produced water was investigated at five different dilutions of produced water and tap water (TW) without any nutrient addition and pre-treatment. The dilution ratios were 1PW:4TW, 2PW:3TW, 3PW:2TW, 4PW:1TW and 5PW:0TW. The reactor was evaluated at mesophilic operating condition (35 ± 2 °C) at 5 days of HRT for 250 days continuous feed. The average COD removals for 1PW:4TW, 2PW:3TW, 3PW:2TW, 4PW:1TW and 5PW:0TW were found to be approximately 76.1%, 73.8%, 70.3%, 46.3% and 61.82% respectively, with final average effluent COD of 123.7 mg/L, 240 mg/L, 294 mg/L, 589 mg/L and 738 mg/L, respectively.
Abstract: In this research the separation efficiency of deoiling hydrocyclone is evaluated using three-dimensional simulation of multiphase flow based on Eulerian-Eulerian finite volume method. The mixture approach of Reynolds Stress Model is also employed to capture the features of turbulent multiphase swirling flow. The obtained separation efficiency of Colman's design is compared with available experimental data and showed that the separation curve of deoiling hydrocyclones can be predicted using numerical simulation.
Abstract: Variable ordering heuristics are used in constraint satisfaction algorithms. Different characteristics of various variable ordering heuristics are complementary. Therefore we have tried to get the advantages of all heuristics to improve search algorithms performance for solving constraint satisfaction problems. This paper considers combinations based on products and quotients, and then a newer form of combination based on weighted sums of ratings from a set of base heuristics, some of which result in definite improvements in performance.
Abstract: Hot tear cracking and residual stress are two different consequences of thermal stress both of which can be considered as casting problem. The purpose of the present study is simulation of the effect of casting shape characteristic on hot tearing and residual stress. This study shows that the temperature range for simulation of hot tearing and residual stress are different. In this study, in order to study the development of thermal stress and to predict the hot tearing and residual stress of shaped casting, MAGMASOFT simulation program was used. The strategy of this research was the prediction of hot tear location using pinpointing hot spot and thermal stress concentration zones. The results shows that existing of stress concentration zone increases the hot tearing probability and consequently reduces the amount of remaining residual stress in casting parts.
Abstract: Analytically the effect of polarization dependent loss on a high speed fiber optic communication link has been investigated. PDL and the signal's incoming state of polarization (SOP) have a significant co-relation between them and their various combinations produces different effects on the system behavior which has been inspected. Pauli's spin operator and PDL parameters are combined together to observe the attenuation effect induced by PDL in a link containing multiple PDL elements. It is found that in the presence of PDL the Q-factor and BER at the receiver undergoes fluctuation causing the system to be unstable and results show that it is mainly due to optical-signal-to-parallel-noise ratio (OSNItpar) that these parameters fluctuate. Generally the Q-factor, BER deteriorates as the value of average PDL in the link increases except for depolarized light for which the system parameters improves when PDL increases.
Abstract: In this paper we used data mining techniques to
identify outlier patients who are using large amount of drugs over a
long period of time. Any healthcare or health insurance system
should deal with the quantities of drugs utilized by chronic diseases
patients. In Kingdom of Bahrain, about 20% of health budget is spent
on medications. For the managers of healthcare systems, there is no
enough information about the ways of drug utilization by chronic
diseases patients, is there any misuse or is there outliers patients. In
this work, which has been done in cooperation with information
department in the Bahrain Defence Force hospital; we select the data
for Cardiac patients in the period starting from 1/1/2008 to
December 31/12/2008 to be the data for the model in this paper. We
used three techniques for finding the drug utilization for cardiac
patients. First we applied a clustering technique, followed by
measuring of clustering validity, and finally we applied a decision
tree as classification algorithm. The clustering results is divided into
three clusters according to the drug utilization, for 1603 patients, who
received 15,806 prescriptions during this period can be partitioned
into three groups, where 23 patients (2.59%) who received 1316
prescriptions (8.32%) are classified to be outliers. The classification
algorithm shows that the use of average drug utilization and the age,
and the gender of the patient can be considered to be the main
predictive factors in the induced model.
Abstract: Undoubtedly, chassis is one of the most important
parts of a vehicle. Chassis that today are produced for vehicles are
made up of four parts. These parts are jointed together by screwing.
Transverse parts are called cross member.
This study reviews the stress generated by cyclic laboratory loads
in front cross member of Peugeot 405. In this paper the finite element
method is used to simulate the welding process and to determine the
physical response of the spot-welded joints. Analysis is done by the
Abaqus software.
The Stresses generated in cross member structure are generally
classified into two groups: The stresses remained in form of residual
stresses after welding process and the mechanical stress generated by
cyclic load. Accordingly the total stress must be obtained by
determining residual stress and mechanical stress separately and then
sum them according to the superposition principle.
In order to improve accuracy, material properties including
physical, thermal and mechanical properties were supposed to be
temperature-dependent. Simulation shows that maximum Von Misses
stresses are located at special points. The model results are then
compared to the experimental results which are reported by
producing factory and good agreement is observed.