Abstract: A solar powered air heating system using parabolic trough collector was experimentally investigated. In this experimental setup, the reflected solar radiations were focused on absorber tube which was placed at focal length of the parabolic trough. In this setup, air was used as working fluid which collects the heat from absorber tube. To enhance the performance of parabolic trough, collector with different type of reflectors were used. It was observed For Aluminum sheet maximum temperature is 52.3ºC, which 24.22% more than steel sheet as reflector and 8.5% more than Aluminum foil as reflector, also efficiency by using Aluminum sheet as reflector compared to steel sheet as reflector is 61.18% more. Efficiency by using Aluminum sheet as reflector compared to Aluminum foil as reflector is 18.98% more.
Abstract: The evaluation of the convective heat transfer of flow in passages with rectangular cross section is still of interest for the heat transfer investigators, as in the air heater solar collectors. The aim of this paper is to present investigation results on the natural convection heat transfer in a solar air heater. The effect of the channel length as heat transfer surface and the inclination of the passage were investigated. The results were obtained experimentally and theoretically. For that, an experimental test rig was fabricated with channel lengths of 1m, 1.5m, and 2m. For each length, the air outlet and inlet temperatures, absorber and cover temperatures, solar radiation intensity and air flow rate were measured at 10o, 30o, 50o, 70o, and 90o tilt angles. Measurements were recorded every 2 hours interval to investigate the transient behavior of the system. The experimental and theoretical results are presented in terms of Nu number versus Ra number and discussed. The percentages of differences between experimental and theoretical results are within the margin of 6% to 13%, effectively. It is recommended to extend the investigation to study the same configurations with different artificial surface roughing by ribs or pins.
Abstract: Nano fibers produced by electrospinning are of industrial and scientific attention due to their special characteristics such as long length, small diameter and high surface area. Applications of electrospun structures in nanotechnology are included tissue scaffolds, fibers for drug delivery, composite reinforcement, chemical sensing, enzyme immobilization, membrane-based filtration, protective clothing, catalysis, solar cells, electronic devices and others. Many polymer and ceramic precursor nano fibers have been successfully electrospun with diameters in the range from 1 nm to several microns. The process is complex so that fiber diameter is influenced by various material, design and operating parameters. The objective of this work is to apply genetic algorithm on the parameters of electrospinning which have the most significant effect on the nano fiber diameter to determine the optimum parameter values before doing experimental set up. Effective factors including initial polymer concentration, initial jet radius, electrical potential, relaxation time, initial elongation, viscosity and distance between nozzle and collector are considered to determine finest diameter which is selected by user.
Abstract: Hybrid photovoltaic thermal (PV/T) solar system comprises a solar collector which is disposed on photovoltaic solar cells. The disadvantage of a conventional photovoltaic cell is that its performance decreases as the temperature increases. Indeed, part of the solar radiation is converted into electricity and is dissipated as heat, increasing the temperature of the photovoltaic cell with respect to the ambient temperature. The objective of this work is to study experimentally and implement a hybrid prototype to evaluate electrical and thermal performance. In this paper, an experimental study of two new configurations of hybrid collectors is exposed. The results are given and interpreted. The two configurations of absorber studied are a new combination with tubes and galvanized tank, the other is a tubes and sheet.
Abstract: A solar powered air heating system using one ended evacuated tubes is experimentally investigated. A solar air heater containing forty evacuated tubes is used for heating purpose. The collector surface area is about 4.44 m2. The length and outer diameters of the outer glass tube and absorber tube are 1500, 47 and 37 mm, respectively. In this experimental setup, we have a header (heat exchanger) of square shape (190 mm x 190 mm). The length of header is 1500 mm. The header consists of a hollow pipe in the center whose diameter is 60 mm through which the air is made to flow. The experimental setup contains approximately 108 liters of water. Water is working as heat collecting medium which collects the solar heat falling on the tubes. This heat is delivered to the air flowing through the header pipe. This heat flow is due to natural convection and conduction. The outlet air temperature depends upon several factors along with air flow rate and solar radiation intensity. The study has been done for both up-flow and down-flow of air in header in similar weather conditions, at different flow rates. In the present investigations the study has been made to find the effect of intensity of solar radiations and flow rate of air on the out let temperature of the air with time and which flow is more efficient. The obtained results show that the system is highly effective for the heating in this region. Moreover, it has been observed that system is highly efficient for the particular flow rate of air. It was also observed that downflow configuration is more effective than up-flow condition at all flow rates due to lesser losses in down-flow. The results show that temperature differences of upper head and lower head, both of water and surface of pipes on the respective ends is lower in down-flow.
Abstract: Numerical analysis of flow characteristics and
separation efficiency in a high-efficiency cyclone has been performed.
Several models based on the experimental observation for a design
purpose were proposed. However, the model is only estimated the
cyclone's performance under the limited environments; it is difficult to
obtain a general model for all types of cyclones. The purpose of this
study is to find out the flow characteristics and separation efficiency
numerically. The Reynolds stress model (RSM) was employed instead
of a standard k-ε or a k-ω model which was suitable for isotropic
turbulence and it could predict the pressure drop and the Rankine
vortex very well. For small particles, there were three significant
components (entrance of vortex finder, cone, and dust collector) for
the particle separation. In the present work, the particle re-entraining
phenomenon from the dust collector to the cyclone body was observed
after considerable time. This re-entrainment degraded the separation
efficiency and was one of the significant factors for the separation
efficiency of the cyclone.
