Abstract: Oases are complex and fragile agro-ecosystems. They
have always existed in environments characterized by an arid climate,
scarcity of rainfall, high temperatures and high evaporation. These
palms have grown up despite the severity of the physical
characteristics thanks to the water's existence and irrigation practice.
The oases are generally spread along non-perennial rivers (wadis),
shallow water table or deep artesian groundwater. However, the
sustainability of oasis system is threatened by water scarcity and
declining of water table levels particularly in arid areas. Located in
the southern east area of Morocco, Tafilalet plain encompasses one of
the largest palm groves in the kingdom. In recent years, this area has
become increasingly threatened by water shortage and has seen a
sharp deterioration under the effect of several combined
anthropogenic and climatic factors. The Bayoud disease, successive
years of drought, Hassan Addakhil dam construction etc are all
factors that have affected both water and phoenicicole heritage of the
area. The objective of this study is to understand the interaction
between qualitative and quantitative degradation of groundwater
resources, and the palm grove dynamics, while reviewing the
assumption that groundwater resources contribute in a direct way to
the conservation of this oasis agroecosystem. A historical analysis
tracing both the oasis dynamics and the groundwater evolution has
been established. Data were collected from satellite images, surveys
with different actors (farmers, Regional Office for Agricultural
Development, Basin agency...). They were complemented by a
synthesis of numerous technical reports in the area. The results
showed that within 40 years, the thickness of the groundwater table
has dropped in 50 %. Along with this, there has been a downsizing of
date palm by 50 %. Areas with higher groundwater level were the
least affected by the downsizing. So we can say that the shallow
groundwater contribute significantly and directly to the water supply
of date palm through its root system, and largely ensures the oasis
ecosystem sustainability.
Abstract: Currently, seismic probabilistic risk assessments
(SPRA) for nuclear facilities use In-Structure Response Spectra
(ISRS) in the calculation of fragilities for systems and components.
ISRS are calculated via dynamic analyses of the host building
subjected to two orthogonal components of horizontal ground
motion. Each component is defined as the median motion in any
horizontal direction. Structural engineers applied the components
along selected X and Y Cartesian axes. The ISRS at different
locations in the building are also calculated in the X and Y directions.
The choice of the directions of X and Y are not specified by the
ground motion model with respect to geographic coordinates, and are
rather arbitrarily selected by the structural engineer. Normally, X and
Y coincide with the “principal” axes of the building, in the
understanding that this practice is generally conservative. For SPRA
purposes, however, it is desirable to remove any conservatism in the
estimates of median ISRS. This paper examines the effects of the
direction of horizontal seismic motion on the ISRS on typical nuclear
structure. We also evaluate the variability of ISRS calculated along
different horizontal directions. Our results indicate that some central
measures of the ISRS provide robust estimates that are practically
independent of the selection of the directions of the horizontal
Cartesian axes.
Abstract: Augmented Reality is a technology that involves the
overlay of virtual content, which is context or environment sensitive,
on images of the physical world in real time. This paper presents the
development of a catalog system that facilitates and allows the
creation, publishing, management and exploitation of augmented
multimedia contents and Augmented Reality applications, creating an
own space for anyone that wants to provide information to real
objects in order to edit and share it then online with others. These
spaces would be built for different domains without the initial need of
expert users. Its operation focuses on the context of Web 2.0 or
Social Web, with its various applications, developing contents to
enrich the real context in which human beings act permitting the
evolution of catalog’s contents in an emerging way.
Abstract: Key frame extraction methods select the most
representative frames of a video, which can be used in different areas
of video processing such as video retrieval, video summary, and video
indexing. In this paper we present a novel approach for extracting key
frames from video sequences. The frame is characterized uniquely by
his contours which are represented by the dominant blocks. These
dominant blocks are located on the contours and its near textures.
When the video frames have a noticeable changement, its dominant
blocks changed, then we can extracte a key frame. The dominant
blocks of every frame is computed, and then feature vectors are
extracted from the dominant blocks image of each frame and arranged
in a feature matrix. Singular Value Decomposition is used to calculate
sliding windows ranks of those matrices. Finally the computed ranks
are traced and then we are able to extract key frames of a video.
Experimental results show that the proposed approach is robust
against a large range of digital effects used during shot transition.
