Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: Non-linear dynamic time history analysis is
considered as the most advanced and comprehensive analytical
method for evaluating the seismic response and performance of
multi-degree-of-freedom building structures under the influence of
earthquake ground motions. However, effective and accurate
application of the method requires the implementation of advanced
hysteretic constitutive models of the various structural components
including masonry infill panels. Sophisticated computational research
tools that incorporate realistic hysteresis models for non-linear
dynamic time-history analysis are not popular among the professional
engineers as they are not only difficult to access but also complex and
time-consuming to use. In addition, commercial computer programs
for structural analysis and design that are acceptable to practicing
engineers do not generally integrate advanced hysteretic models
which can accurately simulate the hysteresis behavior of structural
elements with a realistic representation of strength degradation,
stiffness deterioration, energy dissipation and ‘pinching’ under cyclic
load reversals in the inelastic range of behavior. In this scenario,
push-over or non-linear static analysis methods have gained
significant popularity, as they can be employed to assess the seismic
performance of building structures while avoiding the complexities
and difficulties associated with non-linear dynamic time-history
analysis. “Push-over” or non-linear static analysis offers a practical
and efficient alternative to non-linear dynamic time-history analysis
for rationally evaluating the seismic demands. The present paper is
based on the analytical investigation of the effect of distribution of
masonry infill panels over the elevation of planar masonry infilled
reinforced concrete [R/C] frames on the seismic demands using the
capacity spectrum procedures implementing nonlinear static analysis
[pushover analysis] in conjunction with the response spectrum
concept. An important objective of the present study is to numerically
evaluate the adequacy of the capacity spectrum method using
pushover analysis for performance based design of masonry infilled
R/C frames for near-field earthquake ground motions.
Abstract: The aim of this paper is to analyze the impact of
literature review software on researchers. The aim of this study was
achieved by analyzing models in terms of perceived usefulness,
perceived ease of use, and acceptance level. Collected data were
analyzed using WarpPLS 4.0 software. This study used two
theoretical frameworks, namely, Technology Acceptance Model and
the Training Needs Assessment Model. The study was experimental
and was conducted at a public university in South Africa. The results
of the study showed that acceptance level has a high impact on
research productivity followed by perceived usefulness and perceived
ease of use.
Abstract: Current study established for EEG signal analysis in
patients with language disorder. Language disorder can be defined as
meaningful delay in the use or understanding of spoken or written
language. The disorder can include the content or meaning of
language, its form, or its use. Here we applied Z-score, power
spectrum, and coherence methods to discriminate the language
disorder data from healthy ones. Power spectrum of each channel in
alpha, beta, gamma, delta, and theta frequency bands was measured.
In addition, intra hemispheric Z-score obtained by scoring algorithm.
Obtained results showed high Z-score and power spectrum in
posterior regions. Therefore, we can conclude that peoples with
language disorder have high brain activity in frontal region of brain
in comparison with healthy peoples. Results showed that high coherence correlates with irregularities
in the ERP and is often found during complex task, whereas low
coherence is often found in pathological conditions. The results of the
Z-score analysis of the brain dynamics showed higher Z-score peak
frequency in delta, theta and beta sub bands of Language Disorder
patients. In this analysis there were activity signs in both hemispheres
and the left-dominant hemisphere was more active than the right.
Abstract: Analyzing the relation networks between the hospital
buildings which have complex structure and distinctive spatial
relationships is quite difficult. The hospital buildings which require
specialty in spatial relationship solutions during design and selfinnovation
through the developing technology should survive and
keep giving service even after the disasters such as earthquakes. In
this study, a hospital building where the load-bearing system was
strengthened because of the insufficient earthquake performance and
the construction of an additional building was required to meet the
increasing need for space was discussed and a comparative spatial
evaluation of the hospital building was made with regard to its status
before the change and after the change. For this reason, spatial
organizations of the building before change and after the change were
analyzed by means of Space Syntax method and the effects of the
change on space organization parameters were searched by applying
an analytical procedure. Using Depthmap UCL software,
Connectivity, Visual Mean Depth, Beta and Visual Integration
analyses were conducted. Based on the data obtained after the
analyses, it was seen that the relationships between spaces of the
building increased after the change and the building has become more
explicit and understandable for the occupants. Furthermore, it was
determined according to findings of the analysis that the increase in
depth causes difficulty in perceiving the spaces and the changes
considering this problem generally ease spatial use.
