Abstract: Rendering light shafts is one of the important topics in computer gaming and interactive applications. The methods and models that are used to generate light shafts play crucial role to make a scene more realistic in computer graphics. This article discusses the image-based shadows and geometric-based shadows that contribute in generating volumetric shadows and light shafts, depending on ray tracing, radiosity, and ray marching technique. The main aim of this study is to provide researchers with background on a progress of light scattering methods so as to make it available for them to determine the technique best suited to their goals. It is also hoped that our classification helps researchers find solutions to the shortcomings of each method.
Abstract: Clustering phenomenon of pellets was observed frequently in shaft processes operating at higher temperatures. Clustering is a result of the growth of fibrous iron precipitates (iron whiskers) that become hooked to each other and finally become crystallized during the initial stages of metallization. If the pellet clustering is pronounced, sometimes leads to blocking inside the furnace and forced shutdown takes place. This work clarifies further the relation between metallic iron whisker growth and iron ore mineralogy. Various pellet sizes (6 – 12.0 & +12.0 mm) from three different ores (A, B & C) were (completely and partially) reduced at 985 oC with H2/CO gas mixture using thermos-gravimetric technique. It was found that reducibility increases by decreasing the iron ore pellet’s size. Ore (A) has the highest reducibility than ore (B) and ore (C). Increasing the iron ore pellet’s size leads to increase the probability of metallic iron whisker formation. Ore (A) has the highest tendency for metallic iron whisker formation than ore (B) and ore (C). The reduction reactions for all iron ores A, B and C are mainly controlled by diffusion reaction mechanism.
Abstract: The large karstic Bell spring with a discharge ranging between 250 and 5300 lit/ sec is one of the most important springs of Kermanshah Province. This spring supplies drinking water of Nodsheh City and its surrounding villages. The spring is located in the reservoir of Daryan Dam and its mouth would be submerged after impounding under a water column of about 110 m height. This paper has aimed to render an account of the karstification pattern around the spring under consideration with the intention of preventing Bell Spring from being submerged in Daryan Dam Reservoir. The studies comprise engineering geology and hydrogeology investigations. Some geotechnical activities included in these studies include geophysical studies, drilling, excavation of exploratory gallery and shaft and diving. The results depict that Bell is a single-conduit siphon spring with 4 m diameter and 85 m height that 32 m of the conduit is located below the spring outlet. To survive the spring, it was decided to plug the outlet and convey the water to upper elevations under the natural pressure of the aquifer. After plugging, water was successfully conveyed to elevation 837 meter above sea level (about 120 m from the outlet) under the natural pressure of the aquifer. This signifies the accuracy of the studies done and proper recognition of the karstification pattern of Bell Spring. This is a unique experience in karst problems in Iran.
Abstract: Compliant foil gas lubricated bearings are used for the
support of light loads in the order of few kilograms at high speeds, in
the order of 50,000 RPM. The stiffness of the foil bearings depends
both on the stiffness of the compliant foil and on the lubricating
gas film. The stiffness of the bearings plays a crucial role in the
stable operation of the supported rotor over a range of speeds. This
paper describes a numerical approach to estimate the stiffness of the
bearings using pseudo spectral scheme. Methodology to obtain the
stiffness of the foil bearing as a function of weight of the shaft is
given and the results are presented.
