Abstract: High strength concrete has been used in situations
where it may be exposed to elevated temperatures. Numerous authors
have shown the significant contribution of polypropylene fiber to the
spalling resistance of high strength concrete.
When cement-based composite that reinforced by polypropylene
fibers heated up to 170 °C, polypropylene fibers readily melt and
volatilize, creating additional porosity and small channels in to the
matrix that cause the poor structure and low strength.
This investigation develops on the mechanical properties of mortar
incorporating polypropylene fibers exposed to high temperature.
Also effects of different pozzolans on strength behaviour of samples
at elevated temperature have been studied.
To reach this purpose, the specimens were produced by partial
replacement of cement with finely ground glass, silica fume and rice
husk ash as high reactive pozzolans. The amount of this replacement
was 10% by weight of cement to find the effects of pozzolans as a
partial replacement of cement on the mechanical properties of
mortars. In this way, lots of mixtures with 0%, 0.5%, 1% and 1.5% of
polypropylene fibers were cast and tested for compressive and
flexural strength, accordance to ASTM standard. After that
specimens being heated to temperatures of 300, 600 °C, respectively,
the mechanical properties of heated samples were tested.
Mechanical tests showed significant reduction in compressive
strength which could be due to polypropylene fiber melting. Also
pozzolans improve the mechanical properties of sampels.
Abstract: Ultrastructure of duodenum mucosa of irradiated rat
was studied versus dose rate of irradiation following exposure to
gamma rays from 60-Cobalt source. The animals were whole body
irradiated at two dose rates (1 Gy.mn-1 and 1 Gy.h-1) and three total
doses (1, 2 or 4 Gy) for each dose rate. 24 or 48 h after irradiation,
their small intestine was removed and samples of duodenum were
processed for observations under a transmission electron microscopy.
Samples of duodenum mucosa of control rats were processed in the
same way. For the lower dose rate of 1 Gy.h-1, main lesions
characteristic of apoptosis were detected within irradiated enterocytes
at a total dose of 2 Gy and 24 h after exposure. Necrosis was noted in
the samples, 48 h after exposition. For the higher dose rate of 1
Gy.mn-1, fewer changes were detected at all total doses 24 or 48 h
irradiation. Thus, it was shown that the appearance of radiationinduced
alterations varies not only with increasing total dose and
post-irradiation time but especially with decreasing dose rate.
Abstract: This paper describes a new approach of classification
using genetic programming. The proposed technique consists of
genetically coevolving a population of non-linear transformations on
the input data to be classified, and map them to a new space with a
reduced dimension, in order to get a maximum inter-classes
discrimination. The classification of new samples is then performed
on the transformed data, and so become much easier. Contrary to the
existing GP-classification techniques, the proposed one use a
dynamic repartition of the transformed data in separated intervals, the
efficacy of a given intervals repartition is handled by the fitness
criterion, with a maximum classes discrimination. Experiments were
first performed using the Fisher-s Iris dataset, and then, the KDD-99
Cup dataset was used to study the intrusion detection and
classification problem. Obtained results demonstrate that the
proposed genetic approach outperform the existing GP-classification
methods [1],[2] and [3], and give a very accepted results compared to
other existing techniques proposed in [4],[5],[6],[7] and [8].
Abstract: Application of pesticides in the paddy fields has
deleterious effects on non-target organisms including cyanobacteria
which are photosynthesizing and nitrogen fixing micro-organisms
contributing significantly towards soil fertility and crop yield.
Pesticide contamination in the paddy fields has manifested into a
serious global environmental concern. To study the effect of one such
pesticide, three cyanobacterial strains; Anabaena fertilissima,
Aulosira fertilissima and Westiellopsis prolifica were selected for
their stress responses to an Organochlorine insecticide - 6, 7, 8, 9, 10,
10-hexachloro-1, 5, 5a, 6, 9, 9a-hexahydro-6, 9-methano-2, 4, 3-
benzodioxathiepine-3-oxide, with reference to their photosynthesic
pigments-chlorophyll-a and carotenoids as well as accessory
pigments-phycobiliproteins (phycocyanin, allophycocyanin and
phycoerythrin), stress induced biochemical metabolites like
carbohydrates, proteins, amino acids, phenols and enzymes-nitrate
reductase, glutamine synthetase and succinate dehydrogenase. All
the three cyanobacterial strains were adversely affected by the
insecticide doses and inhibition was dose dependent. Reduction in
photosynthetic and accessory pigments, metabolites, nitrogen fixing
and respiratory enzymes of the test organisms were accompanied
with an initial increase in their total protein at lower Organochlorine
doses. On the other hand, increased amount of phenols in all the
insecticide treated concentrations was indicative of stressed activities
of the organisms.
