Abstract: The objective of the present study is to numerically investigate the effect of CO2 replacement of N2 in air stream on the flame characteristics of the CH4 turbulent diffusion flame. The Open source Field Operation and Manipulation (OpenFOAM) has been used as the computational tool. In this regard, laminar flamelet and modified k-ε models have been utilized as combustion and turbulence models, respectively. Results reveal that the presence of CO2 in air stream changes the flame shape and maximum flame temperature. Also, CO2 dilution causes an increment in CO mass fraction.
Abstract: Next generation bio-alcohols produced from non-food based sources like cellulosic biomass are promising renewable energy sources. The present study investigates engine performance, combustion characteristics, and emissions of a small single cylinder direct injection diesel engine fueled by four kinds of next generation bio-alcohol isomer and diesel fuel blends with a constant blending ratio of 3:7 (mass). The tested bio-alcohol isomers here are n-butanol and iso-butanol (C4 alcohol), and n-pentanol and iso-pentanol (C5 alcohol). To obtain simultaneous reductions in NOx and smoke emissions, the experiments employed supercharging combined with EGR (Exhaust Gas Recirculation). The boost pressures were fixed at two conditions, 100 kPa (naturally aspirated operation) and 120 kPa (supercharged operation) provided with a roots blower type supercharger. The EGR rates were varied from 0 to 25% using a cooled EGR technique. The results showed that both with and without supercharging, all the bio-alcohol blended diesel fuels improved the trade-off relation between NOx and smoke emissions at all EGR rates while maintaining good engine performance, when compared with diesel fuel operation. It was also found that regardless of boost pressure and EGR rate, the ignition delays of the tested bio-alcohol isomer blends are in the order of iso-butanol > n-butanol > iso-pentanol > n-pentanol. Overall, it was concluded that, except for the changes in the ignition delays the influence of bio-alcohol isomer blends on the engine performance, combustion characteristics, and emissions are relatively small.
Abstract: Hardly any neat biodiesel satisfies the European EN14214 standard for compression ignition engine application. To satisfy the EN14214 standard, various additives are doped into biodiesel; however, biodiesel additives might cause other problems such as increase in the particular emission and increased specific fuel consumption. In addition, the additives could be expensive. Considering the increasing level of greenhouse gas GHG emissions and fossil fuel depletion, it is forecasted that the use of biodiesel will be higher in the near future. Hence, the negative aspects of the biodiesel additives will likely to gain much more importance and need to be replaced with better solutions. This study aims to satisfy the European standard EN14214 by blending the biodiesels derived from sustainable feedstocks. Waste Cooking Oil (WCO) and Animal Fat Oil (AFO) are two sustainable feedstocks in the EU (including the UK) for producing biodiesels. In the first stage of the study, these oils were transesterified separately and neat biodiesels (W100 & A100) were produced. Secondly, the biodiesels were blended together in various ratios: 80% WCO biodiesel and 20% AFO biodiesel (W80A20), 60% WCO biodiesel and 40% AFO biodiesel (W60A40), 50% WCO biodiesel and 50% AFO biodiesel (W50A50), 30% WCO biodiesel and 70% AFO biodiesel (W30A70), 10% WCO biodiesel and 90% AFO biodiesel (W10A90). The prepared samples were analysed using Thermo Scientific Trace 1300 Gas Chromatograph and ISQ LT Mass Spectrometer (GC-MS). The GS-MS analysis gave Fatty Acid Methyl Ester (FAME) breakdowns of the fuel samples. It was found that total saturation degree of the samples was linearly increasing (from 15% for W100 to 54% for A100) as the percentage of the AFO biodiesel was increased. Furthermore, it was found that WCO biodiesel was mainly (82%) composed of polyunsaturated FAMEs. Cetane numbers, iodine numbers, calorific values, lower heating values and the densities (at 15 oC) of the samples were estimated by using the mass percentages data of the FAMEs. Besides, kinematic viscosities (at 40 °C and 20 °C), densities (at 15 °C), heating values and flash point temperatures of the biomixture samples were measured in the lab. It was found that estimated and measured characterisation results were comparable. The current study concluded that biomixture fuel samples W60A40 and W50A50 were perfectly satisfying the European EN 14214 norms without any need of additives. Investigation on engine performance, exhaust emission and combustion characteristics will be conducted to assess the full feasibility of the proposed biomixture fuels.
