Abstract: Liquid-liquid extraction is a process using two immiscible
liquids to extract compounds from one phase without high
temperature requirement. Mostly, the technical implementation of
this process is carried out in mixer-settlers or extraction columns. In
real chemical processes, chemicals may have high viscosity and
contain impurities. These impurities may change the settling behavior
of the process without measurably changing the physical properties
of the phases. In the current study, the settling behavior and the affected
parameters in a high-viscosity system were observed. Batchsettling
experiments were performed to experimentally quantify the
settling behavior and the mixer-settler model of Henschke [1] was
used to evaluate the behavior of the toluene + water system. The
viscosity of the system was increased by adding polyethylene glycol
4000 to the aqueous phase. NaCl and Na2SO4 were used to study the
influence of electrolytes. The results from this study show that increasing
the viscosity of water has a higher influence on the settling
behavior in comparison to the effects of the electrolytes. It can be
seen from the experiments that at high salt concentrations, there was
no effect on the settling behavior.
Abstract: The compatibility of optical resonators with microfluidic systems may be relevant for chemical and biological applications. Here, a fluorescent-core microcavity (FCM) is investigated as a refractometric sensor for heavy oils. A high-index film of silicon quantum dots (QDs) was formed inside the capillary, supporting cylindrical fluorescence whispering gallery modes (WGMs). A set of standard refractive index oils was injected into a capillary, causing a shift of the WGM resonances toward longer wavelengths. A maximum sensitivity of 240 nm/RIU (refractive index unit) was found for a nominal oil index of 1.74. As well, a sensitivity of 22 nm/RIU was obtained for a lower index of 1.48, more typical of fuel hydrocarbons. Furthermore, the observed spectra and sensitivities were compared to theoretical predictions and reproduced via FDTD simulations, showing in general an excellent agreement. This work demonstrates the potential use of FCMs for oil sensing applications and the more generally for detecting liquid solutions with a high refractive index or high viscosity.
Abstract: Two Amphiphilic catalysts, iron (III) dodecylbenzene
sulfonate and nickel (II) dodecylbenzene sulfonate, were synthesized
and used in the catalytic aquathermolysis of heavy crude oil to reduce
its viscosity. The prepared catalysts exhibited good performance in
the aquathermolysis and the viscosity is reduced by ~ 78.9 % for
Egyptian heavy crude oil. The chemical and physical properties of
heavy oil both before and after reaction were investigated by FT-IR,
dynamic viscosity, molecular weight and SARA analysis. The results
indicated that the content of resin, asphaltene, average molecular
weight and sulfur content of heavy oil is reduced after the catalytic
aquathermolysis.
Abstract: Ion-acoustic solitary and shock waves in dense
quantum plasmas whose constituents are electrons, positrons, and
positive ions are investigated. We assume that ion velocity is weakly
relativistic and also the effects of kinematic viscosity among the
plasma constituents is considered. By using the reductive
perturbation method, the Korteweg–deVries–Burger (KdV-B)
equation is derived.
Abstract: The Navier Stokes Equations (NSE) for an incompressible fluid of variable viscosity in the presence of an unknown external force in Von-Mises system x,\ are transformed, and some new exact solutions for a class of flows characterized by equation y f x a\b for an arbitrary state equation are determined, where f x is a function, \ the stream function, a z 0 and b are the arbitrary constants. In three, out of four cases, the function f x is arbitrary, and the solutions are the solutions of the flow equations for all the flows characterized by the equationy f x a\b. Streamline patterns for some forms of f x in unbounded and bounded regions are given.
Abstract: The experiment was performed to study the
relationship between excreta viscosity and Nitrogen-corrected true
metabolisable energy quantities of soybean meals using conventional
addition method (CAM) in adult cockerels for 7 d: a 3-d preexperiment
and a 4-d experiment period. Results indicated that
differences between the excreta viscosity values were (P
Abstract: The aim of the present study was to evaluate the
mucoadhesion and the release of nicotinamide gel formulations using
in vitro methods. An agar plate technique was used to investigate the
adhesiveness of the gels whereas a diffusion apparatus was employed
to determine the release of nicotinamide from the gels. In this
respect, 10% w/w nicotinamide gels containing bioadhesive
polymers: Carbopol 934P (0.5-2% w/w), hydroxypropylmethyl
cellulose (HPMC) (4-10% w/w), sodium carboxymethyl cellulose
(SCMC) (4-6% w/w) and methylcellulose 4000 (MC) (3-5% w/w)
were prepared. The gel formulations had pH values in the range of
7.14 - 8.17, which were considered appropriate to oral mucosa
application. In general, the rank order of pH values appeared to be
SCMC > MC4000 > HPMC > Carbopol 934P. Types and
concentrations of polymers used somewhat affected the
adhesiveness. It was found that anionic polymers (Carbopol 934 and
SCMC) adhered more firmly to the agar plate than the neutral
polymers (HPMC and MC 4000). The formulation containing 0.5%
Carbopol 934P (F1) showed the highest release rate. With the
exception of the formulation F1, the neutral polymers tended to give
higher relate rates than the anionic polymers. For oral tissue
treatment, the optimum has to be balanced between the residence
time (adhesiveness) of the formulations and the release rate of the
drug. The formulations containing the anionic polymers: Carbopol
934P or SCMC possessed suitable physical properties (appearance,
pH and viscosity). In addition, for anionic polymer formulations,
justifiable mucoadhesive properties and reasonable release rates of
nicotinamide were achieved. Accordingly, these gel formulations
may be applied for the treatment of oral mucosal lesions.
