Abstract: The prologue of new High Voltage (HV) transmission
mains into the community necessitates earthing design to ensure
safety compliance of the system. Conductive structures such as steel
or concrete poles are widely used in HV transmission mains. The
earth potential rise (EPR) generated by a fault on these structures
could result to an unsafe condition. This paper discusses information
on the input impedance of the over head earth wire (OHEW) system
for finite and infinite transmission mains. The definition of finite and
infinite system is discussed, maximum EPR due to pole fault. The
simplified equations for EPR assessments are introduced and
discussed for the finite and infinite conditions. A case study is also
shown.
Abstract: Application of nanoparticles as additives in membrane
synthesis for improving the resistance of membranes against fouling
has triggered recent interest in new membrane types. However, most
nanoparticle-enhanced membranes suffer from the tradeoff between
permeability and selectivity. In this study, nano-WS2 was explored as
the additive in membrane synthesis by non-solvent induced phase
separation. Blended PES-WS2 flat-sheet membranes with the
incorporation of ultra-low concentrations of nanoparticles (from 0.025
to 0.25%, WS2/PES ratio) were manufactured and investigated in
terms of permeability, fouling resistance and solute rejection.
Remarkably, a significant enhancement in the permeability was
observed as a result of the incorporation of ultra-low fractions of
nano-WS2 to the membrane structure. Optimal permeability values
were obtained for modified membranes with 0.10%
nanoparticle/polymer concentration ratios. Furthermore, fouling
resistance and solute rejection were significantly improved by the
incorporation of nanoparticles into the membrane matrix. Specifically,
fouling resistance of modified membrane can increase by around 50%.
Abstract: This work evaluated the effect of temperature on headspace solid-phase microextraction of volatile and furanic compounds in coated fish sticks. The major goal was the analysis of the samples as consumed, to reproduce volatile compounds people feel when consuming those products. Extraction at 37 ºC (the human body temperature) throughout the HS-SPME analysis of volatile and furanic compounds in coated fish was compared with higher extraction temperatures, which are frequently used for this kind of determinations. The profile of volatile compounds found in deepfried (F) and non-fried (NF) coated fish at 37 and 50 ºC was different from that obtained at 80 ºC. Concerning furan and its derivatives, an extra formation of these compounds was observed at higher extraction temperatures. The analysis of volatile and furanic compounds in fish coated sticks simulating the cooking and eating conditions can be reliably carried out setting the headspace absorption temperature at 37 ºC.
Abstract: Four design alternatives for lateral force-resisting
systems of tall buildings in Dubai, UAE are presented. Quantitative
comparisons between the different designs are also made. This paper
is intended to provide different feasible lateral systems to be used in
Dubai in light of the available seismic hazard studies of the UAE.
The different lateral systems are chosen in conformance with the
International Building Code (IBC). Moreover, the expected behavior
of each system is highlighted and light is shed on some of the cost
implications associated with lateral system selection.
Abstract: The assessment of surface waters in Enugu metropolis
for fecal coliform bacteria was undertaken. Enugu urban was divided
into three areas (A1, A2 and A3), and fecal coliform bacteria
analysed in the surface waters found in these areas for four years
(2005-2008). The plate count method was used for the analyses. Data
generated were subjected to statistical tests involving; Normality test,
Homogeneity of variance test, correlation test, and tolerance limit
test. The influence of seasonality and pollution trends were
investigated using time series plots. Results from the tolerance limit
test at 95% coverage with 95% confidence, and with respect to EU
maximum permissible concentration show that the three areas suffer
from fecal coliform pollution. To this end, remediation procedure
involving the use of saw-dust extracts from three woods namely;
Chlorophora-Excelsa (C-Excelsa),Khayan-Senegalensis,(CSenegalensis)
and Erythrophylum-Ivorensis (E-Ivorensis) in
controlling the coliforms was studied. Results show that mixture of
the acetone extracts of the woods show the most effective
antibacterial inhibitory activities (26.00mm zone of inhibition)
against E-coli. Methanol extract mixture of the three woods gave best
inhibitory activity (26.00mm zone of inhibition) against S-areus, and
25.00mm zones of inhibition against E-Aerogenes. The aqueous
extracts mixture gave acceptable zones of inhibitions against the
three bacteria organisms.
