Abstract: Currently there are many use of threaded reinforcing
bars in construction fields because those do not need additional screw
processing when connecting reinforcing bar by threaded coupler. In
this study, reinforced concrete bridge piers using threaded rebar
coupler system at the plastic hinge area were tested to evaluate seismic
performance. The test results showed that threads of the threaded rebar
coupler system could be loosened while under tension-compression
cyclic loading because tolerance and rib face angle of a threaded rebar
coupler system are greater than that of a conventional ribbed rebar
coupler system. As a result, cracks were concentrated just outside of
the mechanical coupler and stiffness of reinforced concrete bridge pier
decreased. Therefore, it is recommended that connection ratio of
mechanical couplers in one section shall be below 50% in order that
cracks are not concentrated just outside of the mechanical coupler.
Also, reduced stiffness of the specimen should be considered when
using the threaded rebar coupler system.
Abstract: It is necessary to predict a fatigue crack propagation
life for estimation of structural integrity. Because of an uncertainty
and a randomness of a structural behavior, it is also required to
analyze stochastic characteristics of the fatigue crack propagation life
at a specified fatigue crack size. The essential purpose of this study is to find the effect of load ratio
on probability distribution of the fatigue crack propagation life at a
specified grown crack size and to confirm the good probability
distribution in magnesium alloys under various fatigue load ratio
conditions. To investigate a stochastic crack growth behavior, fatigue
crack propagation experiments are performed in laboratory air under
several conditions of fatigue load ratio using AZ31. By Anderson-Darling test, a goodness-of-fit test for probability
distribution of the fatigue crack propagation life is performed. The
effect of load ratio on variability of fatigue crack propagation life is
also investigated.
Abstract: This study aims to evaluate the effective size, section
and structural characteristics of circular hollow steel (CHS) damper.
CHS damper is among steel dampers which are used widely for
seismic energy dissipation because they are easy to install, maintain
and are inexpensive. CHS damper dissipates seismic energy through
metallic deformation due to the geometrical elasticity of circular shape
and fatigue resistance around connection part. After calculating the
effective size, which is found to be height to diameter ratio of √3,
nonlinear FE analyses were carried out to evaluate the structural
characteristics and effective section (diameter-to-ratio).
Abstract: Cerebellar ataxia is a steadily progressive
neurodegenerative disease associated with loss of motor control,
leaving patients unable to walk, talk, or perform activities of daily
living. Direct motor instruction in cerebella ataxia patients has limited
effectiveness, presumably because an inappropriate closed-loop
cerebellar response to the inevitable observed error confounds motor
learning mechanisms. Could the use of EEG based BCI provide
advanced biofeedback to improve motor imagery and provide a
“backdoor” to improving motor performance in ataxia patients? In
order to determine the feasibility of using EEG-based BCI control in
this population, we compare the ability to modulate mu-band power
(8-12 Hz) by performing a cued motor imagery task in an ataxia
patient and healthy control.
Abstract: We present a refined multiscale Shannon entropy for
analyzing electroencephalogram (EEG), which reflects the underlying
dynamics of EEG over multiple scales. The rationale behind
this method is that neurological signals such as EEG possess
distinct dynamics over different spectral modes. To deal with the
nonlinear and nonstationary nature of EEG, the recently developed
empirical mode decomposition (EMD) is incorporated, allowing a
decomposition of EEG into its inherent spectral components, referred
to as intrinsic mode functions (IMFs). By calculating the Shannon
entropy of IMFs in a time-dependent manner and summing them over
adaptive multiple scales, it results in an adaptive subscale entropy
measure of EEG. Simulation and experimental results show that
the proposed entropy properly reveals the dynamical changes over
multiple scales.
Abstract: This work assesses the cortical and the sub-cortical
neural activity recorded from rodents using entropy and mutual
information based approaches to study how hypothermia affects neural
activity. By applying the multi-scale entropy and Shannon entropy, we
quantify the degree of the regularity embedded in the cortical and
sub-cortical neurons and characterize the dependency of entropy of
these regions on temperature. We study also the degree of the mutual
information on thalamocortical pathway depending on temperature.
