Abstract: A solar receiver is designed for operation under
extremely uneven heat flux distribution, cyclic weather, and cloud
transient cycle conditions, which can include large thermal stress and
even receiver failure. In this study, the effect of different oil velocity
on convection coefficient factor and impact of wind velocity on local
Nusselt number by Finite Volume Method will be analyzed. This
study is organized to give an overview of the numerical modeling
using a MATLAB software, as an accurate, time efficient and
economical way of analyzing the heat transfer trends over stationary
receiver tube for different Reynolds number. The results reveal when
oil velocity is below 0.33m/s, the value of convection coefficient is
negligible at low temperature. The numerical graphs indicate that
when oil velocity increases up to 1.2 m/s, heat convection coefficient
increases significantly. In fact, a reduction in oil velocity causes a
reduction in heat conduction through the glass envelope. In addition,
the different local Nusselt number is reduced when the wind blows
toward the concave side of the collector and it has a significant effect
on heat losses reduction through the glass envelope.
Abstract: Fresh water is one of the resources which is getting
depleted day by day. A wise method to address this issue is by the
application of renewable energy-sun irradiation and by means of
decentralized, cheap, energetically self-sufficient, robust and simple
to operate plants, distillates can be obtained from sea, river or even
sewage. Solar desalination is a technique used to desalinate water
using solar energy. The present work deals with the comprehensive
design and simulation of solar tracking system using LabVIEW,
temperature and mass flow rate control of the solar desalination plant
using LabVIEW and also analysis of single phase inverter circuit
with LC filters for solar pumping system in MATLAB. The main
objective of this work is to improve the performance of solar
desalination system using automatic tracking system, output control
using temperature and mass flow rate control system and also to
reduce the harmonic distortion in the solar pumping system by means
of LC filters. The simulation of single phase inverter was carried out
using MATLAB and the output waveforms were analyzed.
Simulations were performed for optimum output temperature control,
which in turn controls the mass flow rate of water in the thermal
collectors. Solar tracking system was accomplished using LABVIEW
and was tested successfully. The thermal collectors are tracked in
accordance with the sun’s irradiance levels, thereby increasing the
efficiency of the thermal collectors.
Abstract: In most existing buildings in hot climate, cooling
loads lead to high primary energy consumption and consequently
high CO2 emissions. These can be substantially decreased with
integrated renewable energy systems. Kuwait is characterized by its
dry hot long summer and short warm winter. Kuwait receives annual
total radiation more than 5280 MJ/m2 with approximately 3347 h of
sunshine. Solar energy systems consist of PV modules and parabolic
trough collectors are considered to satisfy electricity consumption,
domestic water heating, and cooling loads of an existing building.
This paper presents the results of an extensive program of energy
conservation and energy generation using integrated photovoltaic
(PV) modules and Parabolic Trough Collectors (PTC). The program
conducted on an existing institutional building intending to convert it
into a Net-Zero Energy Building (NZEB) or near net Zero Energy
Building (nNZEB). The program consists of two phases; the first
phase is concerned with energy auditing and energy conservation
measures at minimum cost and the second phase considers the
installation of photovoltaic modules and parabolic trough collectors.
The 2-storey building under consideration is the Applied Sciences
Department at the College of Technological Studies, Kuwait. Single
effect lithium bromide water absorption chillers are implemented to
provide air conditioning load to the building. A numerical model is
developed to evaluate the performance of parabolic trough collectors
in Kuwait climate. Transient simulation program (TRNSYS) is
adapted to simulate the performance of different solar system
components. In addition, a numerical model is developed to assess
the environmental impacts of building integrated renewable energy
systems. Results indicate that efficient energy conservation can play
an important role in converting the existing buildings into NZEBs as
it saves a significant portion of annual energy consumption of the
building. The first phase results in an energy conservation of about
28% of the building consumption. In the second phase, the integrated
PV completely covers the lighting and equipment loads of the
building. On the other hand, parabolic trough collectors of optimum
area of 765 m2 can satisfy a significant portion of the cooling load,
i.e about73% of the total building cooling load. The annual avoided
CO2 emission is evaluated at the optimum conditions to assess the
environmental impacts of renewable energy systems. The total annual
avoided CO2 emission is about 680 metric ton/year which confirms
the environmental impacts of these systems in Kuwait.
