Abstract: In this study, a computational fluid dynamics (CFD)
model has been developed for studying the effect of surface
roughness profile on the EHL problem. The cylinders contact
geometry, meshing and calculation of the conservation of mass and
momentum equations are carried out using the commercial software
packages ICEMCFD and ANSYS Fluent. The user defined functions
(UDFs) for density, viscosity and elastic deformation of the cylinders
as the functions of pressure and temperature are defined for the CFD
model. Three different surface roughness profiles are created and
incorporated into the CFD model. It is found that the developed CFD
model can predict the characteristics of fluid flow and heat transfer in
the EHL problem, including the main parameters such as pressure
distribution, minimal film thickness, viscosity, and density changes.
The results obtained show that the pressure profile at the center of the
contact area directly relates to the roughness amplitude. A rough
surface with kurtosis value of more than 3 has greater influence over
the fluctuated shape of pressure distribution than in other cases.
Abstract: It has experimentally been proved that the
performance of compression ignition (C.I.) engine is spray
characteristics related. In modern diesel engine the spray formation
and the eventual combustion process are the vital processes that offer
more challenges towards enhancing the engine performance. In the
present work the numerical simulation has been carried out for
evaporating diesel sprays using Fluent software. For computational
fluid dynamics simulation “Meshing” is done using Gambit software
before transmitting it into Fluent. The simulation is carried out using
hot bomb conditions under varying chamber conditions such as gas
pressure, nozzle diameter and fuel injection pressure. For comparison
purpose, the numerical simulations the chamber conditions were kept
the same as that of the experimental data. At varying chamber
conditions the spray penetration rates are compared with the existing
experimental results.
Abstract: This paper presents the findings from a numerical simulation of the flow in 37-rod fuel assembly models spaced by a double-wire trapezoidal wrapping as applied to the BREST-OD-300 experimental nuclear reactor. Data on a high static pressure distribution within the models, and equations for determining the fuel bundle flow friction factors have been obtained. Recommendations are provided on using the closing turbulence models available in the ANSYS Fluent. A comparative analysis has been performed against the existing empirical equations for determining the flow friction factors. The calculated and experimental data fit has been shown.
An analysis into the experimental data and results of the numerical simulation of the BREST-OD-300 fuel rod assembly hydrodynamic performance are presented.
Abstract: This numerical study aims to develop a coupled,
passive and active control strategy of the flow around a cylinder of
diameter D, and Re=4000. The strategy consists to put a cylindrical
rod in front of a deforming cylinder. The quasi- elliptical deformation
of cylinder follow a sinusoidal law in order to reduce the drag force.
To analyze the evolution of unsteady vortices, the Large Eddy
Simulation approach is used in this 2D simulation, carried out using
ANSYS – Fluent. The movement of deformation is reproduced using
an internal subroutine, introduced in the form of a User Defined
Function UDF. Two diameters of the rod were tested for a rod placed
at a distance L = 3 ×d, with an amplitudes of deformation A = 5%, A
= 25% and A = 50% of the cylinder diameter, the frequency of
deformation take the values fd = 1fn, 5fn and 8fn, which fn
represents the naturel vortex shedding frequency. The results show
substantial changes in the flow behavior and for a rod of 6mm (1%
D) with amplitude A = 25%, and with a 2fn frequency, drag
reduction of 60% was recorded.
Abstract: A multi-agent type robot for disaster response in calamity scene is proposed in this paper. The proposed grouped rescue robots can perform cooperative reconnaissance and surveillance to achieve a given rescue mission. The multi-agent rescue of dual set robot consists of one master set and three slave units. The research for this rescue robot system is going to detect at harmful environment where human is unreachable, such as the building is infected with virus or the factory has hazardous liquid in effluent. As a dual set robot, with Bluetooth and communication network, the master set can connect with slave units and send information back to computer by wireless and monitor. Therefore, rescuer can be informed the real-time information in a calamity area. Furthermore, each slave robot is able to obstacle avoidance by ultrasonic sensors, and encodes distance and location by compass. The master robot can integrate every devices information to increase the efficiency of prospected and research unknown area.
Abstract: This article deals with numerical simulation of the
floor heating convector in 3D. Numerical simulation is focused on
cooling mode of the floor heating convector. Geometrical model
represents section of the heat exchanger – two fins with the gap
between, pipes are not involved. Two types of fin are examined –
sinusoidal and angular shape with different fin spacing. Results of fin
spacing in case of constant Reynolds number are presented. For the
numerical simulation was used commercial software Ansys Fluent.