Abstract: The objective of this paper is to analyze the role played by the institute of the public hearings in the Brazilian Supreme Court. The public hearings are regulated since 1999 by the Brazilian Laws nº 9.868, nº 9.882 and by the Intern Regiment of the Brazilian Supreme Court. According to this legislation, the public hearings are supposed to be called when a matter of circumstance of fact must be clarified, what can be done through the hearing of the testimonies of persons with expertise and authority in the theme related to the cause. This work aims to investigate what is the role played by the public hearings and by the experts in the Brazilian Supreme Court. The hypothesis of this research is that: (I) The public hearings in the Brazilian Supreme Court are used to uphold a rhetoric of a democratic legitimacy of the Court`s decisions; (II) The Legislative intentions have been distorted. To test this hypothesis, the adopted methodology involves an empirical study of the Brazilian jurisprudence. As a conclusion, it follows that the public hearings convened by the Brazilian Supreme Court do not correspond, in practice, to the role assigned to them by the Congress since they do not serve properly to epistemic interests. The public hearings not only do not legitimate democratically the decisions, but also, do not properly clarify technical issues.
Abstract: The end of the line controls of the finished products in
the automotive industry is important. The control that has been
conducted with the manual methods for the sliding doors tracks is not
sufficient and faulty products cannot be identified. As a result, the
customer has the faulty products. In the scope of this study, the
design criteria of the PLC integrated modular end of line control unit
has been examined, designed and manufactured to make the control
of the 10 different track profile to 2 different vehicles with an
objective to minimize the salvage costs by obtaining more sensitive,
certain and accurate measurement results. In the study that started
with literature and patent review, the design inputs have been
specified, the technical concept has been developed, computer
supported mechanic design, control system and automation design,
design review and design improvement have been made. Laser
analog sensors at high sensitivity, probes and modular blocks have
been used in the unit. The measurement has been conducted in the
system and it is observed that measurement results are more sensitive
than the previous methods that we use.
Abstract: This paper presents the interface ConductHome which
controls home automation systems with a Leap Motion using
“invariant gesture protocols”. This interface is meant to simplify the
interaction of the user with its environment. A hardware part allows
the Leap Motion to be carried around the house. A software part
interacts with the home automation box and displays the useful
information for the user. An objective of this work is the
development of a natural/invariant/simple gesture control interface to
help elder people/people with disabilities.
Abstract: This paper describes how to dimension the electric
components of a 48V hybrid system considering real customer use.
Furthermore, it provides information about savings in energy and
CO2 emissions by a customer-tailored 48V hybrid. Based on measured customer profiles, the electric units such as the
electric motor and the energy storage are dimensioned. Furthermore,
the CO2 reduction potential in real customer use is determined
compared to conventional vehicles. Finally, investigations are carried
out to specify the topology design and preliminary considerations in
order to hybridize a conventional vehicle with a 48V hybrid system.
The emission model results from an empiric approach also taking into
account the effects of engine dynamics on emissions. We analyzed
transient engine emissions during representative customer driving
profiles and created emission meta models. The investigation showed
a significant difference in emissions when simulating realistic
customer driving profiles using the created verified meta models
compared to static approaches which are commonly used for vehicle
simulation.
Abstract: Greenhouses offer us suitable conditions which can
be controlled easily for the growth of the plant and they are made by
using a covering material that allows the sun light entering into the
system. Covering material can be glass, fiber glass, plastic or another
transparent element. This study investigates the solar energy usability
rates and solar energy benefitting rates of a semi-spherical (modified
arch) type greenhouse system according to different orientations and
positions which exists under climatic conditions of Bayburt. In the
concept of this study it is tried to determine the best direction and
best sizes of a semi-spherical greenhouse to get best solar benefit
from the sun. To achieve this aim a modeling study is made by using
MATLAB. However, this modeling study is run for some determined
shapes and greenhouses it can be used for different shaped
greenhouses or buildings. The basic parameters are determined as
greenhouse azimuth angle, the rate of size of long edge to short and
seasonal solar energy gaining of greenhouse. The optimum azimuth
angles of 400, 300, 250, 200, 150, 100, 50 m2 modified arch
greenhouse are 90o, 90o, 35o, 35o, 34o, 33o and 22o while their
optimum k values (ratio of length to width) are 10, 10, 10, 10, 6, 4
and 4 respectively. Positioning the buildings in order to get more
solar heat energy in winter and less in summer brings out energy and
money savings and increases the comfort.
