Abstract: In this research, Response Surface Methodology (RSM) is used to investigate the effect of four controllable input variables namely: discharge current, pulse duration, pulse off time and applied voltage Surface Roughness (SR) of on Electrical Discharge Machined surface. To study the proposed second-order polynomial model for SR, a Central Composite Design (CCD) is used to estimation the model coefficients of the four input factors, which are alleged to influence the SR in Electrical Discharge Machining (EDM) process. Experiments were conducted on AISI D2 tool steel with copper electrode. The response is modeled using RSM on experimental data. The significant coefficients are obtained by performing Analysis of Variance (ANOVA) at 5% level of significance. It is found that discharge current, pulse duration, and pulse off time and few of their interactions have significant effect on the SR. The model sufficiency is very satisfactory as the Coefficient of Determination (R2) is found to be 91.7% and adjusted R2-statistic (R2 adj ) 89.6%.
Abstract: Eight heavy metals (Cu, Cr, Zn, Hg, Pb, Cd, Ni and As) were analyzed in sediment samples in the dry and wet seasons from November 2009 to October 2010 in West Port of Peninsular Malaysia. The heavy metal concentrations (mg/kg dry weight) were ranged from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. Metals concentrations in dry season were higher than the rainy season except in cupper and chromium. Analysis of variance with Statistical Analysis System (SAS) shows that the mean concentration of metals in the two seasons (α level=0.05) are not significantly different which shows that the metals were held firmly in the matrix of sediment. Also there are significant differences between control point station with other stations. According to the Interim Sediment Quality guidelines (ISQG), the metal concentrations are moderately polluted, except in arsenic which shows the highest level of pollution.
Abstract: Simultaneous Saccharification and Fermentation (SSF) of sugarcane bagasse by cellulase and Pachysolen tannophilus MTCC *1077 were investigated in the present study. Important process variables for ethanol production form pretreated bagasse were optimized using Response Surface Methodology (RSM) based on central composite design (CCD) experiments. A 23 five level CCD experiments with central and axial points was used to develop a statistical model for the optimization of process variables such as incubation temperature (25–45°) X1, pH (5.0–7.0) X2 and fermentation time (24–120 h) X3. Data obtained from RSM on ethanol production were subjected to the analysis of variance (ANOVA) and analyzed using a second order polynomial equation and contour plots were used to study the interactions among three relevant variables of the fermentation process. The fermentation experiments were carried out using an online monitored modular fermenter 2L capacity. The processing parameters setup for reaching a maximum response for ethanol production was obtained when applying the optimum values for temperature (32°C), pH (5.6) and fermentation time (110 h). Maximum ethanol concentration (3.36 g/l) was obtained from 50 g/l pretreated sugarcane bagasse at the optimized process conditions in aerobic batch fermentation. Kinetic models such as Monod, Modified Logistic model, Modified Logistic incorporated Leudeking – Piret model and Modified Logistic incorporated Modified Leudeking – Piret model have been evaluated and the constants were predicted.
Abstract: Food safety is an important concern for holiday
makers in foreign and unfamiliar tourist destinations. In fact, risk
from food in these tourist destinations has an influence on tourist
perception. This risk can potentially affect physical health and lead to
an inability to pursue planned activities. The objective of this paper
was to compare foreign tourists- demographics including gender, age
and education level, with the level of perceived risk towards food
safety. A total of 222 foreign tourists during their stay at Khao San
Road in Bangkok were used as the sample. Independent- samples ttest,
analysis of variance, and Least Significant Difference or LSD
post hoc test were utilized. The findings revealed that there were few
demographic differences in level of perceived risk among the foreign
tourists. The post hoc test indicated a significant difference among
the old and the young tourists, and between the higher and lower
level of education. Ranks of tourists- perceived risk towards food
safety unveiled some interesting results. Tourists- perceived risk of
food safety in established restaurants can be ranked as i) cleanliness
of dining utensils, ii) sanitation of food preparation area, and iii)
cleanliness of food seasoning and ingredients. Whereas, the tourists-
perceived risk of food safety in street food and drink can be ranked
as i) cleanliness of stalls and pushcarts, ii) cleanliness of food sold,
and iii) personal hygiene of street food hawkers or vendors.