Abstract: This paper presents the influences on the entrainment
of serpentines by grinding and reagents during copper–nickel sulfide
flotation. The previous bench flotation tests were performed to extract
the metallic values from the ore in Yunnan Mine, China and the
relatively satisfied results with recoveries of 86.92% Cu, 54.92% Ni,
and 74.73% Pt+Pd in the concentrate were harvested at their grades of
4.02%, 3.24% and 76.61 g/t, respectively. However, the content of
MgO in the concentrate was still more than 19%. Micro-flotation tests
were conducted with the objective of figuring out the influences on the
entrainment of serpentines into the concentrate by particle size,
flocculants or depressants and collectors, as well as visual
observations in suspension by OLYMPUS camera. All the tests results
pointed to the presences of both “entrapped-in” serpentines and its
coating on the hydrophobic flocs resulted from strong collectors
(combination of butyl xanthate, butyl ammonium dithophosphate,
even after adding carboxymethyl cellulose as effective depressant.
And fine grinding may escalate the entrainment of serpentines in the
concentrate.
Abstract: A solar dish collector has been designed, fabricated
and tested for its performance on 10-03-2015 in Salem, Tamilnadu,
India. The experiments on cooking vessels of coated and un-coated
with 5 Liters capacity have been used for cooking Rice. The results
are shown in graphs. The solar cooker is always capable of cooking
food within the expected length of time and based on the solar
radiation levels. With minimum cooking power, the coated pressure
cooker of 5 Liters capacity cooks the food at faster manner. This is
due to the conductivity of the coating material provided in the cooker.
Abstract: The thermal performance of a solar water heating with
1.00 m2 flat plate collectors in Cascavel - PR, is which presented in
this article, paper presents the solution to leverage the marketing of
solar heating systems through detailed constituent materials of the
solar collector studies, these abundant materials in construction, such
as expanded polyethylene, PVC, aluminum and glass tubes, mixing
them with new materials to minimize loss of efficiency while
decreasing its cost. The system was tested during months and the
collector obtained maximum recorded temperature of outlet fluid of
55°C, while the maximum temperature of the water at the bottom of
the hot water tank was 35°C. The average daily energy collected was
19.6 MJ/d; the energy supplied by the solar plate was 16.2 MJ/d; the
loss in the feed pipe was 3.2 MJ/d; the solar fraction was 32.2%, the
efficiency of the collector was 45.6% and the efficiency of the system
was 37.8%.
Abstract: Parabolic solar trough systems have seen limited
deployments in cold northern climates as they are more suitable for
electricity production in southern latitudes. A numerical dynamic
model is developed to simulate troughs installed in cold climates and
validated using a parabolic solar trough facility in Winnipeg. The
model is developed in Simulink and will be utilized to simulate a trigeneration
system for heating, cooling and electricity generation in
remote northern communities. The main objective of this simulation
is to obtain operational data of solar troughs in cold climates and use
the model to determine ways to improve the economics and address
cold weather issues.
In this paper the validated Simulink model is applied to simulate a
solar assisted absorption cooling system along with electricity
generation using Organic Rankine Cycle (ORC) and thermal storage.
A control strategy is employed to distribute the heated oil from solar
collectors among the above three systems considering the
temperature requirements. This modelling provides dynamic
performance results using measured meteorological data recorded
every minute at the solar facility location. The purpose of this
modeling approach is to accurately predict system performance at
each time step considering the solar radiation fluctuations due to
passing clouds. Optimization of the controller in cold temperatures is
another goal of the simulation to for example minimize heat losses in
winter when energy demand is high and solar resources are low.
The solar absorption cooling is modeled to use the generated heat
from the solar trough system and provide cooling in summer for a
greenhouse which is located next to the solar field.
