Abstract: Thirty six samples from each (aerobic and anoxic)
activated sludge were collected from two wastewater treatment plants
with MBRs in Berlin, Germany. The samples were prepared for count
and definition of fungal isolates; these isolates were purified by
conventional techniques and identified by microscopic examination.
Sixty tow species belonging to 28 genera were isolated from
activated sludge samples under aerobic conditions (28 genera and 58
species) and anoxic conditions (26 genera and 52 species). The
obtained data show that, Aspergillus was found at 94.4% followed by
Penicillium 61.1 %, Fusarium (61.1 %), Trichoderma (44.4 %) and
Geotrichum candidum (41.6 %) species were the most prevalent in all
activated sludge samples. The study confirmed that fungi can thrive
in activated sludge and sporulation, but isolated in different numbers
depending on the effect of aeration system. Some fungal species in
our study are saprophytic, and other a pathogenic to plants and
animals.
Abstract: This paper describes technological possibilities to
enhance methane productionin the anaerobic stabilization of wastewater treatment plant excess sludge. This objective can be achieved by the addition of waste residues: crude glycerol from biodiesel production and residues from fishery. The addition
ofglycerol in an amount by weight of 2 – 5% causes enhancement of methane production of about 250 – 400%. At the same time the
percentage increase of total solids concentration in the outgoing sludge is ten or more times less. The containment of methane in
biogas is higher in case of admixed substrate.
Abstract: The abundance and availability of rice husk, an agricultural waste, make them as a good source for precursor of activated carbon. In this work, rice husk-based activated carbons were prepared via base treated chemical activation process prior the carbonization process. The effect of carbonization temperatures (400, 600 and 800oC) on their pore structure was evaluated through morphology analysis using scanning electron microscope (SEM). Sample carbonized at 800oC showed better evolution and development of pores as compared to those carbonized at 400 and 600oC. The potential of rice husk-based activated carbon as an alternative adsorbent was investigated for the removal of Ni(II), Zn(II) and Pb(II) from single metal aqueous solution. The adsorption studies using rice husk-based activated carbon as an adsorbent were carried out as a function of contact time at room temperature and the metal ions were analyzed using atomic absorption spectrophotometer (AAS). The ability to remove metal ion from single metal aqueous solution was found to be improved with the increasing of carbonization temperature. Among the three metal ions tested, Pb(II) ion gave the highest adsorption on rice husk-based activated carbon. The results obtained indicate the potential to utilize rice husk as a promising precursor for the preparation of activated carbon for removal of heavy metals.
Abstract: Excilamps are new UV sources with great potential
for application in wastewater treatment. In the present work, a XeBr
excilamp emitting radiation at 283 nm has been used for the
photodegradation of 4-chlorophenol within a range of concentrations
from 50 to 500 mg L-1. Total removal of 4-chlorophenol was
achieved for all concentrations assayed. The two main photoproduct
intermediates formed along the photodegradation process,
benzoquinone and hydroquinone, although not being completely
removed, remain at very low residual concentrations. Such
concentrations are insignificant compared to the 4-chlorophenol
initial ones and non-toxic. In order to simulate the process and scaleup,
a kinetic model has been developed and validated from the
experimental data.
Abstract: The purpose of this research was develop a biological
nutrient removal (BNR) system which has low energy consumption, sludge production, and land usage. These indicate that BNR system could be a alternative of future wastewater treatment in ubiquitous
city(U-city). Organics and nitrogen compounds could be removed by this system so that secondary or tertiary stages of wastewater treatment satisfy their standards. This system was composed of oxic and anoxic
filter filed with PVDC and POM media. Anoxic/oxic filter system operated under empty bed contact time of 4 hours by increasing
recirculation ratio from 0 to 100 %. The system removals of total nitrogen and COD were 76.3% and 93%, respectively. To be observed
internal behavior in this system SCOD, NH3-N, and NO3-N were
conducted and removal shows range of 25~100%, 59~99%, and
70~100%, respectively.
