Abstract: The predictability of masonry arch bridges and their
behaviour is widely considered doubtful due to the lack of knowledge
about the conditions of a given masonry arch bridge. The assessment
methods for masonry arch bridges are MEXE, ARCHIE, RING and
Frame Analysis Method. The material properties of the masonry and
fill material are extremely difficult to determine accurately.
Consequently, it is necessary to examine the effect of load dispersal
angle through the fill material, the effect of variations in the stiffness
of the masonry, the tensile strength of the masonry mortar continuum
and the compressive strength of the masonry mortar continuum. It is
also important to understand the effect of fill material on load
dispersal angle to determine their influence on ratings. In this paper a
series of parametric studies, to examine the sensitivity of assessment
ratings to the various sets of input data required by the frame analysis
method, are carried out.
Abstract: This paper describes analysis of low velocity transverse impact on fully backed sandwich beams with composite faces from Eglass/epoxy and cores from Polyurethane or PVC. Indentation on sandwich beams has been analyzed with the existing theories and modeled with the FE code ABAQUS, also loadings have been done experimentally to verify theoretical results. Impact on fully backed has been modeled in two cases of impactor energy with SDOF model (single-degree-of-freedom) and indentation stiffness: lower energy for elastic indentation of sandwich beams and higher energy for plastic area in indentation. Impacts have been modeled by ABAQUS. Impact results can describe response of beam in terms of core and faces thicknesses, core material, indentor energy and energy absorbed. The foam core is modeled using the crushable foam material model and response of the foam core is experimentally characterized in uniaxial compression with higher velocity loading to define quasi impact behaviour.
Abstract: A new numerical method for simultaneously updating mass and stiffness matrices based on incomplete modal measured data is presented. By using the Kronecker product, all the variables that are to be modified can be found out and then can be updated directly. The optimal approximation mass matrix and stiffness matrix which satisfy the required eigenvalue equation and orthogonality condition are found under the Frobenius norm sense. The physical configuration of the analytical model is preserved and the updated model will exactly reproduce the modal measured data. The numerical example seems to indicate that the method is quite accurate and efficient.
Abstract: Optimization of rational geometrical and mechanical
parameters of panel with curved plywood ribs is considered in this
paper. The panel consists of cylindrical plywood ribs manufactured
from Finish plywood, upper and bottom plywood flange, stiffness
diaphragms. Panel is filled with foam. Minimal ratio of structure self
weight and load that could be applied to structure is considered as
rationality criteria. Optimization is done, by using classical beam
theory without nonlinearities. Optimization of discreet design
variables is done by Genetic algorithm.
Abstract: The paper considers a novel modular and intrinsically safe redundant robotic system with biologically inspired actuators (pneumatic artificial muscles and rubber bellows actuators). Similarly to the biological systems, the stiffness of the internal parallel modules, representing 2 DOF joints in the serial robotic chains, is controlled by co-activation of opposing redundant actuator groups in the null-space of the module Jacobian, without influencing the actual robot position. The decoupled position/stiffness control allows the realization of variable joint stiffness according to different force-displacement relationships. The variable joint stiffness, as well as limited pneumatic muscle/bellows force ability, ensures internal system safety that is crucial for development of human-friendly robots intended for human-robot collaboration. The initial experiments with the system prototype demonstrate the capabilities of independently, simultaneously controlling both joint (Cartesian) motion and joint stiffness. The paper also presents the possible industrial applications of snake-like robots built using the new modules.
Abstract: Buildings with floating column are highly undesirable built in seismically active areas. Many urban multi-storey buildings today have floating column buildings which are adopted to accommodate parking at ground floor or reception lobbies in the first storey. The earthquake forces developed at different floor levels in a building need to be brought down along the height to the ground by the shortest path; any deviation or discontinuity in this load transfer path results in poor performance of the building. Floating column buildings are severely damaged during earthquake. Damage on this structure can be reduce by taking the effect of infill wall. This paper presents the effect of stiffness of infill wall to the damage occurred in floating column building when ground shakes. Modelling and analysis are carried out by non linear analysis programme IDARC-2D. Damage occurred in beams, columns, storey are studied by formulating modified Park & Ang model to evaluate damage indices. Overall structural damage indices in buildings due to shaking of ground are also obtained. Dynamic response parameters i.e. lateral floor displacement, storey drift, time period, base shear of buildings are obtained and results are compared with the ordinary moment resisting frame buildings. Formation of cracks, yield, plastic hinge, are also observed during analysis.
