Abstract: Primary and secondary data from the Bauchi abattoir were utilized to determine the relative contributions of different livestock species to meat supply in Bauchi Metropolis. Daily livestock slaughter figures for five months (June – October 2011) indicated that more goats (64.0) were slaughtered than either sheep (47.3) or cattle (41.30) each day (P
Abstract: Three sulphonic acid-doped polyanilines were
synthesized through chemical oxidation at low temperature (0-5 oC)
and potential of these polymers as sensing agent for O2 gas detection
in terms of fluorescence quenching was studied. Sulphuric acid,
dodecylbenzene sulphonic acid (DBSA) and camphor sulphonic acid
(CSA) were used as doping agents. All polymers obtained were dark
green powder. Polymers obtained were characterized by Fourier
transform infrared spectroscopy, ultraviolet-visible absorption
spectroscopy, thermogravimetry analysis, elemental analysis,
differential scanning calorimeter and gel permeation
chromatography. Characterizations carried out showed that polymers
were successfully synthesized with mass recovery for sulphuric aciddoped
polyaniline (SPAN), DBSA-doped polyaniline (DBSA-doped
PANI) and CSA-doped polyaniline (CSA-doped PANI) of 71.40%,
75.00% and 39.96%, respectively. Doping level of SPAN, DBSAdoped
PANI and CSA-doped PANI were 32.86%, 33.13% and
53.96%, respectively as determined based on elemental analysis.
Sensing test was carried out on polymer sample in the form of
solution and film by using fluorescence spectrophotometer. Samples
of polymer solution and polymer film showed positive response
towards O2 exposure. All polymer solutions and films were fully
regenerated by using N2 gas within 1 hour period. Photostability
study showed that all samples of polymer solutions and films were
stable towards light when continuously exposed to xenon lamp for 9
hours. The relative standard deviation (RSD) values for SPAN
solution, DBSA-doped PANI solution and CSA-doped PANI
solution for repeatability were 0.23%, 0.64% and 0.76%,
respectively. Meanwhile RSD values for reproducibility were 2.36%,
6.98% and 1.27%, respectively. Results for SPAN film, DBSAdoped
PANI film and CSA-doped PANI film showed the same
pattern with RSD values for repeatability of 0.52%, 4.05% and
0.90%, respectively. Meanwhile RSD values for reproducibility were
2.91%, 10.05% and 7.42%, respectively. The study on effect of the
flow rate on response time was carried out using 3 different rates
which were 0.25 mL/s, 1.00 mL/s and 2.00 mL/s. Results obtained
showed that the higher the flow rate, the shorter the response time.
Abstract: A combination of image fusion and quad tree decomposition method is used for detecting the sunspot trajectories in each month and computation of the latitudes of these trajectories in each solar hemisphere. Daily solar images taken with SOHO satellite are fused for each month and the result of fused image is decomposed with Quad Tree decomposition method in order to classifying the sunspot trajectories and then to achieve the precise information about latitudes of sunspot trajectories. Also with fusion we deduce some physical remarkable conclusions about sun magnetic fields behavior. Using quad tree decomposition we give information about the region on sun surface and the space angle that tremendous flares and hot plasma gases permeate interplanetary space and attack to satellites and human technical systems. Here sunspot images in June, July and August 2001 are used for studying and give a method to compute the latitude of sunspot trajectories in each month with sunspot images.
