Abstract: This paper presents a computational study of the separated flow in a planer asymmetric diffuser. The steady RANS equations for turbulent incompressible fluid flow and six turbulence closures are used in the present study. The commercial software code, FLUENT 6.3.26, was used for solving the set of governing equations using various turbulence models. Five of the used turbulence models are available directly in the code while the v2-f turbulence model was implemented via User Defined Scalars (UDS) and User Defined Functions (UDF). A series of computational analysis is performed to assess the performance of turbulence models at different grid density. The results show that the standard k-ω, SST k-ω and v2-f models clearly performed better than other models when an adverse pressure gradient was present. The RSM model shows an acceptable agreement with the velocity and turbulent kinetic energy profiles but it failed to predict the location of separation and attachment points. The standard k-ε and the low-Re k- ε delivered very poor results.
Abstract: Researchers have long had trouble in measurement of
Exchangeable Sodium Ratio (ESR) at salt-affected soils. this
parameter are often determined using laborious and time consuming
laboratory tests, but it may be more appropriate and economical to
develop a method which uses a more simple soil salinity index. The
aim of this study was to determine the relationship between
exchangeable sodium ratio (ESR) and sodium adsorption ratio (SAR)
in some salt-affected soils of Khuzestan plain. To this purpose, two
experimental areas (S1, S2) of Khuzestan province-IRAN were
selected and four treatments with three replications by series of
double rings were applied. The treatments were included 25cm,
50cm, 75cm and 100cm water application. The statistical results of
the study indicated that in order to predict soil ESR based on soil
SAR the linear regression model ESR=0.2048+0.0066 SAR
(R2=0.53) & ESR=0.0564+0.0171 SAR (R2=0.76) can be
recommended in Pilot S1 and S2 respectively.
Abstract: The present work is concerned with the free
convective two dimensional flow and heat transfer, in isotropic fluid
filled porous rectangular enclosure with differentially heated walls for
steady state incompressible flow have been investigated for non-
Darcy flow model. Effects of Darcy number (0.0001 £Da£ 10),
Rayleigh number (10 £Ra£ 5000), and aspect ratio (0.25 £AR£ 4), for
a range of porosity (0.4 £e£ 0.9) with and without moving lower wall
have been studied. The cavity was insulated at the lower and upper
surfaces. The right and left heated surfaces allows convective
transport through the porous medium, generating a thermal
stratification and flow circulations. It was found that the Darcy
number, Rayleigh number, aspect ratio, and porosity considerably
influenced characteristics of flow and heat transfer mechanisms. The
results obtained are discussed in terms of the Nusselt number,
vectors, contours, and isotherms.
Abstract: Asynchronous Transfer Mode (ATM) is widely used
in telecommunications systems to send data, video and voice at a
very high speed. In ATM network optimizing the bandwidth through
dynamic routing is an important consideration. Previous research
work shows that traditional optimization heuristics result in suboptimal
solution. In this paper we have explored non-traditional
optimization technique. We propose comparison of two such
algorithms - Genetic Algorithm (GA) and Tabu search (TS), based on
non-traditional Optimization approach, for solving the dynamic
routing problem in ATM networks which in return will optimize the
bandwidth. The optimized bandwidth could mean that some
attractive business applications would become feasible such as high
speed LAN interconnection, teleconferencing etc. We have also
performed a comparative study of the selection mechanisms in GA
and listed the best selection mechanism and a new initialization
technique which improves the efficiency of the GA.
Abstract: The increasing divorce and fertility rates outside of marriage, the changing values in the last decades have led to a high prevalence of single parent families. Currently, worldwide, singleparent families represent about a quarter of all families. Recent changes occurring in the structure of single-parent families and also the multitude of factors that influence the quality of life of these families require the development of new research tools in order to provide foundations for social policies addressed to this type of family. The purpose of this paper is to present an analysis concerning the quality of life for single parent families in Romania, based on data collected through a research methodology developed by the authors within a scientific research project funded by a national grant called Partnerships in priority areas.
Abstract: The scroll pump belongs to the category of positive
displacement pump can be used for continuous pumping of gases at
low pressure apart from general vacuum application. The shape of
volume occupied by the gas moves and deforms continuously as the
spiral orbits. To capture flow features in such domain where mesh
deformation varies with time in a complicated manner, mesh less
solver was found to be very useful. Least Squares Kinetic Upwind
Method (LSKUM) is a kinetic theory based mesh free Euler solver
working on arbitrary distribution of points. Here upwind is enforced
in molecular level based on kinetic flux vector splitting scheme
(KFVS). In the present study we extended the LSKUM to moving
node viscous flow application. This new code LSKUM-NS-MN for
moving node viscous flow is validated for standard airfoil pitching
test case. Simulation performed for flow through scroll pump using
LSKUM-NS-MN code agrees well with the experimental pumping
speed data.
