Abstract: Myoelectric control system is the fundamental
component of modern prostheses, which uses the myoelectric signals
from an individual’s muscles to control the prosthesis movements.
The surface electromyogram signal (sEMG) being noninvasive has
been used as an input to prostheses controllers for many years.
Recent technological advances has led to the development of
implantable myoelectric sensors which enable the internal
myoelectric signal (MES) to be used as input to these prostheses
controllers. The intramuscular measurement can provide focal
recordings from deep muscles of the forearm and independent signals
relatively free of crosstalk thus allowing for more independent
control sites. However, little work has been done to compare the two
inputs. In this paper we have compared the classification accuracy of
six pattern recognition based myoelectric controllers which use
surface myoelectric signals recorded using untargeted (symmetric)
surface electrode arrays to the same controllers with multichannel
intramuscular myolectric signals from targeted intramuscular
electrodes as inputs. There was no significant enhancement in the
classification accuracy as a result of using the intramuscular EMG
measurement technique when compared to the results acquired using
the surface EMG measurement technique. Impressive classification
accuracy (99%) could be achieved by optimally selecting only five
channels of surface EMG.
Abstract: This study investigates how the site specific traffic
data differs from the Mechanistic Empirical Pavement Design
Software default values. Two Weigh-in-Motion (WIM) stations were
installed in Interstate-40 (I-40) and Interstate-25 (I-25) to developed
site specific data. A computer program named WIM Data Analysis
Software (WIMDAS) was developed using Microsoft C-Sharp (.Net)
for quality checking and processing of raw WIM data. A complete
year data from November 2013 to October 2014 was analyzed using
the developed WIM Data Analysis Program. After that, the vehicle
class distribution, directional distribution, lane distribution, monthly
adjustment factor, hourly distribution, axle load spectra, average
number of axle per vehicle, axle spacing, lateral wander distribution,
and wheelbase distribution were calculated. Then a comparative
study was done between measured data and AASHTOWare default
values. It was found that the measured general traffic inputs for I-40
and I-25 significantly differ from the default values.
Abstract: This paper introduces an effective method of
segmenting Korean text (place names in Korean) from a Korean road
sign image. A Korean advanced directional road sign is composed of
several types of visual information such as arrows, place names in
Korean and English, and route numbers. Automatic classification of
the visual information and extraction of Korean place names from the
road sign images make it possible to avoid a lot of manual inputs to a
database system for management of road signs nationwide. We
propose a series of problem-specific heuristics that correctly segments
Korean place names, which is the most crucial information, from the
other information by leaving out non-text information effectively. The
experimental results with a dataset of 368 road sign images show 96%
of the detection rate per Korean place name and 84% per road sign
image.
Abstract: Revenue leakages are one of the major challenges
manufacturers face in production processes, as most of the input
materials that should emanate as products from the lines are lost as
waste. Rather than generating income from material input which is
meant to end-up as products, losses are further incurred as costs in
order to manage waste generated. In addition, due to the lack of a
clear view of the flow of resources on the lines from input to output
stage, acquiring information on the true cost of waste generated have
become a challenge. This has therefore given birth to the
conceptualization and implementation of waste minimization
strategies by several manufacturing industries. This paper reviews the
principles and applications of three environmental management
accounting tools namely Activity-based Costing (ABC), Life-Cycle
Assessment (LCA) and Material Flow Cost Accounting (MFCA) in
the manufacturing industry and their effectiveness in curbing revenue
leakages. The paper unveils the strengths and limitations of each of
the tools; beaming a searchlight on the tool that could allow for
optimal resource utilization, transparency in production process as
well as improved cost efficiency. Findings from this review reveal
that MFCA may offer superior advantages with regards to the
provision of more detailed information (both in physical and
monetary terms) on the flow of material inputs throughout the
production process compared to the other environmental accounting
tools. This paper therefore makes a case for the adoption of MFCA as
a viable technique for the identification and reduction of waste in
production processes, and also for effective decision making by
production managers, financial advisors and other relevant
stakeholders.