Abstract: The Želazny Most tailing pond is one of the largest
facilities worldwide for waste disposal from the copper mines located
in South-West Poland. A potential failure of the dam would allow
more than 10 million cubic meters of contaminated slurry to flow to
the valley, causing immense environmental problems to the
surrounding area. Thus, the determination of the strength properties
of the dam's soils and their variability is of utmost importance.
An extensive site investigation consisting of more than 480 cone
penetration tests (CPTs) with or without pore water pressure
measurements were conducted within a period of 13 years to study
the mechanical properties of the tailings body. The present work
investigates the point variability of the soil strength parameters
(effective friction angle
Abstract: Nowadays, one of the most important problems of the
metropolises and the world large cities is the habitant traffic difficulty
and lack of sufficient parking site for the vehicles. Esfahan city as the
third metropolis of Iran has encountered with the vehicles parkingplace
problems in the most parts of fourteen regions of the city. The
non principled and non systematic dispersal and lack of parking sites
in the city has created an unfavorable status for its traffic and has
caused the air and sound pollutions increase; in addition, it wastes the
most portions of the citizenship and travelers' charge and time in
urban pathways and disturbs their mental and psychical calmness,
thus leads to their intensive dissatisfaction. In this study, by the usage
of AHP model in GIS environment, the effective criteria in selecting
the public parking sites have been combined with each other, and the
results of the created layers overlapping represent the parking
utilitarian vastness and widths. The achieved results of this research
indicate the pretty appropriate public parking sites selection in region
number 3 of Esfahan; but inconsequential dispersal and lack of these
parking sites in this region have caused abundant transportation
problems in Esfahan city.
Abstract: This paper presents the optimal controller design of
the generator control unit in the aircraft power system. The adaptive
tabu search technique is applied to tune the controller parameters
until the best terminal output voltage of generator is achieved. The
output response from the system with the controllers designed by the
proposed technique is compared with those from the conventional
method. The transient simulations using the commercial software
package show that the controllers designed from the adaptive tabu
search algorithm can provide the better output performance compared
with the result from the classical method. The proposed design
technique is very flexible and useful for electrical aircraft engineers.
Abstract: An exploratory computational investigation using
RANS & URANS was carried out to understand the aerodynamics
around an isolatedsingle rotating wheel with decreasing ground
proximity. The wheel was initially modeled in free air conditions,
then with decreasing ground proximity and increased yaw angle with
rotational speeds. Three speeds of rotation were applied to the wheel
so that the effect of different angular velocities can be investigated. In
addition to rotation, three different yaw angles were applied to the
rotating wheel in order to understand how these two variables
combined affect the aerodynamic flow field around the wheel.
Abstract: Thrombosis can be life threatening, necessitating therefore its instant treatment. Hydergine, a nootropic agent is used as a cognition enhancer in stroke patients but relatively little is known about its anti-thrombolytic effect. To investigate this aspect, in vivo and ex vivo experiments were designed and conducted. Three groups of rats were injected 1.5mg, 3.0mg and 4.5mg hydergine intraperitonealy with and without prior exposure to fresh plasma. Positive and negative controls were run in parallel. Animals were sacrificed after 1.5hrs and BT, CT, PT, INR, APTT, plasma calcium levels were estimated. For ex vivo analyses, each 1ml blood aspirated was exposed to 0.1mg, 0.2mg, 0.3mg dose of hydergine with parallel controls. Parameters analyzed were as above. Statistical analysis was through one-way ANOVA. Dunken-s and Tukey-s tests provided intra-group variance. BT, CT, PT, INR and APTT increased while calcium levels dropped significantly (P
Abstract: In this paper, Fabless Prototyping Methodology is
introduced for the design and analysis of MEMS devices.
