Abstract: During the last few decades, the continuously increasing demand for accurate and reliable magnetic measurements has paved the way for the development of different types of magnetic sensing systems as well as different measurement techniques. Sensor sensitivity and linearity, signal-to-noise ratio, measurement range, cross-talk between sensors in multi-sensor applications are only some of the aspects that have been examined in the past. In this paper, a fully analog closed loop system in order to optimize the performance of AMR sensors has been developed. The operation of the proposed system has been tested using a Helmholtz coil calibration setup in order to control both the amplitude and direction of magnetic field in the vicinity of the AMR sensor. Experimental testing indicated that improved linearity of sensor response, as well as low noise levels can be achieved, when the system is employed.
Abstract: To acquire accurate ship motions at the center of gravity, a single low-cost inertial sensor is utilized and applied on board to measure ship oscillating motions. As observations, the three axes accelerations and three axes rotational rates provided by the sensor are used. The mathematical model of processing the observation data includes determination of the distance vector between the sensor and the center of gravity in x, y, and z directions. After setting up the transfer matrix from sensor’s own coordinate system to the ship’s body frame, an extended Kalman filter is applied to deal with nonlinearities between the ship motion in the body frame and the observation information in the sensor’s frame. As a side effect, the method eliminates sensor noise and other unwanted errors. Results are not only roll and pitch, but also linear motions, in particular heave and surge at the center of gravity. For testing, we resort to measurements recorded on a small vessel in a well-defined sea state. With response amplitude operators computed numerically by a commercial software (Seaway), motion characteristics are estimated. These agree well with the measurements after processing with the suggested method.
Abstract: Surface topography plays a significant role in the functional performance of engineered parts. It is important to have a control on the surface geometry and understanding on the surface details to get the desired performance. Hence, in the current research contribution, a non-contact micro-texturing technique has been explored and developed. The technique involves ultrasonic excitation of a tool as a prime source of surface texturing for aluminum alloy workpieces. The specimen surface is polished first and is then immersed in a liquid bath containing 10% weight concentration of Ti6Al4V grade 5 spherical powders. A submerged slurry jet is used to recirculate the spherical powders under the ultrasonic horn which is excited at an ultrasonic frequency and amplitude of 40 kHz and 70 µm respectively. The distance between the horn and workpiece surface was remained fixed at 200 µm using a precision control stage. Texturing effects were investigated for different process timings of 1, 3 and 5 s. Thereafter, the specimens were cleaned in an ultrasonic bath for 5 mins to remove loose debris on the surface. The developed surfaces are characterized by optical and contact surface profiler. The optical microscopic images show a texture of circular spots on the workpiece surface indented by titanium spherical balls. Waviness patterns obtained from contact surface profiler supports the texturing effect produced from the proposed technique. Furthermore, water droplet tests were performed to show the efficacy of the proposed technique to develop hydrophilic surfaces and to quantify the texturing effect produced.
Abstract: The influence of inhomogeneities of plasma and statistical characteristics on the propagation of signal is very actual in wireless communication systems. While propagating in the media, the deformation and evaluation of the signal in time and space take place and on the receiver we get a deformed signal. The present article is dedicated to studying the space-time evolution of rectangular, sinusoidal, exponential and bi-exponential impulses via numerical experiment in the collisional, cold plasma. The presented method is not based on the Fourier-presentation of the signal. Analytically, we have received the general image depicting the space-time evolution of the radio impulse amplitude that gives an opportunity to analyze the concrete results in the case of primary impulse.
Abstract: Propagation of nonlinear acoustic wave in dense electron-positron (e-p) plasmas in the presence of an external magnetic field and stationary ions (to neutralize the plasma background) is studied. By means of the quantum hydrodynamics model and applying the reductive perturbation method, the Zakharov-Kuznetsov equation is derived. Using the bifurcation theory of planar dynamical systems, the compressive structure of electrostatic solitary wave and periodic travelling waves is found. The numerical results show how the ion density ratio, the ion cyclotron frequency, and the direction cosines of the wave vector affect the nonlinear electrostatic travelling waves. The obtained results may be useful to better understand the obliquely nonlinear electrostatic travelling wave of small amplitude localized structures in dense magnetized quantum e-p plasmas and may be applicable to study the particle and energy transport mechanism in compact stars such as the interior of massive white dwarfs etc.
