Abstract: Effective treatment of ground instability is essential when managing the impacts associated with historic mining. A field trial was undertaken by the Coal Authority to investigate the geotechnical performance and potential use of composite materials comprising resin and fill or stone to safely treat surface collapses, such as crown-holes, associated with shallow mining. Test pits were loosely filled with various granular fill materials. The fill material was injected with commercially available silicate and polyurethane resin foam products. In situ and laboratory testing was undertaken to assess the geotechnical properties of the resultant composite materials. The test pits were subsequently excavated to assess resin permeation. Drilling and resin injection was easiest through clean limestone fill materials. Recycled building waste fill material proved difficult to inject with resin; this material is thus considered unsuitable for use in resin composites. Incomplete resin permeation in several of the test pits created irregular ‘blocks’ of composite. Injected resin foams significantly improve the stiffness and resistance (strength) of the un-compacted fill material. The stiffness of the treated fill material appears to be a function of the stone particle size, its associated compaction characteristics (under loose tipping) and the proportion of resin foam matrix. The type of fill material is more critical than the type of resin to the geotechnical properties of the composite materials. Resin composites can effectively support typical design imposed loads. Compared to other traditional treatment options, such as cement grouting, the use of resin composites is potentially less disruptive, particularly for sites with limited access, and thus likely to achieve significant reinstatement cost savings. The use of resin composites is considered a suitable option for the future treatment of shallow mining collapses.
Abstract: Water is essential for life and fresh water is a finite
resource that is becoming scarce day by day even though it is
recycled by hydrological cycle. The fresh water reserves are being
polluted due to expanding irrigation, industries, urban population and
its development. Contaminated water leads to several health
problems. With the increasing demand of fresh water, solar
distillation is an alternate solution which uses solar energy to
evaporate water and then to condense it, thereby collecting distilled
water within or outside the same system to use it as potable water.
The structure that houses the process is known as a 'solar still'. In this
paper, ‘Modified double slope solar still (MDSSS)’ & 'Modified
double slope basin type multiwick solar still (MDSBMSS)' have been
designed to convert saline, brackish water into drinking water. In this
work two different modified solar stills are fabricated to study the
performance of these solar stills. For modification of solar stills,
Fibre Reinforced Plastic (FRP) and Acrylic sheets are used. The
experiments in MDSBMSS and MDSSS was carried on 10
September 2015 & 5 November 2015 respectively. Performances of
the stills were investigated. The amount of distillate has been found
3624 Ml/day in MDSBMSS on 10 September 2015 and 2400 Ml/day
in MDSSS on 5 November 2015.
Abstract: Sclareolide is made from sclareol by oxidiative synthesis and subsequent crystallization, while the crystallization mother liquor still contains 15%~30%wt of sclareolide to be reclaimed. With the reaction material of sclareol is provided as plant extract, many sorts of complex impurities exist in the mother liquor. Due to the difficulty in recycling sclareolide after solvent recovery, it is common practice for the factories to discard the mother liquor, which not only results in loss of sclareolide, but also contributes extra environmental burden. In this paper, a process based on adsorption and elution has been presented for recycling of sclareolide from mother liquor. After pretreatment of the crystallization mother liquor by HZ-845 resin to remove parts of impurities, sclareolide is adsorbed by HZ-816 resin. The HZ-816 resin loaded with sclareolide is then eluted by elution solvent. Finally, the eluent containing sclareolide is concentrated and fed into the crystallization step in the process. By adoption of the recycle from mother liquor, total yield of sclareolide increases from 86% to 90% with a stable purity of the final sclareolide products maintained.
Abstract: The application of recycle waste tires into civil
engineering practices, namely asphalt paving mixtures and cementbased
materials has been gaining ground across the world. This
review summarizes and compares the recent achievements in the area
of plain rubberized concrete (PRC), in details. Different treatment
methods have been discussed to improve the performance of
rubberized Portland cement concrete. The review also includes the
effects of size and amount of tire rubbers on mechanical and
durability properties of PRC. The microstructure behaviour of the
rubberized concrete was detailed.