Abstract: Maturity models, used descriptively to explain
changes in reality or normatively to guide managers to make
interventions to make organizations more effective and efficient, are
based on the principles of statistical quality control and PDCA
continuous improvement (Plan, Do, Check, Act). Some frameworks
developed over the concept of maturity models include COBIT,
CMM, and ITIL.
This paper presents some limitations of traditional maturity
models, most of them related to the mechanistic and reductionist
principles over which those models are built. As systems theory helps
the understanding of the dynamics of organizations and
organizational change, the development of a systemic maturity model
can help to overcome some of those limitations.
This document proposes a systemic maturity model, based on a
systemic conceptualization of organizations, focused on the study of
the functioning of the parties, the relationships among them, and their
behavior as a whole. The concept of maturity from the system theory
perspective is conceptually defined as an emergent property of the
organization, which arises as a result of the degree of alignment and
integration of their processes. This concept is operationalized through
a systemic function that measures the maturity of organizations, and
finally validated by the measuring of maturity in some organizations.
For its operationalization and validation, the model was applied to
measure the maturity of organizational Governance, Risk and
Compliance (GRC) processes.
Abstract: The reliability of the filtered HVBK model is now
investigated via some large eddy simulations (LES) of freely
decaying isotropic superfluid turbulence. For homogeneous
turbulence at very high Reynolds numbers, comparison of the terms
in the spectral kinetic energy budget equation indicates, in the
energy-containing range, that the production and energy transfer
effects become significant except for dissipation. In the inertial range,
where the two fluids are perfectly locked, the mutual friction maybe
neglected with respect to other terms. Also, the LES results for the
other terms of the energy balance are presented.
Abstract: This work is focused on the study of valuation of
recycled concrete aggregates, by measuring certain properties of
concrete in the fresh and hardened state. In this study, rheological
tests and physic-mechanical characterization on concretes and
mortars were conducted with recycled concrete whose geometric
properties were identified aggregates. Mortars were elaborated with
recycled fine aggregate (0/5mm) and concretes were manufactured
using recycled coarse aggregates (5/12.5 mm and 12.5/20 mm). First,
a study of the mortars was conducted to determine the effectiveness
of polycarboxylate superplasticizer on the workability of these and
their action deflocculating of the recycled sand. The rheological
behavior of mortars based on fine aggregate recycled was
characterized. The results confirm that the mortars composed of
different fractions of recycled sand (0 /5) have a better mechanical
properties (compressive and flexural strength) compared to normal
mortar. Also, the mechanical strengths of concretes made with
recycled aggregates (5/12.5 mm and 12.5/20 mm), are comparable to
those of conventional concrete with conventional aggregates,
provided that the implementation can be improved by the addition of
a superplasticizer.
Abstract: The knowledge of biodiesel density over large ranges
of temperature and pressure is important for predicting the behavior
of fuel injection and combustion systems in diesel engines, and for
the optimization of such systems. In this study, cottonseed oil was
transesterified into biodiesel and its density was measured at
temperatures between 288 K and 358 K and pressures between 0.1
MPa and 30 MPa, with expanded uncertainty estimated as ±1.6 kg⋅m-
3. Experimental pressure-volume-temperature (pVT) cottonseed data
was used along with literature data relative to other 18 biodiesels, in
order to build a database used to test the correlation of density with
temperarure and pressure using the Goharshadi–Morsali–Abbaspour
equation of state (GMA EoS). To our knowledge, this is the first that
density measurements are presented for cottonseed biodiesel under
such high pressures, and the GMA EoS used to model biodiesel
density. The new tested EoS allowed correlations within 0.2 kg·m-3
corresponding to average relative deviations within 0.02%. The built
database was used to develop and test a new full predictive model
derived from the observed linear relation between density and degree
of unsaturation (DU), which depended from biodiesel FAMEs
profile. The average density deviation of this method was only about
3 kg.m-3 within the temperature and pressure limits of application.
These results represent appreciable improvements in the context of
density prediction at high pressure when compared with other
equations of state.
Abstract: We propose a new alternative method for imposing
fluid-solid boundary conditions in simulations of Multiparticle
Collision Dynamics. Our method is based on the introduction of
an explicit potential force acting between the fluid particles and a
surface representing a solid boundary. We show that our method can
be used in simulations of plane Poiseuille flows. Important quantities
characterizing the flow and the fluid-solid interaction like the slip
coefficient at the solid boundary and the effective viscosity of the
fluid, are measured in terms of the set of independent parameters
defining the numerical implementation. We find that our method can
be used to simulate the correct hydrodynamic flow within a wide
range of values of these parameters.