Abstract: To ensure the gas transmittal GCU's efficient operation, leakages through the labyrinth packings (LP) should be minimized. Leakages can be minimized by decreasing the LP gap, which in turn depends on thermal processes and possible rotor vibrations and is designed to ensure absence of mechanical contact. Vibration mitigation allows to minimize the LP gap. It is advantageous to research influence of processes in the dynamic gas-structure system on LP vibrations. This paper considers influence of rotor vibrations on LP gas dynamics and influence of the latter on the rotor structure within the FSI unidirectional dynamical coupled problem. Dependences of nonstationary parameters of gas-dynamic process in LP on rotor vibrations under various gas speeds and pressures, shaft rotation speeds and vibration amplitudes, and working medium features were studied. The programmed multi-processor ANSYS CFX was chosen as a numerical computation tool. The problem was solved using PNRPU high-capacity computer complex. Deformed shaft vibrations are replaced with an unyielding profile that moves in the fixed annulus "up-and-down" according to set harmonic rule. This solves a nonstationary gas-dynamic problem and determines time dependence of total gas-dynamic force value influencing the shaft. Pressure increase from 0.1 to 10 MPa causes growth of gas-dynamic force oscillation amplitude and frequency. The phase shift angle between gas-dynamic force oscillations and those of shaft displacement decreases from 3π/4 to π/2. Damping constant has maximum value under 1 MPa pressure in the gap. Increase of shaft oscillation frequency from 50 to 150 Hz under P=10 MPa causes growth of gas-dynamic force oscillation amplitude. Damping constant has maximum value at 50 Hz equaling 1.012. Increase of shaft vibration amplitude from 20 to 80 µm under P=10 MPa causes the rise of gas-dynamic force amplitude up to 20 times. Damping constant increases from 0.092 to 0.251. Calculations for various working substances (methane, perfect gas, air at 25 ˚С) prove the minimum gas-dynamic force persistent oscillating amplitude under P=0.1 MPa being observed in methane, and maximum in the air. Frequency remains almost unchanged and the phase shift in the air changes from 3π/4 to π/2. Calculations for various working substances (methane, perfect gas, air at 25 ˚С) prove the maximum gas-dynamic force oscillating amplitude under P=10 MPa being observed in methane, and minimum in the air. Air demonstrates surging. Increase of leakage speed from 0 to 20 m/s through LP under P=0.1 MPa causes the gas-dynamic force oscillating amplitude to decrease by 3 orders and oscillation frequency and the phase shift to increase 2 times and stabilize. Increase of leakage speed from 0 to 20 m/s in LP under P=1 MPa causes gas-dynamic force oscillating amplitude to decrease by almost 4 orders. The phase shift angle increases from π/72 to π/2. Oscillations become persistent. Flow rate proved to influence greatly on pressure oscillations amplitude and a phase shift angle. Work medium influence depends on operation conditions. At pressure growth, vibrations are mostly affected in methane (of working substances list considered), and at pressure decrease, in the air at 25 ˚С.
Abstract: At present, vibrations of rotors of gas transmittal unit evade sustainable forecasting. This paper describes elastic oscillation modes in resilient supports and rotor impellers modeled during computational experiments with regard to interference in the system of gas-dynamic flow and compressor rotor. Verification of aeroelastic approach was done on model problem of interaction between supersonic jet in shock tube with deformed plate. ANSYS 15.0 engineering analysis system was used as a modeling tool of numerical simulation in this paper. Finite volume method for gas dynamics and finite elements method for assessment of the strain stress state (SSS) components were used as research methods. Rotation speed and material’s elasticity modulus varied during calculations, and SSS components and gas-dynamic parameters in the dynamic system of gas-dynamic flow and compressor rotor were evaluated. The analysis of time dependence demonstrated that gas-dynamic parameters near the rotor blades oscillate at 200 Hz, and SSS parameters at the upper blade edge oscillate four times higher, i.e. with blade frequency. It has been detected that vibration amplitudes correction in the test points at magnetic bearings by aeroelasticity may correspond up to 50%, and about -π/4 for phases.
Abstract: Interaction between mixing and crystallization is often
ignored despite the fact that it affects almost every aspect of the
operation including nucleation, growth, and maintenance of the
crystal slurry. This is especially pronounced in multiple impeller
systems where flow complexity is increased. By choosing proper
mixing parameters, what closely depends on the knowledge of the
hydrodynamics in a mixing vessel, the process of batch cooling
crystallization may considerably be improved. The values that render
useful information when making this choice are mixing time and
power consumption. The predominant motivation for this work was
to investigate the extent to which radial dual impeller configuration
influences mixing time, power consumption and consequently the
values of metastable zone width and nucleation rate. In this research,
crystallization of borax was conducted in a 15 dm3 baffled batch
cooling crystallizer with an aspect ratio (H/T) of 1.3. Mixing was
performed using two straight blade turbines (4-SBT) mounted on the
same shaft that generated radial fluid flow. Experiments were
conducted at different values of N/NJS ratio (impeller speed/
minimum impeller speed for complete suspension), D/T ratio
(impeller diameter/crystallizer diameter), c/D ratio (lower impeller
off-bottom clearance/impeller diameter), and s/D ratio (spacing
between impellers/impeller diameter). Mother liquor was saturated at
30°C and was cooled at the rate of 6°C/h. Its concentration was
monitored in line by Na-ion selective electrode. From the values of
supersaturation that was monitored continuously over process time, it
was possible to determine the metastable zone width and
subsequently the nucleation rate using the Mersmann’s nucleation
criterion. For all applied dual impeller configurations, the mixing
time was determined by potentiometric method using a pulse
technique, while the power consumption was determined using a
torque meter produced by Himmelstein & Co. Results obtained in
this investigation show that dual impeller configuration significantly
influences the values of mixing time, power consumption as well as
the metastable zone width and nucleation rate. A special attention
should be addressed to the impeller spacing considering the flow
interaction that could be more or less pronounced depending on the
spacing value.
Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: In this article, the radial displacement error correction
capability of a high precision spindle grinding caused by unbalance
force was investigated. The spindle shaft is considered as a flexible
rotor mounted on two sets of angular contact ball bearing. Finite
element methods (FEM) have been adopted for obtaining the
equation of motion of the spindle. In this paper, firstly, natural
frequencies, critical frequencies, and amplitude of the unbalance
response caused by residual unbalance are determined in order to
investigate the spindle behaviors. Furthermore, an optimization
design algorithm is employed to minimize radial displacement of the
spindle which considers dimension of the spindle shaft, the dynamic
characteristics of the bearings, critical frequencies and amplitude of
the unbalance response, and computes optimum spindle diameters
and stiffness and damping of the bearings. Numerical simulation
results show that by optimizing the spindle diameters, and stiffness
and damping in the bearings, radial displacement of the spindle can
be reduced. A spindle about 4 μm radial displacement error can be
compensated with 2 μm accuracy. This certainly can improve the
accuracy of the product of machining.
Abstract: An analytical 4-DOF nonlinear model of a de Laval
rotor-stator system based on Energy Principles has been used
theoretically and experimentally to investigate fault symptoms in a
rotating system. The faults, namely rotor-stator-rub, crack and
unbalance are modeled as excitations on the rotor shaft. Mayes
steering function is used to simulate the breathing behaviour of the
crack. The fault analysis technique is based on waveform signal,
orbits and Fast Fourier Transform (FFT) derived from simulated and
real measured signals. Simulated and experimental results manifest
considerable mutual resemblance of elliptic-shaped orbits and FFT
for a same range of test data.
Abstract: Lots of motors have been being used in industry.
Therefore many researchers have studied about the failure diagnosis of
motors. In this paper, the effect of measuring environment for
diagnosis of gear fault connected to a motor shaft is studied. The fault
diagnosis is executed through the comparison of normal gear and
abnormal gear. The measured FFT data are compared with the normal
data and analyzed for q-axis current, noise and vibration. For bad and
good environment, the diagnosis results are compared. From these, it
is shown that the bad measuring environment may not be able to detect
exactly the motor gear fault. Therefore it is emphasized that the
measuring environment should be carefully prepared.
Abstract: In more complex systems, such as automotive
gearbox, a rigorous treatment of the data is necessary because there
are several moving parts (gears, bearings, shafts, etc.), and in this
way, there are several possible sources of errors and also noise. The
basic objective of this work is the detection of damage in automotive
gearbox. The detection methods used are the wavelet method, the
bispectrum; advanced filtering techniques (selective filtering) of
vibrational signals and mathematical morphology. Gearbox vibration
tests were performed (gearboxes in good condition and with defects)
of a production line of a large vehicle assembler. The vibration
signals are obtained using five accelerometers in different positions
of the sample. The results obtained using the kurtosis, bispectrum,
wavelet and mathematical morphology showed that it is possible to
identify the existence of defects in automotive gearboxes.
Abstract: The article presents two mathematical models of the
interaction between a rotating shaft and an incompressible fluid. The
mathematical model includes both the journal bearings and the
axially traversed hydrodynamic sealing gaps of hydraulic machines.
A method is shown for the identification of additional effects of the
fluid acting on the rotor of the machine, both for a linear and a nonlinear
model. The interaction is expressed by matrices of mass,
stiffness and damping.
Abstract: In this paper, an analytical simplified method for
calculating elasto-plastic stresses strains of notched bodies subject to
non-proportional loading paths is discussed. The method was based
on the Neuber notch correction, which relates the incremental elastic
and elastic-plastic strain energy densities at the notch root and the
material constitutive relationship. The validity of the method was
presented by comparing computed results of the proposed model
against finite element numerical data of notched shaft. The
comparison showed that the model estimated notch-root elasto-plastic
stresses strains with good accuracy using linear-elastic stresses. The
prosed model provides more efficient and simple analysis method
preferable to expensive experimental component tests and more
complex and time consuming incremental non-linear FE analysis.
The model is particularly suitable to perform fatigue life and fatigue
damage estimates of notched components subjected to nonproportional
loading paths.
Abstract: Transmission shafts are affected by various forces, for
example, during acceleration or sudden breaks, bending during
transportation, vertical forces that lead to cuts. One of the main
failures in combines is breaking shaft which repairmen refer it.