Conventionally Finite Element Analysis (FEA) is performed before
system level simulation. In our proposed methodology, system level
simulation is performed earlier than FEA as it is computationally less
extensive and low cost. System level simulations are based on
equivalent behavioral models of MEMS device. Electrostatic
actuation based MEMS Microgripper is chosen as case study to
implement this methodology. This paper addresses the behavioral
model development and simulation of actuator part of an
electrostatically actuated Microgripper. Simulation results show that
the actuator part of Microgripper works efficiently for a voltage range
of 0-45V with the corresponding jaw displacement of 0-4.5425μm.
With some minor changes in design, this range can be enhanced to
15μm at 85V.
Abstract: The present work deals with thermodynamic analysis
of cascade refrigeration system using ozone friendly refrigerants pair
R507A and R23. R507A is azeotropic mixture composed of HFC
refrigerants R125/R143a (50%/50% wt.). R23 is a single component
HFC refrigerant used as replacement to CFC refrigerant R13 in low
temperature applications. These refrigerants have zero ozone
depletion potential and are non-flammable and as R507A an
azeotropic mixture there is no problem of temperature glide. This
study thermodynamically analyzed R507A-R23 cascade refrigeration
system to optimize the design and operating parameters of the
system. The design and operating parameters include: Condensing,
evaporating, subcooling and superheating temperatures in the high
temperature circuit, temperature difference in the cascade heat
exchanger, Condensing, evaporating, subcooling and superheating
temperatures in the low temperature circuit.
Abstract: Considering the theory of attribute grammars, we use
logical formulas instead of traditional functional semantic rules.
Following the decoration of a derivation tree, a suitable algorithm
should maintain the consistency of the formulas together with the
evaluation of the attributes. This may be a Prolog-like resolution, but
this paper examines a somewhat different strategy, based on
production specialization, local consistency and propagation: given a
derivation tree, it is interactively decorated, i.e. incrementally
checked and evaluated. The non-directed dependencies are
dynamically directed during attribute evaluation.
Abstract: In this paper, a new Genetic Algorithm (GA) based
methodology is proposed to optimize the Degree of Hybridization
(DOH) in a passenger parallel hybrid car. At first step, target
parameters for the vehicle are decided and then using ADvanced
VehIcle SimulatOR (ADVISOR) software, the variation pattern of
these target parameters, across the different DOHs, is extracted. At
the next step, a suitable cost function is defined and is optimized
using GA. In this paper, also a new technique has been proposed for
deciding the number of battery modules for each DOH, which leads
to a great improvement in the vehicle performance. The proposed
methodology is so simple, fast and at the same time, so efficient.
Abstract: In textile industry, besides the conventional textile
products, technical textile goods, that have been brought external
functional properties into, are being developed for technical textile
industry. Especially these products produced with weaving
technology are widely preferred in areas such as sports, geology,
medical, automotive, construction and marine sectors. These textile
products are exposed to various stresses and large deformations under
typical conditions of use. At this point, sufficient and reliable data
could not be obtained with uniaxial tensile tests for determination of
the mechanical properties of such products due to mainly biaxial
stress state. Therefore, the most preferred method is a biaxial tensile
test method and analysis. These tests and analysis is applied to fabrics
with different functional features in order to establish the textile
material with several characteristics and mechanical properties of the
product. Planar biaxial tensile test, cylindrical inflation and bulge
tests are generally required to apply for textile products that are used
in automotive, sailing and sports areas and construction industry to
minimize accidents as long as their service life. Airbags, seat belts
and car tires in the automotive sector are also subject to the same
biaxial stress states, and can be characterized by same types of
experiments. In this study, in accordance with the research literature
related to the various biaxial test methods are compared. Results with
discussions are elaborated mainly focusing on the design of a biaxial
test apparatus to obtain applicable experimental data for developing a
finite element model. Sample experimental results on a prototype
system are expressed.
