Abstract: Instead of representing individual cognition only, population cognition is represented using artificial neural networks whilst maintaining individuality. This population network trains continuously, simulating adaptation. An implementation of two coexisting populations is compared to the Lotka-Volterra model of predator-prey interaction. Applications include multi-agent systems such as artificial life or computer games.
Abstract: An improved topology of a voltage-fed quasi-resonant
soft switching LCrCdc series-parallel half bridge inverter with a constant-frequency for electronic ballast applications is proposed in this paper. This new topology introduces a low-cost solution to
reduce switching losses and circuit rating to achieve high-efficiency
ballast. Switching losses effect on ballast efficiency is discussed
through experimental point of view. In this discussion, an improved
topology in which accomplishes soft switching operation over a wide
power regulation range is proposed. The proposed structure uses reverse recovery diode to provide better operation for the ballast system. A symmetrical pulse wide modulation (PWM) control scheme is implemented to regulate a wide range of out-put power.
Simulation results are kindly verified with the experimental
measurements obtained by ballast-lamp laboratory prototype. Different load conditions are provided in order to clarify the
performance of the proposed converter.
Abstract: Advancements in the field of artificial intelligence
(AI) made during this decade have forever changed the way we look
at automating spacecraft subsystems including the electrical power
system. AI have been used to solve complicated practical problems
in various areas and are becoming more and more popular nowadays.
In this paper, a mathematical modeling and MATLAB–SIMULINK
model for the different components of the spacecraft power system is
presented. Also, a control system, which includes either the Neural
Network Controller (NNC) or the Fuzzy Logic Controller (FLC) is
developed for achieving the coordination between the components of
spacecraft power system as well as control the energy flows. The
performance of the spacecraft power system is evaluated by
comparing two control systems using the NNC and the FLC.
Abstract: As is known, one of the priority directions of research
works of natural sciences is introduction of applied section of
contemporary mathematics as approximate and numerical methods to
solving integral equation into practice. We fare with the solving of
integral equation while studying many phenomena of nature to whose
numerically solving by the methods of quadrature are mainly applied.
Taking into account some deficiency of methods of quadrature for
finding the solution of integral equation some sciences suggested of
the multistep methods with constant coefficients. Unlike these papers,
here we consider application of hybrid methods to the numerical
solution of Volterra integral equation. The efficiency of the suggested
method is proved and a concrete method with accuracy order p = 4
is constructed. This method in more precise than the corresponding
known methods.
Abstract: In switch mode power inverters, small sized inverters
can be obtained by increasing the switching frequency. Switching
frequency increment causes high driver losses. Also, high dt
di
and
dt
dv
produced by the switching action creates high Electromagnetic
Interference (EMI) and Radio Frequency Interference (RFI). In this
paper, a series half bridge series resonant inverter circuit is simulated
and evaluated practically to demonstrate the turn-on and turn-off
conditions during zero or close to zero voltage switching. Also, the
reverse recovery current effects of the body diode of the MOSFETs
were investigated by operating above and below resonant frequency.
Abstract: A 2.4GHz (RF) down conversion Gilbert Cell mixer,
implemented in a 0.18-μm CMOS technology with a 1.8V supply, is
presented. Current bleeding (charge injection) technique has been
used to increase the conversion gain and the linearity of the mixer.
The proposed mixer provides 10.75 dB conversion gain ( C G ) with
14.3mw total power consumption. The IIP3 and 1-dB compression
point of the mixer are 8dbm and -4.6dbm respectively, at 300 MHz
IF frequencies. Comparing the current design against the
conventional mixer design, demonstrates better performance in the
conversion gain, linearity, noise figure and port-to-port isolation.
Abstract: Solar Cells are destined to supply electric energy beginning from primary resources. It can charge a battery up to 12V dc. For residential use an inverter for 12V dc to 220Vac conversion is desired. For this a static DC-AC converter is necessarily inserted between the solar cells and the distribution network. This paper describes a new P.W.M. strategy for a voltage source inverter. This modulation strategy reduces the energy losses and harmonics in the P.W.M. voltage source inverter. This technique allows the P.W.M. voltage source inverter to become a new feasible solution for solar home application.
Abstract: This paper provides the design steps of a robust Linear
Matrix Inequality (LMI) based iterative multivariable PID controller
whose duty is to drive a sample power system that comprises a
synchronous generator connected to a large network via a step-up
transformer and a transmission line. The generator is equipped with
two control-loops, namely, the speed/power (governor) and voltage
(exciter). Both loops are lumped in one where the error in the
terminal voltage and output active power represent the controller
inputs and the generator-exciter voltage and governor-valve position
represent its outputs. Multivariable PID is considered here because of
its wide use in the industry, simple structure and easy
implementation. It is also preferred in plants of higher order that
cannot be reduced to lower ones. To improve its robustness to
variation in the controlled variables, H∞-norm of the system transfer
function is used. To show the effectiveness of the controller, divers
tests, namely, step/tracking in the controlled variables, and variation
in plant parameters, are applied. A comparative study between the
proposed controller and a robust H∞ LMI-based output feedback is
given by its robustness to disturbance rejection. From the simulation
results, the iterative multivariable PID shows superiority.
