Abstract: In this paper, we present a numerical optical properties of a triangular periodic lattice of elliptical air holes. We report the influence of the ratio (semi-major axis length of elliptical hole to the filling ratio) on the photonic band gap. Then by using the finite difference time domain (FDTD) algorithm, the resonant wavelength of the point defect microcavities in a two-dimensional photonic crystal (PC) shifts towards the low wavelengths with significantly increased filing ratio. It can be noted that the Q factor is gradually changed to higher when the filling ratio increases. It is due to an increase in reflectivity of the PC mirror. Also we theoretically investigate the H1 cavity, where the value of semi-major axis (Rx) of the six holes surrounding the cavity are fixed at 0.5a and the Rx of the two edge air holes are fixed at the optimum value of 0.52a. The highest Q factor of 4.1359 × 106 is achieved at the resonant mode located at λ = 1.4970 µm.
Abstract: Fiber Bragg Grating (FBG) structure is an periodically modulated optical fiber. It acts as a selective filter of wavelength whose reflected peak is called Bragg wavelength and it depends on the period of the fiber and the refractive index. The simulation of FBG is based on solving the Coupled Mode Theory equation by using the Transfer Matrix Method which is carried out using MATLAB. It is found that spectral reflectivity is shifted when the change of temperature and strain is uniform. Under non-uniform temperature or strain perturbation, the spectrum is both shifted and destroyed. In case of transverse loading, reflectivity spectrum is split into two peaks, the first is specific to X axis, and the second belongs to Y axis. FBGs are used in civil engineering to detect perturbations applied to buildings.
Abstract: We have discovered an important technical solution that could make new approaches in the processing of wet silicon etching, especially in the production of photovoltaic cells. During its inferior light-trapping and structural properties, the inverted pyramid structure outperforms the conventional pyramid textures and black silicone. The traditional pyramid textures and black silicon can only be accomplished with more advanced lithography, laser processing, etc. Importantly, our data demonstrate the feasibility of an inverted pyramidal structure of silicon via one-step Cu-catalyzed chemical etching (CCCE) in Cu (NO3)2/HF/H2O2/H2O solutions. The effects of etching time and reaction temperature on surface geometry and light trapping were systematically investigated. The conclusion shows that the inverted pyramid structure has ultra-low reflectivity of ~4.2% in the wavelength of 300~1000 nm; introduce of Cu particles can significantly accelerate the dissolution of the silicon wafer. The etching and the inverted pyramid structure formation mechanism are discussed. Inverted pyramid structure with outstanding anti-reflectivity includes useful applications throughout the manufacture of semi-conductive industry-compatible solar cells, and can have significant impacts on industry colleagues and populations.
Abstract: Mining by block or panel caving is a mining method that takes advantage of fractures within an ore body, coupled with gravity, to extract material from a predetermined column of ore. The caving column is weakened from beneath through the use of undercutting, after which the ore breaks up and is extracted from below in a continuous cycle. The nature of this method induces cyclical stresses on the pillars of excavations as stress is built up and released over time, which has a detrimental effect on both the installed ground support and the rock mass itself. Ground support capacity, especially on the production where excavation void ratio is highest, is subjected to heavy loading. Strain above threshold of the elongation of support capacity can yield resulting in damage to excavations. Geotechnical engineers must evaluate not only the remnant capacity of ground support systems but also investigate depth of rock mass yield within pillars, backs and floors. Ground Penetrating Radar (GPR) is a geophysical method that has the ability to evaluate rock mass damage using electromagnetic waves. This paper illustrates a case study from the Grasberg mining complex where non-invasive information on the depth of damage and condition of the remaining rock mass was required. GPR with 100 MHz antenna resolution was used to obtain images of the subsurface to determine rehabilitation requirements prior to recommencing production activities. The GPR surveys were used to calibrate the reflection coefficient response of varying rock mass conditions to known Rock Quality Designation (RQD) parameters observed at the mine. The calibrated GPR survey allowed site engineers to map subsurface conditions and plan rehabilitation accordingly.
