Abstract: This work presents a fusion of Log Gabor Wavelet
(LGW) and Maximum a Posteriori (MAP) estimator as a speech
enhancement tool for acoustical background noise reduction. The
probability density function (pdf) of the speech spectral amplitude is
approximated by a Generalized Laplacian Distribution (GLD).
Compared to earlier estimators the proposed method estimates the
underlying statistical model more accurately by appropriately
choosing the model parameters of GLD. Experimental results show
that the proposed estimator yields a higher improvement in
Segmental Signal-to-Noise Ratio (S-SNR) and lower Log-Spectral
Distortion (LSD) in two different noisy environments compared to
other estimators.
Abstract: Accident in spent fuel pool (SFP) of Fukushima
Daiichi Unit 4 showed the importance of continuous monitoring of the
key environmental parameters such as water temperature, water level,
and radiation level in the SFP at accident conditions. Because the SFP
water temperature is one of the key parameters indicating SFP
conditions, its behavior at accident conditions shall be understood to
prepare appropriate measures. This study estimated temporal change
in the SFP water temperature at Kori Unit 1 with 587 MWe for 1 hour
after initiation of a loss-of-pool-cooling accident. For the estimation,
ANSYS CFX 13.0 code was used. The estimation showed that the
increasing rate of the water temperature was 3.90C per hour and the
SFP water temperature could reach 1000C in 25.6 hours after the
initiation of loss-of-pool-cooling accident.
Abstract: In this work, we analyze the deformation of surface
waves in shallow flows conditions, propagating in a channel of
slowly varying cross-section. Based on a singular perturbation
technique, the main purpose is to predict the motion of waves by
using a dimensionless formulation of the governing equations,
considering that the longitudinal variation of the transversal section
obey a power-law distribution. We show that the spatial distribution
of the waves in the varying cross-section is a function of a kinematic
parameter,κ , and two geometrical parameters εh
and w ε . The above
spatial behavior of the surface elevation is modeled by an ordinary
differential equation. The use of single formulas to model the varying
cross sections or transitions considered in this work can be a useful
approximation to natural or artificial geometrical configurations.
Abstract: The primary cause of Total Hip Replacement (THR)
failure for younger patients is aseptic loosening. This complication is
twice more likely to happen in acetabular cup than in femoral stem.
Excessive micromotion between bone and implant will cause
loosening and it depends in patient activities, age and bone. In this
project, the effects of different metal back design of press fit on
osseointegration of the acetabular cup are carried out. Commercial
acetabular cup designs, namely Spiked, Superfix and Quadrafix are
modelled and analyzed using commercial finite element software.
The diameter of acetabular cup is based on the diameter of acetabular
rim to make sure the component fit to the acetabular cavity. A new
design of acetabular cup are proposed and analyzed to get better
osseointegration between the bones and implant interface. Results
shows that the proposed acetabular cup designs are more stable
compared to other designs with respect to stress and displacement
aspects.
Abstract: The aim of current study was to investigate the
changes in the quality parameters of Holstein bull semen during the
heat stress and the effect of feeding a source of omega-3 fatty acids
in this period. Samples were obtained from 19 Holstein bulls during
the expected time of heat stress in Iran (June to September 2009).
Control group (n=10) were fed a standard concentrate feed while
treatment group (n=9) had this feed top dressed with 100 g of an
omega-3 enriched nutriceutical. Semen quality was assessed on
ejaculates collected after 1, 5, 9 and 12 weeks of supplementation.
Computer-assisted assessment of sperm motility, viability (eosinnigrosin)
and hypo-osmotic swelling test (HOST) were conducted.
Heat stress affected sperm quality parameters by week 5 and 9
(p
Abstract: In this paper, we consider the effect of the initial
sample size on the performance of a sequential approach that used
in selecting a good enough simulated system, when the number
of alternatives is very large. We implement a sequential approach
on M=M=1 queuing system under some parameter settings, with a
different choice of the initial sample sizes to explore the impacts on
the performance of this approach. The results show that the choice
of the initial sample size does affect the performance of our selection
approach.
Abstract: This paper presents a hybrid fuzzy-PD plus PID
(HFPP) controller and its application to steam distillation process for
essential oil extraction system. Steam temperature is one of the most
significant parameters that can influence the composition of essential
oil yield. Due to parameter variations and changes in operation
conditions during distillation, a robust steam temperature controller becomes nontrivial to avoid the degradation of essential oil quality.
Initially, the PRBS input is triggered to the system and output of steam temperature is modeled using ARX model structure. The
parameter estimation and tuning method is adopted by simulation
using HFPP controller scheme. The effectiveness and robustness of
proposed controller technique is validated by real time
implementation to the system. The performance of HFPP using 25 and 49 fuzzy rules is compared. The experimental result demonstrates the proposed HFPP using 49 fuzzy rules achieves a
better, consistent and robust controller compared to PID when considering the test on tracking the set point and the effects due to disturbance.