Abstract: Losses reduction initiatives in distribution systems
have been activated due to the increasing cost of supplying
electricity, the shortage in fuel with ever-increasing cost to produce
more power, and the global warming concerns. These initiatives have
been introduced to the utilities in shape of incentives and penalties.
Recently, the electricity distribution companies in Oman have been
incentivized to reduce the distribution technical and non-technical
losses with an equal annual reduction rate for 6 years. In this paper,
different techniques for losses reduction in Mazoon Electricity
Company (MZEC) are addressed. In this company, high numbers of
substation and feeders were found to be non-compliant with the
Distribution System Security Standard (DSSS). Therefore, 33
projects have been suggested to bring non-complying 29 substations
and 28 feeders to meet the planed criteria and to comply with the
DSSS. The largest part of MZEC-s network (South Batinah region)
was modeled by ETAP software package. The model has been
extended to implement the proposed projects and to examine their
effects on losses reduction. Simulation results have shown that the
implementation of these projects leads to a significant improvement
in voltage profile, and reduction in the active and the reactive power
losses. Finally, the economical analysis has revealed that the
implementation of the proposed projects in MZEC leads to an annual
saving of about US$ 5 million.
Abstract: A gold coated copper rotating electrode was used to
eliminate surface oxidation effect. This study examined the effect of
electrode rotation on the ozone generation process and showed that an
ozonizer with an electrode rotating system might be a possible way to
increase ozone-synthesis efficiency. Two new phenomena appeared
during experiments with the rotating electrode. First was that ozone
concentration increased to about two times higher than that of the case
with no rotation. Second, input power and discharge area were found
to increase with the rotation speed. Both ozone concentration and
ozone production efficiency improved in the case of rotating electrode
compared to the case with a non-rotating electrode. One possible
reason for this was the increase in discharge length of
micro-discharges during electrode rotation. The rotating electrode
decreased onset voltage, while reactor capacitance increased with
rotation. Use of a rotating-type electrode allowed earlier observation
of the ozone zero phenomena compared with a non-rotating electrode
because, during rotation, the entire electrode surface was functional,
allowing nitrogen on the electrode surface to be evenly consumed.
Nitrogen demand increased with increasing rotation s
Abstract: This paper aims to present the reviews of the
application of neural network in shunt active power filter (SAPF).
From the review, three out of four components of SAPF structure,
which are harmonic detection component, compensating current
control, and DC bus voltage control, have been adopted some of
neural network architecture as part of its component or even
substitution. The objectives of most papers in using neural network in
SAPF are to increase the efficiency, stability, accuracy, robustness,
tracking ability of the systems of each component. Moreover,
minimizing unneeded signal due to the distortion is the ultimate goal
in applying neural network to the SAPF. The most famous
architecture of neural network in SAPF applications are ADALINE
and Backpropagation (BP).
Abstract: Simultaneous recovery of copper and DCA from
simulated MEUF concentrated stream was investigated. Effects of
surfactant (DCA) and metal (copper) concentrations, surfactant to
metal molar ratio (S/M ratio), electroplating voltage, EDTA
concentration, solution pH, and salt concentration on metal recovery
and current efficiency were studied. Electric voltage of -0.5 V was
shown to be optimum operation condition in terms of Cu recovery,
current efficiency, and surfactant recovery. Increasing Cu recovery and
current efficiency were observed with increases of Cu concentration
while keeping concentration of DCA constant. However, increasing
both Cu and DCA concentration while keeping S/M ratio constant at
2.5 showed detrimental effect on Cu recovery at DCA concentration
higher than 15 mM. Cu recovery decreases with increasing pH while
current efficiency showed an opposite trend. It is believed that
conductivity is the main cause for discrepancy of Cu recovery and
current efficiency observed at different pH. Finally, it was shown that
EDTA had adverse effect on both Cu recovery and current efficiency
while addition of NaCl salt had negative impact on current efficiency
at concentration higher than 8000 mg/L.
Abstract: XML has become a popular standard for information exchange via web. Each XML document can be presented as a rooted, ordered, labeled tree. The Node label shows the exact position of a node in the original document. Region and Dewey encoding are two famous methods of labeling trees. In this paper, we propose a new insert friendly labeling method named IFDewey based on recently proposed scheme, called Extended Dewey. In Extended Dewey many labels must be modified when a new node is inserted into the XML tree. Our method eliminates this problem by reserving even numbers for future insertion. Numbers generated by Extended Dewey may be even or odd. IFDewey modifies Extended Dewey so that only odd numbers are generated and even numbers can then be used for a much easier insertion of nodes.
