Abstract: Factors affecting construction unit cost vary
depending on a country’s political, economic, social and
technological inclinations. Factors affecting construction costs have
been studied from various perspectives. Analysis of cost factors
requires an appreciation of a country’s practices. Identified cost
factors provide an indication of a country’s construction economic
strata. The purpose of this paper is to identify the essential factors
that affect unit cost estimation and their breakdown using artificial
neural networks. Twenty five (25) identified cost factors in road
construction were subjected to a questionnaire survey and employing
SPSS factor analysis the factors were reduced to eight. The 8 factors
were analysed using neural network (NN) to determine the
proportionate breakdown of the cost factors in a given construction
unit rate. NN predicted that political environment accounted 44% of
the unit rate followed by contractor capacity at 22% and financial
delays, project feasibility and overhead & profit each at 11%. Project
location, material availability and corruption perception index had
minimal impact on the unit cost from the training data provided.
Quantified cost factors can be incorporated in unit cost estimation
models (UCEM) to produce more accurate estimates. This can create
improvements in the cost estimation of infrastructure projects and
establish a benchmark standard to assist the process of alignment of
work practises and training of new staff, permitting the on-going
development of best practises in cost estimation to become more
effective.
Abstract: This paper presents a new structure of microstrip band
pass filter (BPF) based on coupled stepped impedance resonators.
Each filter consists of two coupled stepped impedance resonators
connected to microstrip feed lines. The coupled junction is utilized to
connect the two BPFs to the antenna. This two band pass filters are
designed and simulated to operate for the digital communication
system (DCS) and Industrial Scientific and Medical (ISM) bands at
1.8 GHz and 2.45 GHz respectively. The proposed circuit presents
good performances with an insertion loss lower than 2.3 dB and
isolation between the two channels greater than 21 dB. The prototype
of the optimized diplexer have been investigated numerically by
using ADS Agilent and verified with CST microwave software.
Abstract: Over the last few decades, oilfield service rolling
equipment has significantly increased in weight, primarily because of
emissions regulations, which require larger/heavier engines, larger
cooling systems, and emissions after-treatment systems, in some
cases, etc. Larger engines cause more vibration and shock loads,
leading to failure of electronics and control systems.
If the vibrating frequency of the engine matches the system
frequency, high resonance is observed on structural parts and mounts.
One such existing automated control equipment system comprising
wire rope mounts used for mounting computers was designed
approximately 12 years ago. This includes the use of an industrialgrade
computer to control the system operation. The original
computer had a smaller, lighter enclosure. After a few years, a newer
computer version was introduced, which was 10 lbm heavier. Some
failures of internal computer parts have been documented for cases in
which the old mounts were used. Because of the added weight, there
is a possibility of having the two brackets impact each other under
off-road conditions, which causes a high shock input to the computer
parts. This added failure mode requires validating the existing mount
design to suit the new heavy-weight computer.
This paper discusses the modal finite element method (FEM)
analysis and experimental modal analysis conducted to study the
effects of vibration on the wire rope mounts and the computer. The
existing mount was modelled in ANSYS software, and resultant
mode shapes and frequencies were obtained. The experimental modal
analysis was conducted, and actual frequency responses were
observed and recorded.
Results clearly revealed that at resonance frequency, the brackets
were colliding and potentially causing damage to computer parts. To
solve this issue, spring mounts of different stiffness were modeled in
ANSYS software, and the resonant frequency was determined.
Increasing the stiffness of the system increased the resonant
frequency zone away from the frequency window at which the engine
showed heavy vibrations or resonance. After multiple iterations in
ANSYS software, the stiffness of the spring mount was finalized,
which was again experimentally validated.
Abstract: The paper examines the interaction between the
environmental taxation, size of government spending on
environmental protection and greenhouse gas emissions and gross
inland energy consumption. The aim is to analyze the effects of
environmental taxation and government spending on environmental
protection as an environmental policy instruments on greenhouse gas
emissions and gross inland energy consumption in the EU15. The
empirical study is performed using a VAR approach with the
application of aggregated data of EU15 over the period 1995 to 2012.