Abstract: Growing human population has placed increased
demands on water supplies and spurred a heightened interest in
desalination infrastructure. Key elements of the economics of
desalination projects are thermal and electrical inputs. With growing
concerns over use of fossil fuels to (indirectly) supply these inputs,
coupling of desalination with nuclear power production represents a
significant opportunity. Individually, nuclear and desalination
technologies have a long history and are relatively mature. For
desalination, Reverse Osmosis (RO) has the lowest energy inputs.
However, the economically driven output quality of the water
produced using RO, which uses only electrical inputs, is lower than the
output water quality from thermal desalination plants. Therefore,
modern desalination projects consider that RO should be coupled with
thermal desalination technologies (MSF, MED, or MED-TVC) with
attendant steam inputs to permit blending to produce various qualities
of water. A large nuclear facility is well positioned to dispatch large
quantities of both electrical and thermal power. This paper considers
the supply of thermal energy to a large desalination facility to examine
heat balance impact on the nuclear steam cycle. The APR1400 nuclear
plant is selected as prototypical from both a capacity and turbine cycle
heat balance perspective to examine steam supply and the impact on
electrical output. Extraction points and quantities of steam are
considered parametrically along with various types of thermal
desalination technologies to form the basis for further evaluations of
economically optimal approaches to the interface of nuclear power
production with desalination projects. In our study, the
thermodynamic evaluation will be executed by DE-TOP, an IAEA
sponsored program. DE-TOP has capabilities to analyze power
generation systems coupled to desalination plants through various
steam extraction positions, taking into consideration the isolation loop
between the nuclear and the thermal desalination facilities (i.e., for
radiological isolation).
Abstract: The importance of this study is to understand how Indonesian military court asserts its jurisdiction over military members who commit general crimes within the Indonesian military judiciary system in comparison to other countries. This research employs a normative-juridical approach in combination with historical and comparative-juridical approaches. The research specification is analytical-descriptive in nature, i.e. describing or outlining the principles, basic concepts, and norms related to military judiciary system, which are further analyzed within the context of implementation and as the inputs for military justice regulation under the Indonesian legal system. Main data used in this research are secondary data, including primary, secondary and tertiary legal sources. The research focuses on secondary data, while primary data are supplementary in nature. The validity of data is checked using multi-methods commonly known as triangulation, i.e. to reflect the efforts to gain an in-depth understanding of phenomena being studied. Here, the military element is kept intact in the judiciary process with due observance of the Military Criminal Justice System and the Military Command Development Principle. The Indonesian military judiciary jurisdiction over military members committing general crimes is based on national legal system and global development while taking into account the structure, composition and position of military forces within the state structure. Jurisdiction is formulated by setting forth the substantive norm of crimes that are military in nature. At the level of adjudication jurisdiction, the military court has a jurisdiction to adjudicate military personnel who commit general offences. At the level of execution jurisdiction, the military court has a jurisdiction to execute the sentence against military members who have been convicted with a final and binding judgement. Military court's jurisdiction needs to be expanded when the country is in the state of war.
Abstract: This paper presents the results of a Finite Element
based vibration analysis of a solar powered Unmanned Aerial
Vehicle (UAV). The purpose of this paper was to quantify the free
vibration, forced vibration response due to differing point inputs in
order to predict the relative response magnitudes and frequencies at
various wing locations of vibration induced power generators
(magnet in coil) excited by gust and/or control surface pulse-decays
used to help power the flight of the electric UAV. A Fluid Structure
Interaction (FSI) study was performed in order to ascertain pertinent
design stresses and deflections as well as aerodynamic parameters of
the UAV airfoil. The 10 ft span airfoil is modeled using Mylar as the
primary material. Results show that the free mode in bending is 4.8
Hz while the first forced bending mode is on range of 16.2 to 16.7 Hz
depending on the location of excitation. The free torsional bending
mode is 28.3 Hz, and the first forced torsional mode is range of 26.4
to 27.8 Hz, depending on the location of excitation. The FSI results
predict the coefficients of aerodynamic drag and lift of 0.0052 and
0.077, respectively, which matches hand-calculations used to validate
the Finite Element based results. FSI based maximum von Mises
stresses and deflections were found to be 0.282 MPa and 3.4 mm,
respectively. Dynamic pressures on the airfoil range from 1.04 to
1.23 kPa corresponding to velocity magnitudes in range of 22 to 66
m/s.
