Abstract: Presented in this paper is a framework of a software ‘WEMax’. The WEMax is invented for analysis and simulation for manned assembly lines to sustain and improve performance of manufacturing systems. In a manufacturing system, performance, such as productivity, is a key of competitiveness for output products. However, the manned assembly lines are difficult to forecast performance, because human labors are not expectable factors by computer simulation models or mathematical models. Existing approaches to performance forecasting of the manned assembly lines are limited to matters of the human itself, such as ergonomic and workload design, and non-human-factor-relevant simulation. Consequently, an approach for the forecasting and improvement of manned assembly line performance is needed to research. As a solution of the current problem, this study proposes a framework that is for generation and simulation of virtual manned assembly lines, and the framework has been implemented as a software.
Abstract: The study focuses to investigate the thermal response of delaminations and develop mathematical models using numerical results to obtain the optimum heat requirement and time to identify delaminations in GLARE type of Fibre Metal Laminates (FML) in both reflection mode and through-transmission (TT) mode of step pulsed active thermography (SPAT) method in the type of nondestructive testing and evaluation (NDTE) technique. The influence of applied heat flux and time on various sizes and depth of delaminations in FML is analyzed to investigate the thermal response through numerical simulations. A finite element method (FEM) is applied to simulate SPAT through ANSYS software based on 3D transient heat transfer principle with the assumption of reflection mode and TT mode of observation individually.
The results conclude that the numerical approach based on SPAT in reflection mode is more suitable for analysing smaller size of near-surface delaminations located at the thermal stimulator side and TT mode is more suitable for analysing smaller size of deeper delaminations located far from thermal stimulator side or near thermal detector/Infrared camera side. The mathematical models provide the optimum q and T at the required MRTD to identify unidentified delamination 7 with 25015.0022W/m2 at 2.531sec and delamination 8 with 16663.3356 W/m2 at 1.37857sec in reflection mode. In TT mode, the delamination 1 with 34954W/m2 at 13.0399sec, delamination 2 with 20002.67W/m2 at 1.998sec and delamination 7 with 20010.87 W/m2 at 0.6171sec could be identified.
Abstract: This paper presents a novel Global Navigation Satellite System (GNSS) Avionics Based Integrity Augmentation (ABIA) system architecture suitable for civil and military air platforms, including Unmanned Aircraft Systems (UAS). Taking the move from previous research on high-accuracy Differential GNSS (DGNSS) systems design, integration and experimental flight test activities conducted at the Italian Air Force Flight Test Centre (CSV-RSV), our research focused on the development of a novel approach to the problem of GNSS ABIA for mission- and safety-critical air vehicle applications and for multi-sensor avionics architectures based on GNSS. Detailed mathematical models were developed to describe the main causes of GNSS signal outages and degradation in flight, namely: antenna obscuration, multipath, fading due to adverse geometry and Doppler shift. Adopting these models in association with suitable integrity thresholds and guidance algorithms, the ABIA system is able to generate integrity cautions (predictive flags) and warnings (reactive flags), as well as providing steering information to the pilot and electronic commands to the aircraft/UAS flight control systems. These features allow real-time avoidance of safety-critical flight conditions and fast recovery of the required navigation performance in case of GNSS data losses. In other words, this novel ABIA system addresses all three cornerstones of GNSS integrity augmentation in mission- and safety-critical applications: prediction (caution flags), reaction (warning flags) and correction (alternate flight path computation).
Abstract: Monitoring is essential to assessing the effectiveness of air pollution control actions. The goal of the air quality information system is through monitoring, to keep authorities, major polluters and the public informed on the short and long-term changes in air quality, thereby helping to raise awareness. Mathematical models are the best tools available for the prediction of the air quality management. The main objective of the work was to apply a Model that predicts the concentration levels of different pollutants at any instant of time. In this study, distribution of air pollutants concentration such as nitrogen dioxides (NO2), sulphur dioxides (SO2) and total suspended particulates (TSP) of industries are determined by using Gaussian model. Besides that, the effect of wind speed and its direction on the pollutant concentration within the affected area were evaluated. In order to determine the efficiency and percentage of error in the modeling, validation process of data was done. Sampling of air quality was conducted in getting existing air quality around a factory and the concentrations of pollutants in a plume were inversely proportional to wind velocity. The resultant ground level concentrations were then compared to the quality standards to determine if there could be a negative impact on health. This study concludes that concentration of pollutants can be significantly predicted using Gaussian Model. The data base management is developed for the air data of Hubli-Dharwad region.
Abstract: Modelling is a widely used tool to facilitate the evaluation of disease management. The interest of epidemiological models lies in their ability to explore hypothetical scenarios and provide decision makers with evidence to anticipate the consequences of disease incursion and impact of intervention strategies.