Abstract: The Beshar River is one aquatic ecosystem, which is
located next to the city of Yasuj in southern Iran. The Beshar river
has been contaminated by industrial factories such as effluent of
sugar factory, agricultural and other activities in this region such as,
Imam Sajjad hospital, drainage from agricultural farms, Yasuj urban
surface runoff and effluent of wastewater treatment plants ,specially
Yasuj waste water treatment plant. In order to evaluate the effects of
these pollutants on the quality of the Beshar river, five monitoring
stations were selected along its course. The first station is located
upstream of Yasuj near the Dehnow village; stations 2 to 4 are
located east, south and west of city; and the 5th station is located
downstream of Yasuj. Several water quality parameters were
sampled. These include pH, dissolved oxygen, biological oxygen
demand (BOD), temperature, conductivity, turbidity, total dissolved
solids and discharge or flow measurements. Water samples from the
five stations were collected and analyzed to determine the following
physicochemical parameters: EC, pH, T.D.S, T.H, No2, DO, BOD5,
COD during 2008 to 2010. The study shows that the BOD5 value of
station 1 is at a minimum (1.7 ppm) and increases downstream from
stations 2 to 4 to a maximum (11.6 ppm), and then decreases at
station 5. The DO values of station 1 is a maximum (8.45 ppm),
decreases downstream to stations 2 - 4 which are at a minimum (3.1
ppm), before increasing at station 5. The amount of BOD and TDS
are highest at the 4th station and the amount of DO is lowest at this
station, marking the 4th station as more highly polluted than the
other stations .This study shows average amount of the water quality
parameters in first year of sampling (2008) have had a better quality
relation to third year in 2010 because of recent drought in this region
and pollutant increasing .As the Beshar river path after 5th station
goes through the mountain area with more slope and flow velocity
,so the physicochemical parameters improve at the 5th station due to
pollutant degradation and dilution. Finally the point and nonpoint
pollutant sources of Beshar river were determined and compared to
the monitoring results.
Abstract: “Garbage enzyme", a fermentation product of kitchen waste, water and brown sugar, is claimed in the media as a multipurpose solution for household and agricultural uses. This study assesses the effects of dilutions (5% to 75%) of garbage enzyme in reducing pollutants in domestic wastewater. The pH of the garbage enzyme was found to be 3.5, BOD concentration about 150 mg/L. Test results showed that the garbage enzyme raised the wastewater-s BOD in proportion to its dilution due to its high organic content. For mixtures with more than 10% garbage enzyme, its pH remained acidic after the 5-day digestion period. However, it seems that ammonia nitrogen and phosphorus could be removed by the addition of the garbage enzyme. The most economic solution for removal of ammonia nitrogen and phosphorus was found to be 9%. Further tests are required to understand the removal mechanisms of the ammonia nitrogen and phosphorus.
Abstract: The growth of the aquaculture industry has been
associated with negative environmental impacts through the
discharge of raw effluents into the adjacent receiving water bodies.
Macrophytes from natural saline lakes, which have adaptability to the
high salinity, can be suitable for saline effluent treatment. Eight
emergent species from natural saline area were planted in an
experimental gravel bed hydroponic mesocosm (GBH) which was
treated with effluent water from an intensive fish farm using
geothermal water. In order to examine the applicability of the
halophytes in treatment processes, we tested the relative efficacy of
total nitrogen (TN), total phosphorus (TP), potassium (K), sodium
(Na), magnesium (Mg) and calcium (Ca) removal for the saline
wastewater treatment. Four of the eight species, which were
Phragmites australis, Typha angustifolia, Glyceria maxima, Scirpus
lacustris spp. tabernaemontani could survive and contribute the
experimental treatment.
Abstract: From environmental aspect purification of ammonia
containing wastewater is expected. High efficiency ammonia
desorption can be done from the water by air on proper temperature.
After the desorption process, ammonia can be recovered and used in
another technology. The calculation method described below give
some methods to find either the minimum column height or ammonia
rich solution of the effluent.