Abstract: This study attempts to investigate the relationship
between internal CSR practices and organizational commitment
based on the social exchange theory (SET). Specifically, we examine
the impact of five dimensions of internal CSR practices on
organizational commitment: health and safety, human rights, training
and education, work life balance and workplace diversity. The
proposed model was tested on a sample of 336 frontline employees
within the banking sector in Jordan. Results showed that all internal
CSR dimensions are significantly and positively related to affective
and normative commitment. In addition, the findings of this study
indicate that all internal CSR dimensions did not have a significant
relationship with continuance commitment. Limitations of the study,
directions for future research, and implications of the findings are
discussed.
Abstract: Friction Stir Welding (FSW) is a solid state welding
process invented and patented by The Welding Institute (TWI) in the
United Kingdom in 1991 for butt and lap welding of metals and plastics. This paper highlights the benefits of friction stir welding
process as an energy efficient and a green technology process in the
field of welding. Compared to the other conventional welding processes, its benefits, typical applications and its use in joining
similar and dissimilar materials are also presented.
Abstract: The purpose of this research study is to investigate the manner in which various loads affect the mechanical properties of the formed mild steel plates. The investigation focuses on examining the cross-sectional area of the metal plate at the centre of the formed mild steel plate. Six mild steel plates were deformed with different loads. The loads applied on the plates had a magnitude of 5 kg, 10 kg, 15 kg, 20 kg, 25 kg and 30 kg. The radius of the punching die was 120 mm and the loads were applied at room temperature. The investigations established that the applied load causes the Vickers microhardness at the cross-sectional area of the plate to increase due to strain hardening. Hence, the percentage increase of the hardness due to the load was found to be directly proportional to the increase in the load. Furthermore, the tensile test results for the parent material showed that the average Ultimate Tensile Strength (UTS) for the three samples was 308 MPa while the average Yield Strength and Percentage Elongation were 227 MPa and 38 % respectively. Similarly, the UTS of the formed components increased after the deformation of the plate, as such it can be concluded that the forming loads alter the mechanical properties of the materials by improving and strengthening the material properties.
Abstract: This paper discusses a qualitative simulator QRiOM
that uses Qualitative Reasoning (QR) technique, and a process-based
ontology to model, simulate and explain the behaviour of selected
organic reactions. Learning organic reactions requires the application
of domain knowledge at intuitive level, which is difficult to be
programmed using traditional approach. The main objective of
QRiOM is to help learners gain a better understanding of the
fundamental organic reaction concepts, and to improve their
conceptual comprehension on the subject by analyzing the multiple
forms of explanation generated by the software. This paper focuses
on the generation of explanation based on causal theories to explicate
various phenomena in the chemistry subject. QRiOM has been tested
with three classes problems related to organic chemistry, with
encouraging results. This paper also presents the results of
preliminary evaluation of QRiOM that reveal its explanation
capability and usefulness.
Abstract: This paper gives a study about forging solution to
deploy the fixed wireless access (FWA) in the band 3300-3400MHz
instead of 3400-3600MHz to eschew the harmful interference
between from the FWA towards fixed satellite services receiver
presented in this band. The impact of FWA services toward the FSS
and the boundaries of spectrum emission mask had been considered
to calculate the possible Guard band required in this case. In
addition, supplementary separation distance added to improve the
coexistence between the two adjacent bands. Simulation had been
done using Matlab software base on ITU models reliance on the most
popular specification used for the tropical weather countries. Review
the current problem of interference between two systems and some
mitigation techniques which adopted in Malaysia as a case study is a
part of this research.
Abstract: Chitosan is a biopolymer composed of glucosamine
and N-acetyl glucosamine. Solubility and viscosity pose problems in
some applications. These problems can be overcome with unique
modifications. In this study, firstly, chitosan was modified by caffeic
acid and thioglycolic acid, separately. Then, growing effects of these
modified polymers was observed in U937 cell line. Caffeic acid is a
phenolic compound and its modifications act carcinogenic inhibitors
in drugs. Thiolated chitosans are commonly being used for drugdelivery
systems in various routes, because of enhancing
mucoadhesiveness property. U937 cell line was used model cell for
leukaemia. Modifications were achieved by 1 – 15 % binding range.
Increasing binding ratios showed higher radical-scavenging activity
and reducing cell growth, in compared to native chitosan. Caffeic
acid modifications showed higher radical-scavenging activity than
thiolated chitosans at the same concentrations. Caffeic acid and
thioglycolic acid modifications inhibited growth of U937, effectively.