Abstract: Biodiesel is widely investigated to solve the twin
problem of depletion of fossil fuel and environmental degradation.
The main objective of the present work is to compare performance,
emissions, and combustion characteristics of biodiesel derived from
cotton seed oil in a diesel engine with the baseline results of
petrodiesel fuel. Tests have been conducted on a single cylinder, four
stroke CIDI diesel engine with a speed of 1500 rpm and a fixed
compression ratio of 17.5 at different load conditions. The
performance parameters evaluated include brake thermal efficiency,
brake specific fuel consumption, brake power, indicated mean
effective pressure, mechanical efficiency, and exhaust gas
temperature. Regarding combustion study, cylinder pressure, rate of
pressure rise, net heat release rate, cumulative heat release, mean gas
temperature, mass fraction burned, and fuel line pressure were
evaluated. The emission parameters such as carbon monoxide, carbon
dioxide, un-burnt hydrocarbon, oxides of nitrogen, and smoke
opacity were also measured by a smoke meter and an exhaust gas
analyzer and compared with baseline results. The brake thermal
efficiency of cotton seed oil methyl ester (CSOME) was lower than
that of petrodiesel and brake specific fuel consumption was found to
be higher. However, biodiesel resulted in the reduction of carbon
dioxide, un-burnt hydrocarbon, and smoke opacity at the expense of
nitrogen oxides. Carbon monoxide emissions for biodiesel was higher
at maximum output power. It has been found that the combustion
characteristics of cotton seed oil methyl ester closely followed those
of standard petrodiesel. The experimental results suggested that
biodiesel derived from cotton seed oil could be used as a good
substitute to petrodiesel fuel in a conventional diesel without any
modification.
Abstract: This paper is aimed to study combustion characteristics
of low NOx burner using petroleum cokes as fuel. The petroleum coke,
which is produced through the oil refining process, is an attractive fuel
in terms of its high heating value and low price. But petroleum coke is
a challenging fuel because of its low volatile content, high sulfur and
nitrogen content, which give rise to undesirable emission
characteristics and low ignitability. Therefore, the research and
development regarding the petroleum coke burner is needed for
applying this industrial system. In this study, combustion and emission
characteristics of petroleum cokes burner are experimentally
investigated in an industrial steam boiler. The low NOx burner is
designed to control fuel and air mixing to achieve staged combustion,
which, in turn reduces both flame temperature and oxygen. Air
distribution ratio of triple staged air is optimized experimentally. The
result showed that NOx concentration is lowest when overfire air is
used, and the burner function at a fuel rich condition. That is, the
burner is operated at the equivalence ratio of 1.67 and overall
equivalence ratio including overfire air is kept 0.87.
Abstract: The use of biodiesel in conventional diesel engines results in substantial reduction of unburned hydrocarbon, carbon monoxide and particulate matters. The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio engine when fueled with Karanja (Pongamia) methyl ester and its 10-50 % blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of karanja methyl ester as a biofuel has been established in this study. The useful brake power obtained is similar to diesel fuel for all loads. Experiment has been conducted at a fixed engine speed of 1500 rpm, variable load and at compression ratios of 17.5:1 and 18.5:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for pongamia oil methyl ester when compared to that of diesel. The brake thermal efficiency for pongamia oil methyl ester blends and diesel has been calculated and the blend B20 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions. PME as an oxygenated fuel generated more complete combustion, which means increased torque and power. This is also supported with higher thermal efficiencies of the PME blends. NOx is slightly increased due to the higher combustion temperature and the presence of fuel oxygen with the blend at full load. PME as a new Biodiesel and its blends can be used in diesel engines without any engine modification.
