Abstract: Corrugated wire mesh laminates (CWML) are a class
of engineered open cell structures that have potential for applications
in many areas including aerospace and biomedical engineering. Two
different methods of fabricating corrugated wire mesh laminates from
stainless steel, one using a high temperature Lithobraze alloy and the
other using a low temperature Eutectic solder for joining the
corrugated wire meshes are described herein. Their implementation is
demonstrated by manufacturing CWML samples of 304 and 316
stainless steel (SST). It is seen that due to the facility of employing
wire meshes of different densities and wire diameters, it is possible to
create CWML laminates with a wide range of effective densities. The
fabricated laminates are tested under uniaxial compression. The
variation of the compressive yield strength with relative density of the
CWML is compared to the theory developed by Gibson and Ashby for
open cell structures [22]. It is shown that the compressive strength of
the corrugated wire mesh laminates can be described using the same
equations by using an appropriate value for the linear coefficient in the
Gibson-Ashby model.
Abstract: In 2011, Debiao et al. pointed out that S-3PAKE protocol proposed by Lu and Cao for password-authenticated key exchange in the three-party setting is vulnerable to an off-line dictionary attack. Then, they proposed some countermeasures to eliminate the security vulnerability of the S-3PAKE. Nevertheless, this paper points out their enhanced S-3PAKE protocol is still vulnerable to undetectable on-line dictionary attacks unlike their claim.
Abstract: With a development of Hybrid Electric Vehicle(HEV),
A photovoltaic(PV) generation system is used for charging batteries in many cases. A dc/dc converter using PV power for a battery charger
requires a high efficiency. In this paper, A ZVS boost converter using the renewable energies for HEV charger is proposed. Through the theoretical analysis and experimental result, operation modes and characteristics of the proposed topology are verified.
Abstract: Noise causes significant sensibility changes on a human. This study investigated the effect of five different noises on electroencephalogram (EEG) and subjective evaluation. Six human subjects were exposed to classic piano, ocean wave, alarm in army, ambulance, mosquito noise and EEG data were collected during the experimental session. Alpha band activity in the mosquito noise was smaller than that in the classic piano. Alpha band activity decreased 43.4 ± 8.2 % in the mosquito noise. On the other hand, Beta band activity in the mosquito noise was greater than that in the classic piano. Beta band activity increased 60.1 ± 10.7 % in the mosquito noise. The advances from this study may aid the product design process with human sensibility engineering. This result may provide useful information in designing a human-oriented product to avoid the stress.
Abstract: The neural stimulation has been gaining much interest in neuromodulation research and clinical trials. For efficiency, there is a need for variable electrical stimulation such as current and voltage stimuli as well as wireless framework. In this regard, we develop the wireless neural stimulator capable of voltage and current stimuli. The system consists of ZigBee which is a wireless communication module and stimulus generator. The stimulus generator with 8-bits resolution enable both mono-polar and bi-polar waveform in voltage (-3.3~3.3V) and current(-330~330µA) stimulus mode which is controllable. The experimental results suggest that the proposed neural stimulator can play a role as an effective approach for neuromodulation.
Abstract: In this paper, we propose the low-MAC FEC controller for practical implementation of JPEG2000 image transmission using IEEE 802.15.4. The proposed low-MAC FEC controller has very small HW size and spends little computation to estimate channel state. Because of this advantage, it is acceptable to apply IEEE 802.15.4 which has to operate more than 1 year with battery. For the image transmission, we integrate the low-MAC FEC controller and RCPC coder in sensor node of LR-WPAN. The modified sensor node has increase of 3% hardware size than conventional zigbee sensor node.
Abstract: This paper presents a silicon controller rectifier (SCR)
based ESD protection circuit for IC. The proposed ESD protection
circuit has low trigger voltage and high holding voltage compared with
conventional SCR ESD protection circuit. Electrical characteristics of
the proposed ESD protection circuit are simulated and analyzed using
TCAD simulator. The proposed ESD protection circuit verified
effective low voltage ESD characteristics with low trigger voltage and
high holding voltage.
