Abstract: This paper presents the results and findings from a
parametric study on the water surface elevation at upstream of bridge
constriction for subcritical flow. In this study, the influence of
Manning's Roughness Coefficient of main channel (nmc) and
floodplain (nfp), and bridge opening (b) flow rate (Q), contraction
(kcon) and expansion coefficients (kexp) were investigated on
backwater level. The DECK bridge models with different span widths
and without any pier were investigated within the two stage channel
having various roughness conditions. One of the most commonly
used commercial one-dimensional HEC-RAS model was used in this
parametric study. This study showed that the effects of main channel
roughness (nmc) and flow rate (Q) on the backwater level are much
higher than those of the floodplain roughness (nfp). Bridge opening
(b) with contraction (kcon) and expansion coefficients (kexp) have very
little effect on the backwater level within this range of parameters.
Abstract: This paper develops and extended eclectic paradigm
to fit the firm internationalization process with the real international
business world. The approach is based on Dunning´s, introducing
new concepts like mode of entry, international joint venture o
international mergers and acquisitions. At the same time is presented
a model to describe the Spanish international mergers and
acquisitions in order to determinate the most important factor that
influence in this type of foreign direct investment.
Abstract: Ti6Al4V alloy is highly used in the automotive and
aerospace industry due to its good machining characteristics. Micro
EDM drilling is commonly used to drill micro hole on extremely hard
material with very high depth to diameter ratio. In this study, the
parameters of micro-electrical discharge machining (EDM) in drilling
of Ti6Al4V alloy is optimized for higher machining accuracy with
less hole-dilation and hole taper ratio. The micro-EDM machining
parameters includes, peak current and pulse on time. Fuzzy analysis
was developed to evaluate the machining accuracy. The analysis
shows that hole-dilation and hole-taper ratio are increased with the
increasing of peak current and pulse on time. However, the surface
quality deteriorates as the peak current and pulse on time increase.
The combination that gives the optimum result for hole dilation is
medium peak current and short pulse on time. Meanwhile, the
optimum result for hole taper ratio is low peak current and short pulse
on time.
Abstract: A Disaster Management System (DMS) is very important for countries with multiple disasters, such as Chile. In the world (also in Chile)different disasters (earthquakes, tsunamis, volcanic eruption, fire or other natural or man-made disasters) happen and have an effect on the population. It is also possible that two or more disasters occur at the same time. This meansthata multi-risk situation must be mastered. To handle such a situation a Decision Support System (DSS) based on multiagents is a suitable architecture. The most known DMSs are concernedwith only a singledisaster (sometimes thecombination of earthquake and tsunami) and often with a particular disaster. Nevertheless, a DSS helps for a better real-time response. Analyze the existing systems in the literature and expand them for multi-risk disasters to construct a well-organized system is the proposal of our work. The here shown work is an approach of a multi-risk system, which needs an architecture and well defined aims. In this moment our study is a kind of case study to analyze the way we have to follow to create our proposed system in the future.
Abstract: The concept of technology as well as itself has
evolved continuously over time, such that, nowadays, this concept is
still marked by myths and realities. Even the concept of science is
frequently misunderstood as technology. In this way, this paper
presents different forms of interpretation of the concept of technology
in the course of history, as well as the social and cultural aspects
associated with it, through an analysis made by means of insights
from sociological studies of science and technology and its multiple
relations with society. Through the analysis of contents, the paper
presents a classification of how technology is interpreted in the social
sphere and search channel efforts to show how a broader
understanding can contribute to better interpretations of how
scientific and technological development influences the environment
in which we operate. The text also presents a particular point of view
for the interpretation of the concept from the analysis throughout the
whole work.
Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: The borate glasses are known by their structural
characterized by existence of unit’s structural composed by triangles
and tetrahedrons boron in different configurations depending on the
percentage of B2O3 in the glass chemical composition. In this paper,
effect of lithium oxide addition on the thermal and physical
properties of an alumina borate glass, was investigated. It was found
that the boron abnormality has a significant effect in the change of
glass properties according to the addition rate of lithium oxide.