Abstract: Utilization of waste material in asphalt pavement
would be beneficial in order to find an alternative solution to increase
service life of asphalt pavement and reduce environmental pollution
as well. One of these waste materials is Polyethylene Terephthalate
(PET) which is a type of polyester material and is produced in a large
extent. This research program is investigating the effects of adding
waste PET particles into the asphalt mixture with a maximum size of
2.36 mm. Different percentages of PET were added into the mixture
during dry process. Gap-graded mixture (SMA 14) and PG 80-100
asphalt binder have been used for this study. To evaluate PET
reinforced asphalt mixture different laboratory investigations have
been conducted on specimens. Marshall Stability test was carried
out. Besides, stiffness modulus test and indirect tensile fatigue test
were conducted on specimens at optimum asphalt content. It was
observed that in many cases PET reinforced SMA mixture had better
mechanical properties in comparison with control mixture.
Abstract: The demands of taller structures are becoming imperative almost everywhere in the world in addition to the challenges of material and labor cost, project time line etc. This paper conducted a study keeping in view the challenging nature of high-rise construction with no generic rules for deflection minimizations and frequency control. The effects of cyclonic wind and provision of outriggers on 28-storey, 42-storey and 57-storey are examined in this paper and certain conclusions are made which would pave way for researchers to conduct further study in this particular area of civil engineering. The results show that plan dimensions have vital impacts on structural heights. Increase of height while keeping the plan dimensions same, leads to the reduction in the lateral rigidity. To achieve required stiffness increase of bracings sizes as well as introduction of additional lateral resisting system such as belt truss and outriggers is required.
Abstract: GFRG(Glass Fiber Reinforced Gypsum) wall is a green product which can erect a building fast in prefabricated method, but its application to high-rise residential buildings is limited for its poor lateral stiffness. This paper has proposed a modification to GFRG walls structure to increase its lateral stiffness, which aiming to erect small high-rise residential buildings as load-bearing walls. The elastic finite element analysis to it has shown the lateral deformation feature and the distributions of the axial force and the shear force. The analysis results show that the new GFRG reinforced concrete wall can be used for small high-rise residential buildings.
Abstract: In construction of any structure, the aesthetic and utility values should be considered in such a way as to make the structure cost-effective. Most structures are composed of elements and joints which are very critical in any skeletal space structure because they majorly determine the performance of the structure. In early times, most space structures were constructed using rigid joints which had the advantage of better performing structures as compared to pin-jointed structures but with the disadvantage of requiring all the construction work to be done on site. The discovery of semi-rigid joints now enables connections to be prefabricated and quickly assembled on site while maintaining good performance. In this paper, cost-effective is discussed basing on strength of connectors at the joints, buckling of joints and overall structure, and the effect of initial geometrical imperfections. Several existing joints are reviewed by classifying them into categories and discussing where they are most suited and how they perform structurally. Also, finite element modeling using ABAQUS is done to determine the buckling behavior. It is observed that some joints are more economical than others. The rise to span ratio and imperfections are also found to affect the buckling of the structures. Based on these, general principles that guide the design of cost-effective joints and structures are discussed.
Abstract: The corrugated steel cladding used to cover most of
steel buildings is considered as non-structural element. This research
will reflect the effect of cladding as a shear diaphragm in increasing
the normal elastic capacity of columns. This study is important
because of the lack of information of the behavior of cladding and
secondary members in various codes. Mathematical models for six
different cases are carried by software. The results extracted from the
program have been plotted showing the effects of different variables
on the ultimate load of column. The variables considered in our
research are the spacing between columns and the thickness of the
corrugated sheet representing the sheet stiffness.