Abstract: The objective of this study was to develop and compare alternative prediction equations of lean meat proportion (LMP) of lamb carcasses. Forty (40) male lambs, 22 of Churra Galega Bragançana Portuguese local breed and 18 of Suffolk breed were used. Lambs were slaughtered, and carcasses weighed approximately 30 min later in order to obtain hot carcass weight (HCW). After cooling at 4º C for 24-h a set of seventeen carcass measurements was recorded. The left side of carcasses was dissected into muscle, subcutaneous fat, inter-muscular fat, bone, and remainder (major blood vessels, ligaments, tendons, and thick connective tissue sheets associated with muscles), and the LMP was evaluated as the dissected muscle percentage. Prediction equations of LMP were developed, and fitting quality was evaluated through the coefficient of determination of estimation (R2 e) and standard error of estimate (SEE). Models validation was performed by k-fold crossvalidation and the coefficient of determination of prediction (R2 p) and standard error of prediction (SEP) were computed. The BT2 measurement was the best single predictor and accounted for 37.8% of the LMP variation with a SEP of 2.30%. The prediction of LMP of lamb carcasses can be based simple models, using as predictors the HCW and one fat thickness measurement.
Abstract: White scar oyster (Crassostrea belcheri) is often eaten
raw and being the leading vehicle for foodborne disease, especially
Salmonella Weltevreden which exposed the prominent and most
resistant to radiation. Gamma irradiation at a low dose of 1 kGy was
enough to eliminate S. Weltevreden contaminated in oyster meat at a
level up to 5 log CFU/g while it still retain the raw characteristics and
equivalent sensory quality as the non-irradiated one. Process
development of ready-to-eat chilled oyster meat was conducted by
shucking the meat, individually packed in plastic bags, subjected to 1
kGy gamma radiation at chilled condition and then stored in 4oC
refrigerated temperature. Microbiological determination showed the
absence of S. Weltevreden (5 log CFU/g initial inoculated) along the
whole storage time of 30 days. Sensory evaluation indicated the
decreasing in sensory scores along storage time which determining
the product shelf life to be 18 days compared to 15 days of nonirradiated
one. The most advantage of developed process was to
provide the safe raw oyster to consumers and in addition sensory
quality retained and 3-day extension shelf life also exist.
Abstract: The objective of the present study was to evaluate the
potential of hollow microneedles for enhancing the transdermal
delivery of Bovine Serum Albumin (MW~66,000 Da)-Fluorescein
Isothiocyanate (BSA-FITC) conjugate, a hydrophilic large molecular
compound. Moreover, the effect of different formulations was
evaluated. The series of binary mixtures composed of propylene
glycol (PG) and pH 7.4 phosphate buffer solution (PBS) was
prepared and used as a medium for BSA-FITC. The results showed
that there was no permeation of BSA-FITC solution across the
neonatal porcine skin without using hollow microneedles, whereas
the cumulative amount of BSA-FITC released at 8 h through the
neonatal porcine skin was about 60-70% when using hollow
microneedles. Furthermore, the results demonstrated that the higher
volume of PG in binary mixtures injected, the lower cumulative
amount of BSA-FITC released and release rate of BSA-FITC from
skin. These release profiles of BSA-FITC in binary mixtures were
expressed by Fick-s law of diffusion. These results suggest the
utilization of hollow microneedle to enhance transdermal delivery of
protein and provide useful information for designing an effective
hollow microneedle system.
Abstract: Five lignin samples were fractionated with
Acetone/Water mixtures and the obtained fractions were subjected to
extensive structural characterization, including Fourier Transform
Infrared (FT-IR), Gel permeation Chromatography (GPC) and
Phosphorus-31 NMR spectroscopy (31P-NMR). The results showed
that for all studied lignins the solubility increases with the increment
of the acetone concentration. Wheat straw lignin has the highest
solubility in 90/10 (v/v) Acetone/Water mixture, 400 mg lignin being
dissolved in 1 mL mixture. The weight average molecular weight of
the obtained fractions increased with the increment of acetone
concentration and thus with solubility. 31P-NMR analysis based on
lignin modification by reactive phospholane into phosphitylated
compounds was used to differentiate and quantify the different types
of OH groups (aromatic, aliphatic, and carboxylic) found in the
fractions obtained with 70/30 (v/v) Acetone/Water mixture.
