Abstract: Synthesis gas manufacturing by steam reforming of hydrocarbons is an important industrial process. High endothermic nature of the process makes it one of the most cost and heat intensive processes. In the present work, composite effect of different inert gases on synthesis gas yield, feed gas conversion and temperature distribution along the reactor length has been studied using a heterogeneous model. Mathematical model was developed as a first stage and validated against the existing process models. With the addition of inert gases, a higher yield of synthesis gas is observed. Simultaneously the rector outlet temperature drops to as low as 810 K. It was found that Xenon gives the highest yield and conversion while Helium gives the lowest temperature. Using Xenon inert gas 20 percent reduction in outlet temperature was observed compared to traditional case.
Abstract: Trihalomethanes (THMs) were among the first
disinfection byproducts to be discovered in chlorinated water. The
substances form during a reaction between chlorine and organic
matter in the water. Trihalomethanes are suspected to have negative
effects on birth such as, low birth weight, intrauterine growth
retardation in term births, as well as gestational age and preterm
delivery. There are also some evidences showing these by-products to
be mutagenic and carcinogenic, the greatest amount of evidence being
related to the bladder cancer. However, there exist inconsistencies
regarding such effects of THMs as different studies have provided
different results in this regard. The aim of the present study is to
provide a review of the related researches about the above mentioned
health effects of THMs.
Abstract: The present study conducted experimental investigation on combustion and emission characteristics of compression ignition engine using diesel as pilot fuel and methane, hydrogen and methane/hydrogen mixture as gaseous fuels at 1800 rev min-1. The effect of gaseous fuel on peak cylinder pressure and heat release is modest at low to medium loads. At high load, the high combustion temperature and high quantity of pilot fuel contribute to better combustion efficiency for all kinds of gaseous fuels and increases the peak cylinder pressure. Enrichment of hydrogen in methane gradually increases the peak cylinder pressure. The brake thermal efficiency increases with higher hydrogen fraction at lower loads. Hydrogen addition in methane contributed to a proportional reduction of CO/CO2/HC emission without penalty of NOx. For particulate emission, methane and hydrogen, could both suppress the particle emission. 30% hydrogen fraction in methane is observed to be best in reducing the particulate emission.
Abstract: Zeolite A and MCM-41 have extensive applications in basic science, petrochemical science, energy conservation/storage, medicine, chemical sensor, air purification, environmentally benign composite structure and waste remediation. However, the use of zeolite A and MCM-41 in these areas, especially environmental remediation, are restricted due to prohibitive production cost. Efficient recycling of and resource recovery from coal fly ash has been a major topic of current international research interest, aimed at achieving sustainable development of human society from the viewpoints of energy, economy, and environmental strategy. This project reported an original, novel, green and fast methods to produce nano-porous zeolite A and MCM-41 materials from coal fly ash. For zeolite A, this novel production method allows a reduction by half of the total production time while maintaining a high degree of crystallinity of zeolite A which exists in a narrower particle size distribution. For MCM-41, this remarkably green approach, being an environmentally friendly process and reducing generation of toxic waste, can produce pure and long-range ordered MCM-41 materials from coal fly ash. This approach took 24 h at 25 oC to produce 9 g of MCM-41 materials from 30 g of the coal fly ash, which is the shortest time and lowest reaction temperature required to produce pure and ordered MCM-41 materials (having the largest internal surface area) compared to the values reported in the literature. Performance evaluation of the produced zeolite A and MCM-41 materials in wastewater treatment and air pollution control were reported. The residual fly ash was also converted to zeolite Na-P1 which showed good performance in removal of multi-metal ions in wastewater. In wastewater treatment, compared to commercial-grade zeolite A, adsorbents produced from coal fly ash were effective in removing multi heavy metal ions in water and could be an alternative material for treatment of wastewater. In methane emission abatement, the zeolite A (produced from coal fly ash) achieved similar methane removal efficiency compared to the zeolite A prepared from pure chemicals. This report provides the guidance for production of zeolite A and MCM-41 from coal fly ash by a cost-effective approach which opens potential applications of these materials in environmental industry. Finally, environmental and economic aspects of production of zeolite A and MCM-41 from coal fly ash were discussed.