Abstract: Residual dye contents in textile dyeing wastewater have complex aromatic structures that are resistant to degrade in biological wastewater treatment. The objectives of this study were to determine the effectiveness of nanoscale zerovalent iron (NZVI) to decolorize Reactive Black 5 (RB5) and Reactive Red 198 (RR198) in synthesized wastewater and to investigate the effects of the iron particle size, iron dosage and solution pHs on the destruction of RB5 and RR198. Synthesized NZVI was confirmed by transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The removal kinetic rates (kobs) of RB5 (0.0109 min-1) and RR198 (0.0111 min-1) by 0.5% NZVI were many times higher than those of microscale zerovalent iron (ZVI) (0.0007 min-1 and 0.0008 min-1, respectively). The iron dosage increment exponentially increased the removal efficiencies of both RB5 and RR198. Additionally, lowering pH from 9 to 5 increased the decolorization kinetic rates of both RB5 and RR198 by NZVI. The destruction of azo bond (N=N) in the chromophore of both reactive dyes led to decolorization of dye solutions.
Abstract: The main objective of this study was to remove and recover Ni, Cu and Fe from a mixed metal system using sodium hypophosphite as a reducing agent and nickel powder as seeding material. The metal systems studied consisted of Ni-Cu, Ni-Fe and Ni-Cu-Fe solutions. A 5 L batch reactor was used to conduct experiments where 100 mg/l of each respective metal was used. It was found that the metals were reduced to their elemental form with removal efficiencies of over 80%. The removal efficiency decreased in the order Fe>Ni>Cu. The metal powder obtained contained between 97-99% Ni and was almost spherical and porous. Size enlargement by aggregation was the dominant particulate process.
Abstract: In this paper, periodic force operation of a wastewater treatment process has been studied for the improved process performance. A previously developed dynamic model for the process is used to conduct the performance analysis. The static version of the model was utilized first to determine the optimal productivity conditions for the process. Then, feed flow rate in terms of dilution rate i.e. (D) is transformed into sinusoidal function. Nonlinear model predictive control algorithm is utilized to regulate the amplitude and period of the sinusoidal function. The parameters of the feed cyclic functions are determined which resulted in improved productivity than the optimal productivity under steady state conditions. The improvement in productivity is found to be marginal and is satisfactory in substrate conversion compared to that of the optimal condition and to the steady state condition, which corresponds to the average value of the periodic function. Successful results were also obtained in the presence of modeling errors and external disturbances.
Abstract: Zeolite A and MCM-41 have extensive applications in basic science, petrochemical science, energy conservation/storage, medicine, chemical sensor, air purification, environmentally benign composite structure and waste remediation. However, the use of zeolite A and MCM-41 in these areas, especially environmental remediation, are restricted due to prohibitive production cost. Efficient recycling of and resource recovery from coal fly ash has been a major topic of current international research interest, aimed at achieving sustainable development of human society from the viewpoints of energy, economy, and environmental strategy. This project reported an original, novel, green and fast methods to produce nano-porous zeolite A and MCM-41 materials from coal fly ash. For zeolite A, this novel production method allows a reduction by half of the total production time while maintaining a high degree of crystallinity of zeolite A which exists in a narrower particle size distribution. For MCM-41, this remarkably green approach, being an environmentally friendly process and reducing generation of toxic waste, can produce pure and long-range ordered MCM-41 materials from coal fly ash. This approach took 24 h at 25 oC to produce 9 g of MCM-41 materials from 30 g of the coal fly ash, which is the shortest time and lowest reaction temperature required to produce pure and ordered MCM-41 materials (having the largest internal surface area) compared to the values reported in the literature. Performance evaluation of the produced zeolite A and MCM-41 materials in wastewater treatment and air pollution control were reported. The residual fly ash was also converted to zeolite Na-P1 which showed good performance in removal of multi-metal ions in wastewater. In wastewater treatment, compared to commercial-grade zeolite A, adsorbents produced from coal fly ash were effective in removing multi heavy metal ions in water and could be an alternative material for treatment of wastewater. In methane emission abatement, the zeolite A (produced from coal fly ash) achieved similar methane removal efficiency compared to the zeolite A prepared from pure chemicals. This report provides the guidance for production of zeolite A and MCM-41 from coal fly ash by a cost-effective approach which opens potential applications of these materials in environmental industry. Finally, environmental and economic aspects of production of zeolite A and MCM-41 from coal fly ash were discussed.
