Abstract: We present a label-free biosensor based on
electrochemical impedance spectroscopy for the detection of proinflammatory
cytokine Tumor Necrosis Factor (TNF-α). Secretion of
TNF-α has been correlated to the onset of various diseases including
rheumatoid arthritis, Crohn-s disease etc. Gold electrodes were
patterned on a silicon substrate and self assembled monolayer of
dithiobis-succinimidyl propionate was used to develop the biosensor
which achieved a detection limit of ~57fM. A linear relationship was
also observed between increasing TNF-α concentrations and chargetransfer
resistance within a dynamic range of 1pg/ml – 1ng/ml.
Abstract: An on-line condition monitoring method for transmission line is proposed using electrical circuit theory and IT technology in this paper. It is reasonable that the circuit parameters such as resistance (R), inductance (L), conductance (g) and capacitance (C) of a transmission line expose the electrical conditions and physical state of the line. Those parameters can be calculated from the linear equation composed of voltages and currents measured by synchro-phasor measurement technique at both end of the line. A set of linear voltage drop equations containing four terminal constants (A, B ,C ,D ) are mathematical models of the transmission line circuits. At least two sets of those linear equations are established from different operation condition of the line, they may mathematically yield those circuit parameters of the line. The conditions of line connectivity including state of connecting parts or contacting parts of the switching device may be monitored by resistance variations during operation. The insulation conditions of the line can be monitored by conductance (g) and capacitance(C) measurements. Together with other condition monitoring devices such as partial discharge, sensors and visual sensing device etc.,they may give useful information to monitor out any incipient symptoms of faults. The prototype of hardware system has been developed and tested through laboratory level simulated transmission lines. The test has shown enough evident to put the proposed method to practical uses.
Abstract: Nowadays, one of the most important problems of the
metropolises and the world large cities is the habitant traffic difficulty
and lack of sufficient parking site for the vehicles. Esfahan city as the
third metropolis of Iran has encountered with the vehicles parkingplace
problems in the most parts of fourteen regions of the city. The
non principled and non systematic dispersal and lack of parking sites
in the city has created an unfavorable status for its traffic and has
caused the air and sound pollutions increase; in addition, it wastes the
most portions of the citizenship and travelers' charge and time in
urban pathways and disturbs their mental and psychical calmness,
thus leads to their intensive dissatisfaction. In this study, by the usage
of AHP model in GIS environment, the effective criteria in selecting
the public parking sites have been combined with each other, and the
results of the created layers overlapping represent the parking
utilitarian vastness and widths. The achieved results of this research
indicate the pretty appropriate public parking sites selection in region
number 3 of Esfahan; but inconsequential dispersal and lack of these
parking sites in this region have caused abundant transportation
problems in Esfahan city.
Abstract: A design flow of multi-standard down-conversion
CMOS mixers for three modern standards: Global System Mobile,
Digital Enhanced Cordless Telephone and Universal Mobile
Telecommunication Systems is presented. Three active mixer-s
structures are studied. The first is based on the Gilbert cell which
gives a tolerable noise figure and linearity with a low conversion
gain. The second and third structures use the current bleeding and
charge injection techniques in order to increase the conversion gain.
An improvement of about 2 dB of the conversion gain is achieved
without a considerable degradation of the other characteristics. The
models used for noise figure, conversion gain and IIP3 used are
studied. This study describes the nature of trade-offs inherent in such
structures and gives insights that help in identifying which structure
is better for given conditions.
Abstract: Bionanotechnology deals with nanoscopic interactions between nanostructured materials and biological systems. Polymer nanocomposites with optimized biological activity have attracted great attention. Nanoclay is considered as reinforcing nanofiller in manufacturing of high performance nanocomposites. In current study, organomodified-nanoclay with negatively charged silicate layers was incorporated into biomedical grade silicone rubber. Nanoparticle loading has been tailored to enhance cell behavior. Addition of nanoparticles led to improved mechanical properties of substrate with enhanced strength and stiffness while no toxic effects was observed. Results indicated improved viability and proliferation of cells by addition of nanofillers. The improved mechanical properties of the matrix result in proper cell response through adjustment and arrangement of cytoskeletal fibers. Results can be applied in tissue engineering when enhanced substrates are required for improvement of cell behavior for in vivo applications.