Abstract: With the strengthened regulation on the mandatory use
of recycled aggregate, development of construction materials using
recycled aggregate has recently increased. This study aimed to secure
the performance of asphalt concrete mixture by developing
recycled-modified asphalt using recycled basalt aggregate from the
Jeju area. The strength of the basalt aggregate from the Jeju area used
in this study was similar to that of general aggregate, while the specific
surface area was larger due to the development of pores. Modified
asphalt was developed using a general aggregate-recycled aggregate
ratio of 7:3, and the results indicated that the Marshall stability
increased by 27% compared to that of asphalt concrete mixture using
only general aggregate, and the flow values showed similar levels.
Also, the indirect tensile strength increased by 79%, and the toughness
increased by more than 100%. In addition, the TSR for examining
moisture resistance was 0.95 indicating that the reduction in the
indirect tensile strength due to moisture was very low (5% level), and
the developed recycled-modified asphalt could satisfy all the quality
standards of asphalt concrete mixture.
Abstract: Customer’ needs, quality, and value creation while
reducing costs through supply chain management provides challenges
and opportunities for companies and researchers. In the light of these
challenges, modern ideas must contribute to counter these challenges
and exploit opportunities. Therefore, this paper discusses the impact
of the quality cost on revenue sharing as a most important incentive
to configure business networks. This paper develops the quality cost approach to align with the
modern era. It develops a model to measure quality costs which
might enable firms to manage revenue sharing in a supply chain. The
developed model includes five categories; besides the well-known
four categories (namely prevention costs, appraisal costs, internal
failure costs, and external failure costs), a new category has been
developed in this research as a new vision of the relationship between
quality costs and innovations in industry. This new category is
Recycle Cost. This paper also examines whether such quality costs in
supply chains influence the revenue sharing between partners. Using the author's quality cost model, the relationship between
quality costs and revenue sharing among partners is examined using a
case study in an Egyptian manufacturing company which is a part of
a supply chain. This paper argues that the revenue-sharing proportion
allocated to supplier increases as the recycle cost of supplier
increases, and the revenue-sharing proportion allocated to
manufacturer increases as the prevention and appraisal costs increase,
as well as the failure costs, the recycle costs of manufacturer, and the
recycle costs of suppliers decrease. However, the results present
surprising findings. The purposes of this study are developing quality cost approach
and understanding the relationships between quality costs and
revenue sharing in supply chains. Therefore, the present study
contributes to theory and practice by explaining how the cost of
recycling can be combined in quality cost model to better
understanding the revenue sharing among partners in supply chains.
Abstract: Large quantities of solid wastes being generated
worldwide from sources such as household, domestic, industrial,
commercial and construction demolition activities, leads to
environmental concerns. Utilization of these wastes in making
building construction materials can reduce the magnitude of the
associated problems. When these waste products are used in place of
other conventional materials, natural resources and energy are
preserved and expensive and/or potentially harmful waste disposal is
avoided. Recycling which is regarded as the third most preferred waste
disposal option, with its numerous environmental benefits, stand as a
viable option to offset the environmental impact associated with the
construction industry. This paper reviews the results of laboratory tests and important
research findings, and the potential of using these wastes in building
construction materials with focus on sustainable development.
Research gaps, which includes; the need to develop standard mix
design for solid waste based building materials; the need to develop
energy efficient method of processing solid waste use in concrete; the
need to study the actual behavior or performance of such building
materials in practical application and the limited real life application
of such building materials have also been identified. A research is being proposed to develop an environmentally
friendly, lightweight building block from recycled waste paper,
without the use of cement, and with properties suitable for use as
walling unit. This proposed research intends to incorporate,
laboratory experimentation and modeling to address the identified
research gaps.