Abstract: This paper presents and discusses the numerical simulations of transient laminar natural convection cooling of high Prandtl number fluids in cubical cavities, in which the six walls of the cavity are subjected to a step change in temperature. The effect of the fluid Prandtl number on the heat transfer coefficient is studied for three different fluids (Golden Syrup, Glycerin and Glycerin-water solution 50%). The simulations are performed at two different Rayleigh numbers (5·106 and 5·107) and six different Prandtl numbers (3 · 105 ≥Pr≥ 50). Heat conduction through the cavity glass walls is also considered. The propsed correlations of the averaged heat transfer coefficient (N u) showed that it is dependant on the initial Ra and almost independent on P r. The instantaneous flow patterns, temperature contours and time evolution of volume averaged temperature and heat transfer coefficient are presented and analyzed.
Abstract: In the present analysis an unsteady laminar
forced convection water boundary layer flow is considered.
The fluid properties such as viscosity and Prandtl number are
taken as variables such that those are inversely proportional to
temperature. By using quasi-linearization technique the nonlinear
coupled partial differential equations are linearized and
the numerical solutions are obtained by using implicit finite
difference scheme with the appropriate selection of step sizes.
Non-similar solutions have been obtained from the starting
point of the stream-wise coordinate to the point where skin
friction value vanishes. The effect non-uniform mass transfer
along the surface of the cylinder through slot is studied on the
skin friction and heat transfer coefficients.
Abstract: This paper presents the design, fabrication and
evaluation of magneto-rheological damper. Semi-active control
devices have received significant attention in recent years because
they offer the adaptability of active control devices without requiring
the associated large power sources. Magneto-Rheological (MR)
dampers are semi- active control devices that use MR fluids to
produce controllable dampers. They potentially offer highly reliable
operation and can be viewed as fail-safe in that they become passive
dampers if the control hardware malfunction. The advantage of MR
dampers over conventional dampers are that they are simple in
construction, compromise between high frequency isolation and
natural frequency isolation, they offer semi-active control, use very
little power, have very quick response, has few moving parts, have a
relax tolerances and direct interfacing with electronics. Magneto-
Rheological (MR) fluids are Controllable fluids belonging to the
class of active materials that have the unique ability to change
dynamic yield stress when acted upon by an electric or magnetic
field, while maintaining viscosity relatively constant. This property
can be utilized in MR damper where the damping force is changed by
changing the rheological properties of the fluid magnetically. MR
fluids have a dynamic yield stress over Electro-Rheological fluids
(ER) and a broader operational temperature range. The objective of
this papert was to study the application of an MR damper to vibration
control, design the vibration damper using MR fluids, test and
evaluate its performance. In this paper the Rheology and the theory
behind MR fluids and their use on vibration control were studied.
Then a MR vibration damper suitable for vehicle suspension was
designed and fabricated using the MR fluid. The MR damper was
tested using a dynamic test rig and the results were obtained in the
form of force vs velocity and the force vs displacement plots. The
results were encouraging and greatly inspire further research on the
topic.