Abstract: Grey mold on grape is caused by the fungus Botrytis
cinerea Pers. Trichodex WP, a new biofungicide, that contains fungal
spores of Trichoderma harzianum Rifai, was used for biological
control of Grey mold on grape. The efficacy of Trichodex WP has
been reported from many experiments. Experiments were carried out
in the locality – Banatski Karlovac, on grapevine species – talijanski
rizling. The trials were set according to instructions of methods
PP1/152(2) and PP1/17(3) , according to a fully randomized block
design. Phytotoxicity was estimated by PP methods 1/135(2), the
intensity of infection according to Towsend Heuberger , the
efficiency by Abbott, the analysis of variance with Duncan test and
PP/181(2). Application of Trichodex WP is limited to the first two
treatments. Other treatments are performed with the fungicides based
on a.i. procymidone, vinclozoline and iprodione.
Abstract: This questionnaire-based study, aimed to measure and
compare the awareness of English reading strategies among EFL
learners at Bangkok University (BU) classified by their gender, field
of study, and English learning experience. Proportional stratified
random sampling was employed to formulate a sample of 380 BU
students. The data were statistically analyzed in terms of the mean
and standard deviation. t-Test analysis was used to find differences in
awareness of reading strategies between two groups (-male and
female- /-science and social-science students). In addition, one-way
analysis of variance (ANOVA) was used to compare reading strategy
awareness among BU students with different lengths of English
learning experience. The results of this study indicated that the
overall awareness of reading strategies of EFL learners at BU was at
a high level (ðÑ = 3.60) and that there was no statistically significant
difference between males and females, and among students who have
different lengths of English learning experience at the significance
level of 0.05. However, significant differences among students
coming from different fields of study were found at the same level of
significance.
Abstract: The traditional Failure Mode and Effects Analysis
(FMEA) uses Risk Priority Number (RPN) to evaluate the risk level
of a component or process. The RPN index is determined by
calculating the product of severity, occurrence and detection indexes.
The most critically debated disadvantage of this approach is that
various sets of these three indexes may produce an identical value of
RPN. This research paper seeks to address the drawbacks in
traditional FMEA and to propose a new approach to overcome these
shortcomings. The Risk Priority Code (RPC) is used to prioritize
failure modes, when two or more failure modes have the same RPN.
A new method is proposed to prioritize failure modes, when there is a
disagreement in ranking scale for severity, occurrence and detection.
An Analysis of Variance (ANOVA) is used to compare means of
RPN values. SPSS (Statistical Package for the Social Sciences)
statistical analysis package is used to analyze the data. The results
presented are based on two case studies. It is found that the proposed
new methodology/approach resolves the limitations of traditional
FMEA approach.
Abstract: This paper deals optimized model to investigate the
effects of peak current, pulse on time and pulse off time in EDM performance on material removal rate of titanium alloy utilizing copper tungsten as electrode and positive polarity of the electrode. The experiments are carried out on Ti6Al4V. Experiments were
conducted by varying the peak current, pulse on time and pulse off time. A mathematical model is developed to correlate the influences of these variables and material removal rate of workpiece. Design of
experiments (DOE) method and response surface methodology
(RSM) techniques are implemented. The validity test of the fit and adequacy of the proposed models has been carried out through
analysis of variance (ANOVA). The obtained results evidence that as
the material removal rate increases as peak current and pulse on time
increases. The effect of pulse off time on MRR changes with peak ampere. The optimum machining conditions in favor of material removal rate are verified and compared. The optimum machining
conditions in favor of material removal rate are estimated and verified with proposed optimized results. It is observed that the developed model is within the limits of the agreeable error (about
4%) when compared to experimental results. This result leads to desirable material removal rate and economical industrial machining to optimize the input parameters.
Abstract: The aim of this research is to evaluate surface
roughness and develop a multiple regression model for surface roughness as a function of cutting parameters during the turning of
flame hardened medium carbon steel with TiN-Al2O3-TiCN coated inserts. An experimental plan of work and signal-to-noise ratio (S/N)
were used to relate the influence of turning parameters to the
workpiece surface finish utilizing Taguchi methodology. The effects
of turning parameters were studied by using the analysis of variance (ANOVA) method. Evaluated parameters were feed, cutting speed,
and depth of cut. It was found that the most significant interaction among the considered turning parameters was between depth of cut and feed. The average surface roughness (Ra) resulted by TiN-Al2O3-
TiCN coated inserts was about 2.44 μm and minimum value was 0.74 μm. In addition, the regression model was able to predict values for surface roughness in comparison with experimental values within
reasonable limit.