Abstract: Various personality profile tests are used to identify
personality strengths and limits in individuals, helping both
individuals and managers to optimize work and team effort in
organizations. One such test, the Hartman’s personality profile,
emphasizes four driving "core motives" influenced or affected by
both strengths and limitations classified into four colors: Red -
motivated by power; Blue - discipline and loyalty; White - peace; and
Yellow – fun loving. Two shortcomings of Hartman’s personality test
are noted; 1) only one selection for every item / situation allowed and
2) selection of an item / option even if not applicable. A test taker
may be as much nurturing as he is opinionated but since
“opinionated” seems less attractive the individual would likely select
nurturing, causing a misidentification in personality strengths and
limits. Since few individuals have a “strong” personality, it is
difficult to assess their true personality strengths and limits allowing
only one choice or requiring unwanted choices, undermining the
potential of the test. We modified Hartman’s personality profile
allowing test takers to make either multiple choices for any item /
situation or leave them blank if applicable. Sixty-eight participants
(38 males and 30 females), 17 - 49 years old, from countries in Asia,
Europe, N. America, CIS, Africa, Latin America, and Oceania were
included. 58 participants (85.3%) reported the modified test, allowing
multiple / no choices better identified their personality strengths and
limits, while 10 participants (14.7%) expressed the original (one
choice version) was sufficient. The overall results show that our
modified test enhanced the identification and balance of core
personalities’ strengths and limits, aiding test takers, managers and
organizations to better assess individual characteristics, particularly
useful in making task-related, teamwork, and management decisions.
Abstract: The objective of this study was to identify the optimal
level of partial replacement of Portland cement by the ashes
originating from burning straw and bagasse from sugar cane (ASB).
Order to this end, were made five series of flat plates and cylindrical
bodies: control and others with the partial replacement in 20, 30, 40
and 50% of ASB in relation to the mass of the Ordinary Portland
cement, and conducted a mechanical testing of simple axial
compression (cylindrical bodies) and the four-point bending (flat
plates) and determined water absorption (WA), bulk density (BD)
and apparent void volume (AVV) on both types of specimens. Based
on the data obtained, it may be noted that the control treatment
containing only Portland cement, obtained the best results. However,
the cylindrical bodies with 20% ashes showed better results
compared to the other treatments. And in the formulations plates, the
treatment which showed the best results was 30% cement
replacement by ashes.
Abstract: The concentration levels of six heavy metals (Cd, Cr,
Fe, Ni, Pb and Zn) and two mineral elements (Ca and Mg) were
determined in soil samples collected from the vicinity of two auto
mechanic workshops in Sabon-Gari, Kaduna state, Nigeria, using
Atomic Absorption Spectrometry (AAS), in order to compare the
gradation of their concentrations with distance and depth of soil from
the workshop sites. At site 1, concentrations of Lead, Chromium, Iron
and Zinc were generally found to be above the World Health
Organization limits, while those of Nickel and Cadmium fell within
the limits. Iron had the highest concentration with a range of 176.274
ppm to 489.127 ppm at depths of 5 cm to 15 cm and a distance range
of 5 m to 15 m, while the concentration of cadmium was least with a
range of 0.001 ppm to 0.008 ppm at similar depth and distance
ranges. In addition, there was more of calcium (11.521 ppm to
121.709 ppm), in all the samples, than magnesium (11.293 ppm to
21.635 ppm). Similar results were obtained for site II. The
concentrations of all the metals analyzed showed a downward
gradient with increase in depth and distance from both workshop sites
except for iron and zinc at site 2. The immediate and remote
implications of these findings on the biota are discussed.
Abstract: The main aim of this article is to present a balance of the decade of Polish air transport market in the European Union having taking into account selected entities of the aviation market. This article analyzes the functioning of the Polish air transport market after the Polish accession to the European Union. During the study two main areas were pointed: shipping activity and activity of the airports. The most important benefits of integration and the benefits of introducing of the open sky policy were indicated. The last part of the article presents the perspectives of development of air traffic.
Abstract: Urban areas have been expanded throughout the
globe. Monitoring and modelling urban growth have become a
necessity for a sustainable urban planning and decision making.
Urban prediction models are important tools for analyzing the causes
and consequences of urban land use dynamics. The objective of this
research paper is to analyze and model the urban change, which has
been occurred from 1990 to 2000 using CORINE land cover maps.
The model was developed using drivers of urban changes (such as
road distance, slope, etc.) under an Artificial Neural Network
modelling approach. Validation was achieved using a prediction map
for 2006 which was compared with a real map of Urban Atlas of
2006. The accuracy produced a Kappa index of agreement of 0,639
and a value of Cramer's V of 0,648. These encouraging results
indicate the importance of the developed urban growth prediction
model which using a set of available common biophysical drivers
could serve as a management tool for the assessment of urban
change.
Abstract: The use of information tools is a common activity for
students of any educational stage when they encounter online
learning activities. Finding the relevant information for particular
learning tasks is the topic of this paper as it investigates the use of
information tools for a group of student participants. The paper
describes and discusses the results with particular implications for
use in higher education, and the findings suggest that improvement in
assessment design and subsequent student learning may be achieved
by structuring the purposefulness of information tools usage and
online reading behaviors of university students.