Abstract: A lightpipe is an about 99 percent specular reflective
mirror pipe or duct that is used for the transmission of the daylight
from the outside into a building. The lightpipes are usually used in
the daylighting buildings, in the residential, industrial and
commercial sectors. This paper is about the performances of a
lightpipe installed in a laboratory (3 m x 2.6 m x 3 m) without
windows. The aim is to analyse the luminous intensity distribution
for several sky/sun conditions. The lightpipe was monitored during
the year 2006. The lightpipe is 1 m long and the diameter of the top
collector and of the internal diffuser device is 0.25 m. In the
laboratory there are seven illuminance sensors: one external is
located on the roof of the laboratory and six internal sensors are
connected to a data acquisition system. The internal sensors are
positioned under the internal diffusive device at an height of 0.85 m
from the floor to simulate a working plane. The numerical data are
obtained through a simulation software. This paper shows the
comparison between the experimental and numerical results
concerning the behavior of the lightpipe.
Abstract: This study investigated the effect of oxygen and
micro-cracking on the flotation of low grade nickel sulphide ore. The
ore treated contained serpentine minerals which have a history of
being difficult to process efficiently. The use of oxygen as a bubbling
gas has been noted to be effective because it increases the pulp
potential. The desired effect of micro cracking the ore is that the
nickel sulphide minerals will become activated and this activation
will render these minerals more susceptible to react with potassium
amyl xanthate collectors, resulting in a higher recovery of nickel and
hinder the recovery of other undesired minerals contained in the ore.
Higher nickel recoveries were obtained when pure oxygen was used
as a bubbling gas rather than the conventional air. Microwave
cracking favored the recovery of nickel.
Abstract: National Biodiversity Database System (NBIDS) has
been developed for collecting Thai biodiversity data. The goal of this
project is to provide advanced tools for querying, analyzing,
modeling, and visualizing patterns of species distribution for
researchers and scientists. NBIDS data record two types of datasets:
biodiversity data and environmental data. Biodiversity data are
specie presence data and species status. The attributes of biodiversity
data can be further classified into two groups: universal and projectspecific
attributes. Universal attributes are attributes that are common
to all of the records, e.g. X/Y coordinates, year, and collector name.
Project-specific attributes are attributes that are unique to one or a
few projects, e.g., flowering stage. Environmental data include
atmospheric data, hydrology data, soil data, and land cover data
collecting by using GLOBE protocols. We have developed webbased
tools for data entry. Google Earth KML and ArcGIS were used
as tools for map visualization. webMathematica was used for simple
data visualization and also for advanced data analysis and
visualization, e.g., spatial interpolation, and statistical analysis.
NBIDS will be used by park rangers at Khao Nan National Park, and
researchers.
Abstract: The accelerated growth in aircraft industries desire
effectual schemes, programs, innovative designs of advanced systems
and facilities to accomplish the augmenting need for home-free air
transportation. In this paper, a contemporary conceptual design of a
cambered airfoil has been proposed in order to providing augmented
effective lift force relative to the airplane, and to eliminating
drawbacks and limitations of an airfoil in a commercial airplane by
using a kind of smart materials. This invention of an unsymmetrical
airfoil structure utilizes the amplified air momentum around the
airfoil and increased camber length to providing improved aircraft
performance and assist to enhancing the reliability of the aircraft
components. Moreover, this conjectured design helps to reducing
airplane weight and total drag.
Abstract: Energy and exergy study of air-water combined solar collector which is called dual purpose solar collector (DPSC) is investigated. The method of ε - NTU is used. Analysis is performed for triangle channels. Parameters like the air flow rate and water inlet temperature are studied. Results are shown that DPSC has better energy and exergy efficiency than single collector. In addition, the triangle passage with water inlet temperature of 60O C has shown better exergy and energy efficiency.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: It is well known that surface enhancements play an important role in augmenting the thermal performance of flat plate solar collector. In this paper, an attempt is made to explain in a comparative way the effect of surface geometry of solar collector having dimple geometry with that of a flat plate solar collector of the same size. A CFD analysis was carried out for the two cases, subjected to a constant heat flux of 600W/m2 and 1000W/m2. It can be inferred from the study that the absorber plate temperature shows a rise of average surface temperature of about 50C for the dimple solar collector when compared to a flat plate solar collector. Most importantly, the average exit water temperature shows a marked improvement of about 5.50C for a dimple solar collector as compared to that of a flat plate solar collector.
Abstract: The objective of this paper was to designing a
ventilation system to enhance the performance of roof solar collector
(RSC) for reducing heat accumulation inside the house. The RSC has
1.8 m2 surface area made of CPAC monier roof tiles on the upper part
and gypsum board on the lower part. The space between CPAC
monier and gypsum board was fixed at 14 cm.