Abstract: Diets high in processed foods have been found to lack
essential micro-nutrients for optimum human development and
overall health. Some micro-nutrients such as copper (Cu) have been
found to enhance the inflammatory response through its oxidative
functions, thereby having a role in cardiovascular disease, metabolic
syndrome, diabetes and related complications. This research study
was designed to determine if food crops could be bio-fortified with
micro-nutrients by growing sprouts on mineral fortified fiber mats. In
the feasibility study described in this contribution, recycled cellulose
fibers and clay, saturated with either micro-nutrient copper ions or
copper nanoparticles, were converted to a novel mineral-cellulose
fiber carrier of essential micro-nutrient and of antimicrobial
properties. Seeds of Medicago sativa (alfalfa), purchased from a
commercial, organic supplier were germinated on engineered
cellulose fiber mats. After the appearance of the first leaves, the
sprouts were dehydrated and analyzed for Cu content. Nutrient
analysis showed ~2 increase in Cu of the sprouts grown on the fiber
mats with copper particles, and ~4 increase on mats with ionic copper
as compared to the control samples. This study illustrates the
potential for the use of engineered mats as a viable way to increase
the micro-nutrient composition of locally-grown food crops and the
need for additional research to determine the uptake, nutritional
implications and risks of micro-nutrient bio-fortification.
Abstract: Public participation in recycling domestic waste is still
very low in Malaysia. Only 10.5% of solid waste was recycled up to
now which is far below than of in developed countries. Therefore,
understanding public motivations towards recycling domestic waste
are important to improve current recycling rate. Thus, this study
attempts to identify what are the possible motivations and hindrances
for the public to recycle. Open-ended questions format were
administered to 484 people in Kota Kinabalu, Sabah, Malaysia. Two
specific questions we asked to explore their general determinants and
barriers in practicing recycling: “What motivates you to recycle?”
and “What are the barriers you encountered in doing recycling
activities?” Thematic was conducted on the open-ended questions in
which themes were created with the raw comments. It was found that
the underlying recycling motivations are (i) awareness’ towards the
environment; (ii) benefits to the society and individual; and (iii)
social influence. Non participations are influence by (i) attitudes; (ii)
commitment; (iii) facilities; (iv) knowledge; (v) inconvenience; and
(vi) enforcement.
Abstract: Concrete is strong in compression however weak in
tension. The tensile strength as well as ductile property of concrete
could be improved by addition of short dispersed fibers. Polyethylene
terephthalate (PET) fiber obtained from hand cutting or mechanical
slitting of plastic sheets generally used as discrete reinforcement in
substitution of steel fiber. PET fiber obtained from the former process
is in the form of straight slit sheet pattern that impart weaker
mechanical bonding behavior in the concrete matrix. To improve the
limitation of straight slit sheet fiber the present study considered two
additional geometry of fiber namely (a) flattened end slit sheet and
(b) deformed slit sheet. The mix for plain concrete was design for a
compressive strength of 25 MPa at 28 days curing time with a watercement
ratio of 0.5. Cylindrical and beam specimens with 0.5% fibers
volume fraction and without fibers were cast to investigate the
influence of geometry on the mechanical properties of concrete. The
performance parameters mainly studied include flexural strength,
splitting tensile strength, compressive strength and ultrasonic pulse
velocity (UPV). Test results show that geometry of fiber has a
marginal effect on the workability of concrete. However, it plays a
significant role in achieving a good compressive and tensile strength
of concrete. Further, significant improvement in term of flexural and
energy dissipation capacity were observed from other fibers as
compared to the straight slit sheet pattern. Also, the inclusion of PET
fiber improved the ability in absorbing energy in the post-cracking
state of the specimen as well as no significant porous structures.
Abstract: New environmental regulations and the increasing
market preference for companies that respect the ecosystem had
encouraged the industry to look after new treatments for its effluents.
The sugar industry, one of the largest emitter of environmental
pollutants, follows this tendency. Membrane technology is
convenient for separation of suspended solids, colloids and high
molecular weight materials that are present in a wastewater from
sugar industry. The idea is to microfilter the wastewater, where the
permeate passes through the membrane and becomes available for
recycle and re-use in the sugar manufacturing process. For
microfiltration of this effluent a tubular ceramic membrane was used
with a pore size of 200 nm at transmembrane pressure in range of 1–3
bars and in range of flow rate of 50–150 l/h. Kenics static mixer was
used for permeate flux enhancement. Turbidity and suspended solids
were removed and the permeate flux was continuously monitored
during the microfiltration process. The flux achieved after 90 minutes
of microfiltration was in a range of 50–70 l/m2h. The obtained
turbidity decrease was in the range of 50-99 % and total amount of
suspended solids was removed.
