Abstract: A two-step multigrid approach is proposed to solve the inverse heat conduction problem in a 3-D object under laser irradiation. In the first step, the location of the laser center is estimated using a coarse and uniform grid system. In the second step, the front-surface temperature is recovered in good accuracy using a multiple grid system in which fine mesh is used at laser spot center to capture the drastic temperature rise in this region but coarse mesh is employed in the peripheral region to reduce the total number of sensors required. The effectiveness of the two-step approach and the multiple grid system are demonstrated by the illustrative inverse solutions. If the measurement data for the temperature and heat flux on the back surface do not contain random error, the proposed multigrid approach can yield more accurate inverse solutions. When the back-surface measurement data contain random noise, accurate inverse solutions cannot be obtained if both temperature and heat flux are measured on the back surface.
Abstract: In this article, we present a layout printing way for producing Fresnel zone on 1294-1b doped liquid crystal with Methyl-Red azo dye. We made a Fresnel zone mask with 25 zones and radius of 5 mm using lithography technique. With layout printing way, we recorded mask’s pattern on cell with λ=532 nm solid-state diode pump laser. By recording Fresnel zone pattern on cell and making Fresnel pattern on the surface of cell, odd and even zones, will form. The printed pattern, because of Azo dye’s photoisomerization, was permanent. Experimentally, we saw focal length tunability from 32 cm to 43 cm.
Abstract: We report the enhancement of Raman scattering
signal by one order of magnitude using photonic nanojet (PNJ) of a
lollipop shaped dielectric microstructure (LSDM) fabricated by a
pulsed CO₂ laser. Here, the PNJ is generated by illuminating sphere
portion of the LSDM with non-resonant laser. Unlike the surface
enhanced Raman scattering (SERS) technique, this technique is
simple, and the obtained results are highly reproducible. In addition,
an efficient technique is proposed to enhance the SERS signal with
the help of high quality factor optical resonance (whispering gallery
mode) of a LSDM. From the theoretical simulations, it has been
found that at least an order of magnitude enhancement in the SERS
signal could be achieved easily using the proposed technique. We
strongly believe that this report will enable the research community
for improving the Raman scattering signals.
Abstract: The quality of laser welded-brazed (LWB) joints were strongly dependent on the main process parameters, therefore the effect of laser power (3.2–4 kW), welding speed (60–80 mm/s) and wire feed rate (70–90 mm/s) on mechanical strength and surface roughness were investigated in this study. The comprehensive optimization process by means of response surface methodology (RSM) and desirability function was used for multi-criteria optimization. The experiments were planned based on Box– Behnken design implementing linear and quadratic polynomial equations for predicting the desired output properties. Finally, validation experiments were conducted on an optimized process condition which exhibited good agreement between the predicted and experimental results. AlSi3Mn1 was selected as the filler material for joining aluminum alloy 6022 and hot-dip galvanized steel in coach peel configuration. The high scanning speed could control the thickness of IMC as thin as 5 µm. The thermal simulations of joining process were conducted by the Finite Element Method (FEM), and results were validated through experimental data. The Fe/Al interfacial thermal history evidenced that the duration of critical temperature range (700–900 °C) in this high scanning speed process was less than 1 s. This short interaction time leads to the formation of reaction-control IMC layer instead of diffusion-control mechanisms.
Abstract: To the author’s knowledge, despite the written documents about Marist spirituality/charism, nothing has been done concerning a clear theoretical framework that highlights Marist spirituality/charism from the perspective or lived experience of the lay Marists of St. Marcellin Champagnat. The participants of the study are the lay Marist - educators who are from Marist Schools in the Philippines. Since the study would like to find out the respondents’ own concepts and meanings about Marist spirituality/charism, qualitative methodology is considered the approach to be used in the study. In particular, the study will use the qualitative methods of Barney Glaser. The theory will be generated systematically from data collection, coding and analyzing through memoing, theoretical sampling, sorting and writing and using the constant comparative method. The data collection method that will be employed in this grounded theory research is the in-depth interview that is semi-structured and participant driven. Data collection will be done through snowball sampling that is purposive. The study is considering to come up with a theoretical framework that will help the lay Marists to deepen their understanding of the Marist spirituality/charism and their vocation as lay partners of the Marist Brothers of the Schools.