The results of the simulation are presented for a summer day in
Winnipeg which includes comparison of performance parameters of
the absorption cooling and ORC systems at different heat transfer
fluid (HTF) temperatures.
Abstract: Solar energy is a good option among renewable
energy resources due to its easy availability and abundance. The
simplest and most efficient way to utilize solar energy is to convert it
into thermal energy and this can be done with the help of solar
collectors. The thermal performance of such collectors is poor due to
less heat transfer from the collector surface to air. In this work,
experimental investigations of single pass solar air heater having
triangular duct and provided with roughness element on the underside
of the absorber plate. V-shaped ribs are used for investigation having
three different values of relative roughness pitch (p/e) ranges from 4-
16 for a fixed value of angle of attack (α), relative roughness height
(e/Dh) and a relative gap distance (d/x) values are 60°, 0.044 and 0.60
respectively. Result shows that considerable augmentation in heat
transfer has been obtained by providing roughness.
Abstract: For cycling, the analysis of the pedal force is one of the
important factors in the study of exercise ability assessment and
overuse injuries. In past studies, a two-axis measurement sensor was
used at the sagittal plane to measure the force only in the anterior,
posterior, and vertical directions and to analyze the loss of force and
the injury on the frontal plane due to the forces in the right and left
directions. In this study, which is a basic study on diverse analyses of
the pedal force that consider the forces on the sagittal plane and the
frontal plane, a three-axis pedal force measurement sensor was
developed to measure the anterior-posterior (Fx), medio-lateral (Fz),
and vertical (Fy) forces. The sensor was fabricated with a size and
shape similar to those of the general flat pedal, and had a 550g weight
that allowed smooth pedaling. Its measurement range was ±1000 N for
Fx and Fz and ±2000 N for Fy, and its non-linearity, hysteresis, and
repeatability were approximately 0.5%. The data were sampled at
1000 Hz using a signal collector. To use the developed sensor, the
pedaling efficiency (index of efficiency, IE) and the range of left and
right (medio-lateral, ML) forces were measured with two seat heights
(low and high). The results of the measurement showed that the IE was
higher and the force range in the ML direction was lower with the high
position than with the low position. The developed measurement
sensor and its application results will be useful in understanding and
explaining the complicated pedaling technique, and will enable
diverse kinematic analyses of the pedal force on the sagittal plane and
the frontal plane.
Abstract: Solar air heater is a type of heat exchanger which
transforms solar radiation into heat energy. The thermal performance
of conventional solar air heater has been found to be poor because of
the low convective heat transfer coefficient from the absorber plate to
the air. It is attributed to the formation of a very thin boundary layer
at the absorber plate surface commonly known as viscous sub-layer.
Thermal efficiency of solar air heater can be improved by providing
the artificial roughness on absorber plate is the most efficient
technique. In this paper an attempt is made to provide artificial
roughness by incorporating inclined multiple V-ribs in the underside
of the absorber plate. 60˚V – ribs are arranged inclined to the
direction of air flow. Performance of collector estimated theoretically
and experimentally. Results of the investigation reveal that thermal
efficiency of collector with multiple V-ribs increased by 14%.
Abstract: A single-phase closed thermosyphon has been
fabricated and experimented to utilize solar energy for water heating.
The working fluid of the closed thermosyphon is heated at the flatplate
collector and the hot water goes to the water tank due to density
gradient caused by temperature differences. This experimental work
was done using insulated water tank and insulated connecting pipe
between the tank and the flat-plate collector. From the collected data,
performance parameters such as instantaneous collector efficiency
and heat removal factor are calculated. In this study, the effects of
glazing were also observed. The water temperature rise and the
maximum instantaneous efficiency obtained from this experiment
with glazing using insulated water tank and insulated connecting pipe
are 17°C in a period of 5 hours and 60% respectively. Whereas the
water temperature rise and the maximum instantaneous efficiency
obtained from this experiment with glazing using non-insulated water
tank and non-insulated connecting pipe are 14°C in a period of 5
hours and 39% respectively.
