Abstract: In this paper, the bio-mechanical analysis of human joints is carried out and the study is extended to the robot manipulator. This study will first focus on the kinematics of human arm which include the movement of each joint in shoulder, wrist, elbow and finger complexes. Those analyses are then extended to the design of a human robot manipulator. A simulator is built for Direct Kinematics and Inverse Kinematics of human arm. In the simulation of Direct Kinematics, the human joint angles can be inserted, while the position and orientation of each finger tips (end-effector) are shown. Inverse Kinematics does the reverse of the Direct Kinematics. Based on previous materials obtained from kinematics analysis, the human manipulator joints can be designed to follow prescribed position trajectories.
Abstract: Young patients suffering from Cerebral Palsy are
facing difficult choices concerning heavy surgeries. Diagnosis settled
by surgeons can be complex and on the other hand decision for
patient about getting or not such a surgery involves important
reflection effort. Proposed software combining prediction for
surgeries and post surgery kinematic values, and from 3D model
representing the patient is an innovative tool helpful for both patients
and medicine professionals. Beginning with analysis and
classification of kinematics values from Data Base extracted from
gait analysis in 3 separated clusters, it is possible to determine close
similarity between patients. Prediction surgery best adapted to
improve a patient gait is then determined by operating a suitable
preconditioned neural network. Finally, patient 3D modeling based
on kinematic values analysis, is animated thanks to post surgery
kinematic vectors characterizing the closest patient selected from
patients clustering.
Abstract: This paper presents the development of a software
application for Off-line robot task programming and simulation. Such
application is designed to assist in robot task planning and to direct
manipulator motion on sensor based programmed motion. The
concept of the designed programming application is to use the power
of the knowledge base for task accumulation. In support of the
programming means, an interactive graphical simulation for
manipulator kinematics was also developed and integrated into the
application as the complimentary factor to the robot programming
media. The simulation provides the designer with useful,
inexpensive, off-line tools for retain and testing robotics work cells
and automated assembly lines for various industrial applications.
Abstract: The kinematics of manipulators is a central problem in the automatic control of robot manipulators. Theoretical background for the analysis of the 5 Dof Lynx-6 educational Robot Arm kinematics is presented in this paper. The kinematics problem is defined as the transformation from the Cartesian space to the joint space and vice versa. The Denavit-Harbenterg (D-H) model of representation is used to model robot links and joints in this study. Both forward and inverse kinematics solutions for this educational manipulator are presented, An effective method is suggested to decrease multiple solutions in inverse kinematics. A visual software package, named MSG, is also developed for testing Motional Characteristics of the Lynx-6 Robot arm. The kinematics solutions of the software package were found to be identical with the robot arm-s physical motional behaviors.
Abstract: This paper will provide the kinematic and dynamic
analysis of a lower limb exoskeleton. The forward and inverse
kinematics of proposed exoskeleton is performed using Denevit and
Hartenberg method. The torques required for the actuators will be
calculated using Lagrangian formulation technique. This research can
be used to design the control of the proposed exoskeleton.
Abstract: In this work, are discussed two formulations of the boundary element method - BEM to perform linear bending analysis of plates reinforced by beams. Both formulations are based on the Kirchhoff's hypothesis and they are obtained from the reciprocity theorem applied to zoned plates, where each sub-region defines a beam or a slab. In the first model the problem values are defined along the interfaces and the external boundary. Then, in order to reduce the number of degrees of freedom kinematics hypothesis are assumed along the beam cross section, leading to a second formulation where the collocation points are defined along the beam skeleton, instead of being placed on interfaces. On these formulations no approximation of the generalized forces along the interface is required. Moreover, compatibility and equilibrium conditions along the interface are automatically imposed by the integral equation. Thus, these formulations require less approximation and the total number of the degree s of freedom is reduced. In the numerical examples are discussed the differences between these two BEM formulations, comparing as well the results to a well-known finite element code.
Abstract: This paper presents an iterative algorithm to find a
inverse kinematic solution of 5-DOF robot. The algorithm is to
minimize the iteration number. Since the 5-DOF robot cannot give full
orientation of tool. Only z-direction of tool is satisfied while rotation
of tool is determined by kinematic constraint. This work therefore
described how to specify the tool direction and let the tool rotation free.
The simulation results show that this algorithm effectively worked.
Using the proposed iteration algorithm, error due to inverse kinematics
converged to zero rapidly in 5 iterations. This algorithm was applied in
real welding robot and verified through various practical works.
Abstract: The design of an active leg orthosis for tumble
protection is proposed in this paper. The orthosis would be applied to
assist elders or invalids in rebalancing while they fall unexpectedly.