The results provide the evidence that the reactions of greenhouse gas
emission and gross inland energy consumption to the shocks of
environmental policy instruments are strong, mainly in the short term
and decay to zero after about 8 years. Further, the reactions of the
environmental policy instruments to the shocks of greenhouse gas
emission and gross inland energy consumption are also strong in the
short term, however with the deferred effects. In addition, the results
show that government spending on environmental protection together
with gross inland energy consumption has stronger effect on
greenhouse gas emissions than environmental taxes in EU15 over the
examined period.
Abstract: Periventricular Leukomalacia (PVL) is a White Matter
Injury (WMI) of preterm neonatal brain. Objectives of the study were
to assess the neuro-developmental outcome at one year of age and to
determine a good protocol of cranial ultrasonography to detect PVL.
Two hundred and sixty four preterm neonates were included in the
study. Series of cranial ultrasound scans were done by using a
dedicated neonatal head probe 4-10 MHz of Logic e portable
ultrasound scanner. Clinical history of seizures, abnormal head
growth (hydrocephalus or microcephaly) and developmental
milestones were assessed and neurological examinations were done
until one year of age. Among live neonates, 57% who had cystic PVL
(Grades 2 and 3) manifested as cerebral palsy. In conclusion cystic
PVL has permanent neurological disabilities like cerebral palsy.
Good protocol of real time cranial ultrasonography to detect PVL is
to perform scans at least once a week until one month and at term (40
weeks of gestation).
Abstract: With a long history, dual-task has become one of the
most intriguing research fields regarding human brain functioning
and cognition. However, findings considering effects of taskinterrelations
are limited (especially, in combined motor and
cognitive tasks). Therefore, we aimed at developing a measurement
system in order to analyse interrelation effects of cognitive and motor
tasks. On the one hand, the present study demonstrates the
applicability of the measurement system and on the other hand first
results regarding a systematisation of different task combinations are
shown. Future investigations should combine imagine technologies
and this developed measurement system.
Abstract: The problematic of gender and socioeconomic status
biased differences in academic motivation patterns is discussed.
Gender identity is understood according to symbolic interactionism
perspective: as a result of reflected appraisals, social comparisons,
self-attributions, and identifications, shaped by social environment
and family context. The effects of socioeconomic status on academic
motivation are conceptualized according to Bourdieu’s habitus
concept, reflecting the role of unconscious and internalized cultural
signals, proper to low and high socioeconomic status family contexts.
Since families differ by various socioeconomic features, the
hypothesis about possible impact of parents’ socioeconomic status on
their children’s academic motivation interfering with gender
socialization effects is held. The survey, aiming to seize gender
differences in academic motivation and self-recorded improvementoriented
efforts as a result of socialization processes operating in the
families of low and high socioeconomic status, was designed. The
results of Lithuanian higher education students’ survey are presented
and discussed.
Abstract: Container handling problems at container terminals
are NP-hard problems. This paper presents an approach using
discrete-event simulation modeling to optimize solution for storage
space allocation problem, taking into account all various interrelated
container terminal handling activities. The proposed approach is
applied on a real case study data of container terminal at Alexandria
port. The computational results show the effectiveness of the
proposed model for optimization of storage space allocation in
container terminal where 54% reduction in containers handling time
in port is achieved.
Abstract: The paper focus on robotic telepresence system build
around humanoid robot operated with controller-less Wizard of Oz
technique. Proposed solution gives possibility to quick start acting as
a operator with short, if any, initial training.
Abstract: The tomato is a very important crop, whose
cultivation in the Mediterranean basin is severely affected by the
phytoparasitic weed Phelipanche ramosa. The semiarid regions of
the world are considered the main areas where this parasitic weed is
established causing heavy infestation as it is able to produce high
numbers of seeds (up to 500,000 per plant), which remain viable for
extended period (more than 20 years). In this paper the results
obtained from eleven treatments in order to control this parasitic
weed including chemical, agronomic, biological and biotechnological
methods compared with the untreated test under two plowing depths
(30 and 50 cm) are reported. The split-plot design with 3 replicates
was adopted. In 2014 a trial was performed in Foggia province
(southern Italy) on processing tomato (cv Docet) grown in the field
infested by Phelipanche ramosa. Tomato seedlings were transplant
on May 5, on a clay-loam soil. During the growing cycle of the
tomato crop, at 56-78 and 92 days after transplantation, the number
of parasitic shoots emerged in each plot was detected. At tomato
harvesting, on August 18, the major quantity-quality yield parameters
were determined (marketable yield, mean weight, dry matter, pH,
soluble solids and color of fruits). All data were subjected to analysis
of variance (ANOVA) and the means were compared by Tukey's test.