Abstract: Diffraction grating is periodic module used in many
engineering fields, its geometrical conception gives interesting
properties of diffraction and interferences, a uniform and periodic
diffraction grating consists of a number of identical apertures that are
equally spaced, in this case, the amplitude of intensity distribution
in the far field region is generally modulated by diffraction pattern
of single aperture. In this paper, we study the case of aperiodic
diffraction grating with identical rectangular apertures where theirs
coordinates are modeled by square root function, we elaborate a
computer simulation comparatively to the periodic array with same
length and we discuss the numerical results.
Abstract: In the present research work we present the optical
emission studies of the Indium (In) – Tin (Sn) plasma produced by
the first (1064 nm) harmonic of an Nd: YAG nanosecond pulsed
laser. The experimentally observed line profiles of neutral Indium (In
I) and Tin (SnI) are used to extract the electron temperature (Te)
using the Boltzmann plot method. Whereas, the electron number
density (Ne) has been determined from the Stark broadening line
profile method. The Te is calculated by varying the distance from the
target surface along the line of propagation of plasma plume and also
by varying the laser irradiance. Beside we have studied the variation
of Ne as a function of laser irradiance as well as its variation with
distance from the target surface.
Abstract: Zinc oxide (ZnO) is one of the light emitting materials in ultraviolet (UV) region. In addition, ZnO nanostructures are also attracting increasing research interest as buildingblocks for UV optoelectronic applications. We have succeeded in synthesizing vertically-aligned ZnO nanostructures by laser interference patterning, which is catalyst-free and non-contact technique. In this study, vertically-aligned ZnO nanowall arrays were synthesized using two-beam interference. The maximum height and average thickness of the ZnO nanowalls were about 4.5µm and 200 nm, respectively.UV lasing from a piece of the ZnO nanowall was obtained under the third harmonic of a Q-switched Nd:YAG laser excitation, and the estimated threshold power density for lasing was about 150 kW/cm2. Furthermore, UV lasing from the vertically-aligned ZnO nanowall was also achieved. The results indicate that ZnO nanowalls can be applied to random laser.
Abstract: We report on the use of strong external optical
feedback to enhance the modulation response of semiconductor lasers
over a frequency passband around modulation frequencies higher
than 60 GHz. We show that this modulation enhancement is a type of
photon-photon resonance (PPR) of oscillating modes in the external
cavity formed between the laser and the external reflector. The study
is based on a time-delay rate equation model that takes into account
both the strong feedback and multiple reflections in the external
cavity. We examine the harmonic and intermodulation distortions
associated with single and two-tone modulations in the mm-wave
band of the resonant modulation. We show that compared with
solitary lasers modulated around the carrier-photon resonance
frequency, the present mm-wave modulated signal has lower
distortions.
Abstract: We model and simulate the combined effect of fiber
dispersion and frequency chirp of a directly modulated high-speed
laser diode on the figures of merit of a non-amplified 40-Gbps optical
fiber link. We consider both the return to zero (RZ) and non-return to
zero (NRZ) patterns of the pseudorandom modulation bits. The
performance of the fiber communication system is assessed by the
fiber-length limitation due to the fiber dispersion. We study the
influence of replacing standard single-mode fibers by non-zero
dispersion-shifted fibers on the maximum fiber length and evaluate
the associated power penalty. We introduce new dispersion
tolerances for 1-dB power penalty of the RZ and NRZ 40-Gbps
optical fiber links.
Abstract: This paper describes Nano-particle based Planar Laser
Scattering (NPLS) flow visualization of angled supersonic jets into a
supersonic cross flow based on the HYpersonic Low TEmperature
(HYLTE) nozzle which was widely used in DF chemical laser. In
order to investigate the non-reacting flowfield in the HYLTE nozzle, a
testing section with windows was designed and manufactured. The
impact of secondary fluids orifice separation on mixing was examined.
For narrow separation of orifices, the secondary fuel penetration
increased obviously compared to diluent injection, which means
smaller separation of diluent and fuel orifices would enhance the
mixing of fuel and oxidant. Secondary injections with angles of 30, 40
and 50 degrees were studied. It was found that the injectant
penetration increased as the injection angle increased, while the
interfacial surface area to entrain the freestream fluid is largest when
the injection angle is 40 degree.