Abstract: The study of the electrical signals produced by neural
activities of human brain is called Electroencephalography. In this
paper, we propose an automatic and efficient EEG signal
classification approach. The proposed approach is used to classify the
EEG signal into two classes: epileptic seizure or not. In the proposed
approach, we start with extracting the features by applying Discrete
Wavelet Transform (DWT) in order to decompose the EEG signals
into sub-bands. These features, extracted from details and
approximation coefficients of DWT sub-bands, are used as input to
Principal Component Analysis (PCA). The classification is based on
reducing the feature dimension using PCA and deriving the supportvectors
using Support Vector Machine (SVM). The experimental are
performed on real and standard dataset. A very high level of
classification accuracy is obtained in the result of classification.
Abstract: This study was carried out to evaluate the nutritional
composition of the African River Prawn (Macrobrachium
vollenhovenii) in relation to Chokor (traditional) and Altona
(improved traditional) drying techniques used in the preservation and
processing of prawns by carrying out proximate composition
analysis. The value obtained for the proximate analysis of Chokor
and Altona smoke dried prawns were; Moisture (14.90% and
15.15%), Dry matter (85.10% and 84.85%), Protein (55.80% and
58.87%), Crude fat (1.95% and 1.98%), Crude fibre (21.40% and
13.11%), Carbohydrate (0.54% and 0.54%) and Ash (19.76% and
15.86%) respectively. The proximate mineral composition of Chokor
and Altona smoke dried prawns were; Calcium (5.66% and 4.20%)
and Phosphorus (9. 22% and 6.34%) respectively. Result shows there
was no loss of nutritional value with respect to Chokor and Altona
drying techniques used in the processing of prawns.
Abstract: In this paper, the improvement by deconvolution of
the depth resolution in Secondary Ion Mass Spectrometry (SIMS)
analysis is considered. Indeed, we have developed a new Tikhonov-
Miller deconvolution algorithm where a priori model of the solution
is included. This is a denoisy and pre-deconvoluted signal obtained
from: firstly, by the application of wavelet shrinkage algorithm,
secondly by the introduction of the obtained denoisy signal in an
iterative deconvolution algorithm. In particular, we have focused the
light on the effect of the iterations number on the evolution of the
deconvoluted signals. The SIMS profiles are multilayers of Boron in
Silicon matrix.
Abstract: The present paper summarizes the analysis of the
request for consultation of information and data on industrial
emissions made publicly available on the web site of the Ministry of
Environment, Land and Sea on integrated pollution prevention and
control from large industrial installations, the so called “AIA Portal”.
As a matter of fact, a huge amount of information on national
industrial plants is already available on internet, although it is usually
proposed as textual documentation or images.
Thus, it is not possible to access all the relevant information
through interoperability systems and also to retrieval relevant
information for decision making purposes as well as rising of
awareness on environmental issue.
Moreover, since in Italy the number of institutional and private
subjects involved in the management of the public information on
industrial emissions is substantial, the access to the information is
provided on internet web sites according to different criteria; thus, at
present it is not structurally homogeneous and comparable.
To overcome the mentioned difficulties in the case of the
Coordinating Committee for the implementation of the Agreement
for the industrial area in Taranto and Statte, operating before the
IPPC permit granting procedures of the relevant installation located
in the area, a big effort was devoted to elaborate and to validate data
and information on characterization of soil, ground water aquifer and
coastal sea at disposal of different subjects to derive a global
perspective for decision making purposes. Thus, the present paper
also focuses on main outcomes matured during such experience.
Abstract: A parametric study on circular thin-walled pipes
subjected to pure bending is performed. Both straight and curved
pipes are considered. Ratio D/t, initial pipe curvature and internal
pressure are the parameters varying in the analyses. The study is
mainly FEA-based.
It is found that negative curvatures (opposite to bending moment)
considerably increase stiffness and buckling limit of the pipe when no
internal pressure is acting and, similarly, positive curvatures decrease
the stiffness and buckling limit. For internal pressurised pipes the
effects of initial pipe curvature are less relevant. Results show that
this phenomenon is in relationship with the cross-section deformation
due to bending moment, which undergoes relevant ovalisation for no
pressurised pipes and little ovalisation for pressurised pipes.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.
Abstract: Solenoid operated electromagnetic control valve
(ECV) playing an important role for car’s air conditioning control
system. ECV is used in external variable displacement swash plate
type compressor and controls the entire air conditioning system by
means of a pulse width modulation (PWM) input signal supplying
from an external source (controller). Complete form of ECV contains
number of internal features like valve body, core, valve guide,
plunger, guide pin, plunger spring, bellows etc. While designing the
ECV; dimensions of different internal items must meet the standard
requirements as it is quite challenging. In this research paper,
especially the dimensioning of ECV body and its three pressure ports
through which the air/refrigerant passes are considered. Here internal
leakage test analysis of ECV body is being carried out from its
discharge port (Pd) to crankcase port (Pc) when the guide valve is
placed inside it. The experiments have made both in ordinary and
digital system using different assumptions and thereafter compare the
results.