Abstract: Recognition of characters greatly depends upon the features used. Several features of the handwritten Arabic characters are selected and discussed. An off-line recognition system based on the selected features was built. The system was trained and tested with realistic samples of handwritten Arabic characters. Evaluation of the importance and accuracy of the selected features is made. The recognition based on the selected features give average accuracies of 88% and 70% for the numbers and letters, respectively. Further improvements are achieved by using feature weights based on insights gained from the accuracies of individual features.
Abstract: This paper presents an overview of the multiobjective shortest path problem (MSPP) and a review of essential and recent issues regarding the methods to its solution. The paper further explores a multiobjective evolutionary algorithm as applied to the MSPP and describes its behavior in terms of diversity of solutions, computational complexity, and optimality of solutions. Results show that the evolutionary algorithm can find diverse solutions to the MSPP in polynomial time (based on several network instances) and can be an alternative when other methods are trapped by the tractability problem.
Abstract: In this paper, a novel approach for robust trajectory tracking of induction motor drive is presented. By combining variable structure systems theory with fuzzy logic concept and neural network techniques, a new algorithm is developed. Fuzzy logic was used for the adaptation of the learning algorithm to improve the robustness of learning and operating of the neural network. The developed control algorithm is robust to parameter variations and external influences. It also assures precise trajectory tracking with the prescribed dynamics. The algorithm was verified by simulation and the results obtained demonstrate the effectiveness of the designed controller of induction motor drives which considered as highly non linear dynamic complex systems and variable characteristics over the operating conditions.
Abstract: Environmental responsibility includes improvement of environmental performance in order to reduce environmental impact. This paper gives a short review of some important environmental objectives, targets and actions that modern shipping company should follow.
Abstract: In this paper is to evaluate audio and speech quality
with the help of Digital Audio Watermarking Technique under the
different types of attacks (signal impairments) like Gaussian Noise,
Compression Error and Jittering Effect. Further attacks are
considered as Hostile Environment. Audio and Speech Quality
Evaluation is an important research topic. The traditional way for
speech quality evaluation is using subjective tests. They are reliable,
but very expensive, time consuming, and cannot be used in certain
applications such as online monitoring. Objective models, based on
human perception, were developed to predict the results of subjective
tests. The existing objective methods require either the original
speech or complicated computation model, which makes some
applications of quality evaluation impossible.
Abstract: We report here, the results of molecular dynamics
simulation of p-doped (Ga-face)GaN over n-doped (Siface)(
0001)4H-SiC hetero-epitaxial material system with one-layer
each of Ga-flux and (Al-face)AlN, as the interface materials, in the
form of, the total Density of States (DOS). It is found that the total
DOS at the Fermi-level for the heavily p-doped (Ga-face)GaN and ndoped
(Si-face)4H-SiC hetero-epitaxial system, with one layer of
(Al-face)AlN as the interface material, is comparatively higher than
that of the various cases studied, indicating that there could be good
vertical conduction across the (Ga-face)GaN over (Si-face)(0001)4HSiC
hetero-epitaxial material system.
Abstract: While computers are known to facilitate lower levels of learning, such as rote memorization of facts, measurable through electronically administered and graded multiple-choice questions, yes/no, and true/false answers, the imparting and measurement of higher-level cognitive skills is more vexing. These require more open-ended delivery and answers, and may be more problematic in an entirely virtual environment, notwithstanding the advances in technologies such as wikis, blogs, discussion boards, etc. As with the integration of all technology, merit is based more on the instructional design of the course than on the technology employed in, and of, itself. With this in mind, this study examined the perceptions of online students in an introductory Computer Information Systems course regarding the fostering of various higher-order thinking and team-building skills as a result of the activities, resources and technologies (ART) used in the course.