Abstract: Simultaneous transient conduction and radiation heat
transfer with heat generation is investigated. Analysis is carried out
for both steady and unsteady situations. two-dimensional gray
cylindrical enclosure with an absorbing, emitting, and isotropically
scattering medium is considered. Enclosure boundaries are assumed
at specified temperatures. The heat generation rate is considered
uniform and constant throughout the medium. The lattice Boltzmann
method (LBM) was used to solve the energy equation of a transient
conduction-radiation heat transfer problem. The control volume finite
element method (CVFEM) was used to compute the radiative
information. To study the compatibility of the LBM for the energy
equation and the CVFEM for the radiative transfer equation, transient
conduction and radiation heat transfer problems in 2-D cylindrical
geometries were considered. In order to establish the suitability of the
LBM, the energy equation of the present problem was also solved
using the the finite difference method (FDM) of the computational
fluid dynamics. The CVFEM used in the radiative heat transfer was
employed to compute the radiative information required for the
solution of the energy equation using the LBM or the FDM (of the
CFD). To study the compatibility and suitability of the LBM for the
solution of energy equation and the CVFEM for the radiative
information, results were analyzed for the effects of various
parameters such as the boundary emissivity. The results of the LBMCVFEM
combination were found to be in excellent agreement with
the FDM-CVFEM combination. The number of iterations and the
steady state temperature in both of the combinations were found
comparable. Results are found for situations with and without heat
generation. Heat generation is found to have significant bearing on
temperature distribution.
Abstract: In this paper, investigation of subsynchronous
resonance (SSR) characteristics of a hybrid series compensated
system and the design of voltage controller for three level 24-pulse
Voltage Source Converter based Static Synchronous Series
Compensator (SSSC) is presented. Hybrid compensation consists of
series fixed capacitor and SSSC which is a active series FACTS
controller. The design of voltage controller for SSSC is based on
damping torque analysis, and Genetic Algorithm (GA) is adopted for
tuning the controller parameters. The SSR Characteristics of SSSC
with constant reactive voltage control modes has been investigated.
The results show that the constant reactive voltage control of SSSC
has the effect of reducing the electrical resonance frequency, which
detunes the SSR.The analysis of SSR with SSSC is carried out based
on frequency domain method, eigenvalue analysis and transient
simulation. While the eigenvalue and damping torque analysis are
based on D-Q model of SSSC, the transient simulation considers both
D-Q and detailed three phase nonlinear system model using
switching functions.
Abstract: Convergence of power series solutions for a class of
non-linear Abel type equations, including an equation that arises
in nonlinear cooling of semi-infinite rods, is very slow inside their
small radius of convergence. Beyond that the corresponding power
series are wildly divergent. Implementation of nonlinear sequence
transformation allow effortless evaluation of these power series on
very large intervals..
Abstract: The purpose of planned islanding is to construct a
power island during system disturbances which are commonly
formed for maintenance purpose. However, in most of the cases
island mode operation is not allowed. Therefore distributed
generators (DGs) must sense the unplanned disconnection from the
main grid. Passive technique is the most commonly used method for
this purpose. However, it needs improvement in order to identify the
islanding condition. In this paper an effective method for
identification of islanding condition based on phase space and neural
network techniques has been developed. The captured voltage
waveforms at the coupling points of DGs are processed to extract the
required features. For this purposed a method known as the phase
space techniques is used. Based on extracted features, two neural
network configuration namely radial basis function and probabilistic
neural networks are trained to recognize the waveform class.
According to the test result, the investigated technique can provide
satisfactory identification of the islanding condition in the
distribution system.
Abstract: The objective is to fabricate organic light emitting
diode and to study its degradation process in atmosphere condition in
which PFO as an emitting material and PEDOT:PSS as a hole
injecting material were used on ITO substrate. Thus degradation
process of the OLED was studied upon its current-voltage
characteristic. By fabricating this OLED and obtaining blue light and
analysis of current-voltage characteristic during the time after
fabrication, it was observed that the current of the OLED was
exponentially decreased. Current reduction during the initial hours of
fabrication was outstanding and after few days its reduction rate was
dropped significantly, while the diode was dying.
Abstract: High-voltage power transmission lines are the back
bone of electrical power utilities. The stability and continuous
monitoring of this critical infrastructure is pivotal. Nine-Sigma
representing Eskom Holding SOC limited, South Africa has a major
problem on proactive detection of fallen power lines and real time
sagging measurement together with slipping of such conductors. The
main objective of this research is to innovate RFID technology to
solve this challenge. Various options and technologies such as GPS,
PLC, image processing, MR sensors and etc., have been reviewed
and draw backs were made. The potential of RFID to give precision
measurement will be observed and presented. The future research
will look at magnetic and electrical interference as well as corona
effect on the technology.
Abstract: This paper proposes a synchronized random switching frequency pulse width modulation (SRSFPWM). In this technique, the clock signal is used to control the random noise frequency which is produced by the feedback voltage of a hysteresis circuit. These make the triangular carrier frequency equaling to the random noise frequency in each switching period with the symmetrical positive and negative slopes of triangular carrier. Therefore, there is no error voltage in PWM signal. The PSpice simulated results shown the proposed technique improved the performance in case of low frequency harmonics of PWM signal comparing with conventional random switching frequency PWM.