Each treatment studied did not provide complete control against
Phelipanche ramosa. However, among the different methods tested,
some of them which Fusarium, gliphosate, radicon biostimulant and
Red Setter tomato cv (improved genotypes obtained by Tilling
technology) under deeper plowing (50 cm depth) proved to mitigate
the virulence of the Phelipanche ramose attacks. It is assumed that
these effects can be improved combining some of these treatments
each other, especially for a gradual and continuing reduction of the
“seed bank” of the parasite in the soil.
Abstract: Learning through creation of contextual games is a
very promising approach when undertaking interdisciplinary and
international group projects. During 2013 and 2014 the authors
organized two intensive student projects. The two projects were in
different countries and different conditions. Between them, the two
projects involved 68 students and 12 mentors from five EU countries
and from various academic disciplines. In this paper we share our
experience of these two projects and we suggest approaches that can
be utilized to strengthen the chances of succeeding in short (12-15
days long) intensive student projects.
Abstract: This work presents a new planar multiband antenna
based on fractal geometry. This structure is optimized and validated
into simulation by using CST-MW Studio. To feed this antenna we
have used a CPW line which makes it easy to be incorporated with
integrated circuits. The simulation results presents a good matching
input impedance and radiation pattern in the GSM band at 900 MHz
and ISM band at 2.4 GHz. The final structure is a dual band fractal
antenna with 70 x 70 mm² as a total area by using an FR4 substrate.
Abstract: This paper presents a novel design of a microstrip
fractal antenna based on the use of Sierpinski triangle shape, it’s
designed and simulated by using FR4 substrate in the operating
frequency bands (GPS, WiMAX), the design is a fractal antenna with
a modified ground structure. The proposed antenna is simulated and
validated by using CST Microwave Studio Software, the simulated
results presents good performances in term of radiation pattern and
matching input impedance.
Abstract: Logistics distributors face the issue of having to
provide increasing service levels while being forced to reduce costs at
the same time. Same-day delivery, quick order processing and rapidly
growing ranges of articles are only some of the prevailing challenges.
One key aspect of the performance of an intra-logistics system is how
often and in which amplitude congestions and dysfunctions affect the
processing operations. By gaining knowledge of the so called
‘performance availability’ of such a system during the planning stage,
oversizing and wasting can be reduced whereas planning
transparency is increased. State of the art for the determination of this
KPI is simulation studies. However, their structure and therefore their
results may vary unforeseeably. This article proposes a concept for
the establishment of ‘certified’ and hence reliable and comparable
simulation models.
Abstract: Near infrared (NIR) spectroscopy has always been of
great interest in the food and agriculture industries. The development
of prediction models has facilitated the estimation process in recent
years. In this study, 110 crude palm oil (CPO) samples were used to
build a free fatty acid (FFA) prediction model. 60% of the collected
data were used for training purposes and the remaining 40% used for
testing. The visible peaks on the NIR spectrum were at 1725 nm and
1760 nm, indicating the existence of the first overtone of C-H bands.
Principal component regression (PCR) was applied to the data in
order to build this mathematical prediction model. The optimal
number of principal components was 10. The results showed
R2=0.7147 for the training set and R2=0.6404 for the testing set.
Abstract: To develop AZ91D magnesium alloys with improved
properties, we have applied TiN and VN/TiN multilayer coatings
using DC magnetron sputter technique. Coating structure, surface
morphology, chemical bonding and corrosion resistance of coatings
were analyzed by x-ray diffraction (XRD), scanning electron
microscope (SEM), x-ray photoelectron spectroscopy (XPS), and
tafel extrapolation method, respectively. XPS analysis reveal that VN
overlayer reacts with oxygen at the VN/TiN interface and forms more
stable TiN layer. Morphological investigations and the corrosion
results show that VN/TiN multilayer thin film coatings are quite
effective to optimize the corrosion resistance of Mg alloys.