Abstract: The end of the line controls of the finished products in
the automotive industry is important. The control that has been
conducted with the manual methods for the sliding doors tracks is not
sufficient and faulty products cannot be identified. As a result, the
customer has the faulty products. In the scope of this study, the
design criteria of the PLC integrated modular end of line control unit
has been examined, designed and manufactured to make the control
of the 10 different track profile to 2 different vehicles with an
objective to minimize the salvage costs by obtaining more sensitive,
certain and accurate measurement results. In the study that started
with literature and patent review, the design inputs have been
specified, the technical concept has been developed, computer
supported mechanic design, control system and automation design,
design review and design improvement have been made. Laser
analog sensors at high sensitivity, probes and modular blocks have
been used in the unit. The measurement has been conducted in the
system and it is observed that measurement results are more sensitive
than the previous methods that we use.
Abstract: Life cycle assessment is a technique to assess the
environmental aspects and potential impacts associated with a
product, process, or service, by compiling an inventory of relevant
energy and material inputs and environmental releases; evaluating the
potential environmental impacts associated with identified inputs and
releases; and interpreting the results to help you make a more
informed decision. In this paper, the life cycle assessment of
aluminum and beech wood as two commonly used materials in Egypt
for window frames are heading, highlighting their benefits and
weaknesses. Window frames of the two materials have been assessed
on the basis of their production, energy consumption and
environmental impacts. It has been found that the climate change of
the windows made of aluminum and beech wood window, for a
reference window (1.2m×1.2m), are 81.7 mPt and -52.5 mPt impacts
respectively. Among the most important results are: fossil fuel
consumption, potential contributions to the green building effect and
quantities of solid waste tend to be minor for wood products
compared to aluminum products; incineration of wood products can
cause higher impacts of acidification and eutrophication than
aluminum, whereas thermal energy can be recovered.
Abstract: Voting algorithms are extensively used to make
decisions in fault tolerant systems where each redundant module
gives inconsistent outputs. Popular voting algorithms include
majority voting, weighted voting, and inexact majority voters. Each
of these techniques suffers from scenarios where agreements do not
exist for the given voter inputs. This has been successfully overcome
in literature using fuzzy theory. Our previous work concentrated on a
neuro-fuzzy algorithm where training using the neuro system
substantially improved the prediction result of the voting system.
Weight training of Neural Network is sub-optimal. This study
proposes to optimize the weights of the Neural Network using
Artificial Bee Colony algorithm. Experimental results show the
proposed system improves the decision making of the voting
algorithms.
Abstract: Market is an important factor for start-ups to look into
during decision-making in product development and related areas.
Emerging country markets are more uncertain in terms of information
availability and institutional supports. The literature review of market
uncertainty reveals the need for identifying factors representing the
market uncertainty. This paper identifies factors for market
uncertainty using Exploratory Factor Analysis (EFA) and confirmed
the number of factor retention using an alternative factor retention
criterion ‘Parallel Analysis’. 500 entrepreneurs, engaged in start-ups
from all over India participated in the study. This paper concludes
with the factor structure of ‘market uncertainty’ having dimensions of
uncertainty in industry orientation, uncertainty in customer
orientation and uncertainty in marketing orientation.
