Abstract: In this paper an attempt has been made to correlate the usefulness of electrodes made through powder metallurgy (PM) in comparison with conventional copper electrode during electric discharge machining. Experimental results are presented on electric discharge machining of AISI D2 steel in kerosene with copper tungsten (30% Cu and 70% W) tool electrode made through powder metallurgy (PM) technique and Cu electrode. An L18 (21 37) orthogonal array of Taguchi methodology was used to identify the effect of process input factors (viz. current, duty cycle and flushing pressure) on the output factors {viz. material removal rate (MRR) and surface roughness (SR)}. It was found that CuW electrode (made through PM) gives high surface finish where as the Cu electrode is better for higher material removal rate.
Abstract: In the last few years, three multivariate spectral
analysis techniques namely, Principal Component Analysis (PCA),
Independent Component Analysis (ICA) and Non-negative Matrix
Factorization (NMF) have emerged as effective tools for oscillation
detection and isolation. While the first method is used in determining
the number of oscillatory sources, the latter two methods
are used to identify source signatures by formulating the detection
problem as a source identification problem in the spectral domain.
In this paper, we present a critical drawback of the underlying linear
(mixing) model which strongly limits the ability of the associated
source separation methods to determine the number of sources
and/or identify the physical source signatures. It is shown that the
assumed mixing model is only valid if each unit of the process gives
equal weighting (all-pass filter) to all oscillatory components in its
inputs. This is in contrast to the fact that each unit, in general, acts
as a filter with non-uniform frequency response. Thus, the model
can only facilitate correct identification of a source with a single
frequency component, which is again unrealistic. To overcome
this deficiency, an iterative post-processing algorithm that correctly
identifies the physical source(s) is developed. An additional issue
with the existing methods is that they lack a procedure to pre-screen
non-oscillatory/noisy measurements which obscure the identification
of oscillatory sources. In this regard, a pre-screening procedure
is prescribed based on the notion of sparseness index to eliminate
the noisy and non-oscillatory measurements from the data set used
for analysis.
Abstract: Development of cities and villages, agricultural farms
and industrial regions in abutment and/or in the course of streams and
rivers or in prone flood lands has been caused more notations in
hydrology problems and city planning topics. In order to protection
of cities against of flood damages, embankment construction is a
desired and scientific method. The cities that located in arid zones
may damage by floods periodically. Zavvareh city in Ardestan
township(Isfahan province) with 7704 people located in Ardestan
plain that has been damaged by floods that have flowed from
dominant mountainous watersheds in past years with regard to return
period. In this study, according to flowed floods toward Zavvareh
city, was attempt to plan suitable hydraulic structures such as canals,
bridges and collectors in order to collection, conduction and
depletion of city surface runoff.
Abstract: Knowing the geometrical object pose of products in manufacturing line before robot manipulation is required and less time consuming for overall shape measurement. In order to perform it, the information of shape representation and matching of objects is become required. Objects are compared with its descriptor that conceptually subtracted from each other to form scalar metric. When the metric value is smaller, the object is considered closed to each other. Rotating the object from static pose in some direction introduce the change of value in scalar metric value of boundary information after feature extraction of related object. In this paper, a proposal method for indexing technique for retrieval of 3D geometrical models based on similarity between boundaries shapes in order to measure 3D CAD object pose using object shape feature matching for Computer Aided Testing (CAT) system in production line is proposed. In experimental results shows the effectiveness of proposed method.
Abstract: In this paper, the experimental design of using the
Taguchi method is employed to optimize the processing parameters in
the plasma arc surface hardening process. The processing parameters
evaluated are arc current, scanning velocity and carbon content of
steel. In addition, other significant effects such as the relation between
processing parameters are also investigated. An orthogonal array,
signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are
employed to investigate the effects of these processing parameters.
Through this study, not only the hardened depth increased and surface
roughness improved, but also the parameters that significantly affect
the hardening performance are identified. Experimental results are
provided to verify the effectiveness of this approach.