All models are, by nature, simplification of more complex systems. Models that involve diseases can be classified into different categories depending on how they treat the variability, time, space, and structure of the population. Approaches may be different from simple deterministic mathematical models, to complex stochastic simulations spatially explicit.
Thus, epidemiological modelling is now a necessity for epidemiological investigations, surveillance, testing hypotheses and generating follow-up activities necessary to perform complete and appropriate analysis.
The state of the art presented in the following, allows us to position itself to the most appropriate approaches in the epidemiological study.
Abstract: The functional performance of machined components, often, depends on surface topography, hardness, nature of stress and strain induced on the surface, etc. Invariably, surfaces of metallic components obtained by turning, milling, etc., consist of irregularities such as machining marks are responsible for the above. Surface finishing/coating processes used to produce improved surface quality/textures are classified as chip-removal and chip-less processes. Burnishing is chip-less cold working process carried out to improve surface finish, hardness and resistance to fatigue and corrosion; not obtainable by other surface coating and surface treatment processes. It is a very simple, but effective method which improves surface characteristics and is reported to introduce compressive stresses.
Of late, considerable attention is paid to post-machining, finishing operations, such as burnishing. During burnishing the micro-irregularities start to deform plastically, initially the crests are gradually flattened and zones of reduced deformation are formed. When all the crests are deformed, the valleys between the micro-irregularities start moving in the direction of the newly formed surface. The grain structure is then condensed, producing a smoother and harder surface with superior load-carrying and wear-resistant capabilities.
Burnishing can be performed on a lathe with a highly polished ball or roller type tool which is traversed under force over a rotating/stationary work piece. Often, several passes are used to obtain the work piece surface with the desired finish and hardness.
This paper presents the findings of an experimental investigation on the effect of ball burnishing parameters such as, burnishing speed, feed, force and number of passes; on surface roughness (Ra) and micro-hardness (Hv) of a 60/40 copper/zinc alloy, using a 2-level fractional factorial design of experiments (DoE). Mathematical models were developed to predict surface roughness and hardness generated by burnishing in terms of the above process parameters. A ball-type tool, designed and constructed from a high chrome steel material (HRC=63 and Ra=0.012 µm), was used for burnishing of fine-turned cylindrical bars (0.68-0.78µm and 145Hv). They are given by,
Ra= 0.305-0.005X1 - 0.0175X2 + 0.0525X4 + 0.0125X1X4 -0.02X2X4 - 0.0375X3X4
Hv=160.625 -2.37 5X1 + 5.125X2 + 1.875X3 + 4.375X4 - 1.625X1X4 + 4.375X2X4 - 2.375X3X4
High surface microhardness (175HV) was obtained at 400rpm, 2passes, 0.05mm/rev and 15kgf., and high surface finish (0.20µm) was achieved at 30kgf, 0.1mm/rev, 112rpm and single pass. In other words, surface finish improved by 350% and microhardness improved by 21% compared to as machined conditions.
Abstract: Implementing significant advantages in the supply of self-compacting concrete (SCC) is necessary because of the, negative features of SCC. Examples of these features are the ductility problem along with the very high cost of its constituted materials. Silica fume with steel fiber can fix this matter by improving the ductility and decreasing the total cost of SCC by varying the cement ingredients. Many different researchers have found that there have not been enough research carried out on the steel fiber-reinforced self-compacting concrete (SFRSCC) produced with silica fume. This paper inspects both the fresh and the mechanical properties of SFRSCC with silica fume, the fresh qualities where slump flow, slump T50 and V- funnel. While, the mechanical characteristics were the compressive strength, ultrasound pulse velocity (UPV) and elastic modulus of the concrete samples. The experimental results have proven that steel fiber can enhance the mechanical features. In addition, the silica fume within the entire hybrid mix may possibly adapt the fiber dispersion and strengthen deficits due to the fibers. It could also improve the strength plus the bond between the fiber and the matrix with a dense calcium silicate-hydrate gel in SFRSCC. The concluded result was predicted using linear mathematical models and was found to be in great agreement with the experimental results.
Abstract: This paper discusses the application of extreme events distribution taking the Limpopo River Basin at Xai-Xai station, in Mozambique, as a case analysis. We analyze the extreme value concepts, namely Gumbel, Fréchet, Weibull and Generalized Extreme Value Distributions and then extrapolate the original data to 1000, 5000 and 10000 figures for further simulations and we compare their outcomes based on these three main distributions.