The latter is most likely an indicator of coupling between these highly
connected structures in response to temperature manipulation leading
to arousal after global cerebral ischemia.
Abstract: This work proposes a data-driven multiscale based
quantitative measures to reveal the underlying complexity of
electroencephalogram (EEG), applying to a rodent model of
hypoxic-ischemic brain injury and recovery. Motivated by that real
EEG recording is nonlinear and non-stationary over different
frequencies or scales, there is a need of more suitable approach over
the conventional single scale based tools for analyzing the EEG data.
Here, we present a new framework of complexity measures
considering changing dynamics over multiple oscillatory scales. The
proposed multiscale complexity is obtained by calculating entropies of
the probability distributions of the intrinsic mode functions extracted
by the empirical mode decomposition (EMD) of EEG. To quantify
EEG recording of a rat model of hypoxic-ischemic brain injury
following cardiac arrest, the multiscale version of Tsallis entropy is
examined. To validate the proposed complexity measure, actual EEG
recordings from rats (n=9) experiencing 7 min cardiac arrest followed
by resuscitation were analyzed. Experimental results demonstrate that
the use of the multiscale Tsallis entropy leads to better discrimination
of the injury levels and improved correlations with the neurological
deficit evaluation after 72 hours after cardiac arrest, thus suggesting an
effective metric as a prognostic tool.
Abstract: This paper provides a quantitative measure of the
time-varying multiunit neuronal spiking activity using an entropy
based approach. To verify the status embedded in the neuronal activity
of a population of neurons, the discrete wavelet transform (DWT) is
used to isolate the inherent spiking activity of MUA. Due to the
de-correlating property of DWT, the spiking activity would be
preserved while reducing the non-spiking component. By evaluating
the entropy of the wavelet coefficients of the de-noised MUA, a
multiresolution Shannon entropy (MRSE) of the MUA signal is
developed. The proposed entropy was tested in the analysis of both
simulated noisy MUA and actual MUA recorded from cortex in rodent
model. Simulation and experimental results demonstrate that the
dynamics of a population can be quantified by using the proposed
entropy.
Abstract: The design philosophy of building structure has been
changing time to time. The reason for this is because of an increase of
human inertest, an improved building materials and technology that
will impact how we live, to speed up construction period and natural
effect which includes earthquake disasters and environmental effect.
One technique which takes in to account the above case is using a
prefabricable structural system. In which each and every structural
element is designed and prefabricated and assembled on a site so that
the construction speed is increased and the environmental impact is
also enhanced. This system has an immense advantage such as: reduce
construction cost, reusable, recyclable, speed up construction period
and less environmental effect. In this study, it is tried to present some
of the developed and evaluated structural elements of building
structures.
Abstract: The Markov decision process (MDP) based
methodology is implemented in order to establish the optimal
schedule which minimizes the cost. Formulation of MDP problem
is presented using the information about the current state of pipe,
improvement cost, failure cost and pipe deterioration model. The
objective function and detailed algorithm of dynamic programming
(DP) are modified due to the difficulty of implementing the
conventional DP approaches. The optimal schedule derived from
suggested model is compared to several policies via Monte
Carlo simulation. Validity of the solution and improvement in
computational time are proved.
Abstract: The composite pavement system considered in this
paper is composed of a functional surface layer, a fiber reinforced
asphalt middle layer and a fiber reinforced lean concrete base layer.
The mix design of the fiber reinforced lean concrete corresponds to the
mix composition of conventional lean concrete but reinforced by
fibers. The quasi-absence of research on the durability or long-term
performances (fatigue, creep, etc.) of such mix design stresses the
necessity to evaluate experimentally the long-term characteristics of
this layer composition. This study tests the creep characteristics as one
of the long-term characteristics of the fiber reinforced lean concrete
layer for composite pavement using a new creep device. The test
results reveal that the lean concrete mixed with fiber reinforcement
and fly ash develops smaller creep than the conventional lean
concrete. The results of the application of the CEB-FIP prediction
equation indicate that a modified creep prediction equation should be
developed to fit with the new mix design of the layer.