Abstract: Mobil Producing Nigeria Unlimited (MPNU), a
subsidiary of ExxonMobil and the highest crude oil & condensate
producer in Nigeria has its operational base and an oil terminal, the
Qua Iboe terminal (QIT) located at Ibeno, Nigeria. Other oil
companies like Network Exploration and Production Nigeria Ltd,
Frontier Oil Ltd; Shell Petroleum Development Company Ltd; Elf
Petroleum Nigeria Ltd and Nigerian Agip Energy, a subsidiary of the
Italian ENI E&P operate onshore, on the continental shelf and in deep
offshore of the Atlantic Ocean, respectively with the coastal waters of
Ibeno, Nigeria as the nearest shoreline. This study was designed to
delineate the oil-polluted sites in Ibeno, Nigeria using
microbiological and physico-chemical characterization of soils,
sediments and ground and surface water samples from the study area.
Results obtained revealed that there have been significant recent
hydrocarbon inputs into this environment as observed from the high
counts of hydrocarbonoclastic microorganisms in excess of 1% at all
the stations sampled. Moreover, high concentrations of THC, BTEX
and heavy metals contents in all the samples analyzed corroborate the
high recent crude oil input into the study area. The results also
showed that the pollution of the different environmental media
sampled were of varying degrees, following the trend: ground water
> surface water > sediments > soils.
Abstract: In the Hierarchical Temporal Memory (HTM) paradigm
the effect of overlap between inputs on the activation of columns in
the spatial pooler is studied. Numerical results suggest that similar
inputs are represented by similar sets of columns and dissimilar inputs
are represented by dissimilar sets of columns. It is shown that the
spatial pooler produces these results under certain conditions for
the connectivity and proximal thresholds. Following the discussion
of the initialization of parameters for the thresholds, corresponding
qualitative arguments about the learning dynamics of the spatial
pooler are discussed.
Abstract: Polymer Electrolyte Membrane Fuel Cell (PEMFC) is
such a time-vary nonlinear dynamic system. The traditional linear
modeling approach is hard to estimate structure correctly of PEMFC
system. From this reason, this paper presents a nonlinear modeling of
the PEMFC using Neural Network Auto-regressive model with
eXogenous inputs (NNARX) approach. The multilayer perception
(MLP) network is applied to evaluate the structure of the NNARX
model of PEMFC. The validity and accuracy of NNARX model are
tested by one step ahead relating output voltage to input current from
measured experimental of PEMFC. The results show that the obtained
nonlinear NNARX model can efficiently approximate the dynamic
mode of the PEMFC and model output and system measured output
consistently.
Abstract: In this contribution a structure for high level lateral vehicle tracking control based on the disturbance observer is presented. The structure is characterized by stationary compensating side forces disturbances and guaranteeing a cooperative behavior at the same time. Driver inputs are not compensated by the disturbance observer. Moreover the structure is especially useful as it robustly stabilizes the vehicle. Therefore the parameters are selected using the Parameter Space Approach. The implemented algorithms are tested in real world scenarios.
Abstract: Honeys are produced by Apis mellifera and stingless
bees (Meliponini) in Ecuador. We studied honey produced in
beeswax combs by Apis mellifera, and honey produced in pots by
Geotrigona and Scaptotrigona bees. Chloroform extracts of honey
were obtained for fast NMR spectra. The 1D spectra were acquired at
298 K, with a 600 MHz NMR Bruker instrument, using a modified
double pulsed field gradient spin echoes (DPFGSE) sequence.
Signals of 1H NMR spectra were integrated and used as inputs for
PCA, PLS-DA analysis, and labelled sets of classes were successfully
identified, enhancing the separation between the three groups of
honey according to the entomological origin: A. mellifera,
Geotrigona and Scaptotrigona. This procedure is therefore
recommended for authenticity test of honey in Ecuador.