Abstract: A filtering problem of almost incompressible liquid chemical compound in the porous inhomogeneous 3D domain is studied. In this work general approaches to the solution of twodimensional filtering problems in ananisotropic, inhomogeneous and multilayered medium are developed, and on the basis of the obtained results mathematical models are constructed (according to Ollendorff method) for studying the certain engineering and technical problem of filtering the almost incompressible liquid chemical compound in the porous inhomogeneous 3D domain. For some of the formulated mathematical problems with additional requirements for the structure of the porous inhomogeneous medium, namely, its isotropy, spatial periodicity of its permeability coefficient, solution algorithms are proposed. Continuation of the current work titled ”On one mathematical model for filtration of weakly compressible chemical compound in the porous heterogeneous 3D medium. Part II: Determination of the reference directions of anisotropy and permeabilities on these directions” will be prepared in the shortest terms by the authors.
Abstract: To reveal the temperature field distribution of disc
brake in downward belt conveyor, mathematical models of heat
transfer for disc brake were established combined with heat transfer
theory. Then, the simulation process was stated in detail and the
temperature field of disc brake under conditions of dynamic speed and
dynamic braking torque was numerically simulated by using ANSYS
software. Finally the distribution and variation laws of temperature
field in the braking process were analyzed. Results indicate that the
maximum surface temperature occurs at a time before the brake end
and there exist large temperature gradients in both radial and axial
directions, while it is relatively small in the circumferential direction.
Abstract: Modeling of complex dynamic systems, which are
very complicated to establish mathematical models, requires new and
modern methodologies that will exploit the existing expert
knowledge, human experience and historical data. Fuzzy cognitive
maps are very suitable, simple, and powerful tools for simulation and
analysis of these kinds of dynamic systems. However, human experts
are subjective and can handle only relatively simple fuzzy cognitive
maps; therefore, there is a need of developing new approaches for an
automated generation of fuzzy cognitive maps using historical data.
In this study, a new learning algorithm, which is called Big Bang-Big
Crunch, is proposed for the first time in literature for an automated
generation of fuzzy cognitive maps from data. Two real-world
examples; namely a process control system and radiation therapy
process, and one synthetic model are used to emphasize the
effectiveness and usefulness of the proposed methodology.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: The paper presents a numerical investigation on the
rapid gas decompression in pure nitrogen which is made by using the
one-dimensional (1D) and three-dimensional (3D) mathematical
models of transient compressible non-isothermal fluid flow in pipes.
A 1D transient mathematical model of compressible thermal multicomponent
fluid mixture flow in pipes is presented. The set of the
mass, momentum and enthalpy conservation equations for gas phase
is solved in the model. Thermo-physical properties of multicomponent
gas mixture are calculated by solving the Equation of
State (EOS) model. The Soave-Redlich-Kwong (SRK-EOS) model is
chosen. This model is successfully validated on the experimental data
[1] and shows a good agreement with measurements. A 3D transient
mathematical model of compressible thermal single-component gas
flow in pipes, which is built by using the CFD Fluent code (ANSYS),
is presented in the paper. The set of unsteady Reynolds-averaged
conservation equations for gas phase is solved. Thermo-physical
properties of single-component gas are calculated by solving the Real
Gas Equation of State (EOS) model. The simplest case of gas
decompression in pure nitrogen is simulated using both 1D and 3D
models. The ability of both models to simulate the process of rapid
decompression with a high order of agreement with each other is
tested. Both, 1D and 3D numerical results show a good agreement
between each other. The numerical investigation shows that 3D CFD
model is very helpful in order to validate 1D simulation results if the
experimental data is absent or limited.
Abstract: Acute toxicity of nano SiO2, ZnO, MCM-41 (Meso
pore silica), Cu, Multi Wall Carbon Nano Tube (MWCNT), Single
Wall Carbon Nano Tube (SWCNT) , Fe (Coated) to bacteria Vibrio
fischeri using a homemade luminometer , was evaluated. The values
of the nominal effective concentrations (EC), causing 20% and 50%
inhibition of biouminescence, using two mathematical models at two
times of 5 and 30 minutes were calculated. Luminometer was
designed with Photomultiplier (PMT) detector. Luminol
chemiluminescence reaction was carried out for the calibration graph.
In the linear calibration range, the correlation coefficients and
coefficient of Variation (CV) were 0.988 and 3.21% respectively
which demonstrate the accuracy and reproducibility of the instrument
that are suitable. The important part of this research depends on how
to optimize the best condition for maximum bioluminescence. The
culture of Vibrio fischeri with optimal conditions in liquid media,
were stirring at 120 rpm at a temperature of 150C to 180C and were
incubated for 24 to 72 hours while solid medium was held at 180C
and for 48 hours. Suspension of nanoparticles ZnO, after 30 min
contact time to bacteria Vibrio fischeri, showed the highest toxicity
while SiO2 nanoparticles showed the lowest toxicity. After 5 min
exposure time, the toxicity of ZnO was the strongest and MCM-41
was the weakest toxicant component.