Abstract: India holds 17.5% of the world’s population but has
only 2% of the total geographical area of the world where 27.35% of
the area is categorized as wasteland due to lack of or less
groundwater. So there is a demand for excessive groundwater for
agricultural and non agricultural activities to balance its growth rate.
With this in mind, an attempt is made to find the groundwater
potential zone in Gomukhi Nadhi sub basin of Vellar River basin,
TamilNadu, India covering an area of 1146.6 Sq.Km consists of 9
blocks from Peddanaickanpalayam to Virudhachalam in the sub
basin. The thematic maps such as Geology, Geomorphology,
Lineament, Landuse and Landcover and Drainage are prepared for
the study area using IRS P6 data. The collateral data includes rainfall,
water level, soil map are collected for analysis and inference. The
digital elevation model (DEM) is generated using Shuttle Radar
Topographic Mission (SRTM) and the slope of the study area is
obtained. ArcGIS 10.1 acts as a powerful spatial analysis tool to find
out the ground water potential zones in the study area by means of
weighted overlay analysis. Each individual parameter of the thematic
maps are ranked and weighted in accordance with their influence to
increase the water level in the ground. The potential zones in the
study area are classified viz., Very Good, Good, Moderate, Poor with
its aerial extent of 15.67, 381.06, 575.38, 174.49 Sq.Km respectively.
Abstract: This paper contains 2 main parts. In the first part of paper we simulated and studied three types of electrode patterns used in various industries for suspension and handling of the semiconductor and glass and we selected the best pattern by evaluating the electrostatic force, which was comb pattern electrode.
In the second part we investigated the parameters affecting the amount of electrostatic force such as the gap between surface and electrode (g), the electrode width (w), the gap between electrodes (t), the surface permittivity and electrode length and methods of improvement of adhesion force by changing these values.
Abstract: Reduction of CO2 emissions has become a priority for
several countries due to increasing concerns about global warming
and climate change, especially in the developed countries. Residential
sector is considered one of the most important sectors for
considerable reduction of CO2 emissions since it represents a
significant amount of the total consumed energy in those countries. A
significant CO2 reduction cannot be achieved unless some initiatives
have been adopted in the policy of these countries. Introducing micro
combined heat and power (!CHP) systems into residential energy
systems is one of these initiatives, since such a technology offers
several advantages. Moreover, !CHP technology has the opportunity
to be operated not only by natural gas but it could also be operated by
renewable fuels. However, this technology can be operated by
different operation strategies. Each strategy has some advantages and
disadvantages.
This paper provides a review of different operation strategies of
such a technology used for residential energy systems, especially for
single dwellings. The review summarizes key points that outline the
trend of previous research carried out in this field.
Abstract: Heightened concerns over the amount of carbon
emitted from coal-related processes are generating shifts to the
application of biomass. In co-gasification, where coal is gasified
along with biomass, the biomass may be fed together with coal (cofeeding)
or an independent biomass gasifier needs to be integrated
with the coal gasifier. The main aim of this work is to evaluate the
biomass introduction methods in coal co-gasification. This includes
the evaluation of biomass concentration input (B0 to B100) and its
gasification performance. A process model is developed and
simulated in Aspen HYSYS, where both coal and biomass are
modelled according to its ultimate analysis. It was found that the
syngas produced increased with increasing biomass content for both
co-feeding and independent schemes. However, the heating values
and heat duties decreases with biomass concentration as more CO2
are produced from complete combustion.
Abstract: Medical imaging produces human body pictures in
digital form. Since these imaging techniques produce prohibitive
amounts of data, compression is necessary for storage and
communication purposes. Many current compression schemes
provide a very high compression rate but with considerable loss of
quality. On the other hand, in some areas in medicine, it may be
sufficient to maintain high image quality only in region of interest
(ROI). This paper discusses a contribution to the lossless
compression in the region of interest of Scintigraphic images based
on SPIHT algorithm and global transform thresholding using
Huffman coding.