Abstract: Non-Newtonian fluid properties can change the flow
behaviour significantly, its prediction is more difficult when thermal
effects come into play. Hence, the focal point of this work is the
wake flow behind a heated circular cylinder in the laminar vortex
shedding regime for thermo-viscous shear thinning fluids. In the case
of isothermal flows of Newtonian fluids the vortex shedding regime
is characterised by a distinct Reynolds number and an associated
Strouhal number. In the case of thermo-viscous shear thinning
fluids the flow regime can significantly change in dependence of
the temperature of the viscous wall of the cylinder. The Reynolds
number alters locally and, consequentially, the Strouhal number
globally. In the present CFD study the temperature dependence of
the Reynolds and Strouhal number is investigated for the flow of a
Carreau fluid around a heated cylinder. The temperature dependence
of the fluid viscosity has been modelled by applying the standard
Williams-Landel-Ferry (WLF) equation. In the present simulation
campaign thermal boundary conditions have been varied over a
wide range in order to derive a relation between dimensionless heat
transfer, Reynolds and Strouhal number. Together with the shear
thinning due to the high shear rates close to the cylinder wall
this leads to a significant decrease of viscosity of three orders of
magnitude in the nearfield of the cylinder and a reduction of two
orders of magnitude in the wake field. Yet the shear thinning effect
is able to change the flow topology: a complex K´arm´an vortex street
occurs, also revealing distinct characteristic frequencies associated
with the dominant and sub-dominant vortices. Heating up the cylinder
wall leads to a delayed flow separation and narrower wake flow,
giving lesser space for the sequence of counter-rotating vortices. This
spatial limitation does not only reduce the amplitude of the oscillating
wake flow it also shifts the dominant frequency to higher frequencies,
furthermore it damps higher harmonics. Eventually the locally heated
wake flow smears out. Eventually, the CFD simulation results of the
systematically varied thermal flow parameter study have been used
to describe a relation for the main characteristic order parameters.
Abstract: In the paper we make linear and non-linear stability
analyses of Rayleigh-Bénard convection of a Newtonian nanoliquid
in a rotating medium (called as Rayleigh-Bénard-Taylor convection).
Rigid-rigid isothermal boundaries are considered for investigation.
Khanafer-Vafai-Lightstone single phase model is used for studying
instabilities in nanoliquids. Various thermophysical properties of
nanoliquid are obtained using phenomenological laws and mixture
theory. The eigen boundary value problem is solved for the Rayleigh
number using an analytical method by considering trigonometric
eigen functions. We observe that the critical nanoliquid Rayleigh
number is less than that of the base liquid. Thus the onset of
convection is advanced due to the addition of nanoparticles. So,
increase in volume fraction leads to advanced onset and thereby
increase in heat transport. The amplitudes of convective modes
required for estimating the heat transport are determined analytically.
The tri-modal standard Lorenz model is derived for the steady state
assuming small scale convective motions. The effect of rotation on
the onset of convection and on heat transport is investigated and
depicted graphically. It is observed that the onset of convection is
delayed due to rotation and hence leads to decrease in heat transport.
Hence, rotation has a stabilizing effect on the system. This is due to
the fact that the energy of the system is used to create the component
V. We observe that the amount of heat transport is less in the case
of rigid-rigid isothermal boundaries compared to free-free isothermal
boundaries.
Abstract: Sub-Nyquist sampling jamming method (SNSJ) is a well known deception jamming method for inverse synthetic aperture radar (ISAR). However, the anti-decoy of the SNSJ method performs easier since the amplitude of the false-target images are weaker than the real-target image; the false-target images always lag behind the real-target image, and all targets are located in the same cross-range. In order to overcome the drawbacks mentioned above, a simple modulation based on SNSJ (M-SNSJ) is presented in this paper. The method first uses amplitude modulation factor to make the amplitude of the false-target images consistent with the real-target image, then uses the down-range modulation factor and cross-range modulation factor to make the false-target images move freely in down-range and cross-range, respectively, thus the capacity of deception is improved. Finally, the simulation results on the six available combinations of three modulation factors are given to illustrate our conclusion.