Abstract: The most Malaria cases are occur along Thai-Mynmar border. Mathematical model for the transmission of Plasmodium falciparum and Plasmodium vivax malaria in a mixed population of Thais and migrant Burmese living along the Thai-Myanmar Border is studied. The population is separated into two groups, Thai and Burmese. Each population is divided into susceptible, infected, dormant and recovered subclasses. The loss of immunity by individuals in the infected class causes them to move back into the susceptible class. The person who is infected with Plasmodium vivax and is a member of the dormant class can relapse back into the infected class. A standard dynamical method is used to analyze the behaviors of the model. Two stable equilibrium states, a disease-free state and an epidemic state, are found to be possible in each population. A disease-free equilibrium state in the Thai population occurs when there are no infected Burmese entering the community. When infected Burmese enter the Thai community, an epidemic state can occur. It is found that the disease-free state is stable when the threshold number is less than one. The epidemic state is stable when a second threshold number is greater than one. Numerical simulations are used to confirm the results of our model.
Abstract: To help the client to select a competent agent
construction enterprise (ACE), this study aims to investigate the
selection standards by using the Fuzzy Analytic Hierarchy Process
(FAHP) and build an evaluation mathematical model with Grey
Relational Analysis (GRA). According to the outputs of literature
review, four orderly levels are established within the model, taking the
consideration of various agent construction models in practice. Then,
the process of applying FAHP and GRA is discussed in detailed.
Finally, through a case study, this paper illustrates how to apply these
methods in getting the weights of each standard and the final
assessment result.
Abstract: The paper makes part from a complex research project
on Romanian Grey Steppe, a unique breed in terms of biological and
cultural-historical importance, on the verge of extinction and which
has been included in a preservation programme of genetic resources
from Romania. The study of genetic polymorphism of protean
fractions, especially kappa-casein, and the genotype relations of
these lactoproteins with some quantitative and qualitative features of
milk yield represents a current theme and a novelty for this breed. In
the estimation of the genetic parameters we used R.E.M.L.
(Restricted Maximum Likelihood) method.
The main lactoprotein from milk, kappa - casein (K-cz),
characterized in the specialized literature as a feature having a high
degree of hereditary transmission, behaves as such in the nucleus under
study, a value also confirmed by the heritability coefficient (h2 = 0.57
%). We must mention the medium values for milk and fat quantity
(h2=0.26, 0.29 %) and the fat and protein percentage from milk
having a high hereditary influence h2 = 0.71 - 0.63 %.
Correlations between kappa-casein and the milk quantity are
negative and strong. Between kappa-casein and other qualitative
features of milk (fat content 0.58-0.67 % and protein content 0.77-
0.87%), there are positive and very strong correlations. At the same
time, between kappa-casein and β casein (β-cz), β lactoglobulin (β-
lg) respectively, correlations are positive having high values (0.37 –
0.45 %), indicating the same causes and determining factors for the
two groups of features.
Abstract: The existence of maximal durations drastically modifies the performance evaluation in Discrete Event Systems (DES). The same particularity may be found on systems where the associated constraints do not concern the time. For example weight measures, in chemical industry, are used in order to control the quantity of consumed raw materials. This parameter also takes a fundamental part in the product quality as the correct transformation process is based upon a given percentage of each essence. Weight regulation therefore increases the global productivity of the system by decreasing the quantity of rejected products. In this paper we present an approach based on mixing different characteristics theories, the fuzzy system and Petri net system to describe the behaviour. An industriel application on a tobacco manufacturing plant, where the critical parameter is the weight is presented as an illustration.
Abstract: The increasing influence of traffic on building
objects and people residing in them should be taken into account in
diagnosis and design. Users of buildings expect that vibrations
occurring in their environment, will not only lead to damage to the
building or its accelerated wear, but neither would affect the required
comfort in rooms designed to accommodate people. This article
describes the methods and principles useful in designing and building
diagnostics located near transportation routes, with particular
emphasis on the impact of traffic vibration on people in buildings. It
also describes the procedures used in obtaining information about the
parameters of vibrations in different cases of diagnostics and design.
