Abstract: In this paper, we have presented and analyzed three-dimensional (3-D) matrices of wavelength/time/space code for optical code division multiple access (OCDMA) networks with NAND subtraction detection technique. The 3-D codes are constructed by integrating a two-dimensional modified quadratic congruence (MQC) code with one-dimensional modified prime (MP) code. The respective encoders and decoders were designed using fiber Bragg gratings and optical delay lines to minimize the bit error rate (BER). The performance analysis of the 3D-OCDMA system is based on measurement of signal to noise ratio (SNR), BER and eye diagram for a different number of simultaneous users. Also, in the analysis, various types of noises and multiple access interference (MAI) effects were considered. The results obtained with NAND detection technique were compared with those obtained with OR and AND subtraction techniques. The comparison results proved that the NAND detection technique with 3-D MQC\MP code can accommodate more number of simultaneous users for longer distances of fiber with minimum BER as compared to OR and AND subtraction techniques. The received optical power is also measured at various levels of BER to analyze the effect of attenuation.
Abstract: Frequency estimation of a sinusoid in white noise using
maximum entropy power spectral estimation has been shown to be
very sensitive to initial sinusoidal phase. This paper presents use of
wavelet transform to find an analytic signal for frequency estimation
using maximum entropy method (MEM) and compared the results
with frequency estimation using analytic signal by Hilbert transform
method and frequency estimation using real data together with MEM.
The presented method shows the improved estimation precision and
antinoise performance.
Abstract: Grinding operation is performed in order to obtain desired surfaces precisely in machining process. The needed relative motion between the cutting tool and the workpiece is generally created either by the movement of the cutting tool or by the movement of the workpiece or by the movement of both of them as in our case. For all these cases, the coherence level between the movements and the interaction forces is a key influential parameter for efficient grinding. Therefore, in this work, spectral coherence analysis has been performed to investigate the coherence level between grinding interaction forces and the movement of the workpiece on our robotic-grinding experimental setup in METU Mechatronics Laboratory.
Abstract: In this study, it was aimed to determine a route for identification of rice cultivation areas within Thrace and Marmara regions of Turkey using remote sensing and GIS. Landsat 8 (OLI-TIRS) imageries acquired in production season of 2013 with 181/32 Path/Row number were used. Four different seasonal images were generated utilizing original bands and different transformation techniques. All images were classified individually using supervised classification techniques and Land Use Land Cover Maps (LULC) were generated with 8 classes. Areas (ha, %) of each classes were calculated. In addition, district-based rice distribution maps were developed and results of these maps were compared with Turkish Statistical Institute (TurkSTAT; TSI)’s actual rice cultivation area records. Accuracy assessments were conducted, and most accurate map was selected depending on accuracy assessment and coherency with TSI results. Additionally, rice areas on over 4° slope values were considered as mis-classified pixels and they eliminated using slope map and GIS tools. Finally, randomized rice zones were selected to obtain maximum-minimum value ranges of each date (May, June, July, August, September images separately) NDVI, LSWI, and LST images to test whether they may be used for rice area determination via raster calculator tool of ArcGIS. The most accurate classification for rice determination was obtained from seasonal LSWI LULC map, and considering TSI data and accuracy assessment results and mis-classified pixels were eliminated from this map. According to results, 83151.5 ha of rice areas exist within study area. However, this result is higher than TSI records with an area of 12702.3 ha. Use of maximum-minimum range of rice area NDVI, LSWI, and LST was tested in Meric district. It was seen that using the value ranges obtained from July imagery, gave the closest results to TSI records, and the difference was only 206.4 ha. This difference is normal due to relatively low resolution of images. Thus, employment of images with higher spectral, spatial, temporal and radiometric resolutions may provide more reliable results.
Abstract: Applicability of a KTA crystal-based laser system with optical parametric oscillators (OPO) generation to lidar sounding of the atmosphere in the spectral range 3–4 µm is studied in this work. A technique based on differential absorption lidar (DIAL) method and differential optical absorption spectroscopy (DOAS) is developed for lidar sounding of trace atmospheric gases (TAG). The DIAL-DOAS technique is tested to estimate its efficiency for lidar sounding of atmospheric trace gases.
Abstract: We present the concept and scientific methods and algorithms of our computation system called ATOMIC MATTERS. This is the first presentation of the new computer package, that allows its user to describe physical properties of atomic localized electron systems subject to electromagnetic interactions. Our solution applies to situations where an unclosed electron 2p/3p/3d/4d/5d/4f/5f subshell interacts with an electrostatic potential of definable symmetry and external magnetic field. Our methods are based on Crystal Electric Field (CEF) approach, which takes into consideration the electrostatic ligands field as well as the magnetic Zeeman effect. The application allowed us to predict macroscopic properties of materials such as: Magnetic, spectral and calorimetric as a result of physical properties of their fine electronic structure. We emphasize the importance of symmetry of charge surroundings of atom/ion, spin-orbit interactions (spin-orbit coupling) and the use of complex number matrices in the definition of the Hamiltonian. Calculation methods, algorithms and convention recalculation tools collected in ATOMIC MATTERS were chosen to permit the prediction of magnetic and spectral properties of materials in isostructural series.