Abstract: In this study, production possibilities of hydrogen and/or methane via SCWG from black grape residues have been investigated. For this aim, grape residues which remain as a byproduct of the wine making process have been used. Since utilization from grape residues is limited due to the high moisture content, supercritical water gasification is the most convenient method. The effect of the gasification temperature and type of catalyst on supercritical water gasification have been investigated. Gasification experiments were performed in a batch autoclave at four different temperatures 300, 400, 500 and 600°C. K2CO3 and Trona (NaHCO3.Na2CO3·2H2O) were used as catalyst. Real biomass types of black grape residues have been successfully gasified and the product gas (hydrogen, methane, carbon dioxide, carbon monoxide and a small amount of ethane and ethylene) were identified by using gas chromatography. A TOC analyzer was used to determine total organic carbon (TOC) content of aqueous phase. The amounts of carboxylic acids, aldehydes, ketones, furfurals and phenols present in the aqueous solutions were analyzed by high performance liquid chromatography. When the temperature increased from 300°C to 600°C, mol% of H2 in gas products increased. The presence of catalysts improves the hydrogen yield. Trona showed gasification activity to be similar to that of K2CO3. It may be concluded that the use of Trona instead of commercially produced catalysts, can be preferably used in the gasification of biomass in supercritical water.
Abstract: Natural gas is defined as gas obtained from a natural underground reservoir. It generally contains a large quantity of methane along with heavier hydrocarbons such as ethane, propane, isobutene, normal butane; also in the raw state it often contains a considerable amount of non hydrocarbons, such as nitrogen and the acid gases (carbon dioxide and hydrogen sulfide). The acid gases must be removed from natural gas before use. One of the processes witch are use in the industry to remove the acid gases from natural gas is the use of alkanolamine process. In this present paper, a simulation study for an industrial gas sweetening plant has been investigated. The aim of the study is to investigate the effect of using mixing amines as solvent on the gas treatment process using the software Hysys.
Abstract: This paper describes a one-dimensional numerical model for natural gas production from the dissociation of methane hydrate in hydrate-capped gas reservoir under depressurization and thermal stimulation. Some of the hydrate reservoirs discovered are overlying a free-gas layer, known as hydrate-capped gas reservoirs. These reservoirs are thought to be easiest and probably the first type of hydrate reservoirs to be produced. The mathematical equations that can be described this type of reservoir include mass balance, heat balance and kinetics of hydrate decomposition. These non-linear partial differential equations are solved using finite-difference fully implicit scheme. In the model, the effect of convection and conduction heat transfer, variation change of formation porosity, the effect of using different equations of state such as PR and ER and steam or hot water injection are considered. In addition distributions of pressure, temperature, saturation of gas, hydrate and water in the reservoir are evaluated. It is shown that the gas production rate is a sensitive function of well pressure.
Abstract: The present work presents the extraction of copper(II)
from sulphuric acid solutions with Sodium diethyldithiocarbamate
(SDDT), and six different organic diluents: Dichloromethane,
Chloroform, Carbon tetrachloride, Toluene, xylene and Cyclohexane,
were tested. The pair SDDT/Chloroform showed to be the most
selective in removing the copper cations, and hence was considered
throughout the experimental study.
The effects of operating parameters such as the initial concentration
of the extracting agent, the agitation time, the agitation speed and the
acid concentration were considered.
For an initial concentration of Cu (II) of 63 ppm in a 0.5 M sulphuric
acid solution, both with a mass of the extracting agent of 20 mg, an
extraction percentage of about 97.8 % and a distribution coefficient
of 44.42 were obtained, respectively, confirming the performance
of the SDDT-Chloroform pair.
Abstract: The potential, opportunities and drawbacks of biogas
technology use in Turkey are evaluated in this paper. Turkey is
dependent on foreign sources of energy. Therefore, use of biogas
technology would provide a safe way of waste disposal and recovery
of renewable energy, particularly from a sustainable domestic source,
which is less unlikely to be influenced by international price or
political fluctuations. Use of biogas technology would especially
meet the cooking, heating and electricity demand in rural areas and
protect the environment, additionally creating new job opportunities
and improving social-economical conditions.
Abstract: In the past many uneconomic solutions for limitation
and interruption of short-circuit currents in low power applications
have been introduced, especially polymer switch based on the
positive temperature coefficient of resistance (PCTR) concept.
However there are many limitations in the active material, which
consists of conductive fillers. This paper presents a significantly
improved and simplified approach that replaces the existing current
limiters with faster switching elements. Its elegance lies in the
remarkable simplicity and low-cost processes of producing the device
using polyaniline (PANI) doped with methane-sulfonic acid (MSA).
Samples characterized as lying in the metallic and critical regimes of
metal insulator transition have been studied by means of electrical
performance in the voltage range from 1V to 5 V under different
environmental conditions. Moisture presence is shown to increase the
resistivity and also improved its current limiting performance.
Additionally, the device has also been studied for electrical resistivity
in the temperature range 77 K-300 K. The temperature dependence of
the electrical conductivity gives evidence for a transport mechanism
based on variable range hopping in three dimensions.