Abstract: This paper presents results of compressive strength,
capillary water absorption, and density tests conducted on concrete
containing recycled aggregate (RCA) which is obtained from
structural waste generated by the construction industry in Turkey. In
the experiments, 0%, 15%, 30%, 45% and 60% of the normal
(natural) coarse aggregate was replaced by the recycled aggregate.
Maximum aggregate particle sizes were selected as 16 mm, 22,4 mm
and 31,5 mm; and 0,06%, 0,13% and 0,20% of air-entraining agent
(AEA) were used in mixtures. Fly ash and superplasticizer were used
as a mineral and chemical admixture, respectively. The same type
(CEM I 42.5) and constant dosage of cement were used in the study.
Water/cement ratio was kept constant as 0.53 for all mixture. It was
concluded that capillary water absorption, compressive strength, and
density of concrete decreased with increasing RCA ratio. Increasing
in maximum aggregate particle size and amount of AEA also affect
the properties of concrete significantly.
Abstract: It is the worldwide problem that the recycled PVB is
not recycled and it is wildly stored in landfills. However, PVB has
similar chemical properties such as PVC. Moreover, both of these
polymers are plasticized. Therefore, the study of thermal properties
of plasticized PVC and the recycled PVB obtained by recycling of
windshields is carried out. This work has done in order to find nondegradable
processing conditions applicable for both polymers.
Tested PVC contained 38% of plasticizer diisononyl phthalate
(DINP) and PVB was plasticized with 28% of triethylene glycol,
bis(2-ethylhexanoate) (3GO). The thermal and thermo-oxidative
decomposition of both vinyl polymers are compared by calorimetric
analysis and by tensile strength analysis.
Abstract: The secondary alloy A226 is used for many
automotive casting produced by mould casting and high pressure die
casting. This alloy has excellent castability, good mechanical
properties and cost-effectiveness. Production of primary aluminium
alloys belong to heavy source fouling of life environs. The European
Union calls for the emission reduction and reduction in energy
consumption therefore increase production of recycled (secondary)
aluminium cast alloys. The contribution is deal with influence of
recycling on the quality of the casting made from A226 in automotive
industry. The properties of the casting made from secondary
aluminium alloys were compared with the required properties of
primary aluminium alloys. The effect of recycling on microstructure
was observed using combination different analytical techniques (light
microscopy upon black-white etching, scanning electron microscopy
- SEM upon deep etching and energy dispersive X-ray analysis -
EDX). These techniques were used for the identification of the
various structure parameters, which was used to compare secondary
alloy microstructure with primary alloy microstructure.
Abstract: This paper is aimed to the use of different types of
industrial wastes in concrete production. From examined waste
(crushed concrete waste) our tested concrete samples with dimension
150 mm were prepared. In these samples, fractions 4/8 mm and 8/16
mm by recycled concrete aggregate with a range of variation from 0
to 100% were replaced. Experiment samples were tested for
compressive strength after 2, 7, 14 and 28 days of hardening.
From obtained results it is evident that all samples prepared with
washed recycled concrete aggregates met the requirement of standard
for compressive strength of 20 MPa already after 14 days of
hardening. Sample prepared with recycled concrete aggregates (4/8
mm: 100% and 8/16 mm: 60%) reached 101% of compressive
strength value (34.7 MPa) after 28 days of hardening in comparison
with the reference sample (34.4 MPa). The lowest strength after 28
days of hardening (27.42 MPa) was obtained for sample consisting of
recycled concrete in proportion of 40% for 4/8 fraction and 100% for
8/16 fraction of recycled concrete.
Abstract: In this work, two fermentations at different
temperatures (25 and 30ºC), with cell recycling, were accomplished
to produce ethanol, using a mix of commercial substrates, xylose
(70%) and glucose (30%), as organic source for Scheffersomyces
stipitis. Five consecutive fermentations of 80 g L-1 (1º, 2º and 3º
recycles), 96 g L-1 (4º recycle) and 120 g L-1 (5º recycle)reduced
sugars led to a final maximum ethanol concentration of 17.2 and 34.5
g L-1, at 25 and 30ºC, respectively. Glucose was the preferred
substrate; moreover xylose startup degradation was initiated after a
remaining glucose presence in the medium. Results showed that yeast
acid treatment, performed before each cycle, provided improvements
on cell viability, accompanied by ethanol productivity of 2.16 g L-1 h-
1 at 30ºC. A maximum 36% of xylose was retained in the
fermentation medium and after five-cycle fermentation an ethanol
yield of 0.43 g ethanol/g sugars was observed. S. stipitis fermentation
capacity and tolerance showed better results at 30ºC with 83.4% of
theoretical yield referenced on initial biomass.