Abstract: To ensure targeting of apoferritin nanocarrier with
encapsulated doxorubicin drug, we used a peptide linker based on a
protein G with N-terminus affinity towards Fc region of antibodies.
To connect the peptide to the surface of apoferritin, the C-terminus of
peptide was made of cysteine with affinity to gold. The surface of
apoferritin with encapsulated doxorubicin (APODOX) was coated
either with gold nanoparticles (APODOX-Nano) or gold(III) chloride
hydrate reduced with sodium borohydride (APODOX-HAu). The
reduction with sodium borohydride caused a loss of doxorubicin
fluorescent properties and probably accompanied with the loss of its
biological activity. Fluorescent properties of APODOX-Nano were
similar to the unmodified APODOX; therefore it was more suited for
the intended use. To evaluate the specificity of apoferritin modified
with antibodies, ELISA-like method was used with the surface of
microtitration plate wells coated by the antigen (goat anti-human IgG
antibodies). To these wells, the nanocarrier was applied. APODOX
without the modification showed 5× lower affinity to the antigen than
APODOX-Nano modified gold and targeting antibodies (human IgG
antibodies).
Abstract: The development of adaptive user interfaces (UI)
presents for a long time an important research area in which
researcher attempt to call upon the full resources and skills of several
disciplines, The adaptive UI community holds a thorough knowledge
regarding the adaptation of UIs with users and with contexts of use.
Several solutions, models, formalisms, techniques and mechanisms
were proposed to develop adaptive UI. In this paper, we propose an
approach based on the fuzzy set theory for modeling the concept of
the appropriateness of different solutions of UI adaptation with
different situations for which interactive systems have to adapt their
UIs.
Abstract: Introduction: There are multiple social, individual and
cultural factors that influence an individual’s decision to adopt family
planning methods especially among non-users in patriarchal societies
like Pakistan. Non-users, if targeted efficiently, can contribute
significantly to country’s CPR. A research study showed that nonusers
if convinced to adopt lactational amenorrhea method can shift
to long term methods in future. Research shows that if non users are
targeted efficiently a 59% reduction in unintended pregnancies in
Saharan Africa and South-Central and South-East Asia is anticipated.
Methods: We did secondary data analysis on Pakistan
Demographic Heath Survey (2012-13) dataset. Use of contraception
(never-use/ever-use) was the outcome variable. At univariate level
Chi-square/Fisher Exact test was used to assess relationship of
baseline covariates with contraception use. Then variables to be
incorporated in the model were checked for multicollinearity,
confounding and interaction. Then binary logistic regression (with an
urban-rural stratification) was done to find relationship between
contraception use and baseline demographic and social variables.
Results: The multivariate analyses of the study showed that
younger women (≤ 29 years)were more prone to be never users as
compared to those who were >30 years and this trend was seen in
urban areas (AOR 1.92, CI 1.453-2.536) as well as rural areas (AOR
1.809, CI 1.421-2.303). While looking at regional variation, women
from urban Sindh (AOR 1.548, CI 1.142-2.099) and urban
Balochistan (AOR 2.403, CI 1.504-3.839) had more never users as
compared to other urban regions. Women in the rich wealth quintile
were more never users and this was seen both in urban and rural
localities (urban (AOR 1.106 CI .753-1.624); rural areas (AOR 1.162,
CI .887-1.524)) even though these were not statistically significant.
Women idealizing more children (>4) are more never users as
compared to those idealizing less children in both urban (AOR 1.854,
CI 1.275-2.697) and rural areas (AOR 2.101, CI 1.514-2.916).
Women who never lost a pregnancy were more inclined to be nonusers
in rural areas (AOR 1.394, CI 1.127-1.723) .Women familiar
with only traditional or no method had more never users in rural areas
(AOR 1.717, CI 1.127-1.723) but in urban areas it wasn’t significant.
Women unaware of Lady Health Worker’s presence in their area
were more never users especially in rural areas (AOR 1.276, CI
1.014-1.607). Women who did not visit any care provider were more
never users (urban (AOR 11.738, CI 9.112-15.121) rural areas (AOR
7.832, CI 6.243-9.826)).