Abstract: It is well known that Logistic Regression is the gold
standard method for predicting clinical outcome, especially
predicting risk of mortality. In this paper, the Decision Tree method
has been proposed to solve specific problems that commonly use
Logistic Regression as a solution. The Biochemistry and
Haematology Outcome Model (BHOM) dataset obtained from
Portsmouth NHS Hospital from 1 January to 31 December 2001 was
divided into four subsets. One subset of training data was used to
generate a model, and the model obtained was then applied to three
testing datasets. The performance of each model from both methods
was then compared using calibration (the χ2 test or chi-test) and
discrimination (area under ROC curve or c-index). The experiment
presented that both methods have reasonable results in the case of the
c-index. However, in some cases the calibration value (χ2) obtained
quite a high result. After conducting experiments and investigating
the advantages and disadvantages of each method, we can conclude
that Decision Trees can be seen as a worthy alternative to Logistic
Regression in the area of Data Mining.
Abstract: As new challenges emerge in power electrical
workplace safety, it is the responsibility of the systems designer to
seek out new approaches and solutions that address them. Design
decisions made today will impact cost, safety and serviceability of
the installed systems for 40 or 50 years during the useful life for the
owner. Studies have shown that this cost is an order of magnitude of
7 to 10 times the installed cost of the power distribution equipment.
This paper reviews some aspects of earthing system design in power
substation surrounded by residential houses. The electrical potential
rise and split factors are discussed and a few recommendations are
provided to achieve a safety voltage in the area beyond the boundary
of the substation.
Abstract: Researches show that probability-statistical methods application, especially at the early stage of the aviation Gas Turbine Engine (GTE) technical condition diagnosing, when the flight information has property of the fuzzy, limitation and uncertainty is unfounded. Hence the efficiency of application of new technology Soft Computing at these diagnosing stages with the using of the Fuzzy Logic and Neural Networks methods is considered. According to the purpose of this problem training with high accuracy of fuzzy multiple linear and non-linear models (fuzzy regression equations) which received on the statistical fuzzy data basis is made. For GTE technical condition more adequate model making dynamics of skewness and kurtosis coefficients- changes are analysed. Researches of skewness and kurtosis coefficients values- changes show that, distributions of GTE workand output parameters of the multiple linear and non-linear generalised models at presence of noise measured (the new recursive Least Squares Method (LSM)). The developed GTE condition monitoring system provides stage-by-stage estimation of engine technical conditions. As application of the given technique the estimation of the new operating aviation engine technical condition was made.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.
Abstract: Availability of high dimensional biological datasets such as from gene expression, proteomic, and metabolic experiments can be leveraged for the diagnosis and prognosis of diseases. Many classification methods in this area have been studied to predict disease states and separate between predefined classes such as patients with a special disease versus healthy controls. However, most of the existing research only focuses on a specific dataset. There is a lack of generic comparison between classifiers, which might provide a guideline for biologists or bioinformaticians to select the proper algorithm for new datasets. In this study, we compare the performance of popular classifiers, which are Support Vector Machine (SVM), Logistic Regression, k-Nearest Neighbor (k-NN), Naive Bayes, Decision Tree, and Random Forest based on mock datasets. We mimic common biological scenarios simulating various proportions of real discriminating biomarkers and different effect sizes thereof. The result shows that SVM performs quite stable and reaches a higher AUC compared to other methods. This may be explained due to the ability of SVM to minimize the probability of error. Moreover, Decision Tree with its good applicability for diagnosis and prognosis shows good performance in our experimental setup. Logistic Regression and Random Forest, however, strongly depend on the ratio of discriminators and perform better when having a higher number of discriminators.
Abstract: Continuation of an active call is one of the most important quality measurements in the cellular systems. Handoff process enables a cellular system to provide such a facility by transferring an active call from one cell to another. Different approaches are proposed and applied in order to achieve better handoff service. The principal parameters used to evaluate handoff techniques are: forced termination probability and call blocking probability. The mechanisms such as guard channels and queuing handoff calls decrease the forced termination probability while increasing the call blocking probability. In this paper we present an overview about the issues related to handoff initiation and decision and discuss about different types of handoff techniques available in the literature.