Abstract: The model tests were conducted in the laboratory
without and with Plastic recycled polymer in fly ash steep slopes
overlaying soft foundation soils like fly ash and powai soil in order to
check the stability of steep slope. In this experiment, fly ash is used
as a filling material and Plastic Recycled Polymers of diameter =
3mm and length = 4mm were made from waste plastic product (lower
grade plastic product). The properties of fly ash and Plastic recycled
polymers are determined. From the experiments, load and settlement
have measured. From these data, load –settlement curves have
reported. It has been observed from test results that load carrying
capacity of mixture fly ash with Plastic Recycled Polymers slope is
more than that of fly ash slope. The deformation of Plastic Recycled
Polymers slope is slightly more than that of fly ash slope. A Finite
Element Method (F.E.M.) was also evaluated using PLAXIS 3D
version. The failure pattern, deformations and factor of safety are
reported based on analytical programme. The results from
experimental data and analytical programme are compared and
reported.
Abstract: The thermal performance of a solar water heating with
1.00 m2 flat plate collectors in Cascavel - PR, is which presented in
this article, paper presents the solution to leverage the marketing of
solar heating systems through detailed constituent materials of the
solar collector studies, these abundant materials in construction, such
as expanded polyethylene, PVC, aluminum and glass tubes, mixing
them with new materials to minimize loss of efficiency while
decreasing its cost. The system was tested during months and the
collector obtained maximum recorded temperature of outlet fluid of
55°C, while the maximum temperature of the water at the bottom of
the hot water tank was 35°C. The average daily energy collected was
19.6 MJ/d; the energy supplied by the solar plate was 16.2 MJ/d; the
loss in the feed pipe was 3.2 MJ/d; the solar fraction was 32.2%, the
efficiency of the collector was 45.6% and the efficiency of the system
was 37.8%.
Abstract: Degradation of agricultural soils has increased rapidly
during the last 20 years due to the indiscriminate use of pesticides
and other anthropogenic activities. Currently, there is an urgent need
of soil restoration to increase agricultural production. Utilization of
sewage sludge or municipal solid waste is an important way to
recycle nutrient elements and improve soil quality. With these
amendments, nutrient availability in the aqueous phase might be
increased and production of healthier crops can be accomplished.
This research project aimed to achieve sustainable management of
tropical agricultural soils, specifically in Puerto Rico, through the
amendment of water treatment plant sludge’s. This practice avoids
landfill disposal of sewage sludge and at the same time results costeffective
practice for recycling solid waste residues. Coriander
sativum was cultivated in a compost-soil-sludge mixture at different
proportions. Results showed that Coriander grown in a mixture of
25% compost+50% Voladora soi+25% sludge had the best growth
and development. High chlorophyll content (33.01 ± 0.8) was
observed in Coriander plants cultivated in 25% compost+62.5%
Coloso soil+ 12.5% sludge compared to plants grown with no sludge
(32.59 ± 0.7). ICP-OES analysis showed variations in mineral
element contents (macro and micronutrients) in coriander plant
grown I soil amended with sludge and compost.
Abstract: Solid waste management in steel industry is broadly
classified in “4 Rs” i.e. reduce, reuse, recycle and restore the
materials. Reuse and recycling the entire solid waste generated in the
process of steel making is a viable solution in targeting a clean, green
and zero waste technology leading to sustainable development of the
steel industry. Solid waste management has gained importance in
steel industry in view of its uncertainty, volatility and speculation due
to world competitive standards, rising input costs, scarcity of raw
materials and solid waste generated like in other sectors. The
challenges that the steel Industry faces today are the requirement of a
sustainable development by meeting the needs of our present
generation without compromising the ability of future generations.
Technologies are developed not only for gainful utilization of solid
wastes in manufacture of conventional products but also for
conversion of same in to completely new products.