Abstract: The effect of Alumina nanoparticle size on thermophysical
properties, heat transfer performance and pressure loss characteristics of
Aviation Turbine Fuel (ATF)-Al2O3 nanofluids is studied experimentally for
the proposed application of regenerative cooling of semi-cryogenic rocket
engine thrust chambers. Al2O3 particles with mean diameters of 50 nm or 150
nm are dispersed in ATF. At 500C and 0.3% particle volume concentration,
the bigger particles show increases of 17% in thermal conductivity and 55% in
viscosity, whereas the smaller particles show corresponding increases of 21%
and 22% for thermal conductivity and viscosity respectively. Contrary to these
results, experiments to study the heat transfer performance and pressure loss
characteristics show that at the same pumping power, the maximum
enhancement in heat transfer coefficient at 500C and 0.3% concentration is
approximately 47% using bigger particles, whereas it is only 36% using
smaller particles.
Abstract: This research were investigated, determined, and
analyzed of the climate characteristically change in the provincial
Udon Thani in the period of 60 surrounding years from 1951 to 2010
A.D. that it-s transferred to effects of climatologically data for
determining global warming. Statistically significant were not found
for the 60 years- data (R2
Abstract: The main issue in sweetening natural gas is H2S
dissociation. The present study is concerned with simulating thermal
dissociation of H2S in industrial natural gas carbon black furnace.
The comparison of calculated results against experimental
measurements shows good agreement. The results show that sulfur
derived from H2S thermal dissociation peaked at φ=0.95. H2S
thermal dissociation is enhanced in equivalence ratio upper than 1
and H2S oxidization is increased in equivalence ratio lower than 1.
H2 concentration of H2S thermal dissociation is increased with
increase of equivalence ratio up to 1. Also, H2S concentration
decreased in outlet as equivalence ratio increases. H2S thermal
dissociation to hydrogen and Sulfur reduces its toxic characteristics
and make economical benefits.
Abstract: Ultrastructure of duodenum mucosa of irradiated rat
was studied versus dose rate of irradiation following exposure to
gamma rays from 60-Cobalt source. The animals were whole body
irradiated at two dose rates (1 Gy.mn-1 and 1 Gy.h-1) and three total
doses (1, 2 or 4 Gy) for each dose rate. 24 or 48 h after irradiation,
their small intestine was removed and samples of duodenum were
processed for observations under a transmission electron microscopy.
Samples of duodenum mucosa of control rats were processed in the
same way. For the lower dose rate of 1 Gy.h-1, main lesions
characteristic of apoptosis were detected within irradiated enterocytes
at a total dose of 2 Gy and 24 h after exposure. Necrosis was noted in
the samples, 48 h after exposition. For the higher dose rate of 1
Gy.mn-1, fewer changes were detected at all total doses 24 or 48 h
irradiation. Thus, it was shown that the appearance of radiationinduced
alterations varies not only with increasing total dose and
post-irradiation time but especially with decreasing dose rate.
Abstract: In this article, LQR based PID controller design for
3DOF helicopter system is investigated. The 3-DOF helicopter
system is a benchmark laboratory model having strongly nonlinear
characteristics and unstable dynamics which make the control of such
system a challenging task. This article first presents the mathematical
model of the 3DOF helicopter system and then illustrates the basic
idea and technical formulation for controller design. The paper
explains the simple approach for the approximation of PID design
parameters from the LQR controller gain matrix. The simulation
results show that the investigated controller has both static and
dynamic performance, therefore the stability and the quick control
effect can be obtained simultaneously for the 3DOF helicopter
system.