Abstract: Fourty one strains of ESBL producing P.aeruginosa
which were previously isolated from burn patients in Kerman
University general hospital, Iran were subjected to PCR, RFLP and
sequencing in order to determine the type of extended spectrum β-
lactamases (ESBL), the restriction digestion pattern and possibility of
mutation among detected genes. DNA extraction was carried out by
phenol chloroform method. PCR for detection of bla genes was
performed using specific primer for each gene. Restriction Fragment
Length Polymorphism (RFLP) for ESBL genes was carried out using
EcoRI, NheI, PVUII, EcoRV, DdeI, and PstI restriction enzymes. The
PCR products were subjected to direct sequencing of both the strands
for identification of the ESBL genes.The blaCTX-M, blaVEB-1, blaPER-1,
blaGES-1, blaOXA-1, blaOXA-4 and blaOXA-10 genes were detected in the
(n=1) 2.43%, (n=41)100%, (n=28) 68.3%, (n=10) 24.4%, (n=29)
70.7%, (n=7)17.1% and (n=38) 92.7% of the ESBL producing isolates
respectively. The RFLP analysis showed that each ESBL gene has
identical pattern of digestion among the isolated strains. Sequencing
of the ESBL genes confirmed the genuinety of PCR products and
revealed no mutation in the restriction sites of the above genes. From
results of the present investigation it can be concluded that blaVEB-1
and blaCTX-M were the most and the least frequently isolated ESBL
genes among the P.aeruginosa strains isolated from burn patients. The
RFLP and sequencing analysis revealed that same clone of the bla
genes were indeed existed among the antibiotic resistant strains.
Abstract: Dengue is a mosquito-borne infection that has peaked to an alarming rate in recent decades. It can be found in tropical and sub-tropical climate. In Malaysia, dengue has been declared as one of the national health threat to the public. This study aimed to map the spatial distributions of dengue cases in the district of Hulu Langat, Selangor via a combination of Geographic Information System (GIS) and spatial statistic tools. Data related to dengue was gathered from the various government health agencies. The location of dengue cases was geocoded using a handheld GPS Juno SB Trimble. A total of 197 dengue cases occurring in 2003 were used in this study. Those data then was aggregated into sub-district level and then converted into GIS format. The study also used population or demographic data as well as the boundary of Hulu Langat. To assess the spatial distribution of dengue cases three spatial statistics method (Moran-s I, average nearest neighborhood (ANN) and kernel density estimation) were applied together with spatial analysis in the GIS environment. Those three indices were used to analyze the spatial distribution and average distance of dengue incidence and to locate the hot spot of dengue cases. The results indicated that the dengue cases was clustered (p < 0.01) when analyze using Moran-s I with z scores 5.03. The results from ANN analysis showed that the average nearest neighbor ratio is less than 1 which is 0.518755 (p < 0.0001). From this result, we can expect the dengue cases pattern in Hulu Langat district is exhibiting a cluster pattern. The z-score for dengue incidence within the district is -13.0525 (p < 0.0001). It was also found that the significant spatial autocorrelation of dengue incidences occurs at an average distance of 380.81 meters (p < 0.0001). Several locations especially residential area also had been identified as the hot spots of dengue cases in the district.
Abstract: The Integrated Performance Modelling Environment
(IPME) is a powerful simulation engine for task simulation and
performance analysis. However, it has no high level cognition such
as memory and reasoning for complex simulation. This article
introduces a knowledge representation and reasoning scheme that can
accommodate uncertainty in simulations of military personnel with
IPME. This approach demonstrates how advanced reasoning models
that support similarity-based associative process, rule-based abstract
process, multiple reasoning methods and real-time interaction can be
integrated with conventional task network modelling to provide
greater functionality and flexibility when modelling operator
performance.
Abstract: The counting and analysis of blood cells allows the
evaluation and diagnosis of a vast number of diseases. In particular,
the analysis of white blood cells (WBCs) is a topic of great interest to
hematologists. Nowadays the morphological analysis of blood cells is
performed manually by skilled operators. This involves numerous
drawbacks, such as slowness of the analysis and a nonstandard
accuracy, dependent on the operator skills. In literature there are only
few examples of automated systems in order to analyze the white
blood cells, most of which only partial. This paper presents a
complete and fully automatic method for white blood cells
identification from microscopic images. The proposed method firstly
individuates white blood cells from which, subsequently, nucleus and
cytoplasm are extracted. The whole work has been developed using
MATLAB environment, in particular the Image Processing Toolbox.