Abstract: In this paper, removal of chromium(VI) from aqueous
solution has been researched using reverse osmosis. The influence of
transmembrane pressure and feed concentration on permeate flux,
water recovery, permeate concentration, and salt rejection was
studied. The results showed that according to the variation of
transmembrane pressure and feed concentration, the permeate flux
and salt rejection were in the range 19.17 to 58.75 l/m2.min and
99.51 to 99.8 %, respectively. The highest permeate flux, 58.75
l/m2.min, and water recovery, 42.47 %, were obtained in the highest
pressure and the lowest feed concentration. On the other hand, the
lowest permeate concentration, 0.01 mg/l, and the highest salt
rejection, 99.8 %, were obtained in the highest pressure and the
lowest feed concentration.
Abstract: An immunomodulator bioproduct is prepared in a
batch bioprocess with a modified bacterium Pseudomonas
aeruginosa. The bioprocess is performed in 100 L Bioengineering
bioreactor with 42 L cultivation medium made of peptone, meat
extract and sodium chloride. The optimal bioprocess parameters were
determined: temperature – 37 0C, agitation speed - 300 rpm, aeration
rate – 40 L/min, pressure – 0.5 bar, Dow Corning Antifoam M-max.
4 % of the medium volume, duration - 6 hours. This kind of
bioprocesses are appreciated as difficult to control because their
dynamic behavior is highly nonlinear and time varying. The aim of
the paper is to present (by comparison) different models based on
experimental data.
The analysis criteria were modeling error and convergence rate.
The estimated values and the modeling analysis were done by using
the Table Curve 2D.
The preliminary conclusions indicate Andrews-s model with a
maximum specific growth rate of the bacterium in the range of
0.8 h-1.
Abstract: The increasing usage of antibiotics in the animal
farming industry is an emerging worldwide problem contributing to
the development of antibiotic resistance. The purpose of this work was
to investigate the prevalence and antibiotic resistance profile of
bacterial isolates collected from aquatic environments and meats in a
peri-urban community in Daejeon, Korea. In an antibacterial
susceptibility test, the bacterial isolates showed a high incidence of
resistance (~ 26.04 %) to cefazolin, tetracycline, gentamycin,
norfloxacin, erythromycin and vancomycin. The results from a test for
multiple antibiotic resistance indicated that the isolates were
displaying an approximately 5-fold increase in the incidence of
multiple antibiotic resistance to combinations of two different
antibiotics compared to combinations of three or more antibiotics.
Most of the isolates showed multi-antibiotic resistance, and the
resistance patterns were similar among the sampling groups.
Sequencing data analysis of 16S rRNA showed that most of the
resistant isolates appeared to be dominated by the classes
Betaproteobacteria and Gammaproteobacteria in the phylum
Proteobacteria.
Abstract: Compacted clay liners (CCLs) are the main materials
used in waste disposal landfills due to their low permeability. In this
study, the effect on the shear resistant of clays with inorganic salt
solutions as permeate fluid was experimentally investigated. For this
purpose, NaCl inorganic salt solution at concentrations of 2, 5, 10%
and deionized water were used. Laboratory direct shear and Vane
shear tests were conducted on three compacted clays with low,
medium and high plasticity. Results indicated that the solutions type
and its concentration affect the shear properties of the mixture. In the
light of this study, the influence magnitude of these inorganic salts in
varies concentrations in different clays were determined and more
suitable compacted clay with the compare of plasticity were found.
Abstract: In this work Membrane Distillation is applied to
concentrate orange Juice. Clarified orange juice (11o Brix) obtained
from fresh fruits and a sugar solution was subjected to membrane
distillation. The experiments were performed on a flat sheet module
using orange juice and sucrose solution as feeds. The concentration
of a sucrose solution, used as a model fruit juice and also orange
juice, was carried out in a direct contact membrane distillation using
hydrophobic PTFE membrane of pore size 0.2 μm and porosity 70%.