Abstract: Conditions corresponding to the unconditional stability
of convection in a mechanically anisotropic fluid saturated porous
medium of infinite horizontal extent are determined. The medium
is heated from below and its bounding surfaces are subjected to
temperature modulation which consists of a steady part and a
time periodic oscillating part. The Brinkman model is employed
in the momentum equation with the Bousinessq approximation.
The stability region is found for arbitrary values of modulational
frequency and amplitude using the energy method. Higher order
numerical computations are carried out to find critical boundaries
and subcritical instability regions more accurately.
Abstract: A local nonlinear stability analysis using a eight-mode
expansion is performed in arriving at the coupled amplitude equations
for Rayleigh-Bénard-Brinkman convection (RBBC) in the presence
of LTNE effects. Streamlines and isotherms are obtained in the
two-dimensional unsteady finite-amplitude convection regime. The
parameters’ influence on heat transport is found to be more
pronounced at small time than at long times. Results of the
Rayleigh-Bénard convection is obtained as a particular case of
the present study. Additional modes are shown not to significantly
influence the heat transport thus leading us to infer that five minimal
modes are sufficient to make a study of RBBC. The present problem
that uses rolls as a pattern of manifestation of instability is a needed
first step in the direction of making a very general non-local study of
two-dimensional unsteady convection. The results may be useful in
determining the preferred range of parameters’ values while making
rheometric measurements in fluids to ascertain fluid properties such
as viscosity. The results of LTE are obtained as a limiting case of
the results of LTNE obtained in the paper.
Abstract: The Gravity Recovery and Climate Experiment (GRACE) has been a very successful project in determining math redistribution within the Earth system. Large deformations caused by earthquakes are in the high frequency band. Unfortunately, GRACE is only capable to provide reliable estimate at the low-to-medium frequency band for the gravitational changes. In this study, we computed the gravity changes after the 2012 Mw8.6 Indian Ocean earthquake off-Sumatra using the GRACE Level-2 monthly spherical harmonic (SH) solutions released by the University of Texas Center for Space Research (UTCSR). Moreover, we calculated gravity changes using different fault models derived from teleseismic data. The model predictions showed non-negligible discrepancies in gravity changes. However, after removing high-frequency signals, using Gaussian filtering 350 km commensurable GRACE spatial resolution, the discrepancies vanished, and the spatial patterns of total gravity changes predicted from all slip models became similar at the spatial resolution attainable by GRACE observations, and predicted-gravity changes were consistent with the GRACE-detected gravity changes. Nevertheless, the fault models, in which give different slip amplitudes, proportionally lead to different amplitude in the predicted gravity changes.
Abstract: Rayleigh-B´enard convection of a nanoliquid in shallow, square and tall enclosures is studied using the Khanafer-Vafai-Lightstone single-phase model. The thermophysical properties of water, copper, copper-oxide, alumina, silver and titania at 3000 K under stagnant conditions that are collected from literature are used in calculating thermophysical properties of water-based nanoliquids. Phenomenological laws and mixture theory are used for calculating thermophysical properties. Free-free, rigid-rigid and rigid-free boundary conditions are considered in the study. Intractable Lorenz model for each boundary combination is derived and then reduced to the tractable Ginzburg-Landau model. The amplitude thus obtained is used to quantify the heat transport in terms of Nusselt number. Addition of nanoparticles is shown not to alter the influence of the nature of boundaries on the onset of convection as well as on heat transport. Amongst the three enclosures considered, it is found that tall and shallow enclosures transport maximum and minimum energy respectively. Enhancement of heat transport due to nanoparticles in the three enclosures is found to be in the range 3% - 11%. Comparison of results in the case of rigid-rigid boundaries is made with those of an earlier work and good agreement is found. The study has limitations in the sense that thermophysical properties are calculated by using various quantities modelled for static condition.
Abstract: Mixed convection of Cu-water nanofluid in an enclosure
with thick wavy bottom wall has been investigated numerically.