We observe the regain balance motion of healthy and youthful people,
and find the difference to elders or invalids. First, the physical model
of leg would be established, and we consider the leg motions are
achieve through four joints (phalanx stem, ankle, knee, and hip joint)
and five links (phalanges, talus, tibia, femur, and hip bone). To
formulate the dynamic equations, the coordinates which can clearly
describe the position in 3D space are first defined accordance with the
human movement of leg, and the kinematics and dynamics of the leg
movement can be formulated based on the robotics. For the purpose,
assisting elders and invalids in avoiding tumble, the posture variation
of unbalance and regaining balance motion are recorded by the
motion-capture image system, and the trajectory is taken as the desire
one. Then we calculate the force and moment of each joint based on
the leg motion model through programming MATLAB code. The
results would be primary information of the active leg orthosis design
for tumble protection.
Abstract: The purpose of this study is to find natural gait of
biped robot such as human being by analyzing the COG (Center Of
Gravity) trajectory of human being's gait. It is discovered that human
beings gait naturally maintain the stability and use the minimum
energy. This paper intends to find the natural gait pattern of biped
robot using the minimum energy as well as maintaining the stability by
analyzing the human's gait pattern that is measured from gait image on
the sagittal plane and COG trajectory on the frontal plane. It is not
possible to apply the torques of human's articulation to those of biped
robot's because they have different degrees of freedom. Nonetheless,
human and 5-link biped robots are similar in kinematics. For this, we
generate gait pattern of the 5-link biped robot by using the GA
algorithm of adaptation gait pattern which utilize the human's ZMP
(Zero Moment Point) and torque of all articulation that are measured
from human's gait pattern. The algorithm proposed creates biped
robot's fluent gait pattern as that of human being's and to minimize
energy consumption because the gait pattern of the 5-link biped robot
model is modeled after consideration about the torque of human's each
articulation on the sagittal plane and ZMP trajectory on the frontal
plane. This paper demonstrate that the algorithm proposed is superior
by evaluating 2 kinds of the 5-link biped robot applied to each gait
patterns generated both in the general way using inverse kinematics
and in the special way in which by considering visuality and
efficiency.
Abstract: Roundabout work on the principle of circulation and
entry flows, where the maximum entry flow rates depend largely on
circulating flow bearing in mind that entry flows must give away to
circulating flows. Where an existing roundabout has a road hump
installed at the entry arm, it can be hypothesized that the kinematics
of vehicles may prevent the entry arm from achieving optimum
performance. Road humps are traffic calming devices placed across
road width solely as speed reduction mechanism. They are the
preferred traffic calming option in Malaysia and often used on single
and dual carriageway local routes. The speed limit on local routes is
30mph (50 km/hr). Road humps in their various forms achieved the
biggest mean speed reduction (based on a mean speed before traffic
calming of 30mph) of up to 10mph or 16 km/hr according to the UK
Department of Transport. The underlying aim of reduced speed
should be to achieve a 'safe' distribution of speeds which reflects the
function of the road and the impacts on the local community.
Constraining safe distribution of speeds may lead to poor drivers
timing and delayed reflex reaction that can probably cause accident.
Previous studies on road hump impact have focused mainly on speed
reduction, traffic volume, noise and vibrations, discomfort and delay
from the use of road humps. The paper is aimed at optimal entry and
circulating flow induced by road humps. Results show that
roundabout entry and circulating flow perform better in
circumstances where there is no road hump at entrance.
Abstract: This paper features the kinematic modelling of a 5-axis stationary articulated robot arm which is used for doing successful robotic manipulation task in its workspace. To start with, a 5-axes articulated robot was designed entirely from scratch and from indigenous components and a brief kinematic modelling was performed and using this kinematic model, the pick and place task was performed successfully in the work space of the robot. A user friendly GUI was developed in C++ language which was used to perform the successful robotic manipulation task using the developed mathematical kinematic model. This developed kinematic model also incorporates the obstacle avoiding algorithms also during the pick and place operation.
Abstract: In this paper the direct kinematic model of a multiple
applications three degrees of freedom industrial manipulator, was
developed using the homogeneous transformation matrices and the
Denavit - Hartenberg parameters, likewise the inverse kinematic
model was developed using the same method, verifying that in the
workload border the inverse kinematic presents considerable errors,
therefore a genetic algorithm was implemented to optimize the model
improving greatly the efficiency of the model.
Abstract: Presents a concept for a multidisciplinary process
supporting effective task transitions between different technical
domains during the architectural design stage.
A system configuration challenge is the multifunctional driven
increased solution space. As a consequence, more iteration is needed
to find a global optimum, i.e. a compromise between involved
disciplines without negative impact on development time. Since state
of the art standards like ISO 15288 and VDI 2206 do not provide a
detailed methodology on multidisciplinary design process, higher
uncertainties regarding final specifications arise. This leads to the
need of more detailed and standardized concepts or processes which
could mitigate risks.
The performed work is based on analysis of multidisciplinary
interaction, of modeling and simulation techniques. To demonstrate
and prove the applicability of the presented concept, it is applied to
the design of aircraft high lift systems, in the context of the
engineering disciplines kinematics, actuation, monitoring, installation
and structure design.