Abstract: For stricter drinking water regulations in the future, reducing the humic acid and disinfection byproducts in raw water, namely, trihalomethanes (THMs) and haloacetic acids (HAAs) is worthy for research. To investigate the removal of waterborne organic material using a lab-scale of bio-activated carbon filter under different EBCT, the concentrations of humic acid prepared were 0.01, 0.03, 0.06, 0.12, 0.17, 0.23, and 0.29 mg/L. Then we conducted experiments using a pilot plant with in-field of the serially connected bio-activated carbon filters and hollow fiber membrane processes employed in traditional water purification plants. Results showed under low TOC conditions of humic acid in influent (0.69 to 1.03 mg TOC/L) with an EBCT of 30 min, 40 min, and 50 min, TOC removal rates increases with greater EBCT, attaining about 39 % removal rate. The removal rate of THMs and HAAs by BACF was 54.8 % and 89.0 %, respectively.
Abstract: The direct discharge of palm oil mill effluent (POME) wastewater causes serious environmental pollution due to its high chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Traditional ways for POME treatment have both economical and environmental disadvantages. In this study, a membrane anaerobic system (MAS) was used as an alternative, cost effective method for treating POME. Six steady states were attained as a part of a kinetic study that considered concentration ranges of 8,220 to 15,400 mg/l for mixed liquor suspended solids (MLSS) and 6,329 to 13,244 mg/l for mixed liquor volatile suspended solids (MLVSS). Kinetic equations from Monod, Contois and Chen & Hashimoto were employed to describe the kinetics of POME treatment at organic loading rates ranging from 2 to 13 kg COD/m3/d. throughout the experiment, the removal efficiency of COD was from 94.8 to 96.5% with hydraulic retention time, HRT from 400.6 to 5.7 days. The growth yield coefficient, Y was found to be 0.62gVSS/g COD the specific microorganism decay rate was 0.21 d-1 and the methane gas yield production rate was between 0.25 l/g COD/d and 0.58 l/g COD/d. Steady state influent COD concentrations increased from 18,302 mg/l in the first steady state to 43,500 mg/l in the sixth steady state. The minimum solids retention time, which was obtained from the three kinetic models ranged from 5 to 12.3 days. The k values were in the range of 0.35 – 0.519 g COD/ g VSS • d and values were between 0.26 and 0.379 d-1. The solids retention time (SRT) decreased from 800 days to 11.6 days. The complete treatment reduced the COD content to 2279 mg/l equivalent to a reduction of 94.8% reduction from the original.
Abstract: Carboneous catalytical methane decomposition is an
attractive process because it produces two valuable products:
hydrogen and carbon. Furthermore, this reaction does not emit any
green house or hazardous gases. In the present study, experiments
were conducted in a thermo gravimetric analyzer using Fluka 05120
as carboneous catalyst to analyze its effectiveness in methane
decomposition. Various temperatures and methane partial pressures
were chosen and carbon mass gain was observed as a function of
time. Results are presented in terms of carbon formation rate,
hydrogen production and catalytical activity. It is observed that there
is linearity in carbon deposition amount by time at lower reaction
temperature (780 °C). On the other hand, it is observed that carbon
and hydrogen formation rates are increased with increasing
temperature. Finally, we observed that the carbon formation rate is
highest at 950 °C within the range of temperatures studied.
Abstract: This paper describes the designs of a first and second
generation autonomous gas monitoring system and the successful
field trial of the final system (2nd generation). Infrared sensing
technology is used to detect and measure the greenhouse gases
methane (CH4) and carbon dioxide (CO2) at point sources. The
ability to monitor real-time events is further enhanced through the
implementation of both GSM and Bluetooth technologies to
communicate these data in real-time. These systems are robust,
reliable and a necessary tool where the monitoring of gas events in
real-time are needed.
Abstract: Methane is the second most important greenhouse gas
(GHG) after carbon dioxide. Amount of methane emission from
energy sector is increasing day by day with various activities. In
present work, various sources of methane emission from upstream,
middle stream and downstream of oil & gas sectors are identified and
categorised as per IPCC-2006 guidelines. Data were collected from
various oil & gas sector like (i) exploration & production of oil & gas
(ii) supply through pipelines (iii) refinery throughput & production
(iv) storage & transportation (v) usage. Methane emission factors for
various categories were determined applying Tier-II and Tier-I
approach using the collected data. Total methane emission from
Indian Oil & Gas sectors was thus estimated for the year 1990 to
2007.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: An experiment of vented gas explosions involving two
different cylinder vessel volumes (0.2 and 0.0065 m3) was reported,
with equivalence ratio (Φ) ranged from 0.3 to 1.6. Both vessels were
closed at the rear end and fitted at the other side with a circular
orifice plate that gives a constant vent coefficient (K =Av/V2/3) of
16.4. It was shown that end ignition gives higher overpressures than
central ignition, even though most of the published work on venting
uses central ignition. For propane and ethylene, it is found that rich
mixtures gave the highest overpressures and these mixtures are not
considered in current vent design guidance; which the guideline is
based on mixtures giving the maximum flame temperature. A strong
influence of the vessel volume at constant K was found for methane,
propane, ethylene and hydrogen-air explosions. It can be concluded
that self- acceleration of the flame, which is dependent on the
distance of a flame from the ignition and the ‘suction’ at the vent
opening are significant factors affecting the vent flow during
explosion development in vented gas explosion. This additional
volume influence on vented explosions is not taken into account in
the current vent design guidance.