Abstract: Elastic and inelastic scattering of α-particles by 9Be nuclei at different incident energies have been analyzed. Optical model parameters (OMPs) of α-particles elastic scattering by 9Be at different energies have been obtained. Coupled Reaction Channel (CRC) of elastic scattering, inelastic scattering and transfer reaction has been calculated using Fresco Code. The effect of involving CRC calculations on the analysis of differential cross section has been studied. The transfer reaction of (5He) in the reaction 9Be(α,9Be)α has been studied. The spectroscopic factor of 9Be≡α+5He has been extracted.
Abstract: In this article, we propose a methodology for the
characterization of the suspended matter along Algiers-s bay. An
approach by multi layers perceptron (MLP) with training by back
propagation of the gradient optimized by the algorithm of Levenberg
Marquardt (LM) is used. The accent was put on the choice of the
components of the base of training where a comparative study made
for four methods: Random and three alternatives of classification by
K-Means. The samples are taken from suspended matter image,
obtained by analytical model based on polynomial regression by
taking account of in situ measurements. The mask which selects the
zone of interest (water in our case) was carried out by using a multi
spectral classification by ISODATA algorithm. To improve the
result of classification, a cleaning of this mask was carried out using
the tools of mathematical morphology. The results of this study
presented in the forms of curves, tables and of images show the
founded good of our methodology.
Abstract: In order to study the influence of different methods of controlling weeds such as mechanical weeding and mechanical weeder efficiency analysis in mechanical cultivation conditions, in farming year of 2011 an experiment was done in a farm in coupling and development of technology center in Haraz,Iran. The treatments consisted of (I) control treatment: where no weeding was done, (II) use of mechanical weeding without engine and (III) power mechanical weeding. Results showed that experimental treatments had significantly different effects (p=0.05) on yield traits and number of filled grains per panicle, while treatments had the significant effects on grain weight and dry weight of weeds in the first, second and third weeding methods at 1% of confidence level. Treatment (II) had its most significant effect on number of filled grains per panicle and yield performance standpoint, which was 3705.97 kg ha-1 in its highest peak. Treatment (III) was ranked as second influential with 3559.8 kg ha-1. In addition, under (I) treatments, 2364.73 kg ha-1 of yield produced. The minimum dry weights of weeds in all weeding methods were related to the treatment (II), (III) and (I), respectively. The correlation coefficient analysis showed that total yield had a significant positive correlation with the panicle grain yield per plant (r= 0.55*) and the number of grains per panicle-1 (r= 0.57*) and the number of filled grains (r= 0.63*). Total rice yield also had negative correlation of r= -0. 64* with weed dry weight at second weed sampling time (17 DAT). The weed dry weight at third and fourth sampling times (24 and 40 DAT) had negative correlations of -0.65** and r=-0.61* with rice yield, respectively.
Abstract: Unlike the best effort service provided by the internet
today, next-generation wireless networks will support real-time
applications. This paper proposes an adaptive early packet discard
(AEPD) policy to improve the performance of the real time TCP
traffic over ATM networks and avoid the fragmentation problem.
Three main aspects are incorporated in the proposed policy. First,
providing quality-of-service (QoS) guaranteed for real-time
applications by implementing a priority scheduling. Second,
resolving the partially corrupted packets problem by differentiating
the buffered cells of one packet from another. Third, adapting a
threshold dynamically using Fuzzy logic based on the traffic
behavior to maintain a high throughput under a variety of load
conditions. The simulation is run for two priority classes of the input
traffic: real time and non-real time classes. Simulation results show
that the proposed AEPD policy improves throughput and fairness
over that using static threshold under the same traffic conditions.
Abstract: Cogeneration may be defined as a system which
contains electricity production and regain of the thermo value of
exhaust gases simultaneously. The examination is based on the data-s
of an active cogeneration plant. This study, it is aimed to determine
which component of the system should be revised first to raise the
efficiency and decrease the loss of exergy. For this purpose, second
law analysis of thermodynamics is applied to each component due to
consider the effects of environmental conditions and take the quality
of energy into consideration as well as the quantity of it. The exergy
balance equations are produced and exergy loss is calculated for each
component. 44,44 % loss of exergy in heat exchanger, 29,59 % in
combustion chamber, 18,68 % in steam boiler, 5,25 % in gas turbine
and 2,03 % in compressor is calculated.