Abstract: In order to efficiently solve the problems created by the deepening energy crisis affecting Europe and the world,
governments cannot neglect the opportunities of using the energy
produced by sun collectors. In many of the EU countries there are sun
collectors producing heat energy, e.g. in 2011 in the area of EU27
(countries which belong to European Union) + Switzerland altogether
37519126 m2 were operated, which are capable of producing 26.3
GWh heat energy. The energy produced by these sun collectors is
utilized at the place of production. In the near future governments
will have to focus more on spreading and using sun collectors.
Among the complex problems of operating sun collectors, this article
deals with determining the optimal tilt angle, directions of sun
collectors. We evaluate the contamination of glass surface of sun
collector to the produced energy. Our theoretically results are confirmed by laboratory measurements. The purpose of our work is to help users and engineers in determination of optimal operation
parameters of sun collectors.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: Effects of insertion of coiled wire in juxtaposition with twisted tapes on heat transfer rate and solar radiation without disturbing the flow inside the riser tubes in a solar flat plate collector is experimentally reconnoitered in this present work. The wire coil used as a turbulator is placed inside the riser tube while the twisted tape is inserted into the wire coil to create a continuous swirling flow along the tube wall. The results of the heat transfer have been compared well with the available results. The heat transfer rate in the collector has been found to be increased by 18% to 70%. Solar water heaters having inserts in the flow tubes perform better than the conventional plain ones. It has been observed that heat losses are reduced consequently increasing the thermal performance about 30% over the plain water heaters under the same operating conditions. The effect of twisted tape with wire coils, flow Reynolds number, and the intensity of solar radiation on the thermal performance of the solar water heater has been presented. Effects of insertion of coiled wire in juxtaposition with twisted tapes on heat transfer rate and solar radiation without disturbing the flow inside the riser tubes in a solar flat plate collector is experimentally reconnoitered in this present work. The wire coil used as a turbulator is placed inside the riser tube while the twisted tape is inserted into the wire coil to create a continuous swirling flow along the tube wall. The results of the heat transfer have been compared well with the available results. The heat transfer rate in the collector has been found to be increased by 18% to 70%. Solar water heaters having inserts in the flow tubes perform better than the conventional plain ones. It has been observed that heat losses are reduced consequently increasing the thermal performance about 30% over the plain water heaters under the same operating conditions. The effect of twisted tape with wire coils, flow Reynolds number, and the intensity of solar radiation on the thermal performance of the solar water heater has been presented.
Abstract: Vibration analysis of most critical equipment is considered as one of the most challenging activities in preventive maintenance. Utilities are heart of the process in big industrial plants like petrochemical zones. Vibration analysis methods and condition monitoring systems of these kinds of equipments are developed too much in recent years. On the other hand, there are too much operation factors like inlet and outlet pressures and temperatures that should be monitored. In this paper, some of the most effective concepts and techniques related to gas turbine vibration analysis are discussed. In addition, a gas turbine SIEMENS 162MW - V94.2 vibration case history related to Iran power industry in Fars province is explained. Vibration monitoring system and machinery technical specification are introduced. Besides, absolute and relative vibration trends, turbine and compressor orbits, Fast Fourier transform (FFT) in absolute vibrations, vibration modal analysis, turbine and compressor start up and shut down conditions, bode diagrams for relative vibrations, Nyquist diagrams and waterfall or three-dimensional FFT diagrams in startup and trip conditions are discussed with relative graphs. Furthermore, Split Resonance in gas turbines is discussed in details. Moreover, some updated vibration monitoring system, blade manufacturing technique and modern damping mechanism are discussed in this paper.
