Abstract: Nonstandard tests are necessary for analyses and
verification of new developed structural and technological solutions
with application of composite materials. One of the most critical
primary structural parts of a typical aerospace structure is T-joint.
This structural element is loaded mainly in shear, bending, peel and
tension. The paper is focused on the shear loading simulations. The
aim of the work is to obtain a representative uniform distribution of
shear loads along T-joint during the mechanical testing. A new
design of T-joint test procedure, numerical simulation and
optimization of representative boundary conditions are presented.
The different conditions and inaccuracies both in simulations and
experiments are discussed. The influence of different parameters on
stress and strain distributions is demonstrated on T-joint made of
CFRP (carbon fibre reinforced plastic). A special test rig designed by
VZLU (Aerospace Research and Test Establishment) for T-shear test
procedure is presented.
Abstract: The high Peak to Average Power Ratio (PAR) in Filter
Bank Multicarrier with Offset Quadrature Amplitude Modulation
(FBMC-OQAM) can significantly reduce power efficiency and
performance. In this paper, we address the problem of PAPR
reduction for FBMC-OQAM systems using Tone Reservation (TR)
technique. Due to the overlapping structure of FBMCOQAM signals,
directly applying TR schemes of OFDM systems to FBMC-OQAM
systems is not effective. We improve the tone reservation (TR)
technique by employing sliding window with Active Constellation
Extension for the PAPR reduction of FBMC-OQAM signals, called
sliding window tone reservation Active Constellation Extension
(SW-TRACE) technique. The proposed SW-TRACE technique uses
the peak reduction tones (PRTs) of several consecutive data
blocks to cancel the peaks of the FBMC-OQAM signal inside a
window, with dynamically extending outer constellation points in
active(data-carrying) channels, within margin-preserving constraints,
in order to minimize the peak magnitude. Analysis and simulation
results compared to the existing Tone Reservation (TR) technique for
FBMC/OQAM system. The proposed method SW-TRACE has better
PAPR performance and lower computational complexity.
Abstract: The aesthetic qualities and the versatility of reinforced
concrete have made it a popular choice for many architects and
structural engineers. Therefore, the exploration of natural materials
such as gravels and sands as well as lime-stone for cement production
is increasing to produce a concrete material. The exploration must
affect to the environment. Therefore, the using of the concrete
materials should be as efficient as possible. According to its natural
behavior of the concrete material, it is strong in compression and weak
in tension. Therefore the contribution of the tensile stresses of the
concrete to the flexural capacity of the beams is neglected. However,
removing of concrete on tension zone affects to the decreasing of
flexural capacity. Introduce the strut action of truss structures may an
alternative to solve the decreasing of flexural capacity. A series of
specimens were prepared to clarify the effect of the truss structures in
the concrete beams without concrete on the tension zone. Results
indicated that the truss system is necessary for the external reinforced
concrete beams. The truss system of concrete beam without concrete
on tension zone (BR) could develop almost same capacity to the
normal beam (BN). It can be observed also that specimens BR has
lower number of cracks than specimen BN. This may be caused by the
fact that there was no bonding effect on the tensile reinforcement on
specimen BR to distribute the cracks.
Abstract: Crude oil is a major source of global energy. The major problem is its widespread use and demand resulted is in increasing environmental pollution. One associated pollution problem is ‘oil spills’. Oil spills can be remediated with the use of chemical dispersants, microbial biodegradation and microbial metabolites such as biosurfactants. Four different minimal salt media for biosurfactant production by Bacillus isolated from oil contaminated sites from Oman were screened. These minimal salt media were supplemented with either glucose or sucrose as a carbon source. Among the isolates, W16 and B30 produced the most active biosurfactants. Isolate W16 produced better biosurfactant than the rest, and reduced surface tension (ST) and interfacial tension (IFT) to 25.26mN/m and 2.29mN/m respectively within 48h which are characteristics for removal of oil in contaminated sites. Biosurfactant was produced in bulk and extracted using acid precipitation method. Thin Layer Chromatography (TLC) of acid precipitate biosurfactant revealed two concentrated bands. Further studies of W16 biosurfactant in bioremediation of oil spills are recommended.