Abstract: The paper deals with the kinematics and automated
calculation of intermittent mechanisms with radial cams. Currently,
electronic cams are increasingly applied in the drives of working link
mechanisms. Despite a huge advantage of electronic cams in their reprogrammability
or instantaneous change of displacement diagrams,
conventional cam mechanisms have an irreplaceable role in
production and handling machines. With high frequency of working
cycle periods, the dynamic load of the proper servomotor rotor
increases and efficiency of electronic cams strongly decreases.
Though conventional intermittent mechanisms with radial cams are
representatives of fixed automation, they have distinct advantages in
their high speed (high dynamics), positional accuracy and relatively
easy manufacture. We try to remove the disadvantage of firm
displacement diagram by reducing costs for simple design and
automated calculation that leads reliably to high-quality and
inexpensive manufacture.
Abstract: The aim of this study is to investigate the kinematics of undulatory elongated fish swimming against a velocity flow. We perform the experiments on European eel Anguilla Anguilla swimming in a hydrodynamic re-circulating tank with the velocity flow fixed at 0.2 m/s. We find that the undulating shape of overall eel body changes when it swims slantwise from the flow direction, by comparison to axial undulation shape. We examine this kinematics and we propose a general equation describing the lateral position of undulation body taking into account the direction of the eel-s swimming.
Abstract: In this paper, we have proposed a low cost optimized solution for the movement of a three-arm manipulator using Genetic Algorithm (GA) and Analytical Hierarchy Process (AHP). A scheme is given for optimizing the movement of robotic arm with the help of Genetic Algorithm so that the minimum energy consumption criteria can be achieved. As compared to Direct Kinematics, Inverse Kinematics evolved two solutions out of which the best-fit solution is selected with the help of Genetic Algorithm and is kept in search space for future use. The Inverse Kinematics, Fitness Value evaluation and Binary Encoding like tasks are simulated and tested. Although, three factors viz. Movement, Friction and Least Settling Time (or Min. Vibration) are used for finding the Fitness Function / Fitness Values, however some more factors can also be considered.
Abstract: Applicability of tuning the controller gains for Stewart manipulator using genetic algorithm as an efficient search technique is investigated. Kinematics and dynamics models were introduced in detail for simulation purpose. A PD task space control scheme was used. For demonstrating technique feasibility, a Stewart manipulator numerical-model was built. A genetic algorithm was then employed to search for optimal controller gains. The controller was tested onsite a generic circular mission. The simulation results show that the technique is highly convergent with superior performance operating for different payloads.
Abstract: The velocity of a moving point in a general path is the vector quantity, which has both magnitude and direction. The magnitude or the direction of the velocity vector can change over time as a result of acceleration that the time rate of velocity changes. Acceleration analysis is important because inertial forces and inertial torques are proportional to rectilinear and angular accelerations accordingly. The loads must be determined in advance to ensure that a machine is adequately designed to handle these dynamic loads. For planar motion, the vector direction of acceleration is commonly separated into two elements: tangential and centripetal or radial components of a point on a rotating body. All textbooks in physics, kinematics and dynamics of machinery consider the magnitude of a radial acceleration at condition when a point rotates with a constant angular velocity and it means without acceleration. The magnitude of the tangential acceleration considered on a basis of acceleration for a rotating point. Such condition of presentation of magnitudes for two components of acceleration logically and mathematically is not correct and may cause further confusion in calculation. This paper presents new analytical expressions of the radial and absolute accelerations of a rotating point with acceleration and covers the gap in theoretical study of acceleration analysis.
Abstract: This paper proposes a robot able to climb Columns.
This robot is not dependent on the diameter and material of the
columns. Some climbing robots have been designed up to now but
Koala robot was designed and fabricated for climbing columns
exclusively. Simple kinematics of climbing in the nature inspired us
to design this robot. We used two linear mechanisms to grip the
column. The gripper consists of a DC motor and a power screw
mechanism with a linear bushing as a guide. This mechanism
provides enough force to grip the column. In addition we needed an
actuator for climbing the column; hence, two pneumatic jacks were
used. All the mechanical parts were designed according to the
exerted forces and operational condition. The prototype can be
simply installed and controlled on the column by an inexperienced
operator. This robot is intended for inspection and surveillance of
pipes in oil industries and power poles in electric industries.
Abstract: As networking has become popular, Web-learning
tends to be a trend while designing a tool. Moreover, five-axis
machining has been widely used in industry recently; however, it has
potential axial table colliding problems. Thus this paper aims at
proposing an efficient web-learning collision detection tool on
five-axis machining. However, collision detection consumes heavy
resource that few devices can support, thus this research uses a
systematic approach based on web knowledge to detect collision. The
methodologies include the kinematics analyses for five-axis motions,
separating axis method for collision detection, and computer
simulation for verification. The machine structure is modeled as STL
format in CAD software. The input to the detection system is the
g-code part program, which describes the tool motions to produce the
part surface. This research produced a simulation program with C
programming language and demonstrated a five-axis machining
example with collision detection on web site. The system simulates the
five-axis CNC motion for tool trajectory and detects for any collisions
according to the input g-codes and also supports high-performance
web service benefiting from C. The result shows that our method
improves 4.5 time of computational efficiency, comparing to the
conventional detection method.