Abstract: Obfuscation is a low cost software protection
methodology to avoid reverse engineering and re engineering of
applications. Source code obfuscation aims in obscuring the source
code to hide the functionality of the codes. This paper proposes an
Array data transformation in order to obfuscate the source code
which uses arrays. The applications using the proposed data
structures force the programmer to obscure the logic manually. It
makes the developed obscured codes hard to reverse engineer and
also protects the functionality of the codes.
Abstract: Sedimentation is a hydraulic phenomenon that is
emerging as a serious challenge in river engineering. When the flow
reaches a certain state that gather potential energy, it shifts the
sediment load along channel bed. The transport of such materials can
be in the form of suspended and bed loads. The movement of these
along the river course and channels and the ways in which this could
influence the water intakes is considered as the major challenges for
sustainable O&M of hydraulic structures. This could be very serious
in arid and semi-arid regions like Iran, where inappropriate watershed
management could lead to shifting a great deal of sediments into the
reservoirs and irrigation systems. This paper aims to investigate
sedimentation in the Western Canal of Dez Diversion Weir in Iran,
identifying factors which influence the process and provide ways in
which to mitigate its detrimental effects by using the SHARC
Software.
For the purpose of this paper, data from the Dezful water authority
and Dezful Hydrometric Station pertinent to a river course of about 6
Km were used.
Results estimated sand and silt bed loads concentrations to be 193
ppm and 827ppm respectively. Given the available data on average
annual bed loads and average suspended sediment loads of 165ppm
and 837ppm, there was a significant statistical difference (16%)
between the sand grains, whereas no significant difference (1.2%)
was find in the silt grain sizes. One explanation for such finding
being that along the 6 Km river course there was considerable
meandering effects which explains recent shift in the hydraulic
behavior along the stream course under investigation. The sand
concentration in downstream relative to present state of the canal
showed a steep descending curve. Sediment trapping on the other
hand indicated a steep ascending curve. These occurred because the
diversion weir was not considered in the simulation model.
Abstract: This paper demonstrates an effort of a serviceoriented
engineering department in improving the sharing and
transfer of knowledge. Although the department consist of only six
employees, but it provides services in various chemical application in
an oil and gas business. The services provided span across Asia
Pacific region mainly Indonesia, Myanmar, Vietnam, Brunei,
Thailand and Singapore. Currently there are no effective tools or
integrated systems that support the sharing or transfer and
maintenance of knowledge so the department has considered
preserving this valuable knowledge by developing a Knowledge
Management System (KMS). This paper presents the development of
a KMS to support the sharing of knowledge in a service-oriented
engineering department of an oil and gas company. The embedded
features in the KMS like blog and forum will encourage iterative
process of knowledge sharing among the employees in the
department. The information and knowledge being shared, discussed
and communicated will be then achieved for future re-use. The re-use
of the knowledge allows the department to reduce redundant efforts
in providing consistent, up-to-date and cost effective of the best
solution to the its clients.
Abstract: The culture of riding heavy motorcycles originates
from advanced countries and mainly comes from Europe, North
America, and Japan. Heavy duty motorcycle riders are different from
people who view motorcycles as a convenient mean of transportation.
They regard riding them as a kind of enjoyment and high-level taste.
The activities of riding heavy duty motorcycles have formes a
distinctive landscape in domestic land in Taiwan. Previous studies
which explored motorcycle culture in Taiwan still focused on the
objects of motorcycle engine displacement under 50 cc.. The study
aims to study the heavy duty motorcycles of engine displacement over
550 cc. and explores where their attractiveness is. For finding the
attractiveness of heavy duty motorcycle, the study chooses Miryoku
Engineering (Preference-Based Design) approach. Two steps are
adopted to proceed the research. First, through arranging the letters
obtained from interviewing experts, EGM (The Evaluation Grid
Method) was applied to find out the structure of attractiveness. The
attractive styles are eye-dazzling, leisure, classic, and racing
competitive styles. Secondarily, Quantification Theory Type I analysis
was adopted as a tool for analyzing the importance of attractiveness.