Abstract: This investigation presents the formulation of kerf (width of slit) and optimal control parameter settings of wire electrochemical discharge machining which results minimum possible kerf while machining Al7075/SiCp MMCs. WEDM is proved its efficiency and effectiveness to cut the hard ceramic reinforced MMCs within the permissible budget. Among the distinct performance measures of WEDM process, kerf is an important performance characteristic which determines the dimensional accuracy of the machined component while producing high precision components. The lack of available of the machinability information such advanced MMCs result the more experimentation in the manufacturing industries. Therefore, extensive experimental investigations are essential to provide the database of effect of various control parameters on the kerf while machining such advanced MMCs in WEDM. Literature reviled the significance some of the electrical parameters which are prominent on kerf for machining distinct conventional materials. However, the significance of reinforced particulate size and volume fraction on kerf is highlighted in this work while machining MMCs along with the machining parameters of pulse-on time, pulse-off time and wire tension. Usually, the dimensional tolerances of machined components are decided at the design stage and a machinist pay attention to produce the required dimensional tolerances by setting appropriate machining control variables. However, it is highly difficult to determine the optimal machining settings for such advanced materials on the shop floor. Therefore, in the view of precision of cut, kerf (cutting width) is considered as the measure of performance for the model. It was found from the literature that, the machining conditions of higher fractions of large size SiCp resulting less kerf where as high values of pulse-on time result in a high kerf. A response surface model is used to predict the relative significance of various control variables on kerf. Consequently, a powerful artificial intelligence called genetic algorithms (GA) is used to determine the best combination of the control variable settings. In the next step the conformation test was conducted for the optimal parameter settings and found good agreement between the GA kerf and measured kerf. Hence, it is clearly reveal that the effectiveness and accuracy of the developed model and program to analyze the kerf and to determine its optimal process parameters. The results obtained in this work states that, the resulted optimized parameters are capable of machining the Al7075/SiCp MMCs more efficiently and with better dimensional accuracy.
Abstract: Essential hypertension (HTN) usually clusters with other cardiovascular risk factors such as age, overweight, diabetes, insulin resistance and dyslipidemia. The target organ damage (TOD) such as left ventricular hypertrophy, microalbuminuria (MA), acute coronary syndrome (ACS), stroke and cognitive dysfunction takes place early in course of hypertension. Though the prevalence of hypertension is high in India, the relationship between microalbuminuria and target organ damage in hypertension is not well studied. This study aim at detecting MA in essential hypertension and its relation to severity of HTN, duration of HTN, body mass index (BMI), age and TOD such as HTN retinopathy and acute coronary syndrome The present study was done in 100 patients of essential hypertension non diabetics admitted to B.L.D.E.University-s Sri B.M.Patil Medical College, Bijapur, from October 2008 to April 2011. The patients underwent detailed history and clinical examination. Early morning 5 ml of urine sample was collected & MA was estimated by immunoturbidometry method. The relationship of MA with the duration & severity of HTN, BMI, age, sex and TOD's like hypertensive retinopathy, ACS was assessed by univariate analysis. The prevalence of MA in this study was found to be 63 %. In that 42% were male & 21% were female. In this study a significant association between MA and the duration of hypertension (p = 0.036) & (OR =0.438). Longer the duration of hypertension, more possibility of microalbumin in urine. Also there was a significant association between severity of hypertension and MA (p=0.045) and (OR=0.093). MA was positive in 50 (79.4%) patients out of 63, whose blood pressure was >160/100 mm Hg. In this study a significant association between MA and the grades of hypertensive retinopathy (p =0.011) and acute coronary syndrome (p = 0.041) (OR =2.805). Gender and BMI did not pose high risk for MA in this study.The prevalence of MA in essential hypertension is high in this part of the community and MA will increase the risk of developing target organ damage.Early screening of patients with essential hypertension for MA and aggressive management of positive cases might reduce the burden of chronic kidney diseases and cardiovascular diseases in the community.