Abstract: Relation between tolerance class and indispensable attribute and knowledge dependency in rough set model with tolerance relation is explored. After giving definitions and concepts of knowledge dependency and knowledge dependency degree for incomplete information system in tolerance rough set model by distinguishing decision attribute containing missing attribute value or not, the result of maintaining reflectivity, transitivity, augmentation, decomposition law and merge law for complete knowledge dependency is proved. Knowledge dependency degrees (not complete knowledge dependency degrees) only satisfy some laws after transitivity, augmentation and decomposition operations. An algorithm to solve attribute reduction in an incomplete decision table is designed. The correctness is checked by an example.
Abstract: Optical properties of bulk and thin film of 1H-CaAlSi for two directions (1,0,0) and (0,0,1) were studied. The calculations are carried out by Density Functional Theory (DFT) method using full potential. GGA approximation was used to calculate exchange-correlation energy. The calculations are performed by WIEN2k package. The results showed that the absorption edge is shifted backward 0.82eV in the thin film than the bulk for both directions. The static values of the real part of dielectric function for four cases were obtained. The static values of the refractive index for four cases are calculated too. The reflectivity graphs have shown an intensive difference between the reflectivity of the thin film and the bulk in the ultraviolet region.
Abstract: Low density polyethylene (LDPE) nanocomposites
with 3, 5 and 7 wt. % cobalt ferrite (CoFe2O4) nanopowder fabricated
with extrusion mixing and followed up by hot press to reach compact
samples. The transmission/reflection measurements were carried out
with a network analyzer in the frequency range of 8-12 GHz. By
increasing the percent of CoFe2O4 nanopowder, reflection loss (S11)
increases, while transferring loss (S21) decreases. Reflectivity (R)
calculations made using S11 and S21. Increase in percent of CoFe2O4
nanopowder up to 7 wt. % in composite leaded to higher reflectivity
amount, and revealed that increasing the percent of CoFe2O4
nanopowder up to 7 wt. % leads to further microwave absorption in
8-12 GHz range.
Abstract: The occurrences of precipitation, also commonly
referred as rain, in the form of "convective" and "stratiform" have
been identified to exist worldwide. In this study, the radar return
echoes or known as reflectivity values acquired from radar scans
have been exploited in the process of classifying the type of rain
endured. The investigation use radar data from Malaysian
Meteorology Department (MMD). It is possible to discriminate the
types of rain experienced in tropical region by observing the vertical
characteristics of the rain structure. .Heavy rain in tropical region
profoundly affects radiowave signals, causing transmission
interference and signal fading. Required wireless system fade margin
depends on the type of rain. Information relating to the two
mentioned types of rain is critical for the system engineers and
researchers in their endeavour to improve the reliability of
communication links. This paper highlights the quantification of
percentage occurrences over one year period in 2009.
Abstract: This paper presents effects of the mean operating
pressure on the optimal operating frequency based on temperature
differences across stack ends in a thermoacoustic refrigerator. In
addition to the length of the resonance tube, components of the
thermoacoustic refrigerator have an influence on the operating
frequency due to their acoustic properties, i.e., absorptivity,
reflectivity and transmissivity. The interference of waves incurs and
distorts the original frequency generated by the driver so that the
optimal operating frequency differs from the designs. These acoustic
properties are not parameters in the designs and be very complicated
to infer their responses. A prototype thermoacoustic refrigerator is
constructed and used to investigate its optimal operating frequency
compared to the design at various operating pressures. Helium and air
are used as working fluids during the experiments. The results
indicate that the optimal operating frequency of the prototype
thermoacoustic refrigerator using helium is at 6 bar and 490Hz or
approximately 20% away from the design frequency. The optimal
operating frequency at other mean pressures differs from the design
in an unpredictable manner, however, the optimal operating
frequency and pressure can be identified by testing.