Abstract: Biodiesel as an alternative fuel for diesel engines has been developed for some three decades now. While it is gaining wide acceptance in Europe, USA and some parts of Asia, the same cannot be said of Africa. With more than 35 countries in the continent depending on imported crude oil, it is necessary to look for alternative fuels which can be produced from resources available locally within any country. Hence this study presents performance of single cylinder diesel engine using blends of shea butter biodiesel. Shea butter was transformed into biodiesel by transesterification process. Tests are conducted to compare the biodiesel with baseline diesel fuel in terms of engine performance and exhaust emission characteristics. The results obtained showed that the addition of biodiesel to diesel fuel decreases the brake thermal efficiency (BTE) and increases the brake specific fuel consumption (BSFC). These results are expected due to the lower energy content of biodiesel fuel. On the other hand while the NOx emissions increased with increase in biodiesel content in the fuel blends, the emissions of carbon monoxide (CO), un-burnt hydrocarbon (UHC) and smoke opacity decreased. The engine performance which indicates that the biodiesel has properties and characteristics similar to diesel fuel and the reductions in exhaust emissions make shea butter biodiesel a viable additive or substitute to diesel fuel.
Abstract: Two short sediment cores collected from mangrove
areas of Manori and Thane creeks along Mumbai coast were analysed
for sediment composition and metals (Fe, Mn, Cu, Pb, Co, Ni, Zn, Cr
and V). The statistical analysis of Pearson correlation matrix proved
that there is a significant relationship between metal concentration
and finer grain size in Manori creek while poor correlation was
observed in Thane creek. Based on the enrichment factor, the present
metal to background metal ratios clearly reflected maximum
enrichment of Cu and Pb in Manori creek and Mn in Thane creek.
Geoaccumulation index calculated indicate that the study area is
unpolluted with respect to Fe, Mn, Co, Ni, Zn and Cr in both the
cores while moderately polluted with Cu and Pb in Manori creek.
Based on contamination degree, both the core sediments were found
to be considerably contaminated with metals.
Abstract: The financial crisis has decreased the opportunities of
small businesses to acquire financing through conventional financial
actors, such as commercial banks. This credit constraint is partly the
reason for the emergence of new alternatives of financing, in addition
to the spreading opportunities for communication and secure
financial transfer through Internet. One of the most interesting venues
for finance is termed “crowdfunding". As the term suggests
crowdfunding is an appeal to prospective customers and investors to
form a crowd that will finance projects that otherwise would find it
hard to generate support through the most common financial actors.
Crowdfunding is in this paper divided into different models; the
threshold model, the microfinance model, the micro loan model and
the equity model. All these models add to the financial possibilities of
emerging entrepreneurs.
Abstract: The purpose of this research was to investigate Thai Muslims’ way of life through the way their clothes. The data of this qualitative research were collected from related documents and research reports, ancient cloths and clothing, and in-depth interviews with clothes owners and weavers.
The research found that in the 18th century Thai Muslims in the three southern border provinces used many types of clothing in their life. At home women wore plain clothes. They used checked cloths to cover the upper part of their body from the breasts down to the waist. When going out, they used Lima cloth and So Kae with a piece of Pla-nging cloth as a head scarf. For men, they wore a checked sarong as a lower garment, and wore no upper garment. However, when going out, they wore Puyo Potong. In addition, Thai Muslims used cloths in various religious rites, namely, the rite of placing a baby in a cradle, the Masoyawi rite, the Nikah rite, and the burial rite. These types of cloths were related to the way of life of Thai Muslims from birth to death. They reflected the race, gender, age, social status, values, and beliefs in traditions that have been inherited.
Practical Implication: Woven in these cloths are the lost local wisdom, and therefore, aesthetics on the cloths are like mirrors reflecting the background of people in this region that is fading away. These cloths are pages of a local history book that is of importance and value worth for preservation and publicity so that they are treasured. Government organizations can expand and materialize the knowledge received from the study in accordance with government policy in supporting the One Tambon, One Product project.
Abstract: In today-s turbulent environment, companies are faced with two principal challenges. On the one hand, it is necessary to produce ever more cost-effectively to remain competitive. On the other hand, factories need to be transformable in order to manage unpredictable changes in the corporate environment. To deal with these different challenges, companies use the philosophy of lean production in the first case, in the second case the philosophy of transformability. To a certain extent these two approaches follow different directions. This can cause conflicts when designing factories. Therefore, the Institute of Production Systems and Logistics (IFA) of the Leibniz University of Hanover has developed a procedure to allow companies to evaluate and design their factories with respect to the requirements of both philosophies.