Abstract: Use of microemulsion in enhanced oil recovery has become more attractive in recent years because of its high level of extraction efficiency. Experimental investigations have been made on characterization of microemulsions of oil-brinesurfactant/ cosurfactant system for its use in enhanced oil recovery (EOR). Sodium dodecyl sulfate, propan-1-ol and heptane were selected as surfactant, cosurfactant and oil respectively for preparation of microemulsion. The effects of salinity on the relative phase volumes and solubilization parameters have also been studied. As salinity changes from low to high value, phase transition takes place from Winsor I to Winsor II via Winsor III. Suitable microemulsion composition has been selected based on its stability and ability to reduce interfacial tension. A series of flooding experiments have been performed using the selected microemulsion. The flooding experiments were performed in a core flooding apparatus using uniform sand pack. The core holder was tightly packed with uniform sands (60-100 mesh) and saturated with brines of different salinities. It was flooded with the brine at 25 psig and the absolute permeability was calculated from the flow rate of the through sand pack. The sand pack was then flooded with the crude oil at 800 psig to irreducible water saturation. The initial water saturation was determined on the basis of mass balance. Waterflooding was conducted by placing the coreholder horizontally at a constant injection pressure at 200 pisg. After water flooding, when water-cut reached above 95%, around 0.5 pore volume (PV) of the above microemulsion slug was injected followed by chasing water. The experiments were repeated using different composition of microemulsion slug. The additional recoveries were calculated by material balance. Encouraging results with additional recovery more than 20% of original oil in place above the conventional water flooding have been observed.
Abstract: Emphasis on the advancement of new materials and technology has been there for the past few decades. The global development towards using cheap and durable materials from renewable resources contributes to sustainable development. An experimental investigation of mechanical behaviour of sisal fibre-reinforced concrete is reported for making a suitable building material in terms of reinforcement. Fibre reinforced Composite is one such material, which has reformed the concept of high strength. Sisal fibres are abundantly available in the hot areas. Sisal fibre has emerged as a reinforcing material for concretes, used in civil structures. In this work, properties such as hardness and tensile strength of sisal fibre reinforced cement composites with 6, 12, 18 and 24% by weight of sisal fibres were assessed. Sisal fibre reinforced cement composite slabs with long sisal fibres were manufactured using a cast hand lay up technique. Mechanical response was measured under tension. The high energy absorption capacity of the developed composite system was reflected in high toughness values under tension respectively.
Abstract: The effect of a uniform magnetic field on the
formation of drops of specific size has been investigated numerically
in a T-shaped microchannel. Previous researches indicated that the
drop sizes of secondary stream decreases, with increasing main
stream flow rate and decreasing interfacial tension. In the present
study the effect of a uniform magnetic field on the main stream is
considered, and it is proposed that by increasing the Hartmann
number, the size of the drops of the secondary stream will be
decreased.
Abstract: In order to supplement the brittle property of concrete,
fibers are added into concrete mixtures. Compared to general concrete,
various characteristics such as tensile strength, bending strength,
bending toughness, and resistance to crack are superior, and even
when cracks occur, improvements on toughness as well as resistance
to shock are excellent due to the growth of fracture energy. Increased
function of steel fiber reinforced concrete can be differentiated
depending on the fiber dispersion, and sand percentage can be an
important influence on the fiber dispersion. Therefore, in this research,
experiments were planned on sand percentage in order to apprehend
the influence of sand percentage on the bending properties and direct
tension of SFRC and basic experiments were conducted on bending
and direct tension in order to recognize the properties of bending
properties and direct tension following the size of the aggregates and
sand percentage.