Structural resistance of canal against torque is very important in the
beginning of the movement. For analyzing stress, a typical sample
from a type of combine was selected, called JD955 combine. Long
shaft in this combine was analyzed with finite element method by
Ansys13 generic package under static load. Conducted analysis
showed that there is a maximum stress in contact surfaces of
indentations and also in place of changing diameter. Safety factor
value is low in parts of the shaft and this increases the probability of
failure at these points. To improve the conditions with the least cost
and an approach of product improvement, using alternative alloy is
important.
Abstract: The paper deals with possibilities of interpretation of
iron ore reducibility tests. It presents a mathematical model
developed at Centre ENET, VŠB – Technical University of Ostrava,
Czech Republic for an evaluation of metallurgical material of blast
furnace feedstock such as iron ore, sinter or pellets. According to the
data from the test, the model predicts its usage in blast furnace
technology and its effects on production parameters of shaft
aggregate. At the beginning, the paper sums up the general concept
and experience in mathematical modelling of iron ore reduction. It
presents basic equation for the calculation and the main parts of the
developed model. In the experimental part, there is an example of
usage of the mathematical model. The paper describes the usage of
data for some predictive calculation. There are presented material,
method of carried test of iron ore reducibility. Then there are
graphically interpreted effects of used material on carbon
consumption, rate of direct reduction and the whole reduction
process.
Abstract: The paper presents a thermodynamic cycle analysis
for three turboshaft engines. The first cycle is a Brayton cycle,
describing the evolution of a classical turboshaft, based on the
Klimov TV2 engine. The other four cycles aim at approaching an
Ericsson cycle, by replacing the Brayton cycle adiabatic expansion in
the turbine by quasi-isothermal expansion. The maximum quasi-
Ericsson cycles temperature is set to a lower value than the maximum
Brayton cycle temperature, equal to the Brayton cycle power turbine
inlet temperature, in order to decrease the engine NOx emissions.
Also, the power/expansion ratio distribution over the stages of the gas
generator turbine is maintained the same. In two of the considered
quasi-Ericsson cycles, the efficiencies of the gas generator turbine, as
well as the power/expansion ratio distribution over the stages of the
gas generator turbine are maintained the same as for the reference
case, while for the other two cases, the efficiencies are increased in
order to obtain the same shaft power as in the reference case. For the
two cases respecting the first condition, both the shaft power and the
thermodynamic efficiency of the engine decrease, while for the other
two, the power and efficiency are maintained, as a result of assuming
new, more efficient gas generator turbines.
Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: Collection of storm water runoff and forcing it into the
groundwater is the need of the hour to sustain the ground water table.
However, the runoff entraps various types of sediments and other
floating objects whose removal are essential to avoid pollution of
ground water and blocking of pores of aquifer. However, it requires
regular cleaning and maintenance due to problem of clogging. To
evaluate the performance of filter system consisting of coarse sand
(CS), gravel (G) and pebble (P) layers, a laboratory experiment was
conducted in a rectangular column. The effect of variable thickness
of CS, G and P layers of the filtration unit of the recharge shaft on the
recharge rate and the sediment concentration of effluent water were
evaluated.
Medium sand (MS) of three particle sizes, viz. 0.150–0.300 mm
(T1), 0.300–0.425 mm (T2) and 0.425–0.600 mm of thickness 25 cm,
30 cm and 35 cm respectively in the top layer of the filter system and
having seven influent sediment concentrations of 250–3,000 mg/l
were used for experimental study. The performance was evaluated in
terms of recharge rates and clogging time. The results indicated that
100 % suspended solids were entrapped in the upper 10 cm layer of
MS, the recharge rates declined sharply for influent concentrations of
more than 1,000 mg/l. All treatments with higher thickness of MS
media indicated recharge rate slightly more than that of all treatment
with lower thickness of MS media respectively. The performance of
storm water infiltration systems was highly dependent on the
formation of a clogging layer at the filter. An empirical relationship
has been derived between recharge rates, inflow sediment load, size
of MS and thickness of MS with using MLR.
Abstract: This study concerned the dynamic behavior of the
wind turbine rotor. Before all we have studied the loads applied to the
rotor, which allows the knowledge their effect on the fatigue, also
studied the rotor with longitudinal crack in order to determine stress,
strain and displacement. Firstly we compared the first six modes
shapes between cracking and uncracking of HAWT rotor. Secondly
we show show evolution of first six natural frequencies with
longitudinal crack propagation. Finally we conclude that the residual
change in the natural frequencies can be used as in shaft crack
diagnosis predictive maintenance.