Abstract: In this paper, a fibre laser at 546 nm has been studied
for a signal power of -30 dB. Er3+-doped ZBLAN fibre has been used
by upconversion pumping of a 980 nm laser diode. Gain saturation
effect has been investigated in detail. Laser performance has also been
discussed. An efficiency of 35% has been calculated with a length of 5
mm fibre laser. Results show that Er3+-doped ZBLAN is a promising
candidate for optical amplification at 546 nm.
Abstract: In the present investigation, H13 tool steel has been
deposited on copper alloy substrate using both CO2 and diode laser.
A detailed parametric analysis has been carried out in order to find
out optimum processing zone for coating defect free H13 tool steel
on copper alloy substrate. Followed by parametric optimization, the
microstructure and microhardness of the deposited clads have been
evaluated. SEM micrographs revealed dendritic microstructure in
both clads. However, the microhardness of CO2 laser deposited clad
was much higher compared to diode laser deposited clad.
Abstract: Encoded information based on synchronization of coupled chaotic Nd:YAG lasers in master-slave configuration is numerically studied. Encoding, transmission, and decoding of information in optical chaotic communication with a single channel is presented. We analyze the robustness of the encrypted audio transmission in a channel noise. In order to illustrate this synchronization robustness, we present two cases of study: synchronization and transmission with a single channel without and with noise in the channel.
Abstract: This paper adopted the hybrid differential transform approach for studying heat transfer problems in a gold/chromium thin film with an ultra-short-pulsed laser beam projecting on the gold side. The physical system, formulated based on the hyperbolic two-step heat transfer model, covers three characteristics: (i) coupling effects between the electron/lattice systems, (ii) thermal wave propagation in metals, and (iii) radiation effects along the interface. The differential transform method is used to transfer the governing equations in the time domain into the spectrum equations, which is further discretized in the space domain by the finite difference method. The results, obtained through a recursive process, show that the electron temperature in the gold film can rise up to several thousand degrees before its electron/lattice systems reach equilibrium at only several hundred degrees. The electron and lattice temperatures in the chromium film are much lower than those in the gold film.
Abstract: Nowadays, quasi-continuous wave diode lasers are
used in a widespread variety of applications. Temperature effects in
these lasers can strongly influence their performance. In this paper,
the effects of temperature have been experimentally investigated on
different features of a 60W-QCW diode laser. The obtained results
indicate that the conversion efficiency and operation voltage of diode
laser decrease with the augmentation of the working temperature
associated with a redshift in the laser peak wavelength. Experimental
results show the emission peak wavelength of laser shifts 0.26 nm
and the conversion efficiency decreases 1.76 % with the increase of
temperature from 40 to 50 ̊C. Present study also shows the slope
efficiency decreases gradually at low temperatures and rapidly at
higher temperatures. Regarding the close dependence of the
mentioned parameters to the operating temperature, it is of great
importance to carefully control the working temperature of diode
laser, particularly for medical applications.
Abstract: We present the development of a new underwater laser
cutting process in which a water-jet has been used along with the
laser beam to remove the molten material through kerf. The
conventional underwater laser cutting usually utilizes a high pressure
gas jet along with laser beam to create a dry condition in the cutting
zone and also to eject out the molten material. This causes a lot of gas
bubbles and turbulence in water, and produces aerosols and waste
gas. This may cause contamination in the surrounding atmosphere
while cutting radioactive components like burnt nuclear fuel. The
water-jet assisted underwater laser cutting process produces much
less turbulence and aerosols in the atmosphere. Some amount of
water vapor bubbles is formed at the laser-metal-water interface;
however, they tend to condense as they rise up through the
surrounding water. We present the design and development of a
water-jet assisted underwater laser cutting head and the parametric
study of the cutting of AISI 304 stainless steel sheets with a 2 kW
CW fiber laser. The cutting performance is similar to that of the gas
assist laser cutting; however, the process efficiency is reduced due to
heat convection by water-jet and laser beam scattering by vapor. This
process may be attractive for underwater cutting of nuclear reactor
components.