Abstract: This paper presents a part of research on the
rheological properties of bitumen modified by thermoplastic namely
linear low density polyethylene (LLDPE), high density polyethylene
(HDPE) and polypropylene (PP) and its interaction with 80 pen base
bitumen. As it is known that the modification of bitumen by the use
of polymers enhances its performance characteristics but at the same
time significantly alters its rheological properties. The rheological
study of polymer modified bitumen (PMB) was made through
penetration, ring & ball softening point and viscosity test. The results
were then related to the changes in the rheological properties of
polymer modified bitumen. It was observed that thermoplastic
copolymer shows profound effect on penetration rather than
softening point. The viscoelastic behavior of polymer modified
bitumen depend on the concentration of polymer, mixing
temperature, mixing technique, solvating power of base bitumen and
molecular structure of polymer used. PP offer better blend in
comparison to HDPE and LLDPE. The viscosity of base bitumen was
also enhanced with the addition of polymer. The pseudoplastic
behavior was more prominent for HDPE and LLDPE than PP. Best
results were obtained when polymer concentration was kept below
3%
Abstract: The effect of porous medium on the capillary instability of a cylindrical interface in the presence of axial electric field has been investigated using viscous potential flow theory. In viscous potential flow, the viscous term in Navier-Stokes equation vanishes as
vorticity is zero but viscosity is not zero. Viscosity enters through normal stress balance in the viscous potential flow theory and tangential stresses are not considered. A dispersion relation that accounts for the growth of axisymmetric waves is derived and stability is discussed theoretically as well as numerically. Stability criterion is given by critical value of applied electric field as well as critical wave number. Various graphs have been drawn to show the effect of various physical parameters such as electric field, viscosity ratio, permittivity ratio on the stability of the system. It has been observed that the axial electric field and porous medium both have stabilizing effect on the stability of the system.
Abstract: Avalanche release of snow has been modeled in the present studies. Snow is assumed to be represented by semi-solid and the governing equations have been studied from the concept of continuum approach. The dynamical equations have been solved for two different zones [starting zone and track zone] by using appropriate initial and boundary conditions. Effect of density (ρ), Eddy viscosity (η), Slope angle (θ), Slab depth (R) on the flow parameters have been observed in the present studies. Numerical methods have been employed for computing the non linear differential equations. One of the most interesting and fundamental innovation in the present studies is getting initial condition for the computation of velocity by numerical approach. This information of the velocity has obtained through the concept of fracture mechanics applicable to snow. The results on the flow parameters have found to be in qualitative agreement with the published results.
Abstract: The paper presents an analytical solution for dispersion
of a solute in the peristaltic motion of a micropolar fluid in the
presence of magnetic field and both homogeneous and heterogeneous
chemical reactions. The average effective dispersion coefficient has
been found using Taylor-s limiting condition under long wavelength
approximation. The effects of various relevant parameters on the average
coefficient of dispersion have been studied. The average effective
dispersion coefficient increases with amplitude ratio, cross viscosity
coefficient and heterogeneous chemical reaction rate parameter. But it
decreases with magnetic field parameter and homogeneous chemical
reaction rate parameter. It can be noted that the presence of peristalsis
enhances dispersion of a solute.
Abstract: Raisin Concentrate (RC) are the most important
products obtained in the raisin processing industries. These RC
products are now used to make the syrups, drinks and confectionery
productions and introduced as natural substitute for sugar in food
applications. Iran is a one of the biggest raisin exporter in the world
but unfortunately despite a good raw material, no serious effort to
extract the RC has been taken in Iran. Therefore, in this paper, we
determined and analyzed affected parameters on extracting RC
process and then optimizing these parameters for design the
extracting RC process in two types of raisin (round and long)
produced in Khorasan region. Two levels of solvent (1:1 and 2:1),
three levels of extraction temperature (60°C, 70°C and 80°C), and
three levels of concentration temperature (50°C, 60°C and 70°C)
were the treatments. Finally physicochemical characteristics of the
obtained concentrate such as color, viscosity, percentage of reduction
sugar, acidity and the microbial tests (mould and yeast) were
counted. The analysis was performed on the basis of factorial in the
form of completely randomized design (CRD) and Duncan's multiple
range test (DMRT) was used for the comparison of the means.
Statistical analysis of results showed that optimal conditions for
production of concentrate is round raisins when the solvent ratio was
2:1 with extraction temperature of 60°C and then concentration
temperature of 50°C. Round raisin is cheaper than the long one, and
it is more economical to concentrate production. Furthermore, round
raisin has more aromas and the less color degree with increasing the
temperature of concentration and extraction. Finally, according to
mentioned factors the concentrate of round raisin is recommended.
Abstract: This paper presents a methodical approach for designing and optimizing process parameters in oil blending industries. Twenty seven replicated experiments were conducted for production of A-Z crown super oil (SAE20W/50) employing L9 orthogonal array to establish process response parameters. Power law model was fitted to experimental data and the obtained model was optimized applying the central composite design (CCD) of response surface methodology (RSM). Quadratic model was found to be significant for production of A-Z crown supper oil. The study recognized and specified four new lubricant formulations that conform to ISO oil standard in the course of analyzing the batch productions of A-Z crown supper oil as: L1: KV = 21.8293Cst, BS200 = 9430.00Litres, Ad102=11024.00Litres, PVI = 2520 Litres, L2: KV = 22.513Cst, BS200 = 12430.00 Litres, Ad102 = 11024.00 Litres, PVI = 2520 Litres, L3: KV = 22.1671Cst, BS200 = 9430.00 Litres, Ad102 = 10481.00 Litres, PVI= 2520 Litres, L4: KV = 22.8605Cst, BS200 = 12430.00 Litres, Ad102 = 10481.00 Litres, PVI = 2520 Litres. The analysis of variance showed that quadratic model is significant for kinematic viscosity production while the R-sq value statistic of 0.99936 showed that the variation of kinematic viscosity is due to its relationship with the control factors. This study therefore resulted to appropriate blending proportions of lubricants base oil and additives and recommends the optimal kinematic viscosity of A-Z crown super oil (SAE20W/50) to be 22.86Cst.