Abstract: (Bi0.5Na0.5)TiO3 doped with 8 mol % BaTiO3 powder
(BNT-BT0.08), prepared by sol-gel method was compacted and
sintered by Spark Plasma Sintering (SPS) process. The influence of
SPS temperature on the densification of BNT-BT0.08 ceramic was
investigated. Starting from sol-gel nanopowder of BNT-BT
containing 8 mol % BaTiO3 with an average particles size of about
30 nm, were obtained ceramics with density around 98 % of the
theoretical density value when the SPS temperature used was about
850 °C. The average grain size of the resulting ceramics was 80 nm.
The BNT-BT0.08 ceramic sample obtained by SPS method has shown
good electric properties at various frequencies.
Abstract: Lighting is not only important for the safety of traffic,
but also it is very important for the protection of pedestrians.
Improvement on visibility in a long distance, lighting, signing,
reduces considerably the risk of accidents in crosswalks. This paper
evaluates different aspects of crosswalks including signing and
lighting to improve road safety.
Abstract: In this paper, we propose disease diagnosis hardware
architecture by using Hypernetworks technique. It can be used to
diagnose 3 different diseases (SPECT Heart, Leukemia, Prostate
cancer). Generally, the disparate diseases require specified diagnosis
hardware model for each disease. Using similarities of three diseases
diagnosis processor, we design diagnosis processor that can diagnose
three different diseases. Our proposed architecture that is combining
three processors to one processor can reduce hardware size without
decrease of the accuracy.
Abstract: Both image steganography and image encryption have
advantages and disadvantages. Steganograhy allows us to hide a
desired image containing confidential information in a covered or
host image while image encryption is decomposing the desired image
to a non-readable, non-comprehended manner. The encryption
methods are usually much more robust than the steganographic ones.
However, they have a high visibility and would provoke the attackers
easily since it usually is obvious from an encrypted image that
something is hidden! The combination of steganography and
encryption will cover both of their weaknesses and therefore, it
increases the security. In this paper an image encryption method
based on sinc-convolution along with using an encryption key of 128
bit length is introduced. Then, the encrypted image is covered by a
host image using a modified version of JSteg steganography
algorithm. This method could be applied to almost all image formats
including TIF, BMP, GIF and JPEG. The experiment results show
that our method is able to hide a desired image with high security and
low visibility.
Abstract: In recent years, an increased competition and lower profit margins have necessitated a focus on improving the performance of the product development process, an area that traditionally have been excluded from detailed steering and evaluation. A systematic improvement requires a good understanding of the current performance, wherefore the interest for product development performance measurement has increased dramatically. This paper presents a case study that evaluates the performance of the product development performance measurement system used in a Swedish company that is a part of a global corporate group. The study is based on internal documentation and eighteen in-depth interviews with stakeholders involved in the product development process. The results from the case study includes a description of what metrics that are in use, how these are employed, and its affect on the quality of the performance measurement system. Especially, the importance of having a well-defined process proved to have a major impact on the quality of the performance measurement system in this particular case.
Abstract: This paper contributes to the debate on the proximate
causes of climate change. Also, it discusses the impact of the global
temperature increases since the beginning of the twentieth century
and the effectiveness of climate change models in isolating the
primary cause (anthropogenic influences or natural variability in
temperature) of the observed temperature increases that occurred
within this period. The paper argues that if climate scientist and
policymakers ignore the anthropogenic influence (greenhouse gases)
on global warming on the pretense of lack of agreement among
various climate models and their inability to account for all the
necessary factors of global warming at all levels the current efforts of
greenhouse emissions control and global warming as a whole could
be exacerbated.
Abstract: This paper illustrates why existing technology
acceptance models are only of limited use for predicting and
explaining the adoption of future information and communication
technologies. It starts with a general overview over technology
adoption processes, and presents several theories for the acceptance
as well as adoption of traditional information technologies. This is
followed by an overview over the recent developments in the area of
information and communication technologies. Based on the
arguments elaborated in these sections, it is shown why the factors
used to predict adoption in existing systems, will not be sufficient for
explaining the adoption of future information and communication
technologies.
Abstract: In recent years, “Bottom-up Planning Approach" has been widely accepted and expanded from planning theorists. Citizen participation becomes more important in decision-making in informal settlements. Many of previous projects and strategies due to ignorance of citizen participation, have been failed facing with informal settlements and in some cases lead physical expansion of these neighbourhoods. According to recent experiences, the new participatory approach was in somehow successful. This paper focuses on local experiences in Iran. A considerable amount of people live in informal settlements in Iran. With the previous methods, the government could not solve the problems of these settlements. It is time to examine new methods such as empowerment of the local citizens and involve them to solve the current physical, social, and economic problems. The paper aims to address the previous and new strategies facing with informal settlements, the conditions under which citizens could be involved in planning process, limits and potentials of this process, the main actors and issues and finally motivations that are able to promote citizen participation. Documentary studies, observation, interview and questionnaire have been used to achieve the above mentioned objectives. Nearly 80 percent of responder in Saadi Community are ready to participate in regularising their neighbourhoods, if pre-conditions of citizen involvement are being provided. These pre-conditions include kind of problem and its severity, the importance of issue, existence of a short-term solution, etc. Moreover, confirmation of dweller-s ownership can promote the citizen engagement in participatory projects.