Abstract: Regional variations in strong ground motions for the Iranian Plateau have been investigated by using a simple statistical method called Analysis of Variance (ANOVA). In this respect, a large database consisting of 1157 records occurring within the Iranian Plateau with moment magnitudes of greater than or equal to 5 and Joyner-Boore distances up to 200 km has been considered. Geometric averages of horizontal peak ground accelerations (PGA) as well as 5% damped linear elastic response spectral accelerations (SA) at periods of 0.2, 0.5, 1.0, and 2.0 sec are used as strong motion parameters. The initial database is divided into two different datasets, for Northern Iran (NI) and Central and Southern Iran (CSI). The comparison between strong ground motions of these two regions reveals that there is no evidence for significant differences; therefore, data from these two regions may be combined to estimate the unknown coefficients of attenuation relationships.
Abstract: Hyperspectral images and remote sensing are important for many applications. A problem in the use of these images is the high volume of data to be processed, stored and transferred. Dimensionality reduction techniques can be used to reduce the volume of data. In this paper, an approach to band selection based on clustering algorithms is presented. This approach allows to reduce the volume of data. The proposed structure is based on Fuzzy C-Means (or K-Means) and NWHFC algorithms. New attributes in relation to other studies in the literature, such as kurtosis and low correlation, are also considered. A comparison of the results of the approach using the Fuzzy C-Means and K-Means with different attributes is performed. The use of both algorithms show similar good results but, particularly when used attributes variance and kurtosis in the clustering process, however applicable in hyperspectral images.
Abstract: The next generation mobile communication systems i.e. fourth generation (4G) was developed to accommodate the quality of service and required data rate. This project focuses on multiple access technique proposed in 4G communication systems. It is attempted to demonstrate the IDMA (Interleave Division Multiple Access) technology. The basic principle of IDMA is that interleaver is different for each user whereas CDMA employs different signatures. IDMA inherits many advantages of CDMA such as robust against fading, easy cell planning; dynamic channel sharing and IDMA increase the spectral efficiency and reduce the receiver complexity. In this, performance of IDMA is analyzed using QC-LDPC coding scheme further it is compared with LDPC coding and at last BER is calculated and plotted in MATLAB.
Abstract: In this paper, a probabilistic framework based on
Fokker-Planck-Kolmogorov (FPK) approach has been applied to
simulate triaxial cyclic constitutive behavior of uncertain soils. The
framework builds upon previous work of the writers, and it has
been extended for cyclic probabilistic simulation of triaxial undrained
behavior of soils. von Mises elastic-perfectly plastic material model is
considered. It is shown that by using probabilistic framework, some of
the most important aspects of soil behavior under cyclic loading can
be captured even with a simple elastic-perfectly plastic constitutive
model.
Abstract: Performances analysis of remote sensing sensor is required to pursue a range of scientific research and application objectives. Laboratory analysis of any remote sensing instrument is essential, but not sufficient to establish a valid inflight one. In this study, with the aid of the in situ measurements and corresponding image of three-gray scale permanent artificial target, the in-flight radiometric performances analyses (in-flight radiometric calibration, dynamic range and response linearity, signal-noise-ratio (SNR), radiometric resolution) of self-developed short-wave infrared (SWIR) camera are performed. To acquire the inflight calibration coefficients of the SWIR camera, the at-sensor radiances (Li) for the artificial targets are firstly simulated with in situ measurements (atmosphere parameter and spectral reflectance of the target) and viewing geometries using MODTRAN model. With these radiances and the corresponding digital numbers (DN) in the image, a straight line with a formulation of L = G × DN + B is fitted by a minimization regression method, and the fitted coefficients, G and B, are inflight calibration coefficients. And then the high point (LH) and the low point (LL) of dynamic range can be described as LH= (G × DNH + B) and LL= B, respectively, where DNH is equal to 2n − 1 (n is the quantization number of the payload). Meanwhile, the sensor’s response linearity (δ) is described as the correlation coefficient of the regressed line. The results show that the calibration coefficients (G and B) are 0.0083 W·sr−1m−2µm−1 and −3.5 W·sr−1m−2µm−1; the low point of dynamic range is −3.5 W·sr−1m−2µm−1 and the high point is 30.5 W·sr−1m−2µm−1; the response linearity is approximately 99%. Furthermore, a SNR normalization method is used to assess the sensor’s SNR, and the normalized SNR is about 59.6 when the mean value of radiance is equal to 11.0 W·sr−1m−2µm−1; subsequently, the radiometric resolution is calculated about 0.1845 W•sr-1m-2μm-1. Moreover, in order to validate the result, a comparison of the measured radiance with a radiative-transfer-code-predicted over four portable artificial targets with reflectance of 20%, 30%, 40%, 50% respectively, is performed. It is noted that relative error for the calibration is within 6.6%.