Abstract: Narrow bandwidth and high loss performance limits the use of reflectarray antennas in some applications. This article reports on the feasibility of employing strategic reflectarray resonant elements to characterize the reflectivity performance of reflectarrays in X-band frequency range. Strategic reflectarray resonant elements incorporating variable substrate thicknesses ranging from 0.016λ to 0.052λ have been analyzed in terms of reflection loss and reflection phase performance. The effect of substrate thickness has been validated by using waveguide scattering parameter technique. It has been demonstrated that as the substrate thickness is increased from 0.508mm to 1.57mm the measured reflection loss of dipole element decreased from 5.66dB to 3.70dB with increment in 10% bandwidth of 39MHz to 64MHz. Similarly the measured reflection loss of triangular loop element is decreased from 20.25dB to 7.02dB with an increment in 10% bandwidth of 12MHz to 23MHz. The results also show a significant decrease in the slope of reflection phase curve as well. A Figure of Merit (FoM) has also been defined for the comparison of static phase range of resonant elements under consideration. Moreover, a novel numerical model based on analytical equations has been established incorporating the material properties of dielectric substrate and electrical properties of different reflectarray resonant elements to obtain the progressive phase distribution for each individual reflectarray resonant element.
Abstract: To analyze the behavior of Petri nets, the accessibility
graph and Model Checking are widely used. However, if the
analyzed Petri net is unbounded then the accessibility graph becomes
infinite and Model Checking can not be used even for small Petri
nets. ECATNets [2] are a category of algebraic Petri nets. The main
feature of ECATNets is their sound and complete semantics based on
rewriting logic [8] and its language Maude [9]. ECATNets analysis
may be done by using techniques of accessibility analysis and Model
Checking defined in Maude. But, these two techniques supported by
Maude do not work also with infinite-states systems. As a category
of Petri nets, ECATNets can be unbounded and so infinite systems.
In order to know if we can apply accessibility analysis and Model
Checking of Maude to an ECATNet, we propose in this paper an
algorithm allowing the detection if the ECATNet is bounded or not.
Moreover, we propose a rewriting logic based tool implementing this
algorithm. We show that the development of this tool using the
Maude system is facilitated thanks to the reflectivity of the rewriting
logic. Indeed, the self-interpretation of this logic allows us both the
modelling of an ECATNet and acting on it.
Abstract: We report the electronic structure and optical
properties of NdF3 compound. Our calculations are based on density
functional theory (DFT) using the full potential linearized augmented
plane wave (FPLAPW) method with the inclusion of spin orbit
coupling. We employed the local spin density approximation (LSDA)
and Coulomb-corrected local spin density approximation, known for
treating the highly correlated 4f electrons properly, is able to
reproduce the correct insulating ground state. We find that the
standard LSDA approach is incapable of correctly describing the
electronic properties of such materials since it positions the f-bands
incorrectly resulting in an incorrect metallic ground state. On the
other hand, LSDA + U approximation, known for treating the highly
correlated 4f electrons properly, is able to reproduce the correct
insulating ground state. Interestingly, however, we do not find any
significant differences in the optical properties calculated using
LSDA, and LSDA + U suggesting that the 4f electrons do not play a
decisive role in the optical properties of these compounds. The
reflectivity for NdF3 compound stays low till 7 eV which is
consistent with their large energy gaps. The calculated energy gaps
are in good agreement with experiments. Our calculated reflectivity
compares well with the experimental data and the results are analyzed
in the light of band to band transitions.
Abstract: Structural and UV/Visible optical properties can be
useful to describe a material for the CIGS solar cell active layer,
therefore, this work demonstrates the properties like surface
morphology, X-ray Photoelectron Spectroscopy (XPS) bonding
energy (EB) core level spectra, UV/Visible absorption spectra,
refractive index (n), optical energy band (Eg), reflection spectra for
the Cu25 (In16Ga9) Se40Te10 (CIGST-1) and Cu20 (In14Ga9) Se45Te12
(CIGST-2) chalcogenide compositions. Materials have been
exhibited homogenous surface morphologies, broading /-or diffusion
of bonding energy peaks relative elemental values and a high
UV/Visible absorption tendency in the wave length range 400 nm-
850 nm range with the optical energy band gaps 1.37 and 1.42
respectively. Subsequently, UV/Visible reflectivity property in the
wave length range 250 nm to 320 nm for these materials has also
been discussed.