Abstract: A lot of recent research have spoken on the relation
between the increase of the homocysteinemia and some kinds of
cancer . For that, our study was based on the research of a possible
relation between the increase of the concentration of this amino-acid
in the plasma and the appearance of the disease of the Acute
Lymphoblastic Leukaemia in a part of Algerian children with Berber
origin in the East of Algeria . The study has done on 47 ill persons
with an average age of (09±06 ) years , with whom the disease has
diagnosed by blood and marrow examination in the hospital of blood
diseases in the CHU of Batna, and on 194 healthy witnesses of the
same age. The two groups were benefited by a dosage of the
concentration of the homocysteine vitamin B9 ,vitamin B12 , and
also of the study of special polymorphisms of indispensable enzymes
in the metabolism of this acid , and that by the use of the method (
Light cycler ) Real time PCR , on the following enzymes : MS (
C2756G ), MSR ( A66G ) ,MTHFR1 ( C677T ) and MTHFR2
(A1298C). The obtained results have revealed that the rate of the
homozygote muted genotype is the less frequent in the two groups ,
and that exist at list one genotype of each enzyme in the ill group and
in which the percentage exceed with remarkable way the same
genotype in the healthy group and we notice specially the muted
genotype GG of -the methionine synthetase-and the form TT of the
enzyme – methyline tetra hydrofolate reductase – We notice the
existence of considerable number of genotypes in the ill group lied
with characteristic increase of this Amino-acid ,and that for the
reduction of the biologic activity of these enzymes which become
inefficient in the transfer of the homocysteine into the methionine
and cause the diminution of the biologic activity of these enzymes
and with consequence the reduction of the percentage of methylic
radicals in the DNA of studied genes and that lead to the increase of
the activity and the capacity of transcription , and it-s so probably
that this last one is one of the factors of this disease especially if we
know that the specific check-up of vitamins is normal and similar in
the two groups , which ovoid the hypothesis of the reduction of
vitamins . We notice also that the heterozygote genotype is the less in
the sick category except the MTHFR2. Wild genotype is more
frequent in the witness group except MSR. Even these results are
partials; they open a new way in the genetic diagnosis of this
malicious disease which allow a precocious diagnosis and the use of
an effective and appropriated treatment in the same time.
Abstract: A design flow of multi-standard down-conversion
CMOS mixers for three modern standards: Global System Mobile,
Digital Enhanced Cordless Telephone and Universal Mobile
Telecommunication Systems is presented. Three active mixer-s
structures are studied. The first is based on the Gilbert cell which
gives a tolerable noise figure and linearity with a low conversion
gain. The second and third structures use the current bleeding and
charge injection techniques in order to increase the conversion gain.
An improvement of about 2 dB of the conversion gain is achieved
without a considerable degradation of the other characteristics. The
models used for noise figure, conversion gain and IIP3 used are
studied. This study describes the nature of trade-offs inherent in such
structures and gives insights that help in identifying which structure
is better for given conditions.
Abstract: A Finite Volume method based on Characteristic Fluxes for compressible fluids is developed. An explicit cell-centered resolution is adopted, where second and third order accuracy is provided by using two different MUSCL schemes with Minmod, Sweby or Superbee limiters for the hyperbolic part. Few different times integrator is used and be describe in this paper. Resolution is performed on a generic unstructured Cartesian grid, where solid boundaries are handled by a Cut-Cell method. Interfaces are explicitely advected in a non-diffusive way, ensuring local mass conservation. An improved cell cutting has been developed to handle boundaries of arbitrary geometrical complexity. Instead of using a polygon clipping algorithm, we use the Voxel traversal algorithm coupled with a local floodfill scanline to intersect 2D or 3D boundary surface meshes with the fixed Cartesian grid. Small cells stability problem near the boundaries is solved using a fully conservative merging method. Inflow and outflow conditions are also implemented in the model. The solver is validated on 2D academic test cases, such as the flow past a cylinder. The latter test cases are performed both in the frame of the body and in a fixed frame where the body is moving across the mesh. Adaptive Cartesian grid is provided by Paramesh without complex geometries for the moment.