Abstract: Human heart valves diseased by congenital heart
defects, rheumatic fever, bacterial infection, cancer may cause stenosis
or insufficiency in the valves. Treatment may be with medication but
often involves valve repair or replacement (insertion of an artificial
heart valve). Bileaflet mechanical heart valves (BMHVs) are widely
implanted to replace the diseased heart valves, but still suffer from
complications such as hemolysis, platelet activation, tissue
overgrowth and device failure. These complications are closely related
to both flow characteristics through the valves and leaflet dynamics. In
this study, the physiological flow interacting with the moving leaflets
in a bileaflet mechanical heart valve (BMHV) is simulated with a
strongly coupled implicit fluid-structure interaction (FSI) method
which is newly organized based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (remeshing) of
FLUENT. The simulated results are in good agreement with previous
experimental studies. This study shows the applicability of the present
FSI model to the complicated physics interacting between fluid flow
and moving boundary.
Abstract: In the current work, a numerical parametric study was
performed in order to model the fluid mechanics in the riser of a
bubbling fluidized bed (BFB). The gas-solid flow was simulated by
mean of a multi-fluid Eulerian model incorporating the kinetic theory
for solid particles. The bubbling fluidized bed was simulated two
dimensionally by mean of a Computational Fluid Dynamic (CFD)
commercial software package, Fluent. The effects of using different
inter-phase drag function (the drag model of Gidaspow, Syamlal and
O-Brien and the EMMS drag model) on the model predictions were
evaluated and compared. The results showed that the drag models of
Gidaspow and Syamlal and O-Brien overestimated the drag force for
the FCC particles and predicted a greater bed expansion in
comparison to the EMMS drag model.
Abstract: This study investigated possible ways to improve the
efficiency of the platinum precipitation process using ammonium
chloride by reducing the platinum content reporting to the effluent.
The ore treated consist of five platinum group metals namely,
ruthenium, rhodium, iridium, platinum, palladium and a precious
metal gold. Gold, ruthenium, rhodium and iridium were extracted
prior the platinum precipitation process. Temperature, reducing
agent, flow rate and potential difference were the variables controlled
to determine the operation conditions for optimum platinum
precipitation efficiency. Hydrogen peroxide was added as the
oxidizing agent at the temperature of 85-90oC and potential
difference of 700-850mV was the variable used to check the
oxidizing state of platinum. The platinum was further purified at
temperature between 60-65oC, potential difference above 700 mV,
ammonium chloride of 200 l, and at these conditions the platinum
content reporting to the effluent was reduced to less than 300ppm,
resulting in optimum platinum precipitation efficiency and purity of
99.9%.
Abstract: A local wastewater treatment plant (WWTP)
experiencing poor nitrification tracked down high level of
surfactants in the plant-s influent and effluent. The aims of this project were to assess the potential inhibitory effect of surfactants on activated sludge processes. The effect of the
presence of TergitolNP-9, TrigetolNP-7, Trigetol15-S-9,
dodecylbenzene sulphonate (SDBS) and sodium dodecyl
sulfate (SDS) on activated sludge oxygen uptake rate (OUR) and nitrification were assessed. The average concentration of non-ionic and anionic
surfactants in the influent to the local WWTP were 7 and 8.7 mg/L, respectively. Removal of 67% to 90% of the non-ionic and 93-99% of the anionic surfactants tested were measured. All surfactants tested showed inhibitory effects both on OUR
and nitrification. SDS incurred the lowest inhibition whereas
SDBS and NP-9 caused severe inhibition to OUR and
Nitrification. Activated sludge flocs sizes slightly decreased
after 3 hours contact with the surfactant present in the test.
The results obtained indicated that high concentrations of
surfactants are likely to have an adverse effect on the
performance of WWTPs utilizing activated sludge processes.
Abstract: Laboratory experiments have been performed to investigate photocatalytic detoxification by using TiO2 photocatalyst for treating dairy effluent. Various operational parameters such as catalyst concentration, initial concentration, angle of tilt of solar flat plate reactor and flow rate were investigated. Results indicated that the photocatalytic detoxification process can efficiently treat dairy effluent. Experimental runs with dairy wastewater can be used to identify the optimum operational parameters to perform wastewater degradation on large scale for recycling purpose. Also effect of two different types of reactors on degradation process was analyzed.
Abstract: This article deals with the numerical simulation of the
floor heating convector in 3D. Presented convector can operate in
two modes – cooling mode and heating mode. This initial numerical
simulation is focused on cooling mode of the convector. Models with
different temperature of the fins are compared and three various
shapes of the fins are examined as well. The objective of the work is
to predict air flow and heat transfer inside convector for further
optimalization of these devices. For the numerical simulation was
used commercial software Ansys Fluent.
