Abstract: Radiation shielding is an obstacle in long duration space exploration. Boron Nitride Nanotubes (BNNTs) have attracted attention as an additive to radiation shielding material due to B10’s large neutron capture cross section. The B10 has an effective neutron capture cross section suitable for low energy neutrons ranging from 10-5 to 104 eV and hydrogen is effective at slowing down high energy neutrons. Hydrogenated BNNTs are potentially an ideal nanofiller for radiation shielding composites. We use Molecular Dynamics (MD) Simulation via Material Studios Accelrys 6.0 to model the Young’s Modulus of Hydrogenated BNNTs. An extrapolation technique was employed to determine the Young’s Modulus due to the deformation of the nanostructure at its theoretical density. A linear regression was used to extrapolate the data to the theoretical density of 2.62g/cm3. Simulation data shows that the hydrogenated BNNTs will experience a 11% decrease in the Young’s Modulus for (6,6) BNNTs and 8.5% decrease for (8,8) BNNTs compared to non-hydrogenated BNNT’s. Hydrogenated BNNTs are a viable option as a nanofiller for radiation shielding nanocomposite materials for long range and long duration space exploration.
Abstract: Ultrafine grained (UFG) and nanostructured (NS) materials have experienced a rapid development during the last decade and made profound impact on every field of materials science and engineering. The present work has been undertaken to develop ultrafine grained pure copper by severe plastic deformation method and to examine the impact property by different characterizing tools.
For this aim, equal channel angular pressing die with the channel angle, outer corner angle and channel diameter of 90°, 17° and 20mm had been designed and manufactured. Commercial pure copper billets were ECAPed up to four passes by route BC at the ambient temperature. The results indicated that there is a great improvement at the hardness measurement, yield strength and ultimate tensile strength after ECAP process. It is found that the magnitudes of HV reach 136HV from 52HV after the final pass. Also, about 285% and 125% enhancement at the YS and UTS values have been obtained after the fourth pass as compared to the as-received conditions, respectively. On the other hand, the elongation to failure and impact energy have been reduced by imposing ECAP process and pass numbers. It is needed to say that about 56% reduction in the impact energy have been attained for the samples as contrasted to annealed specimens.
Abstract: In this work, we have synthesized BaTiO3 via sol gel method by sintering at different temperatures (600, 700, 800, 900, 10000C) and studied their structural, optical and ferroelectric properties through X-ray diffraction (XRD), UV-Vis spectrophotometer and PE Loop Tracer. X-ray diffraction patterns of barium titanate samples show that the peaks of the diffractogram are successfully indexed with the tetragonal and cubic structure of BaTiO3. The Optical band gap calculated through UV Visible spectrophotometer varies from 4.37 to 3.80 eV for the samples sintered at 600 to 10000C, respectively. The particle size calculated through transmission electron microscopy varies from 20 to 40 nm for the samples sintered at 600 to 10000C, respectively. Moreover, it has been observed that the ferroelectricity increases as we increase the sintering temperature.
Abstract: Physical vapor deposition under conditions of an obliquely incident flux results in a film formation with an inclined columnar structure. These columns will be oriented toward the vapor source because of the self-shadowing effect, and they are homogenously distributed on the substrate surface because of the limited surface diffusion ability of ad-atoms when there is no additional substrate heating.
In this work, the oblique angle electron beam evaporation technique is used to fabricate thin films containing inclined nanorods. The results demonstrate that depending on the thin film composition, the morphology of the nanorods is changed as well. The galvanostatic analysis of these thin film anodes reveals that a composite CuSn nanorods having approximately 900mAhg-1 of initial discharge capacity, performs higher electrochemical performance compared to pure Sn nanorods containing anode material. The long cycle life and the advanced electrochemical properties of the nanostructured composite electrode might be attributed to its improved mechanical tolerance and enhanced electrical conductivity depending on the Cu presence in the nanorods.
Abstract: This paper describes the design of new method of
propagation delay measurement in micro and nanostructures during
characterization of ASIC standard library cell. Providing more
accuracy timing information about library cell to the design team we
can improve a quality of timing analysis inside of ASIC design flow
process. Also, this information could be very useful for semiconductor
foundry team to make correction in technology process. By
comparison of the propagation delay in the CMOS element and result
of analog SPICE simulation. It was implemented as digital IP core for
semiconductor manufacturing process. Specialized method helps to
observe the propagation time delay in one element of the standard-cell
library with up-to picoseconds accuracy and less. Thus, the special
useful solutions for VLSI schematic to parameters extraction, basic
cell layout verification, design simulation and verification are
announced.
Abstract: This article reports on the studies of porous GaN prepared by ultra-violet (UV) assisted electrochemical etching in a solution of 4:1:1 HF: CH3OH:H2O2 under illumination of an UV lamp with 500 W power for 10, 25 and 35 minutes. The optical properties of porous GaN sample were compared to the corresponding as grown GaN. Porosity induced photoluminescence (PL) intensity enhancement was found in these samples. The resulting porous GaN displays blue shifted PL spectra compared to the as-grown GaN. Appearance of the blue shifted emission is correlated with the development of highly anisotropic structures in the morphology. An estimate of the size of the GaN nanostructure can be obtained with the help of a quantized state effective mass theory.