Abstract: This work attempts to improve the permselectivity of poly-ortho-phenylenediamine (PPD) coating for glutamate biosensor applications on Pt microelectrode, using constant potential amperometry and cyclic voltammetry. Percentage permeability of the modified PPD microelectrode was carried out towards hydrogen peroxide (H2O2) and ascorbic acid (AA) whereas permselectivity represents the percentage interference by AA in H2O2 detection. The 50-μm diameter Pt disk microelectrode showed a good permeability value toward H2O2 (95%) and selectivity against AA (0.01%) compared to other sizes of electrode studied here. The electrode was further modified with glutamate oxidase (GluOx) that was immobilized and cross linked with glutaraldehyde (GA, 0.125%), resulting in Pt/PPD/GluOx-GA electrode design. The maximum current density Jmax and apparent Michaelis constant, KM, obtained on Pt/PPD/GluOx-GA electrodes were 48 μA cm-2 and 50 μM, respectively. The linear region slope (LRS) was 0.96 μA cm-2 mM-1. The detection limit (LOD) for glutamate was 3.0 ± 0.6 μM. This study shows a promising glutamate microbiosensor for brain glutamate detection.
Abstract: In the forming of ceramic materials the plasticity
concept is commonly used. This term is related to a particular
mechanical behavior when clay is mixed with water. A plastic
ceramic material shows a permanent strain without rupture
when a compressive load produces a shear stress that exceeds
the material-s yield strength. For a plastic ceramic body it
observes a measurable elastic behavior before the yield
strength and when the applied load is removed. In this work, a
mathematical model was developed from applied concepts of
the plasticity theory by using the stress/strain diagram under
compression.
Abstract: The microbial production of ethanol from biodiesel¬derived crude glycerol by Enterobacter aerogenes TISTR1468, under micro-aerobic and anaerobic conditions, was investigated. The experimental results showed that micro-aerobic conditions were more favorable for cellular growth (4.0 g/L DCW), ethanol production (20.7 g/L) as well as the ethanol yield (0.47 g/g glycerol) than anaerobic conditions (1.2 g/L DCW, 6.3 g/L ethanol and 0.72 g/g glycerol, respectively). Crude glycerol (100 g/L) was consumed completely with the rate of 1.80 g/L/h. Two-stage fermentation (combination of micro-aerobic and anaerobic condition) exhibited higher ethanol production (24.5 g/L) than using one-stage fermentation (either micro-aerobic or anaerobic condition. The two- stage configuration, exhibited slightly higher crude glycerol consumption rate (1.81 g/L/h), as well as ethanol yield (0.56 g/g) than the one-stage configuration. Therefore, two-stage process was selected for ethanol production from E. aerogenes TISTR1468 in scale-up studies.
Abstract: The aim of a biological model is to understand the
integrated structure and behavior of complex biological systems as a
function of the underlying molecular networks to achieve simulation
and forecast of their operation. Although several approaches have
been introduced to take into account structural and environment
related features, relatively little attention has been given to represent
the behavior of biological systems. The Abstract Biological Process
(ABP) model illustrated in this paper is an object-oriented model
based on UML (the standard object-oriented language). Its main
objective is to bring into focus the functional aspects of the
biological system under analysis.
Abstract: The present paper is oriented to problems of simulation of anticipatory systems, namely those that use simulation models for the aid of anticipation. A certain analogy between use of simulation and imagining will be applied to make the explication more comprehensible. The paper will be completed by notes of problems and by some existing applications. The problems consist in the fact that simulation of the mentioned anticipatory systems end is simulation of simulating systems, i.e. in computer models handling two or more modeled time axes that should be mapped to real time flow in a nondescent manner. Languages oriented to objects, processes and blocks can be used to surmount the problems.
Abstract: The main aims in this research are to study the solid
waste generation in the Faculty of Engineering and Built
Environment in the UKM and at the same time to determine
composition and some of the waste characteristics likewise: moisture
content, density, pH and C/N ratio. For this purpose multiple
campaigns were conducted to collect the wastes produced in all
hostels, faculties, offices and so on, during 24th of February till 2nd
of March 2009, measure and investigate them with regard to both
physical and chemical characteristics leading to highlight the
necessary management policies. Research locations are Faculty of
Engineering and the Canteen nearby that. From the result gained, the
most suitable solid waste management solution will be proposed to
UKM. The average solid waste generation rate in UKM is 203.38
kg/day. The composition of solid waste generated are glass, plastic,
metal, aluminum, organic and inorganic waste and others waste.
From the laboratory result, the average moisture content, density, pH
and C/N ratio values from the solid waste generated are 49.74%,
165.1 kg/m3, 5.3, and 7:1 respectively. Since, the food waste (organic
waste) were the most dominant component, around 62% from the
total waste generated hence, the most suitable solid waste
management solution is composting.