Abstract: This paper presents a synthetic jet air blower actuated
by PZT for air blowing for air-breathing micro PEM fuel cell. The
several factors to affect the performance of air-breathing PEM fuel cell
such as air flow rate, opening ratio and cathode open type in the
cathode side were studied. Especially, an air flow rate is critical
condition to improve its performance. In this paper, we developed a
synthetic jet air blower to supply a high stoichiometric air flow. The
synthetic jet mechanism is a zero mass flux device that converts
electrical energy into the momentum. The synthetic jet actuation is
usually generated by a traditional PZT actuator, which consists of a
small cylindrical cavity, in/outlet channel and PZT diaphragms. The
flow rate of the fabricated synthetic jet air blower was 400cc/min at
550Hz and its power consumption was very low under 0.3W. The
proposed air-breathing PEM fuel cell which installed synthetic jet air
blower was higher performance and stability during continuous
operation than the air-breathing fuel cell without auxiliary device to
supply the air. The results showed that the maximum power density
was 188mW/cm2 at 400mA/cm2. This maximum power density and
durability were improved more than 40% and 20%, respectively.
Abstract: In this paper, several different types of natural gas liquefaction cycle. First, two processes are a cascade process with two staged compression were designed and simulated. These include Inter-cooler which is consisted to Propane, Ethylene and Methane cycle, and also, liquid-gas heat exchanger is applied to between of methane and ethylene cycles (process2) and between of ethylene and propane (process2). Also, these cycles are compared with two staged cascade process using only a Inter-cooler (process1). The COP of process2 and process3 showed about 13.99% and 6.95% higher than process1, respectively. Also, the yield efficiency of LNG improved comparing with process1 by 13.99% lower specific power. Additionally, C3MR process are simulated and compared with Process 2.
Abstract: Recently, much research has been conducted for
security for wireless sensor networks and ubiquitous computing.
Security issues such as authentication and data integrity are major
requirements to construct sensor network systems. Advanced
Encryption Standard (AES) is considered as one of candidate
algorithms for data encryption in wireless sensor networks. In this
paper, we will present the hardware architecture to implement low
power AES crypto module. Our low power AES crypto module has
optimized architecture of data encryption unit and key schedule unit
which could be applicable to wireless sensor networks. We also details
low power design methods used to design our low power AES crypto
module.
Abstract: The purpose of this paper primarily intends to develop GIS interface for estimating sequences of stream-flows at ungauged stations based on known flows at gauged stations. The integrated GIS interface is composed of three major steps. The first, precipitation characteristics using statistical analysis is the procedure for making multiple linear regression equation to get the long term mean daily flow at ungauged stations. The independent variables in regression equation are mean daily flow and drainage area. Traditionally, mean flow data are generated by using Thissen polygon method. However, method for obtaining mean flow data can be selected by user such as Kriging, IDW (Inverse Distance Weighted), Spline methods as well as other traditional methods. At the second, flow duration curve (FDC) is computing at unguaged station by FDCs in gauged stations. Finally, the mean annual daily flow is computed by spatial interpolation algorithm. The third step is to obtain watershed/topographic characteristics. They are the most important factors which govern stream-flows. In summary, the simulated daily flow time series are compared with observed times series. The results using integrated GIS interface are closely similar and are well fitted each other. Also, the relationship between the topographic/watershed characteristics and stream flow time series is highly correlated.
Abstract: In this paper, a strategy for long-span bridge disaster response was developed, divided into risk analysis, business impact analysis, and emergency response plan. At the risk analysis stage, the critical risk was estimated. The critical risk was “car accident."The critical process by critical-risk classification was assessed at the business impact analysis stage. The critical process was the task related to the road conditions and traffic safety. Based on the results of the precedent analysis, an emergency response plan was established. By making the order of the standard operating procedures clear, an effective plan for dealing with disaster was formulated. Finally, a prototype software was developed based on the research findings. This study laid the foundation of an information-technology-based disaster response guideline and is significant in that it computerized the disaster response plan to improve the plan-s accessibility.
Abstract: In this paper, we propose disease diagnosis hardware
architecture by using Hypernetworks technique. It can be used to
diagnose 3 different diseases (SPECT Heart, Leukemia, Prostate
cancer). Generally, the disparate diseases require specified diagnosis
hardware model for each disease. Using similarities of three diseases
diagnosis processor, we design diagnosis processor that can diagnose
three different diseases. Our proposed architecture that is combining
three processors to one processor can reduce hardware size without
decrease of the accuracy.
Abstract: We present a subband adaptive infinite-impulse response (IIR) filtering method, which is based on a polyphase decomposition of IIR filter. Motivated by the fact that the polyphase structure has benefits in terms of convergence rate and stability, we introduce the polyphase decomposition to subband IIR filtering, i.e., in each subband high order IIR filter is decomposed into polyphase IIR filters with lower order. Computer simulations demonstrate that the proposed method has improved convergence rate over conventional IIR filters.