Abstract: Dust acoustic solitary waves are studied in warm
dusty plasma containing negatively charged dusts, nonthermal ions
and Boltzmann distributed electrons. Sagdeev pseudopotential
method is used in order to investigate solitary wave solutions in the
plasmas. The existence of compressive and rarefractive solitons is
studied.
Abstract: Uranium mining and processing in Brazil occur in a
northeastern area near to Caetité-BA. Several Non-Governmental
Organizations claim that uranium mining in this region is a pollutant
causing health risks to the local population,but those in charge of the
complex extraction and production of“yellow cake" for generating
fuel to the nuclear power plants reject these allegations. This study
aimed at identifying potential problems caused by mining to the
population of Caetité. In this, work,the concentrations of 238U, 232Th
and 40K radioisotopes in the teeth of the Caetité population were
determined by ICP-MS. Teeth are used as bioindicators of
incorporated radionuclides. Cumulative radiation doses in the
skeleton were also determined. The concentration values were below
0.008 ppm, and annual effective dose due to radioisotopes are below
to the reference values. Therefore, it is not possible to state that the
mining process in Caetité increases pollution or radiation exposure in
a meaningful way.
Abstract: Direct conversion of methane to methanol by partial oxidation in a thermal reactor has a poor yield of about 2% which is less than the expected economical yield of about 10%. Conventional thermal catalytic reactors have been proposed to be superseded by plasma reactors as a promising approach, due to strength of the electrical energy which can break C-H bonds of methane. Among the plasma techniques, non-thermal dielectric barrier discharge (DBD) plasma chemical process is one of the most future promising technologies in synthesizing methanol. The purpose of this paper is presenting a brief review of CH4 oxidation with O2 in DBD plasma reactors based on the recent investigations. For this reason, the effect of various parameters of reactor configuration, feed ratio, applied voltage, residence time (gas flow rate), type of applied catalyst, pressure and reactor wall temperature on methane conversion and methanol selectivity are discussed.
Abstract: In this paper, a one-dimensional numerical approach is
used to study the effect of applying electrohydrodynamics on the
temperature and species mass fraction profiles along the microcombustor.
Premixed mixture is H2-Air with a multi-step chemistry
(9 species and 19 reactions). In the micro-scale combustion because
of the increasing ratio of area-to-volume, thermal and radical
quenching mechanisms are important. Also, there is a significant heat
loss from the combustor walls. By inserting a number of electrodes
into micro-combustor and applying high voltage to them corona
discharge occurs. This leads in moving of induced ions toward
natural molecules and colliding with them. So this phenomenon
causes the movement of the molecules and reattaches the flow to the
walls. It increases the velocity near the walls that reduces the wall
boundary layer. Consequently, applying electrohydrodynamics
mechanism can enhance the temperature profile in the microcombustor.
Ultimately, it prevents the flame quenching in microcombustor.
Abstract: In this paper, the full state feedback controllers
capable of regulating and tracking the speed trajectory are presented.
A fourth order nonlinear mean value model of a 448 kW turbocharged
diesel engine published earlier is used for the purpose.
For designing controllers, the nonlinear model is linearized and
represented in state-space form. Full state feedback controllers
capable of meeting varying speed demands of drivers are presented.
Main focus here is to investigate sensitivity of the controller to the
perturbations in the parameters of the original nonlinear model.
Suggested controller is shown to be highly insensitive to the
parameter variations. This indicates that the controller is likely
perform with same accuracy even after significant wear and tear of
engine due to its use for years.