Abstract: Intermittent aeration process can be easily applied on
the existing activated sludge system and is highly reliable against the loading changes. It can be operated in a relatively simple way as well.
Since the moving-bed biofilm reactor method processes pollutants by attaching and securing the microorganisms on the media, the process
efficiency can be higher compared to the suspended growth biological
treatment process, and can reduce the return of sludge. In this study,
the existing intermittent aeration process with alternating flow being
applied on the oxidation ditch is applied on the continuous flow stirred tank reactor with advantages from both processes, and we would like
to develop the process to significantly reduce the return of sludge in the clarifier and to secure the reliable quality of treated water by
adding the moving media. Corresponding process has the appropriate
form as an infrastructure based on u- environment in future u- City and
is expected to accelerate the implementation of u-Eco city in conjunction with city based services. The system being conducted in a
laboratory scale has been operated in HRT 8hours except for the final
clarifier and showed the removal efficiency of 97.7 %, 73.1 % and 9.4
% in organic matters, TN and TP, respectively with operating range of
4hour cycle on system SRT 10days. After adding the media, the removal efficiency of phosphorus showed a similar level compared to
that before the addition, but the removal efficiency of nitrogen was
improved by 7~10 %. In addition, the solids which were maintained in
MLSS 1200~1400 at 25 % of media packing were attached all onto the
media, which produced no sludge entering the clarifier. Therefore, the
return of sludge is not needed any longer.
Abstract: The remediation of water resources pollution in
developing countries requires the application of alternative
sustainable cheaper and efficient end-of-pipe wastewater treatment
technologies. The feasibility of use of South African cheap and
abundant pine tree (Pinus patula) sawdust for development of lowcost
AC of comparable quality to expensive commercial ACs in the
abatement of water pollution was investigated. AC was developed at
optimized two-stage N2-superheated steam activation conditions in a
fixed bed reactor, and characterized for proximate and ultimate
properties, N2-BET surface area, pore size distribution, SEM, pHPZC
and FTIR. The sawdust pyrolysis activation energy was evaluated by
TGA. Results indicated that the chars prepared at 800oC and 2hrs
were suitable for development of better quality AC at 800oC and 47%
burn-off having BET surface area (1086m2/g), micropore volume
(0.26cm3/g), and mesopore volume (0.43cm3/g) comparable to
expensive commercial ACs, and suitable for water contaminants
removal. The developed AC showed basic surface functionality at
pHPZC at 10.3, and a phenol adsorption capacity that was higher than
that of commercial Norit (RO 0.8) AC. Thus, it is feasible to develop
better quality low-cost AC from (Pinus patula) sawdust using twostage
N2-steam activation in fixed-bed reactor.
Abstract: The reduction of hexavalent chromium by scrap iron
was investigated in continuous system, using long-term column
experiments, for aqueous Cr(VI) solutions having low buffering
capacities, over the Cr(VI) concentration range of 5 – 40 mg/L. The
results showed that the initial Cr(VI) concentration significantly
affects the reduction capacity of scrap iron. Maximum reduction
capacity of scrap iron was observed at the beginning of the column
experiments; the lower the Cr(VI) concentration, the greater the
experiment duration with maximum scrap iron reduction capacity.
However, due to passivation of active surface, scrap iron reduction
capacity continuously decreased in time, especially after Cr(VI)
breakthrough. The experimental results showed that highest
reduction capacity recorded until Cr(VI) breakthrough was 22.8 mg
Cr(VI)/g scrap iron, at CI = 5 mg/L, and decreased with increasing
Cr(VI) concentration. In order to assure total reduction of greater
Cr(VI) concentrations for a longer period of time, either the mass of
scrap iron filling, or the hydraulic retention time should be increased.