Abstract: Assessment for image quality traditionally needs its
original image as a reference. The conventional method for assessment
like Mean Square Error (MSE) or Peak Signal to Noise Ratio (PSNR)
is invalid when there is no reference. In this paper, we present a new
No-Reference (NR) assessment of image quality using blur and noise.
The recent camera applications provide high quality images by help of
digital Image Signal Processor (ISP). Since the images taken by the
high performance of digital camera have few blocking and ringing
artifacts, we only focus on the blur and noise for predicting the
objective image quality. The experimental results show that the
proposed assessment method gives high correlation with subjective
Difference Mean Opinion Score (DMOS). Furthermore, the proposed
method provides very low computational load in spatial domain and
similar extraction of characteristics to human perceptional assessment.
Abstract: This paper suggests a calibration method to reduce
errors occurring due to mobile robot sliding during location estimation
using the Dead-reckoning. Due to sliding of the mobile robot caused
between its wheels and the road surface while on free run, location
estimation can be erroneous. Sliding especially occurs during
cornering of mobile robot. Therefore, in order to reduce these frequent
sliding errors in cornering, we calibrated the mobile robot-s heading
values using a vision camera and templates of the ceiling.
Abstract: In this paper, a novel corner detection method is
presented to stably extract geometrically important corners.
Intensity-based corner detectors such as the Harris corner can detect
corners in noisy environments but has inaccurate corner position and
misses the corners of obtuse angles. Edge-based corner detectors such
as Curvature Scale Space can detect structural corners but show
unstable corner detection due to incomplete edge detection in noisy
environments. The proposed image-based direct curvature estimation
can overcome limitations in both inaccurate structural corner detection
of the Harris corner detector (intensity-based) and the unstable corner
detection of Curvature Scale Space caused by incomplete edge
detection. Various experimental results validate the robustness of the
proposed method.
Abstract: To achieve accurate and precise results of finite
element analysis (FEA) of bones, it is important to represent the
load/boundary conditions as identical as possible to the human body
such as the bone properties, the type and force of the muscles, the
contact force of the joints, and the location of the muscle attachment.
In this study, the difference in the Von-Mises stress and the total
deformation was compared by classifying them into Case 1, which
shows the actual anatomical form of the muscle attached to the femur
when the same muscle force was applied, and Case 2, which gives a
simplified representation of the attached location. An inverse
dynamical musculoskeletal model was simulated using data from an
actual walking experiment to complement the accuracy of the
muscular force, the input value of FEA. The FEA method using the
results of the muscular force that were calculated through the
simulation showed that the maximum Von-Mises stress and the
maximum total deformation in Case 2 were underestimated by 8.42%
and 6.29%, respectively, compared to Case 1. The torsion energy and
bending moment at each location of the femur occurred via the stress
ingredient. Due to the geometrical/morphological feature of the femur
of having a long bone shape when the stress distribution is wide, as
shown in Case 1, a greater Von-Mises stress and total deformation are
expected from the sum of the stress ingredients. More accurate results
can be achieved only when the muscular strength and the attachment
location in the FEA of the bones and the attachment form are the same
as those in the actual anatomical condition under the various moving
conditions of the human body.
Abstract: The contact width is important design parameter for
optimizing the design of new metal gasket for asbestos substitution
gasket. The contact width is found have relationship with the helium
leak quantity. In the increasing of axial load value, the helium leak
quantity is decreasing and the contact width is increasing. This study
provides validity method using simulation analysis and the result is
compared to experimental using pressure sensitive paper. The results
denote similar trend data between simulation and experimental result.
Final evaluation is determined by helium leak quantity to check
leakage performance of gasket design. Considering the phenomena of
position change on the convex contact, it can be developed the
optimization of gasket design by increasing contact width.
Abstract: In this study, we consider a special situation that only a pair of hydrophone on a moving underwater vehicle is available to localize a fixed acoustic source of far distance. The trigonometry can be used in this situation by using two different DOA of different locations. Notice that the distance between the two locations should be measured. Therefore, we assume that the vehicle is sailing straightly and the moving distance for each unit time is measured continuously. However, the accuracy of the localization using the trigonometry is highly dependent to the accuracy of DOAs and measured moving distances. Therefore, we proposed another method based on the extended Kalman filter that gives more robust and accurate localization result.