Abstract: Automatic detection of syllable repetition is one of the
important parameter in assessing the stuttered speech objectively.
The existing method which uses artificial neural network (ANN)
requires high levels of agreement as prerequisite before attempting to
train and test ANNs to separate fluent and nonfluent. We propose
automatic detection method for syllable repetition in read speech for
objective assessment of stuttered disfluencies which uses a novel
approach and has four stages comprising of segmentation, feature
extraction, score matching and decision logic. Feature extraction is
implemented using well know Mel frequency Cepstra coefficient
(MFCC). Score matching is done using Dynamic Time Warping
(DTW) between the syllables. The Decision logic is implemented by
Perceptron based on the score given by score matching. Although
many methods are available for segmentation, in this paper it is done
manually. Here the assessment by human judges on the read speech
of 10 adults who stutter are described using corresponding method
and the result was 83%.
Abstract: Anaerobic treatment has many advantages over other
biological method particularly when used to treat complex
wastewater such as petroleum refinery wastewater. In this study two
Up-flow Anaerobic Sludge Blanket (UASB) reactors were operated
in parallel to treat six volumetric organic loads (0.58, 1.21, 0.89,
2.34, 1.47 and 4.14 kg COD/m3·d) to evaluate the chemical oxygen
demand (COD) removal efficiency. The reactors were continuously
adapting to the changing of operation condition with increase in the
removal efficiency or slight decrease until the last load which was
more than two times the load, at which the reactor stressed and the
removal efficiency decreased to 75% with effluent concentration of
1746 mg COD/L. Other parameters were also monitored such as pH,
alkalinity, volatile fatty acid and gas production rate. The UASB
reactor was suitable to treat petroleum refinery wastewater and the
highest COD removal rate was 83% at 1215 kg/m3·d with COD
concentration about 356 mg/L in the effluent.
Abstract: There have been widespread applications of fluidized beds in industries which are related to the combination of gas-solid particles during the last decade. For instance, in order to crack the catalyses in petrochemical industries or as a drier in food industries. High capacity of fluidized bed in heat and mass transfer has made this device very popular. In order to achieve a higher efficiency of fluidized beds, a particular attention has been paid to beds with pulsating air flow. In this paper, a fluidized bed device with pulsating flow has been designed and constructed. Size of particles have been used during the test are in the range of 40 to 100μm. The purpose of this experimental test is to investigate the air flow regime, observe the particles- movement and measure the pressure loss along the bed. The effects of pulsation can be evaluated by comparing the results for both continuous and pulsating flow. Results of both situations are compared for various gas speeds. Moreover the above experiment is numerically simulated by using Fluent software and its numerical results are compared with the experimental results.
Abstract: From environmental aspect purification of ammonia
containing wastewater is expected. High efficiency ammonia
desorption can be done from the water by air on proper temperature.
After the desorption process, ammonia can be recovered and used in
another technology. The calculation method described below give
some methods to find either the minimum column height or ammonia
rich solution of the effluent.
Abstract: This research details a Computational Fluid Dynamics (CFD) approach to model fluid flow in a journal bearing with 8 equispaced semi-circular axial grooves. Water is used as the lubricant and is fed from one end of the bearing to the other, under pressure. The geometry of the bearing is modeled using a commercially available modeling software GAMBIT and the flow analysis is performed using a dedicated CFD analysis software FLUENT. The pressure distribution in the bearing clearance is obtained from FLUENT for various whirl ratios and is used to calculate the hydrodynamic force components in the radial and tangential direction of the bearing. These values along with the various whirl speeds can be used to do a regression analysis to determine the stiffness and damping coefficients. The values obtained are then compared with the stiffness and damping coefficients of a 3 Axial groove water lubricated journal bearing and those obtained from a FORTRAN code for a similar bearing.
Abstract: A method of dynamic mesh based airfoil optimization is proposed according to the drawbacks of surrogate model based airfoil optimization. Programs are designed to achieve the dynamic mesh. Boundary condition is add by integrating commercial software Pointwise, meanwhile the CFD calculation is carried out by commercial software Fluent. The data exchange and communication between the software and programs referred above have been accomplished, and the whole optimization process is performed in iSIGHT platform. A simplified airfoil optimization study case is brought out to show that aerodynamic performances of airfoil have been significantly improved, even save massive repeat operations and increase the robustness and credibility of the optimization result. The case above proclaims that dynamic mesh based airfoil optimization is an effective and high efficient method.