Surface modification of PTFE membrane has been carried out by
treating membrane with alcohol and water solution to make it
hydrophilic and then hydrophobicity was regained by drying. The
influences of the feed temperature, feed concentration, flow rate,
operating time on the permeate flux were studied for treated and non
treated membrane. In this work treated and non treated membrane
were compared in terms of water flux, Within the tested range, MD
with surface modified membrane the water flux has been
significantly improved by treating the membrane surface.
Abstract: Flour from Mucuna beans (Mucuna pruriens) were
used in producing texturized meat analogue using a single screw
extruder to monitor modifications on the proximate composition and
the functional properties at high moisture level. Response surface
methodology based on Box Behnken design at three levels of barrel
temperature (110, 120, 130°C), screw speed (100,120,140rpm) and
feed moisture (44, 47, 50%) were used in 17 runs. Regression models
describing the effect of variables on the product responses were
obtained. Descriptive profile analyses and consumer acceptability
test were carried out on optimized flavoured extruded meat analogue.
Responses were mostly affected by barrel temperature and moisture
level and to a lesser extent by screw speed. Optimization results
based on desirability concept indicated that a barrel temperature of
120.15°C, feed moisture of 47% and screw speed of 119.19 rpm
would produce meat analogue of preferable proximate composition,
functional and sensory properties which reveals consumers` likeness
for the product.
Abstract: Enhancement of the performance of a reverse osmosis
(RO) unit through periodic control is studied. The periodic control
manipulates the feed pressure and flow rate of the RO unit. To ensure
the periodic behavior of the inputs, the manipulated variables (MV)
are transformed into the form of sinusoidal functions. In this case, the
amplitude and period of the sinusoidal functions become the
surrogate MV and are thus regulated via nonlinear model predictive
control algorithm. The simulation results indicated that the control
system can generate cyclic inputs necessary to enhance the closedloop
performance in the sense of increasing the permeate production
and lowering the salt concentration. The proposed control system can
attain its objective with arbitrary set point for the controlled outputs.
Successful results were also obtained in the presence of modeling
errors.
Abstract: This study presents the performance of membrane
bioreactor in treating high phosphate wastewater. The laboratory
scale MBR was operated at permeate flux of 25 L/m2.h with a hollow
fiber membrane (polypropylene, approx. pore size 0.01 - 0.2 μm) at
hydraulic retention time (HRT) of 12 hrs. Scanning electron
microscopy (SEM) and energy diffusive X-ray (EDX) analyzer were
used to characterize the membrane foulants. Results showed that the
removal efficiencies of COD, TSS, NH3-N and PO4
3- were 93, 98, 80
and 30% respectively. On average 91% of influent soluble microbial
products (SMP) were eliminated, with the eliminations of
polysaccharides mostly above 80%. The main fouling resistance was
cake resistance. It should be noted that SMP were found in major
portions of mixed liquor that played a relatively significant role in
membrane fouling. SEM and EDX analyses indicated that the
foulants covering the membrane surfaces comprises not only organic
substances but also inorganic elements including Mg, Ca, Al, K and
P.
Abstract: The importance of ensuring safe meat handling and
processing practices has been demonstrated in global reports on food
safety scares and related illness and deaths. This necessitated stricter
meat safety control strategies. Today, many countries have regulated
towards preventative and systematic control over safe meat
processing at abattoirs utilizing the Hazard Analysis Critical Control
Point (HACCP) principles. HACCP systems have been reported as
effective in managing food safety risks, if correctly implemented.
South Africa has regulated the Hygiene Management System (HMS)
based on HACCP principles applicable to abattoirs. Regulators utilise
the Hygiene Assessment System (HAS) to audit compliance at
abattoirs. These systems were benchmarked from the United
Kingdom (UK). Little research has been done them since inception as
of 2004. This paper presents a review of the two systems, its
implementation and comparison with HACCP. Recommendations are
made for future research to demonstrate the utility of the HMS and
HAS in assuring safe meat to consumers.