Abstract: Compliant foil gas lubricated bearings are used for the
support of light loads in the order of few kilograms at high speeds, in
the order of 50,000 RPM. The stiffness of the foil bearings depends
both on the stiffness of the compliant foil and on the lubricating
gas film. The stiffness of the bearings plays a crucial role in the
stable operation of the supported rotor over a range of speeds. This
paper describes a numerical approach to estimate the stiffness of the
bearings using pseudo spectral scheme. Methodology to obtain the
stiffness of the foil bearing as a function of weight of the shaft is
given and the results are presented.
Abstract: This paper presents a SAC-OCDMA code with zero cross correlation property to minimize the Multiple Access Interface (MAI) as New Zero Cross Correlation code (NZCC), which is found to be more scalable compared to the other existing SAC-OCDMA codes. This NZCC code is constructed using address segment and data segment. In this work, the proposed NZCC code is implemented in an optical system using the Opti-System software for the spectral amplitude coded optical code-division multiple-access (SAC-OCDMA) scheme. The main contribution of the proposed NZCC code is the zero cross correlation, which reduces both the MAI and PIIN noises. The proposed NZCC code reveals properties of minimum cross-correlation, flexibility in selecting the code parameters and supports a large number of users, combined with high data rate and longer fiber length. Simulation results reveal that the optical code division multiple access system based on the proposed NZCC code accommodates maximum number of simultaneous users with higher data rate transmission, lower Bit Error Rates (BER) and longer travelling distance without any signal quality degradation, as compared to the former existing SAC-OCDMA codes.
Abstract: Mineral mapping on the Moon surface provides the clue to understand the origin, evolution, stratigraphy and geological history of the Moon. Recently, reflectance imaging spectroscopy plays a significant role in identifying minerals on the planetary surface in the Visible to NIR region of the electromagnetic spectrum. The Moon Mineralogy Mapper (M3) onboard Chandrayaan-1 provides unprecedented spectral data of lunar surface to study about the Moon surface. Here we used the M3 sensor data (hyperspectral imaging spectroscopy) for analysing mineralogy of Orientale basin region on the Moon surface. Reflectance spectrums were sampled from different locations of the basin and continuum was removed using ENvironment for Visualizing Images (ENVI) software. Reflectance spectra of unknown mineral composition were compared with known Reflectance Experiment Laboratory (RELAB) spectra for discriminating mineralogy. Minerals like olivine, Low-Ca Pyroxene (LCP), High-Ca Pyroxene (HCP) and plagioclase were identified. In addition to these minerals, an unusual type of spectral signature was identified, which indicates the probable Fe-Mg-spinel lithology in the basin region.
Abstract: Wireless Body Area Network (WBAN) is a short-range
wireless communication around human body for various applications
such as wearable devices, entertainment, military, and especially
medical devices. WBAN attracts the attention of continuous health
monitoring system including diagnostic procedure, early detection of
abnormal conditions, and prevention of emergency situations.
Compared to cellular network, WBAN system is more difficult to
control inter- and inner-cell interference due to the limited power,
limited calculation capability, mobility of patient, and
non-cooperation among WBANs.
In this paper, we compare the performance of resource allocation
scheme based on several Pseudo Orthogonal Codewords (POCs) to
mitigate inter-WBAN interference. Previously, the POCs are widely
exploited for a protocol sequence and optical orthogonal code. Each
POCs have different properties of auto- and cross-correlation and
spectral efficiency according to its construction of POCs. To identify
different WBANs, several different pseudo orthogonal patterns based
on POCs exploits for resource allocation of WBANs. By simulating
these pseudo orthogonal resource allocations of WBANs on
MATLAB, we obtain the performance of WBANs according to
different POCs and can analyze and evaluate the suitability of POCs
for the resource allocation in the WBANs system.