Abstract: In textile industry, besides the conventional textile
products, technical textile goods, that have been brought external
functional properties into, are being developed for technical textile
industry. Especially these products produced with weaving
technology are widely preferred in areas such as sports, geology,
medical, automotive, construction and marine sectors. These textile
products are exposed to various stresses and large deformations under
typical conditions of use. At this point, sufficient and reliable data
could not be obtained with uniaxial tensile tests for determination of
the mechanical properties of such products due to mainly biaxial
stress state. Therefore, the most preferred method is a biaxial tensile
test method and analysis. These tests and analysis is applied to fabrics
with different functional features in order to establish the textile
material with several characteristics and mechanical properties of the
product. Planar biaxial tensile test, cylindrical inflation and bulge
tests are generally required to apply for textile products that are used
in automotive, sailing and sports areas and construction industry to
minimize accidents as long as their service life. Airbags, seat belts
and car tires in the automotive sector are also subject to the same
biaxial stress states, and can be characterized by same types of
experiments. In this study, in accordance with the research literature
related to the various biaxial test methods are compared. Results with
discussions are elaborated mainly focusing on the design of a biaxial
test apparatus to obtain applicable experimental data for developing a
finite element model. Sample experimental results on a prototype
system are expressed.
Abstract: Horizontal continuous casting is widely used to
produce semi-finished non-Ferrous products. Homogeneity in the
metallurgical characteristics and mechanical properties for this
product is vital for industrial application. In the present work, the
microstructure and mechanical properties of a horizontal continuous
cast two-phase brass billet have been studied. Impact strength and
hardness variations were examined and the phase composition and
porosity studied with image analysis software. Distinct differences in
mechanical properties were observed between the upper, middle and
lower parts of the billet, which are explained in terms of the
morphology and size of the phase in the microstructure. Hardness
variation in the length of billet is higher in upper area but impact
strength is higher in lower areas.
Abstract: The paper presents the results of a series of
experiments conducted on physical models of Quarter-circle
breakwater (QBW) in a two dimensional monochromatic wave
flume. The purpose of the experiments was to evaluate the reflection
coefficient Kr of QBW models of different radii (R) for different
submergence ratios (d/hc), where d is the depth of water and hc is the
height of the breakwater crest from the sea bed. The radii of the
breakwater models studied were 20cm, 22.5cm, 25cm, 27.5cm and
submergence ratios used varied from 1.067 to 1.667. The wave
climate off the Mangalore coast was used for arriving at the various
model wave parameters. The incident wave heights (Hi) used in the
flume varied from 3 to 18cm, and wave periods (T) ranged from 1.2 s
to 2.2 s. The water depths (d) of 40cm, 45cm and 50cm were used in
the experiments. The data collected was analyzed to compute
variation of reflection coefficient Kr=Hr/Hi (where Hr=reflected wave
height) with the wave steepness Hi/gT2 for various R/Hi
(R=breakwater radius) values. It was found that the reflection
coefficient increased as incident wave steepness increased. Also as
wave height decreases reflection coefficient decreases and as
structure radius R increased Kr decreased slightly.
Abstract: The effect of streamwise conduction on the thermal
characteristics of forced convection for nanofluidic flow in
rectangular microchannel heat sinks under isothermal wall has been
investigated. By applying the fin approach, models with and without
streamwise conduction term in the energy equation were developed
for hydrodynamically and thermally fully-developed flow. These two
models were solved to obtain closed form analytical solutions for the
nanofluid and solid wall temperature distributions and the analysis
emphasized details of the variations induced by the streamwise
conduction on the nanofluid heat transport characteristics. The effects
of the Peclet number, nanoparticle volume fraction, thermal
conductivity ratio on the thermal characteristics of forced convection
in microchannel heat sinks are analyzed. Due to the anomalous
increase in the effective thermal conductivity of nanofluid compared
to its base fluid, the effect of streamwise conduction is expected to be
more significant. This study reveals the significance of the effect of
streamwise conduction under certain conditions of which the
streamwise conduction should not be neglected in the forced
convective heat transfer analysis of microchannel heat sinks.