Abstract: The research study is carried out to determine the efficiency of the Biofilm sewage treatment plant which is located at the Engineering Complex-s. Wastewater analyses have been carried out at the Environmental Engineering laboratory to study the six parameters: Biochemical Oxygen Demand BOD, Chemical Oxygen Demand COD l, and Total Suspended Solids TSS, Ammoniac Nitrogen NH3-N and Phosphorous P which have been selected to determine the wastewater quality. The plant was designed to treat 750 Pe (population equivalent) at hydraulic retention time of 5 hours in the aerobic zone. The results show that Biofilm wastewater treatment plant was able to treat sewage successfully at different flow condition. The discharge has fulfilled the Malaysia Environmental of Standard A water quality. The achieved BOD removal is more than 85%, COD is more than 80%, TSS is more than 80%, NH3-N is more than 70%, and P was more than 70%. The Biofilm system provides a very efficient process for sewage treatment and it is compact in structure thus minimizes the required land area.
Abstract: 17α-ethynylestradiol (EE2) is a synthetic estrogen
used as a key ingredient in an oral contraceptives pill. EE2 is an
endocrine disrupting compound, high in estrogenic potency.
Although EE2 exhibits low degree of biodegradability with common
microorganisms in wastewater treatment plants (WWTPs), this
compound can be biotransformed by ammonia-oxidizing bacteria
(AOB) via a co-metabolism mechanism in WWTPs. This study
aimed to investigate the effect of real wastewater on
biotransformation of EE2 by AOB. A preliminary experiment on the
effect of nitrite and pH levels on abiotic transformation of EE2
suggested that the abiotic transformation occurred at only pH
Abstract: An attempt was made for availability of wastewater reuse/reclamation for irrigation purposes using phytoremediation “the low cost and less technology", using six local aquatic macrophytes “e.g. T. angustifolia, B. maritimus, Ph. australis, A. donax, A. plantago-aquatica and M. longifolia (Linn)" as biological waste purifiers. Outdoor experiments/designs were conducted from May 03, 2007 till October 15, 2008, close to one of the main sewage channels of Sulaimani City/Iraq*. All processes were mainly based on conventional wastewater treatment processes, besides two further modifications were tested, the first was sand filtration pots, implanted by individual species of experimental macrophytes and the second was constructed wetlands implanted by experimental macrophytes all together. Untreated and treated wastewater samples were analyzed for their key physico-chemical properties (only heavy metals Fe, Mn, Zn and Cu with particular reference to removal efficiency by experimental macrophytes are highlighted in this paper). On the other hand, vertical contents of heavy metals were also evaluated from both pots and the cells of constructed wetland. After 135 days, macrophytes were harvested and heavy metals were analyzed in their biomass (roots/shoots) for removal efficiency assessment (i.e. uptake/ bioaccumulation rate). Results showed that; removal efficiency of all studied heavy metals was much higher in T. angustifolia followed by Ph. Australis, B. maritimus and A. donax in triple experiment sand pots. Constructed wetland experiments have revealed that; the more replicated constructed wetland cells the highest heavy metal removal efficiency was indicated.
Abstract: Water hyacinth has been used in aquatic systems for
wastewater purification in many years worldwide. The role of water
hyacinth (Eichhornia crassipes) species in polishing nitrate and
phosphorus concentration from municipal wastewater treatment plant
effluent by phytoremediation method was evaluated. The objective
of this project is to determine the removal efficiency of water
hyacinth in polishing nitrate and phosphorus, as well as chemical
oxygen demand (COD) and ammonia. Water hyacinth is considered
as the most efficient aquatic plant used in removing vast range of
pollutants such as organic matters, nutrients and heavy metals. Water
hyacinth, also referred as macrophytes, were cultivated in the
treatment house in a reactor tank of approximately 90(L) x 40(W) x
25(H) in dimension and built with three compartments. Three water
hyacinths were placed in each compartments and water sample in
each compartment were collected in every two days. The plant
observation was conducted by weight measurement, plant uptake and
new young shoot development. Water hyacinth effectively removed
approximately 49% of COD, 81% of ammonia, 67% of phosphorus
and 92% of nitrate. It also showed significant growth rate at starting
from day 6 with 0.33 shoot/day and they kept developing up to 0.38
shoot/day at the end of day 24. From the studies conducted, it was
proved that water hyacinth is capable of polishing the effluent of
municipal wastewater which contains undesirable amount of nitrate
and phosphorus concentration.