Abstract: ZnO nanostructure were synthesized via microwave
method using zinc acetate as starting material, guanidinium as
structure directing agents, and water as solvent.. This work
investigates the photodegradation of azo dyes using the ZnO Flowerlike
in aqueous solutions. As synthesized ZnO samples were
characterized using X-Ray powder diffraction (XRD), scanning
electron microscopy (SEM), and FTIR spectroscopy.In this work
photodecolorization of congored azo dye under UV irradiation by
nano ZnO was studied.
Abstract: The “conveyor belt" as a product represents a
complex high performance component with a wide range of different
applications. Further development of these highly complex
components demands an integration of new technologies and new
enhanced materials. In this context nanostructured fillers appear to
have a more promising effect on the performance of the conveyor
belt composite than conventional micro-scaled fillers.
Within the project “DotTrans" nanostructured fillers, for example
silicon dioxide, are used to optimize performance parameters of
conveyor belt systems. The objective of the project includes
operating parameters like energy consumption or friction
characteristics as well as adaptive parameters like cut or wear
resistance.
Abstract: Two optimized strategies were successfully established
to develop biomolecule-based magnetic nanoassemblies.
Streptavidin-coated and amine-coated magnetic nanoparticles were
chosen as model scaffolds onto which double-stranded DNA and
human immunoglobulin G were specifically conjugated in succession,
using biotin-streptavidin interaction or covalent cross-linkers. The
success of this study opens the prospect of developing selective and
sensitive nanoparticle-based structures for diagnostics or drug
delivery.
Abstract: In this study, ZnO nano rods and ZnO ultrafine particles were synthesized by Gel-casting method. The synthesized ZnO powder has a hexagonal zincite structure. The ZnO aggregates with rod-like morphology are typically 1.4 μm in length and 120 nm in diameter, which consist of many small nanocrystals with diameters of 10 nm. Longer wires connected by many hexahedral ZnO nanocrystals were obtained after calcinations at the temperature over 600° C.The crystalline structures and morphologies of the powder have been characterized by X-ray diffraction(XRD) and Scaning electron microscopy (SEM).The result shows that the different preparation conditions such as concentration H2O, calcinations time and calcinations temperature have a lot of influences upon the properties of nano ZnO powders, an increase in the temperature of the calcinations results in an increase of the grain size and also the increase of the calcinations time in high temperature makes the size of the grains bigger. The existences of extra watter prevent nano grains from improving like rod morphology. We have obtained the smallest grain size of ZnO powder by controlling the process conditions. Finally In a suitable condition, a novel nanostructure, namely bi-rod-like ZnO nano rods was found which is different from known ZnO nanostructures.
Abstract: A major challenge in biomaterials research is the
regulation of protein adsorption which is a key factor for controlling
the subsequent cell adhesion at implant surfaces. The aim of the
present study was to control the adsorption of fibronectin (FN) and
the attachment of MG-63 osteoblasts with an electronic
nanostructure. Shallow doping line lattices with a period of 260 nm
were produced for this purpose by implantation of phosphorous in
silicon wafers. Protein coverage was determined after incubating the
substrate with FN by means of an immunostaining procedure and the
measurement of the fluorescence intensity with a TECAN analyzer.
We observed an increased amount of adsorbed FN on the
nanostructure compared to control substrates. MG-63 osteoblasts
were cultivated for 24h on FN-incubated substrates and their
morphology was assessed by SEM. Preferred orientation and
elongation of the cells in direction of the doping lattice lines was
observed on FN-coated nanostructures.
Abstract: Three dimensional nanostructure materials have attracted the attention of many researches because the possibility to apply them for near future devices in sensors, catalysis and energy related. Tin dioxide is the most used material for gas sensing because its three-dimensional nanostructures and properties are related to the large surface exposed to gas adsorption. We propose the use of branch SnO2 nanowhiskers in interaction with ethanol. All Sn atoms are symmetric. The total energy, potential energy and Kinetic energy calculated for interaction between SnO2 and ethanol in different distances and temperatures. The calculations achieved by methods of Langevin Dynamic and Mont Carlo simulation. The total energy increased with addition ethanol molecules and temperature so interactions between them are endothermic.
Abstract: Noble metal participation in nanostructured
semiconductor catalysts has drawn much interest because of their
improved properties. Recently, it has been discussed by many
researchers that Ag participation in TiO2, CuO, ZnO semiconductors
showed improved photocatalytic and optical properties. In this
research, Ag/ZnO nanocomposite particles were prepared by
Ultrasonic Spray Pyrolysis(USP) Method. 0.1M silver and zinc
nitrate aqueous solutions were used as precursor solutions. The
Ag:Zn atomic ratio of the solution was selected 1:1. Experiments
were taken place under constant air flow of 400 mL/min at 800°C
furnace temperature. Particles were characterized by X-Ray
Diffraction (XRD), Scanning Electron Microscope (SEM) and
Energy Dispersive Spectroscopy (EDS). The crystallite sizes of Ag
and ZnO in composite particles are 24.6 nm, 19.7 nm respectively.