Abstract: Implementing Information Technology/ Information
System (IT/IS) is critical for every industry as its potential benefits
have been to motivate many industries including the Malaysian
construction industry to invest in it. To successfully implement IT/IS
has become the major concern for every organisation. Identifying the
critical success factors (CSFs) has become the main agenda for
researchers, academicians and practitioners due to the wide number
of failures reported. This research paper seeks to identify the CSFs
that influence the successful implementation of IT/IS in construction
industry in Malaysia. Limited factors relating to people issue will be
highlighted here to showcase some as it becomes one of the major
contributing factors to the failure. Three (3) organisations have
participated in this study. Semi-structured interviews are employed as
they offer sufficient flexibility to ensure that all relevant factors are
covered. Several key issues contributing to successful
implementations of IT/IS are identified. The results of this study
reveal that top management support, communication, user
involvement, IT staff roles and responsibility, training/skills, leader/
IT Leader, organisation culture, knowledge/ experience, motivation,
awareness, focus and ambition, satisfaction, teamwork/ collaboration,
willingness to change, attitude, commitment, management style,
interest in IT, employee behaviour towards collaborative
environment, trust, interpersonal relationship, personal characteristic
and competencies are significantly associated with the successful
implementations of IT/IS. It is anticipated that this study will create
awareness and contribute to a better understanding amongst
construction industry players and will assist them to successfully
implement IT/IS.
Abstract: The flow and heat transfer characteristics for natural
convection along an inclined plate in a saturated porous medium with
an applied magnetic field have been studied. The fluid viscosity has
been assumed to be an inverse function of temperature. Assuming
temperature vary as a power function of distance. The transformed
ordinary differential equations have solved by numerical integration
using Runge-Kutta method. The velocity and temperature profile
components on the plate are computed and discussed in detail for
various values of the variable viscosity parameter, inclination angle,
magnetic field parameter, and real constant (λ). The results have also
been interpreted with the aid of tables and graphs. The numerical
values of Nusselt number have been calculated for the mentioned
parameters.
Abstract: In this paper methodology to exploit creeping wave
for body area network BAN communication reliability are described.
Creeping wave propagation effects are visualized & analyzed.
During this work Dipole, IA antennas various antennas were
redesigned using existing designs and their propagation
characteristics were verified for optimum performance when used on
BANs. These antennas were then applied on body shapes-including
rectangular, spherical and cylindrical so that all the effects of actual
human body can be taken nearly into account. Parametric simulation
scheme was devised so that on Body channel characterization can be
visualized at front, curved and back region. In the next phase
multiple inputs multiple output MIMO scheme was introduced where
virtual antennas were used in order to diminish the effects of
antennas on the propagation of waves. Results were, extracted and
analyzed at different heights. Finally based on comparative
measurement and analysis it was concluded that on body propagation
can be exploited to gain spatial diversity.
Abstract: Circular tubes have been widely used as structural
members in engineering application. Therefore, its collapse behavior
has been studied for many decades, focusing on its energy absorption
characteristics. In order to predict the collapse behavior of members,
one could rely on the use of finite element codes or experiments.
These tools are helpful and high accuracy but costly and require
extensive running time. Therefore, an approximating model of tubes
collapse mechanism is an alternative for early step of design. This
paper is also aimed to develop a closed-form solution of thin-walled
circular tube subjected to bending. It has extended the Elchalakani et
al.-s model (Int. J. Mech. Sci.2002; 44:1117-1143) to include the
rate of energy dissipation of rolling hinge in the circumferential
direction. The 3-D geometrical collapse mechanism was analyzed by
adding the oblique hinge lines along the longitudinal tube within the
length of plastically deforming zone. The model was based on the
principal of energy rate conservation. Therefore, the rates of internal
energy dissipation were calculated for each hinge lines which are
defined in term of velocity field. Inextensional deformation and
perfect plastic material behavior was assumed in the derivation of
deformation energy rate. The analytical result was compared with
experimental result. The experiment was conducted with a number of
tubes having various D/t ratios. Good agreement between analytical
and experiment was achieved.