The relationship between style and attractive parts was also discussed.
The results could contribute to the design and research development of
heavy duty motorcycle industry in Taiwan.
Abstract: Hybrid knowledge model is suggested as an underlying
framework for product development management. It can support such
hybrid features as ontologies and rules. Effective collaboration in
product development environment depends on sharing and reasoning
product information as well as engineering knowledge. Many studies
have considered product information and engineering knowledge.
However, most previous research has focused either on building the
ontology of product information or rule-based systems of engineering
knowledge. This paper shows that F-logic based knowledge model can
support such desirable features in a hybrid way.
Abstract: Emerging Bio-engineering fields such as Brain
Computer Interfaces, neuroprothesis devices and modeling and
simulation of neural networks have led to increased research activity
in algorithms for the detection, isolation and classification of Action
Potentials (AP) from noisy data trains. Current techniques in the field
of 'unsupervised no-prior knowledge' biosignal processing include
energy operators, wavelet detection and adaptive thresholding. These
tend to bias towards larger AP waveforms, AP may be missed due to
deviations in spike shape and frequency and correlated noise
spectrums can cause false detection. Also, such algorithms tend to
suffer from large computational expense.
A new signal detection technique based upon the ideas of phasespace
diagrams and trajectories is proposed based upon the use of a
delayed copy of the AP to highlight discontinuities relative to
background noise. This idea has been used to create algorithms that
are computationally inexpensive and address the above problems.
Distinct AP have been picked out and manually classified from
real physiological data recorded from a cockroach. To facilitate
testing of the new technique, an Auto Regressive Moving Average
(ARMA) noise model has been constructed bases upon background
noise of the recordings. Along with the AP classification means this
model enables generation of realistic neuronal data sets at arbitrary
signal to noise ratio (SNR).
Abstract: Students often adopt routine practicing as learning
strategy for mathematics. The reason is they are often bound and
trained to solving conventional-typed questions in Mathematics in
high school. This will be problematic if students further consolidate
this practice in university. Therefore, the Department of Mathematics
emphasized and integrated the Discovery-enriched approach in the
undergraduate curriculum. This paper presents the details of
implementing the Discovery-enriched Curriculum by providing
adequate platform for project-learning, expertise for guidance and
internship opportunities for students majoring in Mathematics. The
Department also provided project-learning opportunities to
mathematics courses targeted for students majoring in other science or
engineering disciplines. The outcome is promising: the research
ability and problem solving skills of students are enhanced.
Abstract: In this paper, an extended study is performed on the
effect of different factors on the quality of vector data based on a
previous study. In the noise factor, one kind of noise that appears in
document images namely Gaussian noise is studied while the previous
study involved only salt-and-pepper noise. High and low levels of
noise are studied. For the noise cleaning methods, algorithms that were
not covered in the previous study are used namely Median filters and
its variants. For the vectorization factor, one of the best available
commercial raster to vector software namely VPstudio is used to
convert raster images into vector format. The performance of line
detection will be judged based on objective performance evaluation
method. The output of the performance evaluation is then analyzed
statistically to highlight the factors that affect vector quality.
Abstract: The tray/multi-tray distillation process is a topic that
has been investigated to great detail over the last decade by many
teams such as Jubran et al. [1], Adhikari et al. [2], Mowla et al. [3],
Shatat et al. [4] and Fath [5] to name a few. A significant amount of
work and effort was spent focusing on modeling and/simulation of
specific distillation hardware designs. In this work, we have focused
our efforts on investigating and gathering experimental data on
several engineering and design variables to quantify their influence
on the yield of the multi-tray distillation process. Our goals are to
generate experimental performance data to bridge some existing gaps
in the design, engineering, optimization and theoretical modeling
aspects of the multi-tray distillation process.
Abstract: The Boundary Representation of a 3D manifold contains
FACES (connected subsets of a parametric surface S : R2 -!