Although, spherical nanocomposite particles are in a range of 300-
800 nm, these particles are formed by the aggregation of primary
particles which are in a range of 20-60 nm.
Abstract: The paper is concerned with the technological process of renovation of shafts used in industrial manufacturing for extruding of sheet material. In the classical renovation technologies, a chrome based coating is applied to the working surface of the shaft in galvanic baths. The process, however, is known to be exclusively harmful due to the waste cyanide products. In this work, we present an advanced nanotechnology based on nonelectric chemical laying of a nickel coating with included nanoparticles. The technology is environmentally harmless and the new coating features an increased hardness and wear resistance. Results from experimental tests of the nanostructured nickel coating are presented and discussed.
Abstract: novel and simple method is introduced for rapid and
highly efficient water treatment by reverse osmosis (RO) method using
multi-walled carbon nanotubes (MWCNTs) / polyacrylonitrile (PAN)
polymer as a flexible, highly efficient, reusable and semi-permeable
mixed matrix membrane (MMM). For this purpose, MWCNTs were
directly synthesized and on-line purified by chemical vapor deposition
(CVD) process, followed by directing the MWCNT bundles towards an
ultrasonic bath, in which PAN polymer was simultaneously suspended
inside a solid porous silica support in water at temperature to ~70 οC.
Fabrication process of MMM was finally completed by hot isostatic
pressing (HIP) process. In accordance with the analytical figures of
merit, the efficiency of fabricated MMM was ~97%. The rate of water
treatment process was also evaluated to 6.35 L min-1. The results reveal
that, the CNT-based MMM is suitable for rapid treatment of different
forms of industrial, sea, drinking and well water samples.
Abstract: Titanium dioxide coatings were deposited by utilizing
atmospheric plasma spraying (APS) system. The agglomerated nanopowder
and different spraying parameters were used to determine
their influences on the microstructure surface feature and photoabsorption
of the coatings. The microstructure of as-sprayed TiO2
coatings were characterized by scanning electron microscope (SEM).
Surface characteristics were investigated by Fourier Transform
Infrared (FT-IR). The photo absorption was determined by UV-VIS
spectrophotometer. It is found that the spray parameters have an
influence on the microstructure, surface feature and photo-absorption
of the TiO2 coatings.
Abstract: Anodizing is an electrochemical process that converts the metal surface into a decorative, durable, corrosion-resistant, anodic oxide finish. Aluminum is ideally suited to anodizing, although other nonferrous metals, such as magnesium and titanium, also can be anodized. The anodic oxide structure originates from the aluminum substrate and is composed entirely of aluminum oxide. This aluminum oxide is not applied to the surface like paint or plating, but is fully integrated with the underlying aluminum substrate, so cannot chip or peel. It has a highly ordered, porous structure that allows for secondary processes such as coloring and sealing. In this experimental paper, we focus on a reliable method for fabricating nanoporous alumina with high regularity. Starting from study of nanostructure materials synthesize methods. After that, porous alumina fabricate in the laboratory by anodization of aluminum oxide. Hard anodization processes are employed to fabricate the nanoporous alumina using 0.3M oxalic acid and 90, 120 and 140 anodized voltages. The nanoporous templates were characterized by SEM and FFT. The nanoporous templates using 140 voltages have high ordered. The pore formation, influence of the experimental conditions on the pore formation, the structural characteristics of the pore and the oxide chemical reactions involved in the pore growth are discuss.
Abstract: In our recent study, we have used ZnO nanoparticles assisted with UV light irradiation to investigate the photocatalytic degradation of Phenol Red (PR). The ZnO photocatalyst was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), specific surface area analysis (BET) and UVvisible spectroscopy. X-ray diffractometry result for the ZnO nanoparticles exhibit normal crystalline phase features. All observed peaks can be indexed to the pure hexagonal wurtzite crystal structures, with the space group of P63mc. There are no other impurities in the diffraction peak. In addition, TEM measurement shows that most of the nanoparticles are rod-like and spherical in shape and fairly monodispersed. A significant degradation of the PR was observed when the catalyst was added into the solution even without the UV light exposure. In addition, the photodegradation increases with the photocatalyst loading. The surface area of the ZnO nanomaterials from the BET measurement was 11.9 m2/g. Besides the photocatalyst loading, the effect of some parameters on the photodegradation efficiency such as initial PR concentration and pH were also studied.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: Composite nanostructures of metal
core/semiconductor shell (Au/CdS) configuration were prepared
using organometalic method. UV-Vis spectra for the Au/CdS colloids
show initially two well separated bands, corresponding to surface
plasmon of the Au core, and the exciton of CdS shell. The absorption
of CdS shell is enhanced, while the Au plasmon band is suppressed
as the shell thickness increases. The shell sizes were estimated from
the optical spectra using the effective mass approximation model
(EMA), and compared to the sizes of the Au core and CdS shell
measured by high resolution transmission electron microscope
(HRTEM). The changes in the absorption features are discussed in
terms of gradual increase in the coupling strength of the Au core
surface plasmon and the exciton in the CdS. leading to charge
transfer and modification of electron oscillation in Au core.