Abstract: Interaction effects of xanthan gum (XG), carboxymethyl
cellulose (CMC), and locust bean gum (LBG) on the flow properties
of oil-in-water emulsions were investigated by a mixture design
experiment. Blends of XG, CMC and LBG were prepared according
to an augmented simplex-centroid mixture design (10 points) and used
at 0.5% (wt/wt) in the emulsion formulations. An appropriate
mathematical model was fitted to express each response as a function
of the proportions of the blend components that are able to
empirically predict the response to any blend of combination of the
components. The synergistic interaction effect of the ternary
XG:CMC:LBG blends at approximately 33-67% XG levels was
shown to be much stronger than that of the binary XG:LBG blend at
50% XG level (p < 0.05). Nevertheless, an antagonistic interaction
effect became significant as CMC level in blends was more than 33%
(p < 0.05). Yield stress and apparent viscosity (at 10 s-1) responses
were successfully fitted with a special quartic model while flow
behaviour index and consistency coefficient were fitted with a full
quartic model (R2
adjusted ≥ 0.90). This study found that a mixture
design approach could serve as a valuable tool in better elucidating
and predicting the interaction effects beyond the conventional twocomponent
blends.
Abstract: A pressure-based implicit procedure to solve Navier-
Stokes equations on a nonorthogonal mesh with collocated finite
volume formulation is used to simulate flow around the smart and
conventional flaps of spoiler under the ground effect. Cantilever
beam with uniformly varying load with roller support at the free end
is considered for smart flaps. The boundedness criteria for this
procedure are determined from a Normalized Variable diagram
(NVD) scheme. The procedure incorporates es the k -ε eddyviscosity
turbulence model. The method is first validated against
experimental data. Then, the algorithm is applied for turbulent
aerodynamic flows around a spoiler section with smart and
conventional flaps for different attack angle, flap angle and ground
clearance where the results of two flaps are compared.
Abstract: Synthetic juice clarification was done through spiral
wound ultrafiltration (UF) membrane module. Synthetic juice was
clarified at two different operating conditions, such as, with and
without permeates recycle at turbulent flow regime. The performance
of spiral wound ultrafiltration membrane was analyzed during
clarification of synthetic juice. Synthetic juice was the mixture of
deionized water, sucrose and pectin molecule. The operating
conditions are: feed flowrate of 10 lpm, pressure drop of 413.7 kPa
and Reynolds no of 5000. Permeate sample was analyzed in terms of
volume reduction factor (VRF), viscosity (Pa.s), ⁰Brix, TDS (mg/l),
electrical conductivity (μS) and turbidity (NTU). It was observe that
the permeate flux declined with operating time for both conditions of
with and without permeate recycle due to increase of concentration
polarization and increase of gel layer on membrane surface. For
without permeate recycle, the membrane fouling rate was faster
compared to with permeate recycle. For without permeate recycle,
the VRF rose up to 5 and for with recycle permeate the VRF is 1.9.
The VRF is higher due to adsorption of solute (pectin) molecule on
membrane surface and resulting permeateflux declined with VRF.
With permeate recycle, quality was within acceptable limit. Fouled
membrane was cleaned by applying different processes (e.g.,
deionized water, SDS and EDTA solution). Membrane cleaning was
analyzed in terms of permeability recovery.
Abstract: The Euler-s equation of motion is extended to include
the viscosity stress tensor leading to the formulation of Navier–
Stokes type equation. The latter is linearized and applied to
investigate the rotational motion or vorticity in a viscous fluid.
Relations for the velocity of viscous waves and attenuation parameter
are obtained in terms of viscosity (μ) and the density (¤ü) of the fluid.
μ and ¤ü are measured experimentally as a function of temperature for
two different samples of light and heavy crude oil. These data
facilitated to determine the activation energy, velocity of viscous
wave and the attenuation parameter. Shear wave velocity in heavy oil
is found to be much larger than the light oil, whereas the attenuation
parameter in heavy oil is quite low in comparison to light one. The
activation energy of heavy oil is three times larger than light oil.