Abstract: Limited infrastructure development on peats and
organic soils is a serious geotechnical issues common to many
countries of the world especially Malaysia which distributed 1.5 mill
ha of those problematic soil. These soils have high water content and
organic content which exhibit different mechanical properties and
may also change chemically and biologically with time. Constructing
structures on peaty ground involves the risk of ground failure and
extreme settlement. Nowdays, much efforts need to be done in
making peatlands usable for construction due to increased landuse.
Deep mixing method employing cement as binders, is generally used
as measure again peaty/ organic ground failure problem. Where the
technique is widely adopted because it can improved ground
considerably in a short period of time. An understanding of
geotechnical properties as shear strength, stiffness and compressibility
behavior of these soils was requires before continues construction on
it. Therefore, 1- 1.5 meter peat soil sample from states of Johor and
an organic soil from Melaka, Malaysia were investigated. Cement
were added to the soil in the pre-mixing stage with water cement ratio
at range 3.5,7,14,140 for peats and 5,10,30 for organic soils,
essentially to modify the original soil textures and properties. The
mixtures which in slurry form will pour to polyvinyl chloride (pvc)
tube and cured at room temperature 250C for 7,14 and 28 days.
Laboratory experiments were conducted including unconfined
compressive strength and bender element , to monitor the improved
strength and stiffness of the 'stabilised mixed soils'. In between,
scanning electron miscroscopic (SEM) were observations to
investigate changes in microstructures of stabilised soils and to
evaluated hardening effect of a peat and organic soils stabilised
cement. This preliminary effort indicated that pre-mixing peat and
organic soils contributes in gaining soil strength while help the
engineers to establish a new method for those problematic ground
improvement in further practical and long term applications.
Abstract: The main objective of this article is to present the semi-active vibration control using an electro-rheological fluid embedded sandwich structure for a cantilever beam. ER fluid is a smart material, which cause the suspended particles polarize and connect each other to form chain. The stiffness and damping coefficients of the ER fluid can be changed in 10 micro seconds; therefore, ERF is suitable to become the material embedded in the tunable vibration absorber to become a smart absorber. For the ERF smart material embedded structure, the fuzzy control law depends on the experimental expert database and the proposed self-tuning strategy. The electric field is controlled by a CRIO embedded system to implement the real application. This study investigates the different performances using the Type-1 fuzzy and interval Type-2 fuzzy controllers. The Interval type-2 fuzzy control is used to improve the modeling uncertainties for this ERF embedded shock absorber. The self-tuning vibration controllers using Type-1 and Interval Type-2 fuzzy law are implemented to the shock absorber system. Based on the resulting performance, Internal Type-2 fuzzy is better than the traditional Type-1 fuzzy control for this vibration control system.
Abstract: In the various working field, vibration may cause injurious to human body. Especially, in case of the vibration which is constantly and repeatedly transferred to the human. That gives serious physical problem, so called, Reynaud phenomenon. In this paper, we propose a vibration transmissibility reduction module with flexure mechanism for personal tools. At first, we select a target personal tool, grass cutter, and measure the level of vibration transmissibility on the hand. And then, we develop the concept design of the module that has stiffness for reduction the vibration transmissibility more than 20%, where the vibration transmissibility is measured with an accelerometer. In addition, the vibration reduction can be enhanced when the interior gap between inner and outer body is filled with silicone gel. This will be verified by the further experiment.
Abstract: Steel plate shear walls (SPSWs) in buildings are
known to be an effective means for resisting lateral forces. By using
un-stiffened walls and allowing them to buckle, their energy
absorption capacity will increase significantly due to the postbuckling
capacity. The post-buckling tension field action of SPSWs
can provide substantial strength, stiffness and ductility. This paper
presents the Finite Element Analysis of low yield point (LYP) steel
shear walls. In this shear wall system, the LYP steel plate is used for
the steel panel and conventional structural steel is used for boundary
frames. A series of nonlinear cyclic analyses were carried out to
obtain the stiffness, strength, deformation capacity, and energy
dissipation capacity of the LYP steel shear wall. The effect of widthto-
thickness ratio of steel plate on buckling behavior, and energy
dissipation capacities were studied. Good energy dissipation and
deformation capacities were obtained for all models.