R3). In many science and engineering applications it is cumbersome
and algebraically difficult to deal with the polynomial set and
constraints (LOOPs) representing the FACE. Because of this reason, a
Piecewise Linear (PL) approximation of the FACE is needed, which is
usually represented in terms of triangles (i.e. 2-simplices). Solving the
problem of FACE triangulation requires producing quality triangles
which are: (i) independent of the arguments of S, (ii) sensitive to the
local curvatures, and (iii) compliant with the boundaries of the FACE
and (iv) topologically compatible with the triangles of the neighboring
FACEs. In the existing literature there are no guarantees for the point
(iii). This article contributes to the topic of triangulations conforming
to the boundaries of the FACE by applying the concept of parameterindependent
Gabriel complex, which improves the correctness of the
triangulation regarding aspects (iii) and (iv). In addition, the article
applies the geometric concept of tangent ball to a surface at a point to
address points (i) and (ii). Additional research is needed in algorithms
that (i) take advantage of the concepts presented in the heuristic
algorithm proposed and (ii) can be proved correct.
Abstract: Graduate attributes have received increasing attention
over recent years as universities incorporate these attributes into the
curriculum. Graduates who have adequate technical knowledge only
are not sufficiently equipped to compete effectively in the work
place; they also need non disciplinary skills ie, graduate attributes.
The purpose of this paper is to investigate the impact of an eportfolio
in a technical communication course to enhance engineering
students- graduate attributes: namely, learning of communication,
critical thinking and problem solving and teamwork skills. Two
questionnaires were used to elicit information from the students: one
on their preferred and the other on the actual learning process. In
addition, student perceptions of the use of eportfolio as a learning
tool were investigated. Preliminary findings showed that most of the
students- expectations have been met with their actual learning. This
indicated that eportfolio has the potential as a tool to enhance
students- graduate attributes.
Abstract: To solve the quick and accurate level-adjusting
problem in the process of spacecraft precise mating, automatic leveling
and equalizing hoist device for spacecraft is developed. Based on
lifting point adjustment by utilizing XY-workbench, the leveling and
equalizing controller by a self-adaptive control algorithm is proposed.
By simulation analysis and lifting test using engineering prototype,
validity and reliability of the hoist device is verified, which can meet
the precision mating requirements of practical applications for
spacecraft.
Abstract: In order to upgrade the seismic resistibility of structures and enhance the functionality of an isolator, a new base isolator called the multiple trench friction pendulum system (MTFPS) is proposed in this study. The proposed MTFPS isolator is composed of a trench concave surface and several intermediate sliding plates in two orthogonal directions. Mathematical formulations have been derived to examine the characteristics of the proposed MTFPS isolator possessing multiple intermediate sliding plates. By means of mathematical formulations, it can be inferred that the natural period and damping effect of the MTFPS isolator with several intermediate sliding plates can be altered continually and controllably during earthquakes. Furthermore, results obtained from shaking table tests demonstrate that the proposed isolator provides good protection to structures for prevention of damage from strong earthquakes.
Abstract: Article presents the geometry and structure
reconstruction procedure of the aircraft model for flatter research
(based on the I22-IRYDA aircraft). For reconstruction the Reverse
Engineering techniques and advanced surface modeling CAD tools
are used. Authors discuss all stages of data acquisition process,
computation and analysis of measured data. For acquisition the three
dimensional structured light scanner was used. In the further sections,
details of reconstruction process are present. Geometry
reconstruction procedure transform measured input data (points
cloud) into the three dimensional parametric computer model
(NURBS solid model) which is compatible with CAD systems.
Parallel to the geometry of the aircraft, the internal structure
(structural model) are extracted and modeled. In last chapter the
evaluation of obtained models are discussed.
Abstract: Global Software Development (GSD) projects are
passing through different boundaries of a company, country and even
in other continents where time zone differs between both sites.
Beside many benefits of such development, research declared plenty
of negative impacts on these GSD projects. It is important to
understand problems which may lie during the execution of GSD
project with different time zones. This research project discussed and
provided different issues related to time delays in GSD projects. In
this paper, authors investigated some of the time delay factors which
usually lie in GSD projects with different time zones. This
investigation is done through systematic review of literature.