Abstract: Hexavalent chromium is highly toxic to most living organisms and a known human carcinogen by the inhalation route of exposure. Therefore, treatment of Cr(VI) contaminated wastewater is essential before their discharge to the natural water bodies. Cr(VI) reduction to Cr(III) can be beneficial because a more mobile and more toxic chromium species is converted to a less mobile and less toxic form. Zero-valence-state metals, such as scrap iron, can serve as electron donors for reducing Cr(VI) to Cr(III). The influence of pH on scrap iron capacity to reduce Cr(VI) was investigated in this study. Maximum reduction capacity of scrap iron was observed at the beginning of the column experiments; the lower the pH, the greater the experiment duration with maximum scrap iron reduction capacity. The experimental results showed that highest maximum reduction capacity of scrap iron was 12.5 mg Cr(VI)/g scrap iron, at pH 2.0, and decreased with increasing pH up to 1.9 mg Cr(VI)/g scrap iron at pH = 7.3.
Abstract: The performance and the plasma created by a pulsed
magnetoplasmadynamic thruster for small satellite application is
studied to understand better the ablation and plasma propagation
processes occurring during the short-time discharge. The results can
be applied to improve the quality of the thruster in terms of efficiency,
and to tune the propulsion system to the needs required by the satellite
mission. Therefore, plasma measurements with a high-speed camera
and induction probes, and performance measurements of mass bit
and impulse bit were conducted. Values for current sheet propagation
speed, mean exhaust velocity and thrust efficiency were derived from
these experimental data. A maximum in current sheet propagation
was found by the high-speed camera measurements for a medium
energy input and confirmed by the induction probes. A quasilinear
tendency between the mass bit and the energy input, the current
action integral respectively, was found, as well as a linear tendency
between the created impulse and the discharge energy. The highest
mean exhaust velocity and thrust efficiency was found for the highest
energy input.
Abstract: Petroleum refineries discharged large amount of
wastewater -during the refining process- that contains hazardous
constituents that is hard to degrade. Anaerobic treatment process is
well known as an efficient method to degrade high strength
wastewaters. Up-flow Anaerobic Sludge Blanker (UASB) is a
common process used for various wastewater treatments. Two UASB
reactors were set up and operated in parallel to evaluate the treatment
efficiency of petroleum refinery wastewater. In this study four
organic volumetric loading rates were applied (i.e. 0.58, 0.89, 1.21
and 2.34 kg/m3·d), two loads to each reactor. Each load was applied
for a period of 60 days for the reactor to acclimatize and reach steady
state, and then the second load applied. The chemical oxygen demand
(COD) removals were satisfactory with the removal efficiencies at the
loadings applied were 78, 82, 83 and 81 % respectively.
Abstract: Wireless Sensor Networks (WSNs) are wireless
networks consisting of number of tiny, low cost and low power
sensor nodes to monitor various physical phenomena like
temperature, pressure, vibration, landslide detection, presence of any
object, etc. The major limitation in these networks is the use of nonrechargeable
battery having limited power supply. The main cause of
energy consumption WSN is communication subsystem. This paper
presents an efficient grid formation/clustering strategy known as Grid
based level Clustering and Aggregation of Data (GCAD). The
proposed clustering strategy is simple and scalable that uses low duty
cycle approach to keep non-CH nodes into sleep mode thus reducing
energy consumption. Simulation results demonstrate that our
proposed GCAD protocol performs better in various performance
metrics.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: Concerning the inpatient care the present situation is
characterized by intense charges of medical technology into the
clinical daily routine and an ever stronger integration of special
techniques into the clinical workflow. Medical technology is by now
an integral part of health care according to consisting general
accepted standards. Purchase and operation thereby represent an
important economic position and both are subject of everyday
optimisation attempts. For this purpose by now exists a huge number
of tools which conduce more likely to a complexness of the problem
by a comprehensive implementation. In this paper the advantages of
an integrative information-workflow on the life-cycle-management in
the region of medical technology are shown.