Abstract: Moulded parts contribute to more than 70% of
components in products. However, common defects particularly in
plastic injection moulding exist such as: warpage, shrinkage, sink
marks, and weld lines. In this paper Taguchi experimental design
methods are applied to reduce the warpage defect of thin plate
Acrylonitrile Butadiene Styrene (ABS) and are demonstrated in two
levels; namely, orthogonal arrays of Taguchi and the Analysis of
Variance (ANOVA). Eight trials have been run in which the optimal
parameters that can minimize the warpage defect in factorial
experiment are obtained. The results obtained from ANOVA
approach analysis with respect to those derived from MINITAB
illustrate the most significant factors which may cause warpage in
injection moulding process. Moreover, ANOVA approach in
comparison with other approaches like S/N ratio is more accurate and
with the interaction of factors it is possible to achieve higher and the
better outcomes.
Abstract: The primary objective of this study is to test whether
there is any difference in performance between funded and nonfunded
registered charity organizations. In this study, performance as
the dependent variable is measured using total donations. Using a
sample of 101 charity organizations registered with the Registry of
Society, analysis of variance (ANOVA) results indicate that there is a
difference in financial performance between funded and non-funded
charity organizations. The study provides empirical evidence to
resource providers and the policy makers in scrutinizing the decision
to disburse their funds and resources to these charity organizations.
Abstract: This paper describes the shape optimization of impeller
blades for a anti-heeling bidirectional axial flow pump used in ships.
In general, a bidirectional axial pump has an efficiency much lower
than the classical unidirectional pump because of the symmetry of the
blade type. In this paper, by focusing on a pump impeller, the shape of
blades is redesigned to reach a higher efficiency in a bidirectional axial
pump. The commercial code employed in this simulation is CFX v.13.
CFD result of pump torque, head, and hydraulic efficiency was
compared. The orthogonal array (OA) and analysis of variance
(ANOVA) techniques and surrogate model based optimization using
orthogonal polynomial, are employed to determine the main effects
and their optimal design variables. According to the optimal design,
we confirm an effective design variable in impeller blades and explain
the optimal solution, the usefulness for satisfying the constraints of
pump torque and head.
Abstract: In this study, participants with adjustment disorder with depressed mood (aged 18-54 years) with mild depression (N=18), severe depression (N=12) were compared with healthy controls (N=20) on the Multidimensional Aptitude Battery (MAB) a cognitive performance test. Using One Way Analysis of Variance and Matched Sample t-test. The results of the analysis shows that severely depressed participants performed poorly on the cognitive performance test relative to controls, however there were no significant differences on the cognitive performance test scores between the severely depressed and the mildly depressed. In addition, performance on the non-verbal performance subtest was poorer than that of the verbal subtest, suggesting that depression affects the executive functions of the person.
Abstract: The aims of this study were to compare the
differences of being good membership behavior among faculties and
staffs of Suan Sunandha Rajabhat University with different sex, age,
income, education, marital status, and working period, and
investigate the relationships between organizational commitment and
being good membership behavior. The research methodology
employed a questionnaire as a quantitative method. The respondents
were 305 faculties and staffs of Suan Sunandha Rajabhat University.
This research used Percentage, Mean, Standard Deviation, t-test,
One-Way ANOVA Analysis of Variance, and Pearson’s Product
Moment Correlation Coefficient in data analysis. The results showed
that organizational commitment among faculties and staffs of Suan
Sunandha Rajabhat University was at a high level. In addition,
differences in sex, age, income, education, marital status, and
working period revealed differences in being good membership
behavior. The results also indicated that organizational commitment
was significantly related to being good membership behavior.
Abstract: Enzymatic hydrolysis of starch from natural sources
finds potential application in commercial production of alcoholic
beverage and bioethanol. In this study the effect of starch
concentration, temperature, time and enzyme concentration were
studied and optimized for hydrolysis of cassava (Manihot esculenta)
starch powder (of mesh 80/120) into glucose syrup by immobilized
(using Polyacrylamide gel) a-amylase using central composite
design. The experimental result on enzymatic hydrolysis of cassava
starch was subjected to multiple linear regression analysis using
MINITAB 14 software. Positive linear effect of starch concentration,
enzyme concentration and time was observed on hydrolysis of
cassava starch by a-amylase. The statistical significance of the model
was validated by F-test for analysis of variance (p < 0.01). The
optimum value of starch concentration temperature, time and enzyme
concentration were found to be 4.5% (w/v), 45oC, 150 min, and 1%
(w/v) enzyme. The maximum glucose yield at optimum condition
was 5.17 mg/mL.