Abstract: In recent years, the underground water sources in
southern Taiwan have become salinized because of saltwater
intrusions. This study explores the adsorption characteristics of
activated carbon on salinizing inorganic salts using isothermal
adsorption experiments and provides a model analysis. The
temperature range for the isothermal adsorption experiments ranged
between 5 to 45 ℃, and the amount adsorbed varied between 28.21 to
33.87 mg/g. All experimental data of adsorption can be fitted to both
the Langmuir and the Freundlich models. The thermodynamic
parameters for per chlorate onto granular activated carbon were
calculated as -0.99 to -1.11 kcal/mol for DG°, -0.6 kcal/mol for DH°,
and 1.21 to 1.84 kcal/mol for DS°. This shows that the adsorption
process of granular activated carbon is spontaneously exothermic. The
observation of adsorption behaviors under low ionic strength, low pH
values, and low temperatures is beneficial to the adsorption removal of
perchlorate with granular activated carbon.
Abstract: The present work describes a computational study of
aerodynamic characteristics of GLC305 airfoil clean and with 16.7
min ice shape (rime 212) and 22.5 min ice shape (glaze 944).The
performance of turbulence models SA, Kε, Kω Std, and Kω SST
model are observed against experimental flow fields at different
Mach numbers 0.12, 0.21, 0.28 in a range of Reynolds numbers
3x106, 6x106, and 10.5x106 on clean and iced aircraft airfoil
GLC305. Numerical predictions include lift, drag and pitching
moment coefficients at different Mach numbers and at different angle
of attacks were done. Accuracy of solutions with respect to the
effects of turbulence models, variation of Mach number, initial
conditions, grid resolution and grid spacing near the wall made the
study much sensitive. Navier Stokes equation based computational
technique is used. Results are very close to the experimental results.
It has seen that SA and SST models are more efficient than Kε and
Kω standard in under study problem.
Abstract: This paper has as its main aim to analyse how
corporate web pages can become an essential tool in order to detect
strategic trends by firms or sectors, and even a primary source for
benchmarking. This technique has made it possible to identify the key
issues in the strategic management of the most excellent large Spanish
firms and also to describe trends in their long-range planning, a way of
working that can be generalised to any country or firm group. More
precisely, two objectives were sought. The first one consisted in showing
the way in which corporate websites make it possible to obtain direct
information about the strategic variables which can define firms. This
tool is dynamic (since web pages are constantly updated) as well as
direct and reliable, since the information comes from the firm itself, not
from comments of third parties (such as journalists, academicians,
consultants...). When this information is analysed for a group of firms,
one can observe their characteristics in terms of both managerial tasks
and business management. As for the second objective, the methodology
proposed served to describe the corporate profile of the large Spanish
enterprises included in the Ibex35 (the Ibex35 or Iberia Index is the
reference index in the Spanish Stock Exchange and gathers periodically
the 35 most outstanding Spanish firms). An attempt is therefore made to
define the long-range planning that would be characteristic of the largest
Spanish firms.
Abstract: Clustering is one of an interesting data mining topics
that can be applied in many fields. Recently, the problem of cluster
analysis is formulated as a problem of nonsmooth, nonconvex optimization,
and an algorithm for solving the cluster analysis problem
based on nonsmooth optimization techniques is developed. This
optimization problem has a number of characteristics that make it
challenging: it has many local minimum, the optimization variables
can be either continuous or categorical, and there are no exact
analytical derivatives. In this study we show how to apply a particular
class of optimization methods known as pattern search methods
to address these challenges. These methods do not explicitly use
derivatives, an important feature that has not been addressed in
previous studies. Results of numerical experiments are presented
which demonstrate the effectiveness of the proposed method.