Abstract: Three-phase induction machines are today a standard
for industrial electrical drives. Cost, reliability, robustness and maintenance free operation are among the reasons these machines are
replacing dc drive systems. The development of power electronics
and signal processing systems has eliminated one of the greatest
disadvantages of such ac systems, which is the issue of control. With
modern techniques of field oriented vector control, the task of
variable speed control of induction machines is no longer a
disadvantage. The need to increase system performance, particularly
when facing limits on the power ratings of power supplies and
semiconductors, motivates the use of phase number other than three,
In this paper a novel scheme of connecting two, three phase
induction motors in parallel fed by two inverters; viz. VSI and CSI
and their vector control is presented.
Abstract: Multiphasing of dc-dc converters has been known to give technical and economical benefits to low voltage high power buck regulator modules. A major advantage of multiphasing dc-dc converters is the improvement of input and output performances in the buck converter. From this aspect, a potential use would be in renewable energy where power quality plays an important factor. This paper presents the design of a 2-phase 200W boost converter for battery charging application. Analysis of results from hardware measurement of the boost converter demonstrates the benefits of using multiphase. Results from the hardware prototype of the 2-phase boost converter further show the potential extension of multiphase beyond its commonly used low voltage high current domains.
Abstract: The development of the power electronics has allowed
increasing the precision and reliability of the electrical devices, thanks
to the adjustable inverters, as the Pulse Wide Modulation (PWM)
applied to the three level inverters, which is the object of this study.
The authors treat the relation between the law order adopted for a
given system and the oscillations of the electrical and mechanical
parameters of which the tolerance depends on the process with which
they are integrated (paper factory, lifting of the heavy loads,
etc.).Thus, the best choice of the regulation indexes allows us to
achieve stability and safety training without investment (management
of existing equipment). The optimal behavior of any electric device
can be achieved by the minimization of the stored electrical and
mechanical energy.
Abstract: When designing satellites, one of the major issues aside for designing its primary subsystems is to devise its thermal. The thermal management of satellites requires solving different sets of issues with regards to modelling. If the satellite is well conditioned all other parts of the satellite will have higher temperature no matter what. The main issue of thermal modelling for satellite design is really making sure that all the other points of the satellite will be within the temperature limits they are designed. The insertion of power electronics in aerospace technologies is becoming widespread and the modern electronic systems used in space must be reliable and efficient with thermal management unaffected by outer space constraints. Many advanced thermal management techniques have been developed in recent years that have application in high power electronic systems. This paper presents a Three-Dimensional Modal Transmission Line Matrix (3D-TLM) implementation of transient heat flow in space power electronics. In such kind of components heat dissipation and good thermal management are essential. Simulation provides the cheapest tool to investigate all aspects of power handling. The 3DTLM has been successful in modeling heat diffusion problems and has proven to be efficient in terms of stability and complex geometry. The results show a three-dimensional visualisation of self-heating phenomena in the device affected by outer space constraints, and will presents possible approaches for increasing the heat dissipation capability of the power modules.
Abstract: This paper focuses on developing an integrated
reliable and sophisticated model for ultra large wind turbines And to
study the performance and analysis of vector control on large wind
turbines. With the advance of power electronics technology, direct
driven multi-pole radial flux PMSG (Permanent Magnet Synchronous
Generator) has proven to be a good choice for wind turbines
manufacturers. To study the wind energy conversion systems, it is
important to develop a wind turbine simulator that is able to produce
realistic and validated conditions that occur in real ultra MW wind
turbines. Three different packages are used to simulate this model,
namely, Turbsim, FAST and Simulink. Turbsim is a Full field wind
simulator developed by National Renewable Energy Laboratory
(NREL). The wind turbine mechanical parts are modeled by FAST
(Fatigue, Aerodynamics, Structures and Turbulence) code which is
also developed by NREL. Simulink is used to model the PMSG, full
scale back to back IGBT converters, and the grid.
Abstract: A numbers of important developments have led to an
increasing attractiveness for very high speed electrical machines
(either motor or generator). Specifically the increasing switching
speed of power electronics, high energy magnets, high strength
retaining materials, better high speed bearings and improvements in
design analysis are the primary drivers in a move to higher speed. The
design challenges come in the mechanical design both in terms of
strength and resonant modes and in the electromagnetic design
particularly in respect of iron losses and ac losses in the various
conducting parts including the rotor. This paper describes detailed
design work which has been done on a 50,000 rpm, 50kW permanent
magnet( PM) synchronous machine. It describes work on
electromagnetic and rotor eddy current losses using a variety of
methods including both 2D finite element analysis
Abstract: Standard packaging and interconnection technologies
of power devices have difficulties meeting the increasing thermal
demands of new application fields of power electronics devices.
Main restrictions are the decreasing reliability of bond-wires and
solder layers with increasing junction temperature. In the last few
years intensive efforts have been invested in developing new
packaging and interconnection solutions which may open a path to
future application of power devices. In this paper, the main failure
mechanisms of power devices are described and principle of new
packaging and interconnection concepts and their power cycling
reliability are presented.
Abstract: By analyzing the sources of energy and power
loss in PWM (Pulse Width Modulation) controlled drivers of
water electrolysis cells, it is possible to reduce the power
dissipation and enhance the efficiency of such hydrogen
production units. A PWM controlled power driver is based on
a semiconductor switching element where its power
dissipation might be a remarkable fraction of the total power
demand of an electrolysis system. Power dissipation in a
semiconductor switching element is related to many different
parameters which could be fitted into two main categories:
switching losses and conduction losses. Conduction losses are
directly related to the built, structure and capabilities of a
switching device itself and indeed the conditions in which the
element is handling the switching application such as voltage,
current, temperature and of course the fabrication technology.
On the other hand, switching losses have some other
influencing variables other than the mentioned such as control
system, switching method and power electronics circuitry of
the PWM power driver. By analyzings the characteristics of
recently developed power switching transistors from different
families of Bipolar Junction Transistors (BJT), Metal Oxide
Semiconductor Field Effect Transistors (MOSFET) and
Insulated Gate Bipolar Transistors (IGBT), some
recommendations are made in this paper which are able to
lead to achieve higher hydrogen production efficiency by
utilizing PWM controlled water electrolysis cells.