Abstract: In this paper we develop an efficient numerical method for the finite-element model updating of damped gyroscopic systems based on incomplete complex modal measured data. It is assumed that the analytical mass and stiffness matrices are correct and only the damping and gyroscopic matrices need to be updated. By solving a constrained optimization problem, the optimal corrected symmetric damping matrix and skew-symmetric gyroscopic matrix complied with the required eigenvalue equation are found under a weighted Frobenius norm sense.
Abstract: The machining performance is determined by the
frequency characteristics of the machine-tool structure and the
dynamics of the cutting process. Therefore, the prediction of dynamic
vibration behavior of spindle tool system is of great importance for the
design of a machine tool capable of high-precision and high-speed
machining. The aim of this study is to develop a finite element model
to predict the dynamic characteristics of milling machine tool and
hence evaluate the influence of the preload of the spindle bearings. To
this purpose, a three dimensional spindle bearing model of a high
speed engraving spindle tool was created. In this model, the rolling
interfaces with contact stiffness defined by Harris model were used to
simulate the spindle bearing components. Then a full finite element
model of a vertical milling machine was established by coupling the
spindle tool unit with the machine frame structure. Using this model,
the vibration mode that had a dominant influence on the dynamic
stiffness was determined. The results of the finite element simulations
reveal that spindle bearing with different preloads greatly affect the
dynamic behavior of the spindle tool unit and hence the dynamic
responses of the vertical column milling system. These results were
validated by performing vibration on the individual spindle tool unit
and the milling machine prototype, respectively. We conclude that
preload of the spindle bearings is an important component affecting
the dynamic characteristics and machining performance of the entire
vertical column structure of the milling machine.
Abstract: fibers of pure cellulose can be made from some bacteria such as acetobacter xylinum. Bacterial cellulose fibers are very pure, tens of nm across and about 0.5 micron long. The fibers are very stiff and, although nobody seems to have measured the strength of individual fibers. Their stiffness up to 70 GPa. Fundamental strengths should be at least greater than those of the best commercial polymers, but best bulk strength seems to about the same as that of steel. They can potentially be produced in industrial quantities at greatly lowered cost and water content, and with triple the yield, by a new process. This article presents a critical review of the available information on the bacterial cellulose as a biological nonwoven fabric with special emphasis on its fermentative production and applications. Characteristics of bacterial cellulose biofabric with respect to its structure and physicochemical properties are discussed. Current and potential applications of bacterial cellulose in textile, nonwoven cloth, paper, films synthetic fiber coating, food, pharmaceutical and other industries are also presented.
Abstract: Truss spars are used for oil exploitation in deep and ultra-deep water if storage crude oil is not needed. The linear hydrodynamic analysis of truss spar in random sea wave load is necessary for determining the behaviour of truss spar. This understanding is not only important for design of the mooring lines, but also for optimising the truss spar design. In this paper linear hydrodynamic analysis of truss spar is carried out in frequency domain. The hydrodynamic forces are calculated using the modified Morison equation and diffraction theory. Added mass and drag coefficients of truss section computed by transmission matrix and normal acceleration and velocity component acting on each element and for hull section computed by strip theory. The stiffness properties of the truss spar can be separated into two components; hydrostatic stiffness and mooring line stiffness. Then, platform response amplitudes obtained by solved the equation of motion. This equation is non-linear due to viscous damping term therefore linearised by iteration method [1]. Finally computed RAOs and significant response amplitude and results are compared with experimental data.
Abstract: A biophysically based multilayer continuum model of the facial soft tissue composite has been developed for simulating wrinkle formation. The deformed state of the soft tissue block was determined by solving large deformation mechanics equations using the Galerkin finite element method. The proposed soft tissue model is composed of four layers with distinct mechanical properties. These include stratum corneum, epidermal-dermal layer (living epidermis and dermis), subcutaneous tissue and the underlying muscle. All the layers were treated as non-linear, isotropic Mooney Rivlin materials. Contraction of muscle fibres was approximated using a steady-state relationship between the fibre extension ratio, intracellular calcium concentration and active stress in the fibre direction. Several variations of the model parameters (stiffness and thickness of epidermal-dermal layer, thickness of subcutaneous tissue layer) have been considered.