Abstract: Hypertension is characterized with stress on the heart and blood vessels thus increasing the risk of heart attack and renal diseases. The Renin angiotensin system (RAS) plays a major role in blood pressure control. Renin is the enzyme that controls the RAS at the rate-limiting step. Our aim is to develop new drug-like leads which can inhibit renin and thereby emerge as therapeutics for hypertension. To achieve this, molecular dynamics (MD) simulation and receptor-based pharmacophore modeling were implemented, and three rennin-inhibitor complex structures were selected based on IC50 value and scaffolds of inhibitors. Three pharmacophore models were generated considering conformations induced by inhibitor. The compounds mapped to these models were selected and subjected to drug-like screening. The identified hits were docked into the active site of renin. Finally, hit1 satisfying the binding mode and interaction energy was selected as possible lead candidate to be used in novel renin inhibitors.
Abstract: Cements, which are intrinsically brittle materials, can
exhibit a degree of pseudo-ductility when reinforced with a sufficient
volume fraction of a fibrous phase. This class of materials, called
Engineered Cement Composites (ECC) has the potential to be used in
future tunneling applications where a level of pseudo-ductility is
required to avoid brittle failures. However uncertainties remain
regarding mechanical performance. Previous work has focused on
comparatively thin specimens; however for future civil engineering
applications, it is imperative that the behavior in tension of thicker
specimens is understood. In the present work, specimens containing
cement powder and admixtures have been manufactured following
two different processes and tested in tension. Multiple matrix
cracking has been observed during tensile testing, leading to a
“strain-hardening" behavior, confirming the possible suitability of
ECC material when used as thick sections (greater than 50mm) in
tunneling applications.
Abstract: Pressure vessels are usually operating at temperatures
where the conditions of linear elastic fracture mechanics are no
longer met because massive plasticity precedes crack propagation. In
this work the development of a surface crack in a pressure vessel
subject to bending and tension under elastic-plastic fracture
mechanics conditions was investigated. Finite element analysis was
used to evaluate the hydrostatic stress, the J-integral and crack
growth for semi-elliptical surface-breaking cracks. The results
showed non-uniform stress triaxiality and crack driving force around
the crack front at large deformation levels. Different ductile crack
extensions were observed which emphasis the dependent of ductile
tearing on crack geometry and type of loading. In bending the crack
grew only beneath the surface, and growth was suppressed at the
deepest segment. This contrasts to tension where the crack breaks
through the thickness with uniform growth along the entire crack
front except at the free surface. Current investigations showed that
the crack growth developed under linear elastic fracture mechanics
conditions will no longer be applicable under ductile tearing
scenarios.
Abstract: Current research on semantic web aims at making intelligent web pages meaningful for machines. In this way, ontology plays a primary role. We believe that logic can help ontology languages (such as OWL) to be more fluent and efficient. In this paper we try to combine logic with OWL to reduce some disadvantages of this language. Therefore we extend OWL by logic and also show how logic can satisfy our future expectations of an ontology language.
Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: The increased use of biodiesel implies variations on both greenhouse gases and air pollutant emissions. Some studies point out that the use of biodiesel blends on diesel can help in controlling air pollution and promote a reduction of CO2 emissions. Reductions on PM, SO2, VOC and CO emissions are also expected, however NOx emissions may increase, which may potentiate O3 formation. This work aims to assess the impact of the biodiesel use on air quality, through a numerical modeling study, taking the Northern region of Portugal as a case study. The emission scenarios are focused on 2008 (baseline year) and 2020 (target year of Renewable Energy Directive-RED) and on three biodiesel blends (B0, B10 and B20). In a general way the use of biodiesel by 2020 will reduce the CO2 and air pollutants emissions in the Northern Portugal, improving air quality. However it will be in a very small extension.