Abstract: A model was constructed to predict the amount of
solar radiation that will make contact with the surface of the earth in
a given location an hour into the future. This project was supported
by the Southern Company to determine at what specific times during
a given day of the year solar panels could be relied upon to produce
energy in sufficient quantities. Due to their ability as universal
function approximators, an artificial neural network was used to
estimate the nonlinear pattern of solar radiation, which utilized
measurements of weather conditions collected at the Griffin, Georgia
weather station as inputs. A number of network configurations and
training strategies were utilized, though a multilayer perceptron with
a variety of hidden nodes trained with the resilient propagation
algorithm consistently yielded the most accurate predictions. In
addition, a modeled direct normal irradiance field and adjacent
weather station data were used to bolster prediction accuracy. In later
trials, the solar radiation field was preprocessed with a discrete
wavelet transform with the aim of removing noise from the
measurements. The current model provides predictions of solar
radiation with a mean square error of 0.0042, though ongoing efforts
are being made to further improve the model’s accuracy.
Abstract: Improved resource efficiency of production is a key
requirement for sustainable growth, worldwide. In this regards, by
considering the energy and tourism as the extra inputs to the classical
Coub-Douglas production function, this study aims at investigating
the efficiency changes in the North African countries. To this end, the
study uses panel data for the period 1995-2010 and adopts the
Malmquist index based on the data envelopment analysis. Results
show that tourism increases technical and scale efficiencies, while it
decreases technological and total factor productivity changes. On the
other hand, when the production function is augmented by the energy
input; technical efficiency change decreases, while the technological
change, scale efficiency change and total factor productivity change
increase. Thus, in order to satisfy the needs for sustainable growth,
North African governments should take some measures for increasing
the contribution that the tourism makes to economic growth and some
others for efficient use of resources in the energy sector.
Abstract: Nitrogen fertilizer is the most used and often the most
mismanaged nutrient input. Nitrogen management has tremendous
implications on crop productivity, quality and environmental
stewardship. Sufficient nitrogen is needed to optimum yield and
quality. Soil and in-season plant tissue testing for nitrogen status are
a time consuming and expensive process. Real time sensing of plant
nitrogen status can be a useful tool in managing nitrogen inputs. The
objectives of this project were to assess the reliability of remotely
sensed non-destructive plant nitrogen measurements compared to wet
chemistry data from sampled plant tissue, develop in-season nitrogen
recommendations based on remotely sensed data for improved
nitrogen use efficiency and assess the potential for determining yield
and quality from remotely sensed data. Very good correlations were
observed between early-season remotely sensed crop nitrogen status
and plant nitrogen concentrations and subsequent in-season fertilizer
recommendations. The transmittance/absorbance type meters gave
the most accurate readings. Early in-season fertilizer recommendation
would be to apply 40 kg nitrogen per hectare plus 15 kg nitrogen per
hectare for each unit difference measured with the SPAD meter
between the crop and reference area or 25 kg plus 13 kg per hectare
for each unit difference measured with the CCM 200. Once the crop
was sufficiently fertilized meter readings became inconclusive and
were of no benefit for determining nitrogen status, silage yield and
quality and grain yield and protein.
Abstract: The Blue Nile Basin is the most important tributary of
the Nile River. Egypt and Sudan are almost dependent on water
originated from the Blue Nile. This multi-dependency creates
conflicts among the three countries Egypt, Sudan, and Ethiopia
making the management of these conflicts as an international issue.
Good assessment of the water resources of the Blue Nile is an
important to help in managing such conflicts. Hydrological models
are good tool for such assessment. This paper presents a critical
review of the nature and variability of the climate and hydrology of
the Blue Nile Basin as a first step of using hydrological modeling to
assess the water resources of the Blue Nile. Many several attempts
are done to develop basin-scale hydrological modeling on the Blue
Nile. Lumped and semi distributed models used averages of
meteorological inputs and watershed characteristics in hydrological
simulation, to analyze runoff for flood control and water resource
management. Distributed models include the temporal and spatial
variability of catchment conditions and meteorological inputs to
allow better representation of the hydrological process. The main
challenge of all used models was to assess the water resources of the
basin is the shortage of the data needed for models calibration and
validation. It is recommended to use distributed model for their
higher accuracy to cope with the great variability and complexity of
the Blue Nile basin and to collect sufficient data to have more
sophisticated and accurate hydrological modeling.