A co-ordinate transformation method is used to transform the
computational domain into an orthogonal co-ordinate system. The
governing equations in the computational domain are solved through
a pressure correction based iterative algorithm. The fluid flow
and heat transfer characteristics are analyzed for a wide range
of Richardson number (0.1 ≤ Ri ≤ 5), nanoparticle volume
concentration (0.0 ≤ ϕ ≤ 0.2), amplitude (0.0 ≤ α ≤ 0.1) of
the wavy thick- bottom wall and the wave number (ω) at a fixed
Reynolds number. Obtained results showed that heat transfer rate
increases remarkably by adding the nanoparticles. Heat transfer rate
is dependent on the wavy wall amplitude and wave number and
decreases with increasing Richardson number for fixed amplitude
and wave number. The Bejan number and the entropy generation are
determined to analyze the thermodynamic optimization of the mixed
convection.
Abstract: Investigation of the discharges from the artificial charged water aerosol clouds in presence of the arrays of the model hydrometeors could help to receive the new data about the peculiarities of the return stroke formation between the thundercloud and the ground when the large volumes of the hail particles participate in the lightning discharge initiation and propagation stimulation. Artificial charged water aerosol clouds of the negative or positive polarity with the potential up to one million volts have been used. Hail has been simulated by the group of the conductive model hydrometeors of the different form. Parameters of the impulse current of the main stage of the discharge between the artificial positively and negatively charged water aerosol clouds and the ground in presence of the model hydrometeors array and of its corresponding electromagnetic radiation have been determined. It was established that the parameters of the array of the model hydrometeors influence on the parameters of the main stage of the discharge between the artificial thundercloud cell and the ground. The maximal values of the main stage current impulse parameters and the electromagnetic radiation registered by the plate antennas have been found for the array of the model hydrometeors of the cylinder revolution form for the negatively charged aerosol cloud and for the array of the hydrometeors of the plate rhombus form for the positively charged aerosol cloud, correspondingly. It was found that parameters of the main stage of the discharge between the artificial charged water aerosol cloud and the ground in presence of the model hydrometeor array of the different considered forms depend on the polarity of the artificial charged aerosol cloud. In average, for all forms of the investigated model hydrometeors arrays, the values of the amplitude and the current rise of the main stage impulse current and the amplitude of the corresponding electromagnetic radiation for the artificial charged aerosol cloud of the positive polarity were in 1.1-1.9 times higher than for the charged aerosol cloud of the negative polarity. Thus, the received results could indicate to the possible more important role of the big volumes of the large hail arrays in the thundercloud on the parameters of the return stroke for the positive lightning.
Abstract: This paper presents a 0.13-µm Complementary Metal-Oxide Semiconductor (CMOS) vector modulator for beamforming system. The vector modulator features a 360° phase and gain range of -10 dB to 10 dB with a root mean square phase and amplitude error of only 2.2° and 0.45 dB, respectively. These features make it a suitable for wireless backhaul system in the 5 GHz industrial, scientific, and medical (ISM) bands. It draws a current of 20.4 mA from a 1.2 V supply. The total chip size is 1.87x1.34 mm².
Abstract: Diffraction grating is periodic module used in many
engineering fields, its geometrical conception gives interesting
properties of diffraction and interferences, a uniform and periodic
diffraction grating consists of a number of identical apertures that are
equally spaced, in this case, the amplitude of intensity distribution
in the far field region is generally modulated by diffraction pattern
of single aperture. In this paper, we study the case of aperiodic
diffraction grating with identical rectangular apertures where theirs
coordinates are modeled by square root function, we elaborate a
computer simulation comparatively to the periodic array with same
length and we discuss the numerical results.
Abstract: In this paper, a theoretical investigation on the dynamic characteristics of one degree of freedom vibration system equipped with inerter of variable inertance, is presented. Differential equation of movement was solved under proper initial conditions in the case of free undamped/damped vibration, considered in the absence/presence of the inerter in the mechanical system. Influence of inertance on the amplitude of vibration, phase angle, natural frequency, damping ratio, and logarithmic decrement was clarified. It was mainly found that the inerter decreases the natural frequency of the undamped system and also of the damped system if the damping ratio is below 0.707. On the other hand, the inerter increases the natural frequency of the damped system if the damping ratio exceeds 0.707. Results obtained in this work are useful for the adequate design of inerters.