Discussion/Conclusion: This study concluded that government,
policy makers and private sector family planning programs should
focus on the untapped pool of never users (younger women from underserved provinces, in higher wealth quintiles, who desire more
children.). We need to make sure to cover catchment areas where
there are less LHWs and less providers as ignorance to modern
methods and never been visited by an LHW are important
determinants of never use. This all is in sync with previous literate
from similar developing countries.
Abstract: The feedbacks obtained regarding the sense of
presence from pilot users operating a Mobile Robotic presence
(MRP) system to visit a simulated museum are reported in this paper.
The aim is to investigate how much the perception of system’s
usefulness and ease of use is affected by operators’ sense of social
telepresence (presence) in the remote location. Therefore, scenarios
of visiting a museum are simulated and the user operators are
supposed to perform some regular tasks inside the remote
environment including interaction with local users, navigation and
visiting the artworks. Participants were divided into two groups,
those who had previous experience of operation and interaction with
a MRP system and those who never had experience. Based on the
results, both groups provided different feedbacks. Moreover, there
was a significant association between user’s sense of presence and
their perception of system usefulness and ease of use.
Abstract: Soil quality monitoring is a science-based soil
management tool that assesses soil ecosystem health.
A soil monitoring program in Auckland, New Zealand’s largest
city extends from 1995 to the present. The objective of this study was
to firstly determine changes in soil parameters (basic soil properties
and heavy metals) that were assessed from rural land in 1995-2000
and repeated in 2008-2012. The second objective was to determine
differences in soil parameters across various land uses including
native bush, rural (horticulture, pasture and plantation forestry) and
urban land uses using soil data collected in more recent years (2009-
2013).
Across rural land, mean concentrations of Olsen P had
significantly increased in the second sampling period and was
identified as the indicator of most concern, followed by soil
macroporosity, particularly for horticultural and pastoral land. Mean
concentrations of Cd were also greatest for pastoral and horticultural
land and a positive correlation existed between these two parameters,
which highlights the importance of analysing basic soil parameters in
conjunction with heavy metals. In contrast, mean concentrations of
As, Cr, Pb, Ni and Zn were greatest for urban sites. Native bush sites
had the lowest concentrations of heavy metals and were used to
calculate a ‘pollution index’ (PI). The mean PI was classified as high
(PI > 3) for Cd and Ni and moderate for Pb, Zn, Cr, Cu, As and Hg,
indicating high levels of heavy metal pollution across both rural and
urban soils. From a land use perspective, the mean ‘integrated
pollution index’ was highest for urban sites at 2.9 followed by
pasture, horticulture and plantation forests at 2.7, 2.6 and 0.9,
respectively.
It is recommended that soil sampling continues over time because
a longer spanning record will allow further identification of where
soil problems exist and where resources need to be targeted in the
future. Findings from this study will also inform policy and science
direction in regional councils.
Abstract: Recently, the green architecture becomes a
significant way to a sustainable future. Green building designs
involve finding the balance between comfortable homebuilding and
sustainable environment. Moreover, the utilization of the new
technologies such as artificial intelligence techniques are used to
complement current practices in creating greener structures to keep
the built environment more sustainable. The most common objectives
in green buildings should be designed to minimize the overall impact
of the built environment that effect on ecosystems in general and in
particularly human health and natural environment. This will lead to
protecting occupant health, improving employee productivity,
reducing pollution and sustaining the environmental. In green
building design, multiple parameters which may be interrelated,
contradicting, vague and of qualitative/quantitative nature are
broaden to use. This paper presents a comprehensive critical state- ofart-
review of current practices based on fuzzy and its combination
techniques. Also, presented how green architecture/building can be
improved using the technologies that been used for analysis to seek
optimal green solutions strategies and models to assist in making the
best possible decision out of different alternatives.
Abstract: Data mining idea is mounting rapidly in admiration
and also in their popularity. The foremost aspire of data mining
method is to extract data from a huge data set into several forms that
could be comprehended for additional use. The data mining is a
technology that contains with rich potential resources which could be
supportive for industries and businesses that pay attention to collect
the necessary information of the data to discover their customer’s
performances. For extracting data there are several methods are
available such as Classification, Clustering, Association,
Discovering, and Visualization… etc., which has its individual and
diverse algorithms towards the effort to fit an appropriate model to
the data. STATISTICA mostly deals with excessive groups of data
that imposes vast rigorous computational constraints. These results
trials challenge cause the emergence of powerful STATISTICA Data
Mining technologies. In this survey an overview of the STATISTICA
software is illustrated along with their significant features.