Abstract: Machining parameters are very important in
determining the surface quality of any material. In the past decade,
some new engineering materials were developed for the
manufacturing industry which created a need to conduct an
investigation on the impact of the said parameters on their surface
roughness. Polyurethane (PU) block is widely used in the automotive
industry to manufacture parts such as checking fixtures that are used
to verify the dimensional accuracy of automotive parts. In this paper,
the design of experiment (DOE) was used to investigate on the effect
of the milling parameters on the PU block. Furthermore, an analysis
of the machined surface chemical composition was done using
scanning electron microscope (SEM). It was found that the surface
roughness of the PU block is severely affected when PU undergoes a
flood machining process instead of a dry condition. In addition the
stepover and the silicon content were found to be the most significant
parameters that influence the surface quality of the PU block.
Abstract: Safety is one of the most important considerations
when buying a new car. While active safety aims at avoiding
accidents, passive safety systems such as airbags and seat belts
protect the occupant in case of an accident. In addition to legal
regulations, organizations like Euro NCAP provide consumers with
an independent assessment of the safety performance of cars and
drive the development of safety systems in automobile industry.
Those ratings are mainly based on injury assessment reference values
derived from physical parameters measured in dummies during a car
crash test.
The components and sub-systems of a safety system are designed
to achieve the required restraint performance. Sled tests and other
types of tests are then carried out by car makers and their suppliers
to confirm the protection level of the safety system. A Knowledge
Discovery in Databases (KDD) process is proposed in order to
minimize the number of tests. The KDD process is based on the
data emerging from sled tests according to Euro NCAP specifications.
About 30 parameters of the passive safety systems from different data
sources (crash data, dummy protocol) are first analysed together with
experts opinions. A procedure is proposed to manage missing data
and validated on real data sets. Finally, a procedure is developed to
estimate a set of rough initial parameters of the passive system before
testing aiming at reducing the number of tests.
Abstract: Bamboo is extensively used in construction industry.
Low durability of bamboo due to fungus infestation and termites
attack under storage puts certain constrains for it usage as modern
structural material. Looking at many chemical formulations for
bamboo treatment leading to severe harmful environment effects,
research on eco-friendly preservatives for bamboo treatment has been
initiated world-over. In the present studies, eco-friendly preservative
for bamboo treatment has been developed. To validate its application
for structural purposes, investigation of effect of treatment on
compressive strength has been investigated. Neemoil (25%)
integrated with copper naphthenate (0.3%) on dilution with kerosene
oil impregnated into bamboo culm at 2 bar pressure, has shown
weight loss of only 3.15% in soil block analysis method. The results
from compressive strength analysis using HEICO Automatic
Compression Testing Machine reveal that preservative treatment has
not altered the structural properties of bamboo culms. Compressive
strength of control (11.72 N/mm2) and above treated samples (11.71
N/mm2) was found to be comparable.
Abstract: Lead being a toxic heavy metal that mankind is
exposed to the highest levels of this metal from environmental
pollutants. A total of 180 Male scalp hair samples were collected
from different environments in Greater Cairo (GC), i.e. industrial,
heavy traffic and rural areas (60 samples from each) having different
activities during the period of, 1/5/2010 to 1/11/2012. Hair samples
were collected during five stages. Data proved that the concentration
of lead in male industrial areas of Cairo ranged between 6.2847 to
19.0432 μg/g, with mean value of 12.3288 μg/g. On the other hand,
lead content of hair samples of residential-traffic areas ranged
between 2.8634 to 16.3311 μg/g with mean value of 9.7552 μg/g.
While lead concentration on the hair of the male residents living in
rural area ranged between 1.0499-9.0402μg/g with mean value of
4.7327 μg/g. The Pb concentration in scalp hair of Cairo residents of
residential-traffic and rural traffic areas was observed to follow the
same pattern. The pattern was that of decrease concentration of
summer and its increase in winter. Then, there was a marked increase
in Pb concentration of summer 2012, and this increase was
significant. These were obviously seen for the residential-traffic and
rural areas residents. Pb pollution in residents of industrial areas
showed the same seasonal pattern, but there was marked to decrease
in Pb concentration of summer 2012, and this decrease was
significant. Lead pollution in residents of GC was serious. It is worth
noting that the atmosphere is still contaminated by lead despite a
decade of using unleaded gasoline. Strong seasonal variation in
higher Pb concentration on winter than in summer was found. Major
contributions to the pollution with Pb could include industry
emissions, motor vehicle emissions and long transported dust from
outside Cairo. More attention should be paid to the reduction of Pb
content of the urban aerosol and to the Pb pollution health.