Abstract: In this study, a longitudinal joint connection was
proposed for the short-span slab-type modular bridges with rapid
construction. The slab-type modular bridge consists of a number of
precast slab modules and has the joint connection between the
modules in the longitudinal direction of the bridge. A finite element
based parameter analysis was conducted to design the shape and the
dimensions of the longitudinal joint connection. Numbers of shear
keys within the joint, height and depth of the shear key, tooth angle,
and the spacing were considered as the design parameters. Using the
local cracking load at the corner of the shear key and the
cross-sectional area of the joint, an efficiency factor was proposed to
evaluate the effectiveness of the longitudinal joint connection. The
dimensions of shear key were determined by comparing the cracking
loads and the efficiency factors obtained from the finite element
analysis.
Abstract: An interesting method to produce calcium carbonate is based in a gas-liquid reaction between carbon dioxide and aqueous solutions of calcium hydroxide. The design parameters for gas-liquid phase are flow regime, individual mass transfer, gas-liquid specific interfacial area. Most studies on gas-liquid phase were devoted to the experimental determination of some of these parameters, and more specifically, of the mass transfer coefficient, kLa which depends fundamentally on the superficial gas velocity and on the physical properties of absorption phase. The principle investigation was directed to study the effect of the vibration on the mass transfer coefficient kLa in gas-liquid phase during absorption of CO2 in the in aqueous solution of calcium hydroxide. The vibration with a higher frequency increase the mass transfer coefficient kLa, but vibration with lower frequency didn-t improve it, the mass transfer coefficient kLa increase with increase the superficial gas velocity.
Abstract: PDMS (Polydimethylsiloxane) polymer is a suitable material for biological and MEMS (Microelectromechanical systems) designers, because of its biocompatibility, transparency and high resistance under plasma treatment. PDMS round channel is always been of great interest due to its ability to confine the liquid with membrane type micro valves. In this paper we are presenting a very simple way to form round shapemicrofluidic channel, which is based on reflow of positive photoresist AZ® 40 XT. With this method, it is possible to obtain channel of different height simply by varying the spin coating parameters of photoresist.
Abstract: Studies on Simultaneous Saccharification and Fermentation (SSF) of corn flour, a major agricultural product as the substrate using starch digesting glucoamylase enzyme derived from Aspergillus niger and non starch digesting and sugar fermenting Saccharomyces cerevisiae in a batch fermentation. Experiments based on Central Composite Design (CCD) were conducted to study the effect of substrate concentration, pH, temperature, enzyme concentration on Ethanol Concentration and the above parameters were optimized using Response Surface Methodology (RSM). The optimum values of substrate concentration, pH, temperature and enzyme concentration were found to be 160 g/l, 5.5, 30°C and 50 IU respectively. The effect of inoculums age on ethanol concentration was also investigated. The corn flour solution equivalent to 16% initial starch concentration gave the highest ethanol concentration of 63.04 g/l after 48 h of fermentation at optimum conditions of pH and temperature. Monod model and Logistic model were used for growth kinetics and Leudeking – Piret model was used for product formation kinetics.
Abstract: In order to study pressed pile test and ultimate bearing
capacity character of large-diameter steel pipe pile, based on two high-piled wharfs of Zhanjiang Port, pressed pile test and numerical simulation of three large-diameter steel pipe piles are analyzed in this
paper. Anchored pile method is used to pressed pile test, and the
curves of Q-s and ultimate bearing capacity are attained. Then the three piles are numerically simulated by ABAQUS, and results of numerical simulation and those of field test are comparatively analyzed. The results show that settlement value of numerical
simulation is larger than that of field test in the process of loading, the difference value is widening with the increasing of load, and the
ultimate difference value of settlement is 20% to 30%.
Abstract: The influence of viscosity on droplet diameter for
water-in-crude oil (w/o) emulsion with two different ratios; 20-80 %
and 50-50 % w/o emulsion was examined in the Brookfield
Rotational Digital Rheometer. The emulsion was prepared with
sorbitan sesquiolate (Span 83) act as emulsifier at varied temperature
and stirring speed in rotation per minute (rpm). Results showed that
the viscosity of w/o emulsion was strongly augmented by increasing
volume of water and decreased the temperature. The changing of
viscosity also altered the droplet size distribution. Changing of
droplet diameter was depends on the viscosity and the behavior of
emulsion either Newtonian or non-Newtonian.
Abstract: Exclusive breastfeeding is the feeding of a baby on no other milk apart from breast milk. Exclusive breastfeeding during the first 6 months of life is of fundamental importance because it supports optimal growth and development during infancy and reduces the risk of obliterating diseases and problems. Moreover, in developed countries, exclusive breastfeeding has decreased the incidence and/or severity of diarrhea, lower respiratory infection and urinary tract infection. In this paper, we study the factors that influence exclusive breastfeeding and use the Generalized Poisson regression model to analyze the practices of exclusive breastfeeding in Mauritius. We develop two sets of quasi-likelihood equations (QLE)to estimate the parameters.