Furthermore, the practices to overcome these delay factors which
have already been reported in literature and GSD organizations are
also explored through literature survey and case studies.
Abstract: We have defined two suites of metrics, which cover
static and dynamic aspects of component assembly. The static
metrics measure complexity and criticality of component assembly,
wherein complexity is measured using Component Packing Density
and Component Interaction Density metrics. Further, four criticality
conditions namely, Link, Bridge, Inheritance and Size criticalities
have been identified and quantified. The complexity and criticality
metrics are combined to form a Triangular Metric, which can be used
to classify the type and nature of applications. Dynamic metrics are
collected during the runtime of a complete application. Dynamic
metrics are useful to identify super-component and to evaluate the
degree of utilisation of various components. In this paper both static
and dynamic metrics are evaluated using Weyuker-s set of properties.
The result shows that the metrics provide a valid means to measure
issues in component assembly. We relate our metrics suite with
McCall-s Quality Model and illustrate their impact on product
quality and to the management of component-based product
development.
Abstract: Collaborative working environments for distance
education can be considered as a more generic form of contemporary
remote labs. At present, the majority of existing real laboratories are
not constructed to allow the involved participants to collaborate in
real time. To make this revolutionary learning environment possible
we must allow the different users to carry out an experiment
simultaneously. In recent times, multi-user environments are
successfully applied in many applications such as air traffic control
systems, team-oriented military systems, chat-text tools, multi-player
games etc. Thus, understanding the ideas and techniques behind these
systems could be of great importance in the contribution of ideas to
our e-learning environment for collaborative working. In this
investigation, collaborative working environments from theoretical
and practical perspectives are considered in order to build an
effective collaborative real laboratory, which allows two students or
more to conduct remote experiments at the same time as a team. In
order to achieve this goal, we have implemented distributed system
architecture, enabling students to obtain an automated help by either
a human tutor or a rule-based e-tutor.
Abstract: The weight constrained shortest path problem
(WCSPP) is one of most several known basic problems in
combinatorial optimization. Because of its importance in many areas
of applications such as computer science, engineering and operations
research, many researchers have extensively studied the WCSPP.
This paper mainly concentrates on the reduction of total search space
for finding WCSP using some existing Genetic Algorithm (GA). For
this purpose, some controlled schemes of genetic operators are
adopted on list chromosome representation. This approach gives a
near optimum solution with smaller elapsed generation than classical
GA technique. From further analysis on the matter, a new
generalized schema theorem is also developed from the philosophy
of Holland-s theorem.
Abstract: In this work the numerical simulation of transient heat
transfer in a cylindrical probe is done. An experiment was conducted
introducing a steel cylinder in a heating chamber and registering its
surface temperature along the time during one hour. In parallel, a
mathematical model was solved for one dimension transient heat
transfer in cylindrical coordinates, considering the boundary
conditions of the test. The model was solved using finite difference
method, because the thermal conductivity in the cylindrical steel bar
and the convection heat transfer coefficient used in the model are
considered temperature dependant functions, and both conditions
prevent the use of the analytical solution. The comparison between
theoretical and experimental results showed the average deviation is
below 2%. It was concluded that numerical methods are useful in
order to solve engineering complex problems. For constant k and h,
the experimental methodology used here can be used as a tool for
teaching heat transfer in mechanical engineering, using mathematical
simplified models with analytical solutions.
Abstract: It is necessary to incorporate technological advances
achieved in the field of engineering into dentistry in order to enhance
the process of diagnosis, treatment planning and enable the doctors to
render better treatment to their patients. To achieve this ultimate goal
long distance collaborations are often necessary. This paper discusses
the various collaborative tools and their applications to solve a few
burning problems confronted by the dentists. Customization is often
the solution to most of the problems. But rapid designing,
development and cost effective manufacturing is a difficult task to
achieve. This problem can be solved using the technique of digital
manufacturing. Cases from 6 major branches of dentistry have been
discussed and possible solutions with the help of state of art
technology using rapid digital manufacturing have been proposed in
the present paper. The paper also entails the usage of existing tools in
collaborative and digital manufacturing area.