Abstract: Gilaburu (Viburnum opulus L.) grown naturally in
Anatolia. In this study, some physico-chemical (sugar, acid, protein,
crude fat, crude fiber, ash etc.) characteristics and mineral
composition of Gilaburu fruit have been investigated. The length,
width, thickness, weight, total soluble solid, protein, crude ash, crude
fiber and crude oil of fruit were found to be 1.12 cm, 1.58 cm, 1.87
cm, 0.87 g, 14.73 %, 0.2 %, 0.11 %, 6.56 % and 0.4 %, respectively.
The seed of fruit mean weight, length, width and thickness were
determinated as 0.08 g, 7.76 cm, 7.67 cm and 1.66, respectively. In
addition 27 mineral elements (Al, Mg, Na, Ba, Ca, Ni, Cd, P, Cr, Pb,
S, Cu, Se, Fe, K, Sr, Li, Z, V, Ag, Bi, Co, Mn, B, Ga, In, Ti) were
analyzed. Gilaburu (Viburnum opulus L.) fruit was richest in
potassium (10764.764 ppm), Mg (1289.088 ppm) and P (1304.169
ppm).
Abstract: During the last few years, several sheet hydroforming
processes have been introduced. Despite the advantages of these
methods, they have some limitations. Of the processes, the two main
ones are the standard hydroforming and hydromechanical deep
drawing. A new sheet hydroforming die set was proposed that has the
advantages of both processes and eliminates their limitations. In this
method, a polyurethane plate was used as a part of the die-set to
control the blank holder force. This paper outlines the Taguchi
optimization methodology, which is applied to optimize the effective
parameters in forming cylindrical cups by the new die set of sheet
hydroforming process. The process parameters evaluated in this
research are polyurethane hardness, polyurethane thickness, forming
pressure path and polyurethane hole diameter. The design of
experiments based upon L9 orthogonal arrays by Taguchi was used
and analysis of variance (ANOVA) was employed to analyze the
effect of these parameters on the forming pressure. The analysis of
the results showed that the optimal combination for low forming
pressure is harder polyurethane, bigger diameter of polyurethane hole
and thinner polyurethane. Finally, the confirmation test was derived
based on the optimal combination of parameters and it was shown
that the Taguchi method is suitable to examine the optimization
process.
Abstract: A Cable-Driven Locomotion Interface provides a low
inertia haptic interface and is used as a way of enabling the user
to walk and interact with virtual surfaces. These surfaces generate
Cartesian wrenches which must be optimized for each motorized
reel in order to reproduce a haptic sensation in both feet. However,
the use of wrench control requires a measure of the cable tensions
applied to the moving platform. The latter measure may be inaccurate
if it is based on sensors located near the reel. Moreover, friction
hysteresis from the reel moving parts needs to be compensated
for with an evaluation of low angular velocity of the motor shaft.
Also, the pose of the platform is not known precisely due to cable
sagging and mechanical deformation. This paper presents a non-ideal
motorized reel design with its corresponding control strategy that
aims at overcoming the aforementioned issues. A transfert function
of the reel based on frequency responses in function of cable tension
and cable length is presented with an optimal adaptative PIDF
controller. Finally, an hybrid position/tension control is discussed with
an analysis of the stability for achieving a complete functionnality of
the haptic platform.