Abstract: ZnO nanostructures including nanowires, nanorods,
and nanoneedles were successfully deposited on GaAs substrates,
respectively, by simple two-step chemical method for the first time. A
ZnO seed layer was firstly pre-coated on the O2-plasma treated
substrate by sol-gel process, followed by the nucleation of ZnO
nanostructures through hydrothermal synthesis. Nanostructures with
different average diameter (15-250 nm), length (0.9-1.8 μm), density
(0.9-16×109 cm-2) were obtained via adjusting the growth time and
concentration of precursors. From the reflectivity spectra, we
concluded ordered and taper nanostructures were preferential for
photovoltaic applications. ZnO nanoneedles with an average diameter
of 106 nm, a moderate length of 2.4 μm, and the density of 7.2×109
cm-2 could be synthesized in the concentration of 0.04 M for 18 h.
Integrated with the nanoneedle array, the power conversion efficiency
of single junction solar cell was increased from 7.3 to 12.2%,
corresponding to a 67% improvement.
Abstract: Support Vector Machine (SVM) is a statistical
learning tool that was initially developed by Vapnik in 1979 and later
developed to a more complex concept of structural risk minimization
(SRM). SVM is playing an increasing role in applications to
detection problems in various engineering problems, notably in
statistical signal processing, pattern recognition, image analysis, and
communication systems. In this paper, SVM was applied to the
detection of SAR (synthetic aperture radar) images in the presence of
partially developed speckle noise. The simulation was done for single
look and multi-look speckle models to give a complete overlook and
insight to the new proposed model of the SVM-based detector. The
structure of the SVM was derived and applied to real SAR images
and its performance in terms of the mean square error (MSE) metric
was calculated. We showed that the SVM-detected SAR images have
a very low MSE and are of good quality. The quality of the
processed speckled images improved for the multi-look model.
Furthermore, the contrast of the SVM detected images was higher
than that of the original non-noisy images, indicating that the SVM
approach increased the distance between the pixel reflectivity levels
(the detection hypotheses) in the original images.
Abstract: In cancer progress, the optical properties of tissues
like absorption and scattering coefficient change, so by these
changes, we can trace the progress of cancer, even it can be applied
for pre-detection of cancer. In this paper, we investigate the effects of
changes of optical properties on light penetrated into tissues. The
diffusion equation is widely used to simulate light propagation into
biological tissues. In this study, the boundary integral method (BIM)
is used to solve the diffusion equation. We illustrate that the changes
of optical properties can modified the reflectance or penetrating light.
Abstract: Support Vector Machine (SVM) is a statistical learning tool that was initially developed by Vapnik in 1979 and later developed to a more complex concept of structural risk minimization (SRM). SVM is playing an increasing role in applications to detection problems in various engineering problems, notably in statistical signal processing, pattern recognition, image analysis, and communication systems. In this paper, SVM was applied to the detection of medical ultrasound images in the presence of partially developed speckle noise. The simulation was done for single look and multi-look speckle models to give a complete overlook and insight to the new proposed model of the SVM-based detector. The structure of the SVM was derived and applied to clinical ultrasound images and its performance in terms of the mean square error (MSE) metric was calculated. We showed that the SVM-detected ultrasound images have a very low MSE and are of good quality. The quality of the processed speckled images improved for the multi-look model. Furthermore, the contrast of the SVM detected images was higher than that of the original non-noisy images, indicating that the SVM approach increased the distance between the pixel reflectivity levels (detection hypotheses) in the original images.