Abstract: Inland Waterway Transportation (IWT) is playing an
important role in national transport systems, water transportation is
considered to be safe, energy efficient and environmentally friendly
mode of transport, all benefits of IWT cause national awareness
increase, for instance the Colombian government is planning to
restore the navigability of the most important river of the country, the
Magdalena’s River navigability, embrace waterway transportation in
Colombia could strength competitiveness while reduce most of the
transport externalities. However, the current situation of the
Magdalena is deplorable, the most important river of Colombia has
been abandoned for decades and the solution is beyond of a single
administrative entity. This paper analyzes the outcomes of the
Navigation And Inland Waterway Action and Development in
Europe program (NAIADES) as a prospective to develop a similar
program in Colombia with similar objectives and guidelines,
considering sustainability, guarantying the long-term future results
and adaptability of the program. Identifying stakeholders and policy
experts, a set of individual interviews were carried out; findings
support the idea of lack of integration within governmental
institutions and lack of importance in marketing promotion as
possible drawbacks on the implementation of IWT projects.
Abstract: Time and cost are the main goals of the construction
project management. The first schedule developed may not be a
suitable schedule for beginning or completing the project to achieve
the target completion time at a minimum total cost. In general, there
are trade-offs between time and cost (TCT) to complete the activities
of a project. This research presents genetic algorithms (GAs) multiobjective
model for project scheduling considering different
scenarios such as least cost, least time, and target time.
Abstract: Collapsible soils go through radical rearrangement of
their particles when triggered by water, stress or/and vibration,
causing loss of volume. This loss of volume in soil as seen in
foundation failures has caused millions of dollars’ worth of damages
to public facilities and infrastructure and so has an adverse effect on
the society and people. Despite these consequences and the several
studies that are available, more research is still required in the study
of soil collapsibility. Discerning the pedogenesis (formation) of soils
and investigating the combined effects of the different geological soil
properties is key to elucidating and quantifying soils collapsibility.
This study presents a novel laboratory testing regime that would be
undertaken on soil samples where the effects of soil type, compactive
variables (moisture content, density, void ratio, degree of saturation)
and loading are analyzed. It is anticipated that results obtained would
be useful in mapping the trend of the combined effect thus the basis
for evaluating soil collapsibility or collapse potentials encountered in
construction with volume loss problems attributed to collapse.
Abstract: South Africa has some regions which are susceptible
to moderate seismic activity. A peak ground acceleration of between
0.1g and 0.15g can be expected in the southern parts of the Western
Cape. Unreinforced Masonry (URM) is commonly used as a
construction material for 2 to 5 storey buildings in underprivileged
areas in and around Cape Town. URM is typically regarded as the
material most vulnerable to damage when subjected to earthquake
excitation. In this study, a three-storey URM building was analysed
by applying seven earthquake time-histories, which can be expected
to occur in South Africa using a finite element approach.
Experimental data was used to calibrate the in- and out-of-plane
stiffness of the URM. The results indicated that tensile cracking of
the in-plane piers was the dominant failure mode. It is concluded that
URM buildings of this type are at risk of failure especially if
sufficient ductility is not provided. The results also showed that
connection failure must be investigated further.
Abstract: Columns have traditionally been constructed of
reinforced concrete or structural steel. Much attention was allocated
to estimate the axial capacity of the traditional column sections to the
detriment of other forms of construction. Other forms of column
construction such as Concrete Filled Double Skin Tubes received
little research attention, and almost no attention when subjected to
eccentric loading. This paper investigates the axial capacity of
columns when subjected to eccentric loading. The experimental axial
capacities are compared to other established theoretical formulae on
concentric loading to determine a possible relationship. The study
found a good correlation between the reduction in axial capacity for
different column lengths and hollow section ratios.
Abstract: This paper discusses about the findings of preliminary
survey on MATLAB software learning among power electronics
students. One of the main focuses of power electronics course is on
DC to DC boost convertors, because boost convertors are generally
used in different industrial and non industrial applications. Population
samples of this study were randomly selected final year bachelor of
electronics and electrical engineering students from University Tun
Hussein Onn Malaysia (UTHM).As per the results from the survey
questioner analysis, almost eighty percent students are facing
problem and difficulties in Dc to Dc boost convertors experimental
understanding without using MATLAB simulink package. As per
finding of this study it is clear that MATLAB play an effective and
efficient function for better understanding of boost convertors
experimental work among power electronics learners.