Abstract: From the past earthquake events, many people get hurt at the exit while they are trying to go out of the buildings because of the exit doors are unable to be opened. The door is not opened because it deviates from its the original position. The aim of this research is to develop and evaluate a new type safety door that keeps the door frame in its original position or keeps its edge angles perpendicular during and post-earthquake. The proposed door is composed of three components: outer frame joined to the wall, inner frame (door frame) and circular hollow section connected to the inner and outer frame which is used as seismic energy dissipating device.
Abstract: For cycling, the analysis of the pedal force is one of the
important factors in the study of exercise ability assessment and
overuse injuries. In past studies, a two-axis measurement sensor was
used at the sagittal plane to measure the force only in the anterior,
posterior, and vertical directions and to analyze the loss of force and
the injury on the frontal plane due to the forces in the right and left
directions. In this study, which is a basic study on diverse analyses of
the pedal force that consider the forces on the sagittal plane and the
frontal plane, a three-axis pedal force measurement sensor was
developed to measure the anterior-posterior (Fx), medio-lateral (Fz),
and vertical (Fy) forces. The sensor was fabricated with a size and
shape similar to those of the general flat pedal, and had a 550g weight
that allowed smooth pedaling. Its measurement range was ±1000 N for
Fx and Fz and ±2000 N for Fy, and its non-linearity, hysteresis, and
repeatability were approximately 0.5%. The data were sampled at
1000 Hz using a signal collector. To use the developed sensor, the
pedaling efficiency (index of efficiency, IE) and the range of left and
right (medio-lateral, ML) forces were measured with two seat heights
(low and high). The results of the measurement showed that the IE was
higher and the force range in the ML direction was lower with the high
position than with the low position. The developed measurement
sensor and its application results will be useful in understanding and
explaining the complicated pedaling technique, and will enable
diverse kinematic analyses of the pedal force on the sagittal plane and
the frontal plane.
Abstract: In this study, we propose a novel technique for acoustic
echo suppression (AES) during speech recognition under barge-in
conditions. Conventional AES methods based on spectral subtraction
apply fixed weights to the estimated echo path transfer function
(EPTF) at the current signal segment and to the EPTF estimated until
the previous time interval. However, the effects of echo path changes
should be considered for eliminating the undesired echoes. We
describe a new approach that adaptively updates weight parameters in
response to abrupt changes in the acoustic environment due to
background noises or double-talk. Furthermore, we devised a voice
activity detector and an initial time-delay estimator for barge-in speech
recognition in communication networks. The initial time delay is
estimated using log-spectral distance measure, as well as
cross-correlation coefficients. The experimental results show that the
developed techniques can be successfully applied in barge-in speech
recognition systems.
Abstract: It is difficult to study the effect of various variables on
cycle fitting through actual experiment. To overcome such difficulty,
the forward dynamics of a musculoskeletal model was applied to cycle
fitting in this study. The measured EMG data weres compared with the
muscle activities of the musculoskeletal model through forward
dynamics. EMG data were measured from five cyclists who do not
have musculoskeletal diseases during three minutes pedaling with a
constant load (150 W) and cadence (90 RPM). The muscles used for
the analysis were the Vastus Lateralis (VL), Tibialis Anterior (TA),
Bicep Femoris (BF), and Gastrocnemius Medial (GM). Person’s
correlation coefficients of the muscle activity patterns, the peak timing
of the maximum muscle activities, and the total muscle activities were
calculated and compared. BIKE3D model of AnyBody (Anybodytech,
Denmark) was used for the musculoskeletal model simulation. The
comparisons of the actual experiments with the simulation results
showed significant correlations in the muscle activity patterns (VL:
0.789, TA: 0.503, BF: 0.468, GM: 0.670). The peak timings of the
maximum muscle activities were distributed at particular phases. The
total muscle activities were compared with the normalized muscle
activities, and the comparison showed about 10% difference in the VL
(+10%), TA (+9.7%), and BF (+10%), excluding the GM (+29.4%).