Abstract: Attempt was made to improve certain characteristics of bio-oil derived from palm kernel pyrolysis by blending it with diesel fuel and alcohols. Two types of alcohol, ethanol or butanol, was used as cosolvent to stabilize the phase of ternary systems. Phase behaviors and basic fuel properties of palm kernel bio-oildiesel- alcohol systems were investigated in this study. Alcohol types showed a significant influence on the phase characteristics with palm kernel bio-oil-diesel-butanol system giving larger soluble area than that of palm kernel bio-oil-diesel-ethanol system. For fuel properties, blended fuels showed superior properties including lower values of density (~860 kg/m3 at 25°C), viscosity (~4.12 mm2/s at 40°C), carbon residue (1.02-2.53 wt%), ash (0.018-0.034 wt%) and pour point (
Abstract: The purpose of this paper is to provide a practical
example to the Linear Quadratic Gaussian (LQG) controller. This
method includes a description and some discussion of the discrete
Kalman state estimator. One aspect of this optimality is that the
estimator incorporates all information that can be provided to it. It
processes all available measurements, regardless of their precision, to
estimate the current value of the variables of interest, with use of
knowledge of the system and measurement device dynamics, the
statistical description of the system noises, measurement errors, and
uncertainty in the dynamics models.
Since the time of its introduction, the Kalman filter has been the
subject of extensive research and application, particularly in the area
of autonomous or assisted navigation. For example, to determine the
velocity of an aircraft or sideslip angle, one could use a Doppler
radar, the velocity indications of an inertial navigation system, or the
relative wind information in the air data system. Rather than ignore
any of these outputs, a Kalman filter could be built to combine all of
this data and knowledge of the various systems- dynamics to
generate an overall best estimate of velocity and sideslip angle.
Abstract: Combining energy efficiency with renewable energy
sources constitutes a key strategy for a sustainable future. The wind
power sector stands out as a fundamental element for the
achievement of the European renewable objectives and Portugal is no
exception to the increase of the wind energy for the electricity
generation. This work proposes an optimization model for the long
range electricity power planning in a system similar to the
Portuguese one, where the expected impacts of the increasing
installed wind power on the operating performance of thermal power
plants are taken into account. The main results indicate that the
increasing penetration of wind power in the electricity system will
have significant effects on the combined cycle gas power plants
operation and on the theoretically expected cost reduction and
environmental gains. This research demonstrated the need to address
the impact that energy sources with variable output may have, not
only on the short-term operational planning, but especially on the
medium to long range planning activities, in order to meet the
strategic objectives for the energy sector.
Abstract: In this paper, we introduce a robust state feedback controller design using Linear Matrix Inequalities (LMIs) and guaranteed cost approach for Takagi-Sugeno fuzzy systems. The purpose on this work is to establish a systematic method to design controllers for a class of uncertain linear and non linear systems. Our approach utilizes a certain type of fuzzy systems that are based on Takagi-Sugeno (T-S) fuzzy models to approximate nonlinear systems. We use a robust control methodology to design controllers. This method not only guarantees stability, but also minimizes an upper bound on a linear quadratic performance measure. A simulation example is presented to show the effectiveness of this method.
Abstract: There has been a growing interest in the oxygenation
by plunging water jets in the last few years due to their inherent
advantages, like energy-efficient, low operation cost, etc. Though a
lot of work has been reported on the oxygen-transfer by single
plunging water jets but very few studies have been carried out using
multiple plunging jets. In this paper, volumetric oxygen-transfer
coefficient and oxygen-transfer efficiency has been studied
experimentally for multiple inclined plunging jets (having jet plunge
angle of 60 0 ) in a pool of water for different configurations, in
terms of varying number of jets and jet diameters. This research
suggests that the volumetric oxygen-transfer coefficient and oxygentransfer
efficiency of the multiple inclined plunging jets for air-water
system are significantly higher than those of a single vertical as well
as inclined plunging jet for same flow area and other similar
conditions. The study also reveals that the oxygen-transfer increase
with increase in number of multiple jets under similar conditions,
which will be most advantageous and energy-efficient in practical
situations when large volumes of wastewaters are to be treated. A
relationship between volumetric oxygen-transfer coefficient and jet
parameters is also proposed. The suggested relationship predicts the
volumetric oxygen-transfer coefficient for multiple inclined plunging
jet(s) within a scatter of ±15 percent. The relationship will be quite
useful in scale-up and in deciding optimum configuration of multiple
inclined plunging jet aeration system.