Abstract: In this study, a low temperature sensor highly selective to CO in presence of methane is fabricated by using 4 nm SnO2 quantum dots (QDs) prepared by sonication assisted precipitation. SnCl4 aqueous solution was precipitated by ammonia under sonication, which continued for 2 h. A part of the sample was then dried and calcined at 400°C for 1.5 h and characterized by XRD and BET. The average particle size and the specific surface area of the SnO2 QDs as well as their sensing properties were compared with the SnO2 nano-particles which were prepared by conventional sol-gel method. The BET surface area of sonochemically as-prepared product and the one calcined at 400°C after 1.5 hr are 257 m2/gr and 212 m2/gr respectively while the specific surface area for SnO2 nanoparticles prepared by conventional sol-gel method is about 80m2/gr. XRD spectra revealed pure crystalline phase of SnO2 is formed for both as-prepared and calcined samples of SnO2 QDs. However, for the sample prepared by sol-gel method and calcined at 400°C SnO crystals are detected along with those of SnO2. Quantum dots of SnO2 show exceedingly high sensitivity to CO with different concentrations of 100, 300 and 1000 ppm in whole range of temperature (25- 350°C). At 50°C a sensitivity of 27 was obtained for 1000 ppm CO, which increases to a maximum of 147 when the temperature rises to 225°C and then drops off while the maximum sensitivity for the SnO2 sample prepared by the sol-gel method was obtained at 300°C with the amount of 47.2. At the same time no sensitivity to methane is observed in whole range of temperatures for SnO2 QDs. The response and recovery times of the sensor sharply decreases with temperature, while the high selectivity to CO does not deteriorate.
Abstract: Direct conversion of methane to methanol by partial oxidation in a thermal reactor has a poor yield of about 2% which is less than the expected economical yield of about 10%. Conventional thermal catalytic reactors have been proposed to be superseded by plasma reactors as a promising approach, due to strength of the electrical energy which can break C-H bonds of methane. Among the plasma techniques, non-thermal dielectric barrier discharge (DBD) plasma chemical process is one of the most future promising technologies in synthesizing methanol. The purpose of this paper is presenting a brief review of CH4 oxidation with O2 in DBD plasma reactors based on the recent investigations. For this reason, the effect of various parameters of reactor configuration, feed ratio, applied voltage, residence time (gas flow rate), type of applied catalyst, pressure and reactor wall temperature on methane conversion and methanol selectivity are discussed.
Abstract: Air pollution is a major environmental health
problem, affecting developed and developing countries around the
world. Increasing amounts of potentially harmful gases and
particulate matter are being emitted into the atmosphere on a global
scale, resulting in damage to human health and the environment.
Petroleum-related air pollutants can have a wide variety of adverse
environmental impacts. In the crude oil production sectors, there is a
strong need for a thorough knowledge of gaseous emissions resulting
from the flaring of associated gas of known composition on daily
basis through combustion activities under several operating
conditions. This can help in the control of gaseous emission from
flares and thus in the protection of their immediate and distant
surrounding against environmental degradation.
The impacts of methane and non-methane hydrocarbons emissions
from flaring activities at oil production facilities at Kuwait Oilfields
have been assessed through a screening study using records of flaring
operations taken at the gas and oil production sites, and by analyzing
available meteorological and air quality data measured at stations
located near anthropogenic sources. In the present study the
Industrial Source Complex (ISCST3) Dispersion Model is used to
calculate the ground level concentrations of methane and nonmethane
hydrocarbons emitted due to flaring in all over Kuwait
Oilfields.
The simulation of real hourly air quality in and around oil
production facilities in the State of Kuwait for the year 2006,
inserting the respective source emission data into the ISCST3
software indicates that the levels of non-methane hydrocarbons from
the flaring activities exceed the allowable ambient air standard set by
Kuwait EPA. So, there is a strong need to address this acute problem
to minimize the impact of methane and non-methane hydrocarbons
released from flaring activities over the urban area of Kuwait.