Abstract: Decentralized eco-sanitation system is a promising and sustainable mode comparing to the century-old centralized conventional sanitation system. The decentralized concept relies on an environmentally and economically sound management of water, nutrient and energy fluxes. Source-separation systems for urban waste management collect different solid waste and wastewater streams separately to facilitate the recovery of valuable resources from wastewater (energy, nutrients). A resource recovery centre constituted for 20,000 people will act as the functional unit for the treatment of urban waste of a high-density population community, like Singapore. The decentralized system includes urine treatment, faeces and food waste co-digestion, and horticultural waste and organic fraction of municipal solid waste treatment in composting plants. A design model is developed to estimate the input and output in terms of materials and energy. The inputs of urine (yellow water, YW) and faeces (brown water, BW) are calculated by considering the daily mean production of urine and faeces by humans and the water consumption of no-mix vacuum toilet (0.2 and 1 L flushing water for urine and faeces, respectively). The food waste (FW) production is estimated to be 150 g wet weight/person/day. The YW is collected and discharged by gravity into tank. It was found that two days are required for urine hydrolysis and struvite precipitation. The maximum nitrogen (N) and phosphorus (P) recovery are 150-266 kg/day and 20-70 kg/day, respectively. In contrast, BW and FW are mixed for co-digestion in a thermophilic acidification tank and later a decentralized/centralized methanogenic reactor is used for biogas production. It is determined that 6.16-15.67 m3/h methane is produced which is equivalent to 0.07-0.19 kWh/ca/day. The digestion residues are treated with horticultural waste and organic fraction of municipal waste in co-composting plants.
Abstract: The use of artificial neural network (ANN) modeling
for prediction and forecasting variables in water resources
engineering are being increasing rapidly. Infrastructural applications
of ANN in terms of selection of inputs, architecture of networks,
training algorithms, and selection of training parameters in different
types of neural networks used in water resources engineering have
been reported. ANN modeling conducted for water resources
engineering variables (river sediment and discharge) published in
high impact journals since 2002 to 2011 have been examined and
presented in this review. ANN is a vigorous technique to develop
immense relationship between the input and output variables, and
able to extract complex behavior between the water resources
variables such as river sediment and discharge. It can produce robust
prediction results for many of the water resources engineering
problems by appropriate learning from a set of examples. It is
important to have a good understanding of the input and output
variables from a statistical analysis of the data before network
modeling, which can facilitate to design an efficient network. An
appropriate training based ANN model is able to adopt the physical
understanding between the variables and may generate more effective
results than conventional prediction techniques.
Abstract: Droughts are complex, natural hazards that, to a
varying degree, affect some parts of the world every year. The range
of drought impacts is related to drought occurring in different stages
of the hydrological cycle and usually different types of droughts,
such as meteorological, agricultural, hydrological, and socioeconomical
are distinguished. Streamflow drought was analyzed by
the method of truncation level (at 70% level) on daily discharges
measured in 54 hydrometric stations in southwestern Iran. Frequency
analysis was carried out for annual maximum series (AMS) of
drought deficit volume and duration series. Some factors including
physiographic, climatic, geologic, and vegetation cover were studied
as influential factors in the regional analysis. According to the results
of factor analysis, six most effective factors were identified as area,
rainfall from December to February, the percent of area with
Normalized Difference Vegetation Index (NDVI)
Abstract: Today, cancer remains one of the major diseases that
lead to death. The main obstacle in chemotherapy as a main cancer
treatment is the toxicity to normal cells due to Multidrug Resistance
(MDR) after the use of anticancer drugs. Proposed solution to
overcome this problem is the use of MDR efflux inhibitor of cinchona
alkaloids which is delivered together with anticancer drugs
encapsulated in the form of polymeric nanoparticles. The particles
were prepared by the hydration method. The characterization of
nanoparticles was particle size, zeta potential, entrapment efficiency
and in vitro drug release. Combination nanoparticle size ranged 29-45
nm with a neutral surface charge. Entrapment efficiency was above
87% for the use quinine, quinidine or cinchonidine in combination
with etoposide. The release test results exhibited that the cinchona
alkaloids release released faster than that of etoposide. Collectively,
cinchona alkaloids can be packaged along with etoposide in
nanomicelles for better cancer therapy.