Abstract: The present paper considers the steady free convection
boundary layer flow of a viscoelastic fluid on solid sphere with
Newtonian heating. The boundary layer equations are an order higher
than those for the Newtonian (viscous) fluid and the adherence
boundary conditions are insufficient to determine the solution of
these equations completely. Thus, the augmentation an extra
boundary condition is needed to perform the numerical
computational. The governing boundary layer equations are first
transformed into non-dimensional form by using special
dimensionless group and then solved by using an implicit finite
difference scheme. The results are displayed graphically to illustrate
the influence of viscoelastic K and Prandtl Number Pr parameters on
skin friction, heat transfer, velocity profiles and temperature profiles.
Present results are compared with the published papers and are found
to concur very well.
Abstract: In this paper, the full state feedback controllers
capable of regulating and tracking the speed trajectory are presented.
A fourth order nonlinear mean value model of a 448 kW turbocharged
diesel engine published earlier is used for the purpose.
For designing controllers, the nonlinear model is linearized and
represented in state-space form. Full state feedback controllers
capable of meeting varying speed demands of drivers are presented.
Main focus here is to investigate sensitivity of the controller to the
perturbations in the parameters of the original nonlinear model.
Suggested controller is shown to be highly insensitive to the
parameter variations. This indicates that the controller is likely
perform with same accuracy even after significant wear and tear of
engine due to its use for years.
Abstract: This article presents the simulation, parameterization and optimization of an electromagnet with the C–shaped configuration, intended for the study of magnetic properties of materials. The electromagnet studied consists of a C-shaped yoke, which provides self–shielding for minimizing losses of magnetic flux density, two poles of high magnetic permeability and power coils wound on the poles. The main physical variable studied was the static magnetic flux density in a column within the gap between the poles, with 4cm2 of square cross section and a length of 5cm, seeking a suitable set of parameters that allow us to achieve a uniform magnetic flux density of 1x104 Gaussor values above this in the column, when the system operates at room temperature and with a current consumption not exceeding 5A. By means of a magnetostatic analysis by the finite element method, the magnetic flux density and the distribution of the magnetic field lines were visualized and quantified. From the results obtained by simulating an initial configuration of electromagnet, a structural optimization of the geometry of the adjustable caps for the ends of the poles was performed. The magnetic permeability effect of the soft magnetic materials used in the poles system, such as low– carbon steel (0.08% C), Permalloy (45% Ni, 54.7% Fe) and Mumetal (21.2% Fe, 78.5% Ni), was also evaluated. The intensity and uniformity of the magnetic field in the gap showed a high dependence with the factors described above. The magnetic field achieved in the column was uniform and its magnitude ranged between 1.5x104 Gauss and 1.9x104 Gauss according to the material of the pole used, with the possibility of increasing the magnetic field by choosing a suitable geometry of the cap, introducing a cooling system for the coils and adjusting the spacing between the poles. This makes the device a versatile and scalable tool to generate the magnetic field necessary to perform magnetic characterization of materials by techniques such as vibrating sample magnetometry (VSM), Hall-effect, Kerr-effect magnetometry, among others. Additionally, a CAD design of the modules of the electromagnet is presented in order to facilitate the construction and scaling of the physical device.
Abstract: Border Gateway Protocol (BGP) is the standard routing protocol between various autonomous systems (AS) in the internet. In the event of failure, a considerable delay in the BGP convergence has been shown by empirical measurements. During the convergence time the BGP will repeatedly advertise new routes to some destination and withdraw old ones until it reach a stable state. It has been found that the KEEPALIVE message timer and the HOLD time are tow parameters affecting the convergence speed. This paper aims to find the optimum value for the KEEPALIVE timer and the HOLD time that maximally reduces the convergence time without increasing the traffic. The KEEPALIVE message timer optimal value founded by this paper is 30 second instead of 60 seconds, and the optimal value for the HOLD time is 90 seconds instead of 180 seconds.
Abstract: This paper describes an algorithm to estimate realtime vehicle velocity using image processing technique from the known camera calibration parameters. The presented algorithm involves several main steps. First, the moving object is extracted by utilizing frame differencing technique. Second, the object tracking method is applied and the speed is estimated based on the displacement of the object-s centroid. Several assumptions are listed to simplify the transformation of 2D images from 3D real-world images. The results obtained from the experiment have been compared to the estimated ground truth. From this experiment, it exhibits that the proposed algorithm has achieved the velocity accuracy estimation of about ± 1.7 km/h.
Abstract: Avalanche velocity (from start to track zone) has been estimated in the present model for an avalanche which is triggered artificially by an explosive devise. The initial development of the model has been from the concept of micro-continuum theories [1], underwater explosions [2] and from fracture mechanics [3] with appropriate changes to the present model. The model has been computed for different slab depth R, slope angle θ, snow density ¤ü, viscosity μ, eddy viscosity η*and couple stress parameter η. The applicability of the present model in the avalanche forecasting has been highlighted.