Abstract: Owing to the lack of synchronization between the solar energy availability and the heat demands in a specific application, the energy storing sub-system is necessary to maintain the continuity of thermal process. The present work is dealing with an active solar heating storing system in which an air solar collector is connected to storing unit where this energy is distributed and provided to the heated space in a controlled manner. The solar collector is a box type absorber where the air flows between a number of vanes attached between the collector absorber and the bottom plate. This design can improve the efficiency due to increasing the heat transfer area exposed to the flowing air, as well as the heat conduction through the metal vanes from the top absorbing surface. The storing unit is a packed bed type where the air is coming from the air collector and circulated through the bed in order to add/remove the energy through the charging / discharging processes, respectively. The major advantage of the packed bed storage is its high degree of thermal stratification. Numerical solution of the packed bed energy storage is considered through dividing the bed into a number of equal segments for the bed particles and solved the energy equation for each segment depending on the neighbor ones. The studied design and performance parameters in the developed simulation model including, particle size, void fraction, etc. The final results showed that the collector efficiency was fluctuated between 55%-61% in winter season (January) under the climatic conditions of Misurata in Libya. Maximum temperature of 52ºC is attained at the top of the bed while the lower one is 25ºC at the end of the charging process of hot air into the bed. This distribution can satisfy the required load for the most house heating in Libya.
Abstract: Hybrid photovoltaic thermal (PVT) collectors allow simultaneous production of electrical energy thus heat energy. There are several configurations of hybrid collectors (to produce water or air). For hybrids water collectors, there are several configurations that differ by the nature of the absorber (serpentine, tubes...). In this paper, an absorber tank is studied. The circulation of the coolant is natural (we do not use the pump). We present the obtained results in our experimental study and we analyzed the data, and then we compare the results with the theory practices. The electrical performances of the hybrid collector are compared with those of conventional photovoltaic module mounted on the same structure and measured under the same conditions.
We conducted experiments with natural circulation of the coolant (Thermosyphon), for a flow rate of 0.025kg/m².
Abstract: Energy is required in almost every aspect of human activities and development of any nation in the world. Increasing fossil fuel price, energy security and climate change have important bearings on sustainable development of any nation. The renewable energy technology is considered one of the drastic approaches which taken over the world to reduce the energy problem. The preservation of vegetables by freezing is one of the most important methods of retaining quality in agricultural products over long-term storage periods. Freezing factories show high demand of energy for both heat and electricity; the hybrid Photovoltaic/Thermal (PV/T) systems could be used in order to meet this requirement. This paper presents PV/T system design for freezing factory. Also, the complete mathematical modeling and MATLAB SIMULINK of PV/T collector is introduced. The sensitivity analysis for the manufacturing parameters of PV/T collector is carried out to study their effect on both thermal and electrical efficiency.
Abstract: In this study, photocatalytic degradation of phenol by
titanium dioxide (TiO2) in aqueous solution was evaluated. The UV
energy of solar light was utilized by compound parabolic collectors
(CPCs) technology. The effect of irradiation time, initial pH, and
dosage of TiO2 were investigated. Aromatic intermediates (catechol,
benzoquinone, and hydroquinone) were quantified during the reaction
to study the pathways of the oxidation process. 94.5% degradation
efficiency of phenol was achieved after 150 minutes of irradiation
when the initial concentration was 100 mg/L. The dosage of TiO2
significantly affected the degradation efficiency of phenol. The
observed optimum pH for the reaction was 5.2. Phenol photocatalytic
degradation fitted to the pseudo-first order kinetic according to
Langmuir–Hinshelwood model.
Abstract: One of the most challenging times in operation of big industrial plant or utilities is the time that alert lamp of Bently Nevada connection in main board substation turn on and show the alert condition of machine. All of the maintenance groups usually make a lot of discussion with operation and together rather this alert signal is real or fake. This will be more challenging when condition monitoring vibrationdata shows 1X(X=current rotor frequency) in fast Fourier transform(FFT) and vibration phase trends show 90 degree shift between two non-contact probedirections with overall high radial amplitude amounts. In such situations, CM (condition monitoring) groups usually suspicious about unbalance in rotor. In this paper, four critical case histories related to SIEMENS V94.2 Gas Turbines in Iran power industry discussed in details. Furthermore, probe looseness and fake (unreal) trip in gas turbine power plants discussed. In addition, critical operation decision in alert condition in power plants discussed in details.