Thus, it can be concluded that muscle activities of model &
experiment showed similar results. The results of this study indicated
that it was possible to apply the simulation of further improved
musculoskeletal model to cycle fitting.
Abstract: Modular structural systems are constructed using a
method that they are assembled with prefabricated unit modular
frames on-site. This provides a benefit that can significantly reduce
building construction time. The structural design is usually carried out
under the assumption that their load-carrying mechanism is similar to
that of traditional steel moment-resisting systems. However, both
systems are different in terms of beam-column connection details
which may strongly influence the lateral structural behavior. Specially,
the presence of access holes in a beam-column joint of a unit modular
frame could cause undesirable failure during strong earthquakes.
Therefore, this study carried out finite element analyses (FEMs) of
unit modular frames to investigate the cyclic behavior of beam-column
joints with the access holes. Analysis results show that the unit
modular frames present stable cyclic response with large deformation
capacities and their joints are classified into semi-rigid connections
even if there are access holes.
Abstract: A feeding experiment was conducted to determine the
optimum dietary protein and lipid levels for juvenile fancy carp. Eight
experimental diets were formulated to contain four protein levels (200,
300, 400 and 500 g kg-1) with two lipid levels (70 and 140 g kg-1).
Triplicate groups of fish (initial weight, 12.1±0.2 g fish-1) were
hand-fed the diets to apparent satiation for 8 weeks. Fish growth
performance, feed utilization and feed intake were significantly
(P0.05). Weight gain and feed efficiency ratio tended to
increase as dietary protein level increased up to 400 and 500 g kg-1,
respectively. Daily feed intake of fish decreased with increasing
dietary protein level and that of fish fed diet contained 500 g kg-1
protein was significantly lower than other fish groups. The protein
efficiency ratio of fish fed 400 and 500 g kg-1 protein was lower than
that of fish fed 200 and 300 g kg-1 protein. Moisture, crude protein and
crude lipid contents of muscle and liver were significantly affected by
dietary protein, but not by dietary lipid level (P>0.05). The increase in
dietary lipid level resulted in an increase in linoleic acid in liver and
muscle paralleled with a decrease in n-3 highly unsaturated fatty acids
content in muscle of fish. In considering these results, it was concluded
that the diet containing 400 g kg-1 protein with 70 g kg-1 lipid level is
optimal for growth and efficient feed utilization of juvenile fancy carp.
Abstract: Vacuum insulation panel (VIP) is a promising thermal
insulator for buildings, refrigerator, LNG carrier and so on. In general,
it has the thermal conductivity of 2~4 mW/m·K. However, this thermal
conductivity is that measured at the center of VIP. The total effective
thermal conductivity of VIP is larger than this value due to the edge
conduction through the envelope. In this paper, the edge conduction of
VIP is examined theoretically, numerically and experimentally. To
confirm the existence of the edge conduction, numerical analysis is
performed for simple two-dimensional VIP model and a theoretical
model is proposed to calculate the edge conductivity. Also, the edge
conductivity is measured using the vacuum guarded hot plate and the
experiment is validated against numerical analysis. The results show
that the edge conductivity is dependent on the width of panel and
thickness of Al-foil. To reduce the edge conduction, it is recommended
that the VIP should be made as big as possible or made of thin Al film
envelope.
Abstract: This study is purposed to develop an efficient fault
detection method for Global Navigation Satellite Systems (GNSS)
applications based on adaptive noise covariance estimation. Due to the
dependence on radio frequency signals, GNSS measurements are
dominated by systematic errors in receiver’s operating environment.
In the proposed method, the pseudorange and carrier-phase
measurement noise covariances are obtained at time propagations and
measurement updates in process of Carrier-Smoothed Code (CSC)
filtering, respectively. The test statistics for fault detection are
generated by the estimated measurement noise covariances. To
evaluate the fault detection capability, intentional faults were added to
the filed-collected measurements. The experiment result shows that
the proposed method is efficient in detecting unhealthy measurements
and improves GNSS positioning accuracy against fault occurrences.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.