Abstract: Twelve lactating Etawah Crossedbred goats were used
in this study. Goat feed consisted of Cally andra callothyrsus,
Pennisetum purpureum, wheat bran and dried fermented cassava
peel. The cassava peels were fermented with a traditional culture
called “ragi tape" (mixed culture of Saccharomyces cerevisae,
Aspergillus sp, Candida, Hasnula and Acetobacter). The goats were
divided into 2 groups (Control and Treated) of six does. The
experimental diet of the Control group consisted of 70% of roughage
(fresh Callyandra callothyrsus and Pennisetum purpureum 60:40)
and 30% of wheat bran on dry matter (DM) base. In the Treated
group 30% of wheat bran was replaced with dried fermented cassava
peels. Data were statistically analyzed using analysis of variance
followed SPSS program. The concentration of HCN in fermented
cassava peel decreased to non toxic level. Nutrient composition of
dried fermented cassava peel consisted of 85.75% dry matter;
5.80% crude protein and 82.51% total digestible nutrien (TDN).
Substitution of 30% of wheat bran with dried fermented cassava peel
in the diet had no effect on dry matter and organic matter intake but
significantly (P< 0.05) decreased crude protein and TDN
consumption as well as milk yields and milk composition. The study
recommended to reduced the level of substitution to less than 30% of
concentrates in the diet in order to avoid low nutrient intake and milk
production of goats.
Abstract: Burnishing is a method of finishing and hardening
machined parts by plastic deformation of the surface. Experimental
work based on central composite second order rotatable design has
been carried out on a lathe machine to establish the effects of ball
burnishing parameters on the surface roughness of brass material.
Analysis of the results by the analysis of variance technique and the
F-test show that the parameters considered, have significant effects
on the surface roughness.
Abstract: Concerns about low levels of children-s physical activity and motor skill development, prompted the Ministry of Education to trial a physical activity pilot project (PAPP) in 16 New Zealand primary schools. The project comprised professional development and training in physical education for lead teachers and introduced four physical activity coordinators to liaise with and increase physical activity opportunities in the pilot schools. A survey of generalist teachers (128 baseline, 155 post-intervention) from these schools looked at timetabled physical activity sessions and issues related to teaching physical education. The authors calculated means and standard deviations of data relating to timetabled PE sessions and used a one-way analysis of variance to determine significant differences. Results indicated time devoted to physical activity related subjects significantly increased over the course of the intervention. Teacher-s reported improved confidence and competence, which resulted in an improvement in quality physical education delivered more often.
Abstract: An experiment was conducted with 80 unsexed
broilers of the Arbor Acress strain to determine the capability of a
carrot and fruit juice wastes mixture (carrot, apple, manggo, avocado,
orange, melon and Dutch egg plant) in the same proportion for
replacing corn in broiler diet. This study involved a completely
randomized design (CRD) with 5 treatments (0, 5, 10, 15, and 20% of
juice wastes mixture in diets) and 4 replicates per treatment. Diets
were isonitrogenous (22% crude protein) and isocaloric (3000 kcal/kg
diet). Measured variables were feed consumption, average daily
gain, feed conversion, as well as percentages of abdominal fat pad,
carcass, digestive organs (liver, pancreas and gizzard), and heart.
Data were analyzed by analysis of variance for CRD. Increasing
juice wastes mixture levels in diets increased feed consumption
(P
Abstract: Multiprocessor task scheduling is a NP-hard problem and Genetic Algorithm (GA) has been revealed as an excellent technique for finding an optimal solution. In the past, several methods have been considered for the solution of this problem based on GAs. But, all these methods consider single criteria and in the present work, minimization of the bi-criteria multiprocessor task scheduling problem has been considered which includes weighted sum of makespan & total completion time. Efficiency and effectiveness of genetic algorithm can be achieved by optimization of its different parameters such as crossover, mutation, crossover probability, selection function etc. The effects of GA parameters on minimization of bi-criteria fitness function and subsequent setting of parameters have been accomplished by central composite design (CCD) approach of response surface methodology (RSM) of Design of Experiments. The experiments have been performed with different levels of GA parameters and analysis of variance has been performed for significant parameters for minimisation of makespan and total completion time simultaneously.