Abstract: In Jordan having deficit atmospheric precipitation, an
increase in water demand occurs during summer months. Jordan can
be regarded with a relatively high potential for wastewater recycling
and reuse. The main purpose of this paper was to investigate the
removal of total suspended solids (TSS) and chemical oxygen
demand (COD) for olive mill wastewater (OMW) by
electrocoagulation (EC) process. In the combination of
electrocoagulation by using coupled iron–aluminum electrodes, the
optimum working pH was found to be around 6. Results indicated
that the electrocoagulation process allowed removal of TSS and COD
of about 82.5% and 47.5%, respectively at 45 mA/cm2 after 70
minutes by using coupled iron–aluminum electrodes. It was
demonstrated that the maximum TSS and COD removals were
obtained at some optimum experimental parameters for current
density, pH, and reaction time.
Abstract: The building sector is responsible, in many
industrialized countries, for about 40% of the total energy
requirements, so it seems necessary to devote some efforts in this
area in order to achieve a significant reduction of energy
consumption and of greenhouse gases emissions.
The paper presents a study aiming at providing a design
methodology able to identify the best configuration of the system
building/plant, from a technical, economic and environmentally point
of view.
Normally, the classical approach involves a building's energy
loads analysis under steady state conditions, and subsequent selection
of measures aimed at improving the energy performance, based on
previous experience made by architects and engineers in the design
team. Instead, the proposed approach uses a sequence of two wellknown
scientifically validated calculation methods (TRNSYS and
RETScreen), that allow quite a detailed feasibility analysis.
To assess the validity of the calculation model, an existing,
historical building in Central Italy, that will be the object of
restoration and preservative redevelopment, was selected as a casestudy.
The building is made of a basement and three floors, with a
total floor area of about 3,000 square meters.
The first step has been the determination of the heating and
cooling energy loads of the building in a dynamic regime by means,
which allows simulating the real energy needs of the building in
function of its use. Traditional methodologies, based as they are on
steady-state conditions, cannot faithfully reproduce the effects of
varying climatic conditions and of inertial properties of the structure.
With this model is possible to obtain quite accurate and reliable
results that allow identifying effective combinations building-HVAC
system.
The second step has consisted of using output data obtained as
input to the calculation model, which enables to compare different
system configurations from the energy, environmental and financial
point of view, with an analysis of investment, and operation and
maintenance costs, so allowing determining the economic benefit of
possible interventions.
The classical methodology often leads to the choice of
conventional plant systems, while our calculation model provides a
financial-economic assessment for innovative energy systems and
low environmental impact.
Computational analysis can help in the design phase, particularly
in the case of complex structures with centralized plant systems, by
comparing the data returned by the calculation model for different
design options.
Abstract: There has been a significant decline in active travel
and a massive increase in the use of car dependent travel in many
countries during the past two decades. Evidential risks for people’s
physical and mental health problems are correlated with this
increased use of motorized travel. These health related problems
range from overweight and obesity to increased air pollution. In
response to these rising concerns health professionals, traffic planers,
local authorities and others have introduced a variety of initiatives to
counterbalance the dominance of cars for daily journeys.
However, the nature of travel behavior change interventions,
which aim to reduce car use, are very complex and challenging
regarding their interactions with human behavior. To change travel
behavior at least two aspects have to be taken into consideration.
First, how to alter attitudes and perceptions toward the sustainable
and healthy modes of travel, in competition with experiences of
private car use. And second, how to make these behavior change
processes irreversible and sustainable. There are no comprehensive
models available to guide policy interventions to increase the level of
success of travel behavior change interventions across both these
dimensions.
A comprehensive theoretical framework is required in the effort to
optimize how to facilitate and guide the processes of data collection
and analysis to achieve the best possible guidelines for policy
makers. Regarding the gaps in the travel behavior change research
literature, this paper attempted to identify and suggest a
multidimensional framework in order to facilitate planning the
implemented travel behavior change interventions. A structured
mixed-method model is suggested to improve the analytic power of
the results according to the complexity of human behavior.
In order to recognize people’s attitudes towards a specific travel
mode, the Theory of Planned Behavior (TPB) was operationalized.
But in order to capture decision making processes the Transtheoretical
model of Behavior Change (TTM) was also used.
Consequently, the combination of these two theories (TTM and TPB)
has resulted in a synthesis with appropriate concepts to identify and
design an implemented travel behavior change interventions.