Abstract: Catalytic combustion is generally accepted as an environmentally preferred alternative for the generation of heat and power from fossil fuels mainly due to its advantages related to the stable combustion under very lean conditions with low emissions of NOx, CO, and UHC at temperatures lower than those occurred in conventional flame combustion. Despite these advantages, the commercial application of catalytic combustion has been delayed because of complicated reaction processes and the difficulty in developing appropriate catalysts with the required stability and durability. To develop the catalytic combustors, detailed studies on the combustion characteristics of catalytic combustion should be conducted. To the end, in current research, quantitative studies on the combustion characteristics of the catalytic combustors, with a Pd-based catalyst for MCFC power generation systems, relying on numerical simulations have been conducted. In addition, data from experimental studies of variations in outlet temperatures and fuel conversion, taken after operating conditions have been used to validate the present numerical approach. After introducing the governing equations for mass, momentum, and energy equations as well as a description of catalytic combustion kinetics, the effects of the excess air ratio, space velocity, and inlet gas temperature on the catalytic combustion characteristics are extensively investigated. Quantitative comparisons are also conducted with previous experimental data. Finally, some concluding remarks are presented.
Abstract: The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio multi fuel engine when fueled with different blends of rice bran oil methyl ester and ethanol are investigated and compared with the results of standard diesel. Bio diesel produced from Rice bran oil by transesterification process has been used in this study. Experiment has been conducted at a fixed engine speed of 1500 rpm, 50% load and at compression ratios of 16.5:1, 17:1, 17.5:1 and 18:1. The impact of compression ratio on fuel consumption, brake thermal efficiency and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for waste cooking oil methyl ester when compared to that of diesel. The brake thermal efficiency at 50% load for Rice bran oil methyl ester blends and diesel has been calculated and the blend B40 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions.
Abstract: The experimental results on combustion of rice husk
in a conical fluidized bed combustor (referred to as the conical FBC)
using silica sand as the bed material are presented in this paper. The
effects of excess combustion air and combustor loading as well as the
sand bed height on the combustion pattern in FBC were investigated.
Temperatures and gas concentrations (CO and NO) along over the
combustor height as well as in the flue gas downstream from the ash
collecting cyclone were measured. The results showed that the axial
temperature profiles in FBC were explicitly affected by the
combustor loading whereas the excess air and bed height were found
to have minor influences on the temperature pattern. Meanwhile, the
combustor loading and the excess air significantly affected the axial
CO and NO concentration profiles; however, these profiles were
almost independent of the bed height. The combustion and thermal
efficiencies for this FBC were quantified for different operating
conditions.
Abstract: An effort has been taken to simulate the combustion
and performance characteristics of biodiesel fuel in direct injection
(D.I) low heat rejection (LHR) diesel engine. Comprehensive
analyses on combustion characteristics such as cylinder pressure,
peak cylinder pressure, heat release and performance characteristics
such as specific fuel consumption and brake thermal efficiency are
carried out. Compression ignition (C.I) engine cycle simulation was
developed and modified in to LHR engine for both diesel and
biodiesel fuel. On the basis of first law of thermodynamics the
properties at each degree crank angle was calculated. Preparation and
reaction rate model was used to calculate the instantaneous heat
release rate. A gas-wall heat transfer calculations are based on the
ANNAND-s combined heat transfer model with instantaneous wall
temperature to analyze the effect of coating on heat transfer. The
simulated results are validated by conducting the experiments on the
test engine under identical operating condition on a turbocharged D.I
diesel engine. In this analysis 20% of biodiesel (derived from
Jatropha oil) blended with diesel and used in both conventional and
LHR engine. The simulated combustion and performance
characteristics results are found satisfactory with the experimental
value.
Abstract: The objective of this study is to investigate the
combustion in a pilot-ignited supercharged dual-fuel engine, fueled
with different types of gaseous fuels under various equivalence ratios.
It is found that if certain operating conditions are maintained,
conventional dual-fuel engine combustion mode can be transformed to
the combustion mode with the two-stage heat release. This mode of
combustion was called the PREMIER (PREmixed Mixture Ignition in
the End-gas Region) combustion. During PREMIER combustion,
initially, the combustion progresses as the premixed flame
propagation and then, due to the mixture autoignition in the end-gas
region, ahead of the propagating flame front, the transition occurs with
the rapid increase in the heat release rate.