Ventilation system of modified roof solar collector (modified
RSC) consists of 9 tubes of 0.15m diameter and installed in the
lower part of RSC. Experimental result showed that the temperature
of the room, and attic temperature. The average temperature
reduction of room of house used modified RSC is about 2oC. and the
percentage of room temperature reduction varied between 0 to 10%.
Therefore, modified RSC is an interesting option in the sense that it
promotes solar energy and conserve energy.
Abstract: Virtually all existing networked system management
tools use a Manager/Agent paradigm. That is, distributed agents are
deployed on managed devices to collect local information and report
it back to some management unit. Even those that use standard
protocols such as SNMP fall into this model. Using standard protocol
has the advantage of interoperability among devices from different
vendors. However, it may not be able to provide customized
information that is of interest to satisfy specific management needs.
In this dissertation work, different approaches are used to
collect information regarding the devices attached to a Local Area
Network. An SNMP aware application is being developed that will
manage the discovery procedure and will be used as data collector.
Abstract: The objectif of the present work is to determinate the
potential of the solar parabolic trough collector (PTC) for use in the
design of a solar thermal power plant in Algeria. The study is based
on a mathematical modeling of the PTC. Heat balance has been
established respectively on the heat transfer fluid (HTF), the absorber
tube and the glass envelop using the principle of energy conservation
at each surface of the HCE cross-sectionn. The modified Euler
method is used to solve the obtained differential equations. At first
the results for typical days of two seasons the thermal behavior of the
HTF, the absorber and the envelope are obtained. Then to determine
the thermal performances of the heat transfer fluid, different oils are
considered and their temperature and heat gain evolutions compared.
Abstract: A solar refrigeration system based on the adsorptiondesorption
phenomena is designed and analyzed. An annular tubular
generator filled with silica gel adsorbent and with a perforated inner
cylinder is integrated within a flat solar collector. The working fluid
in the refrigeration cycle is water. The thermodynamic analysis and
because of the temperature level that could be attained with a flat
solar collector it is required that the system operates under vacuum
conditions. In order to enhance the performance of the system and to
get uniform temperature in the silica gel and higher desorbed mass,
an apparatus for rotation of the generator is incorporated in the
system. Testing is carried out and measurements are taken on the
designed installation. The effect of rotation is checked on the
temperature distribution and on the performance of this machine and
compared to the flat solar collector with fixed generator.
Abstract: Solar energy is the most “available", ecological and clean energy. This energy can be used in active or passive mode. The active mode implies the transformation of solar energy into a useful energy. The solar energy can be transformed into thermal energy, using solar collectors. In these collectors, the active and the most important element is the absorber, material which performs the absorption of solar radiation and, in at the same time, limits its reflection. The paper presents some aspects regarding the IR absorbing material – a type of cermets, used as absorber in the solar collectors, by X Ray Diffraction Technique (XRD) characterization.
Abstract: This paper presents the exergy analysis of a
desalination unit using humidification-dehumidification process.
Here, this unit is considered as a thermal system with three main
components, which are the heating unit by using a solar collector, the
evaporator or the humidifier, and the condenser or the dehumidifier.
In these components the exergy is a measure of the quality or grade
of energy and it can be destroyed in them. According to the second
law of thermodynamics this destroyed part is due to irreversibilities
which must be determined to obtain the exergetic efficiency of the
system.
In the current paper a computer program has been developed using
visual basic to determine the exergy destruction and the exergetic
efficiencies of the components of the desalination unit at variable
operation conditions such as feed water temperature, outlet air
temperature, air to feed water mass ratio and salinity, in addition to
cooling water mass flow rate and inlet temperature, as well as
quantity of solar irradiance.
The results obtained indicate that the exergy efficiency of the
humidifier increases by increasing the mass ratio and decreasing the
outlet air temperature. In the other hand the exergy efficiency of the
condenser increases with the increase of this ratio and also with the
increase of the outlet air temperature.
Abstract: A simple mobile engine-driven pneumatic paddy
collector made of locally available materials using local
manufacturing technology was designed, fabricated, and tested for
collecting and bagging of paddy dried on concrete pavement. The
pneumatic paddy collector had the following major components:
radial flat bladed type centrifugal fan, power transmission system,
bagging area, frame and the conveyance system. Results showed
significant differences on the collecting capacity, noise level, and fuel
consumption when rotational speed of the air mover shaft was varied.
Other parameters such as collecting efficiency, air velocity,
augmented cracked grain percentage, and germination rate were not
significantly affected by varying rotational speed of the air mover
shaft. The pneumatic paddy collector had a collecting efficiency of
99.33 % with a collecting capacity of 2685.00 kg/h at maximum
rotational speed of centrifugal fan shaft of about 4200 rpm. The
machine entailed an investment cost of P 62,829.25. The break-even
weight of paddy was 510,606.75 kg/yr at a collecting cost of 0.11
P/kg of paddy. Utilizing the machine for 400 hours per year
generated an income of P 23,887.73. The projected time needed to
recover cost of the machine based on 2685 kg/h collecting capacity
was 2.63 year.