A universal algorithm of procedure in diagnostics and design of
buildings taking into account assurance of human vibration comfort
of people residing in the these buildings was presented.
Abstract: Selection of a project among a set of possible
alternatives is a difficult task that the decision maker (DM) has to
face. In this paper, by using a fuzzy TOPSIS technique we propose a
new method for a project selection problem. After reviewing four
common methods of comparing investment alternatives (net present
value, rate of return, benefit cost analysis and payback period) we
use them as criteria in a TOPSIS technique. First we calculate the
weight of each criterion by a pairwise comparison and then we utilize
the improved TOPSIS assessment for the project selection.
Abstract: An original DEA model is to evaluate each DMU
optimistically, but the interval DEA Model proposed in this paper
has been formulated to obtain an efficiency interval consisting of
Evaluations from both the optimistic and the pessimistic view points.
DMUs are improved so that their lower bounds become so large as to
attain the maximum Value one. The points obtained by this method
are called ideal points. Ideal PPS is calculated by ideal of efficiency
DMUs. The purpose of this paper is to rank DMUs by this ideal PPS.
Finally we extend the efficiency interval of a DMU under variable
RTS technology.
Abstract: Fast delay estimation methods, as opposed to
simulation techniques, are needed for incremental performance
driven layout synthesis. On-chip inductive effects are becoming
predominant in deep submicron interconnects due to increasing clock
speed and circuit complexity. Inductance causes noise in signal
waveforms, which can adversely affect the performance of the circuit
and signal integrity. Several approaches have been put forward which
consider the inductance for on-chip interconnect modelling. But for
even much higher frequency, of the order of few GHz, the shunt
dielectric lossy component has become comparable to that of other
electrical parameters for high speed VLSI design. In order to cope up
with this effect, on-chip interconnect has to be modelled as
distributed RLCG line. Elmore delay based methods, although
efficient, cannot accurately estimate the delay for RLCG interconnect
line. In this paper, an accurate analytical delay model has been
derived, based on first and second moments of RLCG
interconnection lines. The proposed model considers both the effect
of inductance and conductance matrices. We have performed the
simulation in 0.18μm technology node and an error of as low as less
as 5% has been achieved with the proposed model when compared to
SPICE. The importance of the conductance matrices in interconnect
modelling has also been discussed and it is shown that if G is
neglected for interconnect line modelling, then it will result an delay
error of as high as 6% when compared to SPICE.
Abstract: In the past decade, because of wide applications of
hybrid systems, many researchers have considered modeling and
control of these systems. Since switching systems constitute an
important class of hybrid systems, in this paper a method for optimal
control of linear switching systems is described. The method is also
applied on the two-tank system which is a much appropriate system
to analyze different modeling and control techniques of hybrid
systems. Simulation results show that, in this method, the goals of
control and also problem constraints can be satisfied by an
appropriate selection of cost function.
Abstract: This paper investigates the inverse problem of determining
the unknown time-dependent leading coefficient in the parabolic
equation using the usual conditions of the direct problem and an additional
condition. An algorithm is developed for solving numerically
the inverse problem using the technique of space decomposition in a
reproducing kernel space. The leading coefficients can be solved by a
lower triangular linear system. Numerical experiments are presented
to show the efficiency of the proposed methods.
Abstract: The morphological parameter of a thin film surface
can be characterized by power spectral density (PSD) functions
which provides a better description to the topography than the RMS
roughness and imparts several useful information of the surface
including fractal and superstructure contributions. Through the
present study Nanoparticle copper/carbon composite films were
prepared by co-deposition of RF-Sputtering and RF-PECVD method
from acetylene gas and copper target. Surface morphology of thin
films is characterized by using atomic force microscopy (AFM). The
Carbon content of our films was obtained by Rutherford Back
Scattering (RBS) and it varied from .4% to 78%. The power values of
power spectral density (PSD) for the AFM data were determined by
the fast Fourier transform (FFT) algorithms. We investigate the effect
of carbon on the roughness of thin films surface. Using such
information, roughness contributions of the surface have been
successfully extracted.