Abstract: Nowadays, food safety is a great public concern;
therefore, robust and effective techniques are required for detecting
the safety situation of goods. Hyperspectral Imaging (HSI) is an
attractive material for researchers to inspect food quality and safety
estimation such as meat quality assessment, automated poultry
carcass inspection, quality evaluation of fish, bruise detection of
apples, quality analysis and grading of citrus fruits, bruise detection
of strawberry, visualization of sugar distribution of melons,
measuring ripening of tomatoes, defect detection of pickling
cucumber, and classification of wheat kernels. HSI can be used to
concurrently collect large amounts of spatial and spectral data on the
objects being observed. This technique yields with exceptional
detection skills, which otherwise cannot be achieved with either
imaging or spectroscopy alone. This paper presents a nonlinear
technique based on kernel Fukunaga-Koontz transform (KFKT) for
detection of fat content in ground meat using HSI. The KFKT which
is the nonlinear version of FKT is one of the most effective
techniques for solving problems involving two-pattern nature. The
conventional FKT method has been improved with kernel machines
for increasing the nonlinear discrimination ability and capturing
higher order of statistics of data. The proposed approach in this paper
aims to segment the fat content of the ground meat by regarding the
fat as target class which is tried to be separated from the remaining
classes (as clutter). We have applied the KFKT on visible and nearinfrared
(VNIR) hyperspectral images of ground meat to determine
fat percentage. The experimental studies indicate that the proposed
technique produces high detection performance for fat ratio in ground
meat.
Abstract: Orthogonal Frequency Division Multiplexing
(OFDM) has been used in many advanced wireless communication
systems due to its high spectral efficiency and robustness to
frequency selective fading channels. However, the major concern
with OFDM system is the high peak-to-average power ratio (PAPR)
of the transmitted signal. Some of the popular techniques used for
PAPR reduction in OFDM system are conventional partial transmit
sequences (CPTS) and clipping. In this paper, a parallel
combination/hybrid scheme of PAPR reduction using clipping and
CPTS algorithms is proposed. The proposed method intelligently
applies both the algorithms in order to reduce both PAPR as well as
computational complexity. The proposed scheme slightly degrades
bit error rate (BER) performance due to clipping operation and it can
be reduced by selecting an appropriate value of the clipping ratio
(CR). The simulation results show that the proposed algorithm
achieves significant PAPR reduction with much reduced
computational complexity.
Abstract: Advances in spatial and spectral resolution of satellite
images have led to tremendous growth in large image databases. The
data we acquire through satellites, radars, and sensors consists of
important geographical information that can be used for remote
sensing applications such as region planning, disaster management.
Spatial data classification and object recognition are important tasks
for many applications. However, classifying objects and identifying
them manually from images is a difficult task. Object recognition is
often considered as a classification problem, this task can be
performed using machine-learning techniques. Despite of many
machine-learning algorithms, the classification is done using
supervised classifiers such as Support Vector Machines (SVM) as the
area of interest is known. We proposed a classification method,
which considers neighboring pixels in a region for feature extraction
and it evaluates classifications precisely according to neighboring
classes for semantic interpretation of region of interest (ROI). A
dataset has been created for training and testing purpose; we
generated the attributes by considering pixel intensity values and
mean values of reflectance. We demonstrated the benefits of using
knowledge discovery and data-mining techniques, which can be on
image data for accurate information extraction and classification from
high spatial resolution remote sensing imagery.
Abstract: In this paper, the experimental study for the instability
of a separator rotor is presented, under dynamic loading response in
the harmonic analysis condition. The global measurement and
analysis of vibration on the cement separator RC500 is carried, the
points of measurement used are radial dots, vertical, horizontal and
oblique. The measures of trends and spectral analysis for
reconnaissance of the main anomalies, the main defects in the
separator and manifestation, the results prove that the defects effect
has a negative effect on the stability of the rotor. Experimentally the
study of the rotor in transient system allowed to determine the
vibratory responses due to the unbalances and various excitations.
Abstract: The 1:1 cocrystal of 2-amino-4-chloro-6-
methylpyrimidine (2A4C6MP) with 4-methylbenzoic acid (4MBA)
(I) has been prepared by slow evaporation method in methanol,
which was crystallized in monoclinic C2/c space group, Z = 8, and a
= 28.431 (2) Å, b = 7.3098 (5) Å, c = 14.2622 (10) Å and β =
109.618 (3)°. The presence of unionized –COOH functional group in
cocrystal I was identified both by spectral methods (1H and 13C
NMR, FTIR) and X-ray diffraction structural analysis. The
2A4C6MP molecule interact with the carboxylic group of the
respective 4MBA molecule through N—H⋯O and O—H⋯N
hydrogen bonds, forming a cyclic hydrogen–bonded motif R2
2(8).
The crystal structure was stabilized by Npyrimidine—H⋯O=C and
C=O—H⋯Npyrimidine types hydrogen bonding interactions.
Theoretical investigations have been computed by HF and density
function (B3LYP) method with 6–311+G (d,p)basis set. The
vibrational frequencies together with 1H and 13C NMR chemical
shifts have been calculated on the fully optimized geometry of
cocrystal I. Theoretical calculations are in good agreement with the
experimental results. Solvent–free formation of this cocrystal I is
confirmed by powder X-ray diffraction analysis.