Abstract: The paper presents a one-dimensional transient
mathematical model of compressible non-isothermal multicomponent
fluid mixture flow in a pipe. The set of the mass,
momentum and enthalpy conservation equations for gas phase is
solved in the model. Thermo-physical properties of multi-component
gas mixture are calculated by solving the Equation of State (EOS)
model. The Soave-Redlich-Kwong (SRK-EOS) model is chosen. Gas
mixture viscosity is calculated on the basis of the Lee-Gonzales-
Eakin (LGE) correlation. Numerical analysis of rapid gas
decompression process in rich and base natural gases is made on the
basis of the proposed mathematical model. The model is successfully
validated on the experimental data [1]. The proposed mathematical
model shows a very good agreement with the experimental data [1] in
a wide range of pressure values and predicts the decompression in
rich and base gas mixtures much better than analytical and
mathematical models, which are available from the open source
literature.
Abstract: In this paper, mathematical models for permutation flow shop scheduling and job shop scheduling problems are proposed. The first problem is based on a mixed integer programming model. As the problem is NP-complete, this model can only be used for smaller instances where an optimal solution can be computed. For large instances, another model is proposed which is suitable for solving the problem by stochastic heuristic methods. For the job shop scheduling problem, a mathematical model and its main representation schemes are presented.
Abstract: This paper examines the use of mechanical aerator for
oxidation-ditch process. The rotor, which controls the aeration, is the
main component of the aeration process. Therefore, the objective of
this study is to find out the variations in overall oxygen transfer
coefficient (KLa) and aeration efficiency (AE) for different
configurations of aerator by varying the parameters viz. speed of
aerator, depth of immersion, blade tip angles so as to yield higher
values of KLa and AE. Six different configurations of aerator were
developed and fabricated in the laboratory and were tested for abovementioned
parameters. The curved blade rotor (CBR) emerged as a
potential aerator with blade tip angle of 47°.
The mathematical models are developed for predicting the
behaviour of CBR w.r.t kLa and power. In laboratory studies, the
optimum value of KLa and AE were observed to be 10.33 h-1 and
2.269 kg O2/ kWh.
Abstract: In this work, we present a reliable framework to solve boundary value problems with particular significance in solid mechanics. These problems are used as mathematical models in deformation of beams. The algorithm rests mainly on a relatively new technique, the Variational Iteration Method. Some examples are given to confirm the efficiency and the accuracy of the method.
Abstract: This article is dedicated to development of
mathematical models for determining the dynamics of
concentration of hazardous substances in urban turbulent
atmosphere. Development of the mathematical models implied
taking into account the time-space variability of the fields of
meteorological items and such turbulent atmosphere data as vortex
nature, nonlinear nature, dissipativity and diffusivity. Knowing the
turbulent airflow velocity is not assumed when developing the
model. However, a simplified model implies that the turbulent and
molecular diffusion ratio is a piecewise constant function that
changes depending on vertical distance from the earth surface.
Thereby an important assumption of vertical stratification of urban
air due to atmospheric accumulation of hazardous substances
emitted by motor vehicles is introduced into the mathematical
model. The suggested simplified non-linear mathematical model of
determining the sought exhaust concentration at a priori unknown
turbulent flow velocity through non-degenerate transformation is
reduced to the model which is subsequently solved analytically.
Abstract: Air conditioning systems of houses consume large
quantity of electricity. To reducing energy consumption for air
conditioning purposes it is becoming attractive the use of evaporative
cooling air conditioning which is less energy consuming compared to
air chillers. But, it is obvious that higher energy efficiency of
evaporative cooling is not enough to judge whether evaporative
cooling economically is competitive with other types of cooling
systems. To proving the higher energy efficiency and cost
effectiveness of the evaporative cooling competitive analysis of
various types of cooling system should be accomplished. For noted
purpose optimization mathematical model for each system should be
composed based on system approach analysis. In this paper different
types of evaporative cooling-heating systems are discussed and
methods for increasing their energy efficiency and as well as
determining of their design parameters are developed. The
optimization mathematical models for each of them are composed
with help of which least specific costs for each of them are reviled.
The comparison of specific costs proved that the most efficient and
cost effective is considered the “direct evaporating" system if it is
applicable for given climatic conditions. Next more universal and
applicable for many climatic conditions system providing least cost
of heating and cooling is considered the “direct evaporating" system.