Abstract: The fabrication of porous NiTi shape memory alloys (SMAs) from elemental powder compacts was conducted by selfpropagating high temperature synthesis (SHS). Effects of the preheating temperature and the chamber pressure on the combustion characteristics as well as the final morphology and the composition of products were studied. The samples with porosity between 56.4 and 59.0% under preheating temperature in the range of 200-300°C and Ar-gas chamber pressure of 138 and 201 kPa were obtained. The pore structures were found to be dissimilar only in the samples processed with different preheating temperature. The major phase in the porous product is NiTi with small amounts of secondary phases, NiTi2 and Ni4Ti3. The preheating temperature and the chamber pressure have very little effect on the phase constituent. While the combustion temperature of the sample was notably increased by increasing the preheating temperature, they were slightly changed by varying the chamber pressure.
Abstract: As the demand and prices of various petroleum products have been on the rise in recent years, there is a growing need for alternative fuels. Biodiesel, which consists of alkyl monoesters of fatty acids from vegetable oils and animal fats, is considered as an alternative to petroleum diesel. Biodiesel has comparable performance with that of diesel and has lower brake specific fuel consumption than diesel with significant reduction in emissions of CO, hydrocarbons (HC) and smoke with however, a slight increase in NOx emissions. This paper analyzes the effect of cooled exhaust gas recirculation in the combustion characteristics of a direct injection compression ignition engine using biodiesel blended fuel as opposed to the conventional system. The combustion parameters such as cylinder pressure, heat release rate, delay period and peak pressure were analyzed at various loads. The maximum cylinder pressure reduces as the fraction of biodiesel increases in the blend the maximum rate of pressure rise was found to be higher for diesel at higher engine loads.
Abstract: Experiments were carried out to evaluate the
influence of the addition of hydrogen to the inlet air on the
performance of a single cylinder direct injection diesel engine.
Hydrogen was injected in the inlet manifold. The addition of
hydrogen was done on energy replacement basis. It was found that
the addition of hydrogen improves the combustion process due to
superior combustion characteristics of hydrogen in comparison to
conventional diesel fuels. It was also found that 10% energy
replacement improves the engine thermal efficiency by about 40%
and reduces the sfc by about 35% however the volumetric efficiency
was reduced by about 35%.
Abstract: Triglycerides and their derivatives are considered as viable alternatives for diesel fuels. Rice bran oil is used as diesel fuel. Highly viscous rice bran oil can be reduced by blending it with diesel fuel. The present research is aimed to investigate experimentally the performance, exhaust emission and combustion characteristics of a direct injection (DI) diesel engine, typically used in agricultural sector, over the entire load range when fuelled with rice bran oil and diesel fuel blends, RB10 (10% rice bran oil + 90% diesel fuel) to RB50. The performance, emission and combustion parameters of RB20 were found to be very close to neat diesel fuel (ND). The injector opening pressure (IOP) undoubtedly is of prime importance in diesel engine operation. Performance, emission and combustion characteristics with RB30 at enhanced IOPs are better than ND. Improved premixed heat release rate were noticed with RB30 when the IOP is enhanced.
Abstract: The mixture formation prior to the ignition process
plays as a key element in the diesel combustion. Parametric studies of
mixture formation and ignition process in various injection parameter
has received considerable attention in potential for reducing
emissions. Purpose of this study is to clarify the effects of injection
pressure on mixture formation and ignition especially during ignition
delay period, which have to be significantly influences throughout the
combustion process and exhaust emissions. This study investigated
the effects of injection pressure on diesel combustion fundamentally
using rapid compression machine. The detail behavior of mixture
formation during ignition delay period was investigated using the
schlieren photography system with a high speed camera. This method
can capture spray evaporation, spray interference, mixture formation
and flame development clearly with real images. Ignition process and
flame development were investigated by direct photography method
using a light sensitive high-speed color digital video camera. The
injection pressure and air motion are important variable that strongly
affect to the fuel evaporation, endothermic and prolysis process
during ignition delay. An increased injection pressure makes spray tip
penetration longer and promotes a greater amount of fuel-air mixing
occurs during ignition delay. A greater quantity of fuel prepared
during ignition delay period thus predominantly promotes more rapid
heat release.