Abstract: Currently, the demand for marine and fisheries commodity in Yogyakarta, Indonesia continues to increase. The existing condition shows that the aquaculture supply cannot be supplied by Yogyakarta region itself, but still need to be supported by regions outside Yogyakarta. The effort to optimize the market is initiated by reviewing and designing the supply chain of production and trade of aquaculture commodity in order to create the implementation of aquaculture production and trade commodity optimally. This formulated supply chain model indicates 4 performance indicators of measurable success in terms of: (1) efficiency; (2) flexibility; (3) responsiveness; and (4) quality. These indicators had been exercised as the success benchmarks for priority marketing management in local level as well as national level. The result of this research indicates that if the catfish fishery system is managed as business as usual then the catfish demand in Yogyakarta region will experience to increase in the future. The increase of demand is inline with the increase of number of people in Yogyakarta and also the fluctuation of catfish consumption per capita. The highest production of catfish will experience in the third year approximately 30,118 tons. Other result of the research indicates that the catfish demand in Yogyakarta region cannot be supplied yet from the local region. Therefore, to fulfill the supply from outside Yogyakarta region, the local farmers should improve the supply through land extension. The fluctuation of commodity price will experience in the future annually and the catfish supply from outside Yogyakarta region will be lowering the price in the market.
Abstract: Prolonged immobilization leads to significant
weakness and atrophy of the skeletal muscle and can also impair the
recovery of muscle strength following injury. Therefore, it is
important to minimize the period under immobilization and accelerate
the return to normal activity. This study examined the effects of heat
treatment and rest-inserted exercise on the muscle activity of the lower
limb during knee flexion/extension. Twelve healthy subjects were
assigned to 4 groups that included: (1) heat treatment + rest-inserted
exercise; (2) heat + continuous exercise; (3) no heat + rest-inserted
exercise; and (4) no heat + continuous exercise. Heat treatment was
applied for 15 mins prior to exercise. Continuous exercise groups
performed knee flexion/extension at 0.5 Hz for 300 cycles without rest
whereas rest-inserted exercise groups performed the same exercise but
with 2 mins rest inserted every 60 cycles of continuous exercise.
Changes in the rectus femoris and hamstring muscle activities were
assessed at 0, 1, and 2 weeks of treatment by measuring the
electromyography signals of isokinetic maximum voluntary
contraction. Significant increases in both the rectus femoris and
hamstring muscles were observed after 2 weeks of treatment only
when both heat treatment and rest-inserted exercise were performed.
These results suggest that combination of various treatment techniques,
such as heat treatment and rest-inserted exercise, may expedite the
recovery of muscle strength following immobilization.
Abstract: Wireless Mesh Networks (WMNs) are an emerging
technology for last-mile broadband access. In WMNs, similar to ad
hoc networks, each user node operates not only as a host but also as a
router. User packets are forwarded to and from an Internet-connected
gateway in multi-hop fashion. The WMNs can be integrated with
other networking technologies i.e. ad hoc networks, to implement a
smooth network extension. The meshed topology provides good
reliability and scalability, as well as low upfront investments. Despite
the recent start-up surge in WMNs, much research remains to be
done in standardizing the functional parameters of WMNs to fully
exploit their full potential. An edifice of the security concerns of
these networks is authentication of a new client joining an integrated
ad hoc network and such a scenario will require execution of a multihop
authentication technique. Our endeavor in this paper is to
introduce a secure authentication technique, with light over-heads
that can be conveniently implemented for the ad-hoc nodes forming
clients of an integrated WMN, thus facilitating their inter-operability.
Abstract: In this paper, the Lennard -Jones potential is applied
to molecules of liquid argon as well as its vapor and platinum as solid
surface in order to perform a non-equilibrium molecular dynamics
simulation to study the microscopic aspects of liquid-vapor-solid
interactions. The channel is periodic in x and y directions and along z
direction it is bounded by atomic walls. It was found that density of
the liquids near the solid walls fluctuated greatly and that the
structure was more like a solid than a liquid. This indicates that the
interactions of solid and liquid molecules are very strong. The
resultant surface tension, liquid density and vapor density are found
to be well predicted when compared with the experimental data for
argon. Liquid and vapor densities were found to depend on the cutoff
radius which induces the use of P3M (particle-particle particle-mesh)
method which was implemented for evaluation of force and surface
tension.