Abstract: In this paper, an advanced Nonlinear Exponential
Model (NEM), able to simulate the uniaxial dynamic behavior of
seismic isolators having a continuously decreasing tangent stiffness
with increasing displacement in the relatively large displacements
range and a hardening or softening behavior at large displacements, is
presented. The mathematical model is validated by comparing the
experimental force-displacement hysteresis loops obtained during
cyclic tests, conducted on a helical wire rope isolator and a recycled
rubber-fiber reinforced bearing, with those predicted analytically.
Good agreement between the experimental and simulated results
shows that the proposed model can be an effective numerical tool to
predict the force-displacement relationship of seismic isolation
devices within the large displacements range. Compared to the
widely used Bouc-Wen model, unable to simulate the response of
seismic isolators at large displacements, the proposed one allows to
avoid the numerical solution of a first order nonlinear ordinary
differential equation for each time step of a nonlinear time history
analysis, thus reducing the computation effort. Furthermore, the
proposed model can simulate the smooth transition of the hysteresis
loops from small to large displacements by adopting only one set of
five parameters determined from the experimental hysteresis loops
having the largest amplitude.
Abstract: In this paper, the results of experimental tests
performed on a Helical Wire Rope Isolator (HWRI) are presented in
order to describe the dynamic and static behavior of the selected
metal device in three different displacements ranges, namely small,
relatively large, and large displacements ranges, without and under
the effect of a vertical load. A testing machine, allowing to apply
horizontal displacement or load histories to the tested bearing with a
constant vertical load, has been adopted to perform the dynamic and
static tests. According to the experimental results, the dynamic
behavior of the tested device depends on the applied displacement
amplitude. Indeed, the HWRI displays a softening and a hardening
stiffness at small and relatively large displacements, respectively, and
a stronger nonlinear stiffening behavior at large displacements.
Furthermore, the experimental tests reveal that the application of a
vertical load allows to have a more flexible device with higher
damping properties and that the applied vertical load affects much
less the dynamic response of the metal device at large displacements.
Finally, a decrease in the static to dynamic effective stiffness ratio
with increasing displacement amplitude has been observed.
Abstract: New sensors and technologies – such as microphones,
touchscreens or infrared sensors – are currently making their
appearance in the automotive sector, introducing new kinds of
Human-Machine Interfaces (HMIs). The interactions with such tools
might be cognitively expensive, thus unsuitable for driving tasks.
It could for instance be dangerous to use touchscreens with a
visual feedback while driving, as it distracts the driver’s visual
attention away from the road. Furthermore, new technologies in
car cockpits modify the interactions of the users with the central
system. In particular, touchscreens are preferred to arrays of buttons
for space improvement and design purposes. However, the buttons’
tactile feedback is no more available to the driver, which makes
such interfaces more difficult to manipulate while driving. Gestures
combined with an auditory feedback might therefore constitute an
interesting alternative to interact with the HMI. Indeed, gestures can
be performed without vision, which means that the driver’s visual
attention can be totally dedicated to the driving task. In fact, the
auditory feedback can both inform the driver with respect to the task
performed on the interface and on the performed gesture, which might
constitute a possible solution to the lack of tactile information. As
audition is a relatively unused sense in automotive contexts, gesture
sonification can contribute to reducing the cognitive load thanks
to the proposed multisensory exploitation. Our approach consists
in using a virtual object (VO) to sonify the consequences of the
gesture rather than the gesture itself. This approach is motivated
by an ecological point of view: Gestures do not make sound, but
their consequences do. In this experiment, the aim was to identify
efficient sound strategies, to transmit dynamic information of VOs to
users through sound. The swipe gesture was chosen for this purpose,
as it is commonly used in current and new interfaces. We chose
two VO parameters to sonify, the hand-VO distance and the VO
velocity. Two kinds of sound parameters can be chosen to sonify the
VO behavior: Spectral or temporal parameters. Pitch and brightness
were tested as spectral parameters, and amplitude modulation as a
temporal parameter. Performances showed a positive effect of sound
compared to a no-sound situation, revealing the usefulness of sounds
to accomplish the task.