Abstract: Transesterified vegetable oils (biodiesel) are promising alternative fuel for diesel engines. Used vegetable oils are disposed from restaurants in large quantities. But higher viscosity restricts their direct use in diesel engines. In this study, used cooking oil was dehydrated and then transesterified using an alkaline catalyst. The combustion, performance and emission characteristics of Used Cooking oil Methyl Ester (UCME) and its blends with diesel oil are analysed in a direct injection C.I. engine. The fuel properties and the combustion characteristics of UCME are found to be similar to those of diesel. A minor decrease in thermal efficiency with significant improvement in reduction of particulates, carbon monoxide and unburnt hydrocarbons is observed compared to diesel. The use of transesterified used cooking oil and its blends as fuel for diesel engines will reduce dependence on fossil fuels and also decrease considerably the environmental pollution.
Abstract: The present study conducted experimental investigation on combustion and emission characteristics of compression ignition engine using diesel as pilot fuel and methane, hydrogen and methane/hydrogen mixture as gaseous fuels at 1800 rev min-1. The effect of gaseous fuel on peak cylinder pressure and heat release is modest at low to medium loads. At high load, the high combustion temperature and high quantity of pilot fuel contribute to better combustion efficiency for all kinds of gaseous fuels and increases the peak cylinder pressure. Enrichment of hydrogen in methane gradually increases the peak cylinder pressure. The brake thermal efficiency increases with higher hydrogen fraction at lower loads. Hydrogen addition in methane contributed to a proportional reduction of CO/CO2/HC emission without penalty of NOx. For particulate emission, methane and hydrogen, could both suppress the particle emission. 30% hydrogen fraction in methane is observed to be best in reducing the particulate emission.
Abstract: In this study, a 3D combustion chamber was simulated
using FLUENT 6.32. Aim to obtain detailed information on
combustion characteristics and _ nitrogen oxides in the furnace and
the effect of oxygen enrichment in a combustion process. Oxygenenriched
combustion is an effective way to reduce emissions. This
paper analyzes NO emission, including thermal NO and prompt NO.
Flow rate ratio of air to fuel is varied as 1.3, 3.2 and 5.1 and the
oxygen enriched flow rates are 28, 54 and 68 lit/min. The 3D
Reynolds Averaged Navier Stokes (RANS) equations with standard
k-ε turbulence model are solved together by Fluent 6.32 software.
First order upwind scheme is used to model governing equations and
the SIMPLE algorithm is used as pressure velocity coupling. Results
show that for AF=1.3, increase the oxygen flow rate of oxygen
reduction in NO emissions is Lance. Moreover, in a fixed oxygen
enrichment condition, increasing the air to fuel ratio will increase the
temperature peak, but not the NO emission rate. As a result, oxygen
enrichment can reduce the NO emission at this kind of furnace in low
air to fuel rates.
Abstract: The pyrolysis characteristics and kinetics of seven marine biomass, which are fixed Enteromorpha clathrata, floating Enteromorpha clathrata, Ulva lactuca L., Zosterae Marinae L., Thallus Laminariae, Asparagus schoberioides kunth and Undaria pinnatifida (Harv.), were studied with thermogravimetric analysis method. Simultaneously, cornstalk, which is a grass biomass, and sawdust, which is a lignocellulosic biomass, were references. The basic pyrolysis characteristics were studied by using TG- DTG-DTA curves. The results showed that there were three stages (dehydration, dramatic weight loss and slow weight loss) during the whole pyrolysis process of samples. The Tmax of marine biomass was significantly lower than two kinds of terrestrial biomass. Zosterae Marinae L. had a relatively high stability of pyrolysis, but floating Enteromorpha clathrata had lowest stability of pyrolysis and a good combustion characteristics. The corresponding activation energy E and frequency factor A were obtained by Coats-Redfern method. It was found that the pyrolysis reaction mechanism functions of three kinds of biomass are different.