Abstract: This study deals with evaluation of influence of salinity (NaCl) onto equilibrium of Cu and Ni removal from aqueous solutions by natural sorbent – zeolite. Equilibrium data were obtained by batch experiments. The salinity of the aqueous solution was influenced by dissolving NaCl in distilled water. It was studied in the range of NaCl concentrations from 1 g.l-1 to 100g.l-1. For Cu sorption there is a significant influence of salinity. The maximum capacity of zeolite for Cu was decreasing with growing concentration of NaCl. For Ni sorption there is not so significant influence of salinity as for Cu. The maximum capacity of zeolite for Ni was slightly decreasing with growing concentration of NaCl.
Abstract: This paper demonstrates the bus location system for
the route bus through the experiment in the real environment. A
bus location system is a system that provides information such as
the bus delay and positions. This system uses actual services and
positions data of buses, and those information should match data
on the database. The system has two possible problems. One, the
system could cost high in preparing devices to get bus positions.
Two, it could be difficult to match services data of buses. To avoid
these problems, we have developed this system at low cost and short
time by using the smart phone with GPS and the bus route system.
This system realizes the path planning considering bus delay and
displaying position of buses on the map. The bus location system
was demonstrated on route buses with smart phones for two months.
Abstract: An analysis is performed to study the influence of nonuniform double slot suction on a steady laminar boundary layer flow over a rotating sphere when fluid properties such as viscosity and Prandtl number are inverse linear functions of temperature. Nonsimilar solutions have been obtained from the starting point of the streamwise co-ordinate to the exact point of separation. The difficulties arising at the starting point of the streamwise co-ordinate, at the edges of the slot and at the point of separation have been overcome by applying an implicit finite difference scheme in combination with the quasi-linearization technique and an appropriate selection of the finer step sizes along the stream-wise direction. The present investigation shows that the point of ordinary separation can be delayed by nonuniform double slot suction if the mass transfer rate is increased and also if the slots are positioned further downstream. In addition, the investigation reveals that double slot suction is found to be more effective compared to a single slot suction in delaying ordinary separation. As rotation parameter increase the point of separation moves upstream direction.
Abstract: Algae-based fuel are considered a promising sources
of clean energy, and because it has many advantages over traditional
biofuel, research and business ventures have driven into developing
and producing Algal-biofuel. But its production stages create a cost
structure that it is not competitive with traditional fuels. Therefore,
cost becomes the main obstacle in commercial production purpose.
However, the present research which aims at using cost structure
model, and designed MS-Dose program, to investigate the a mount of
production cost and determined the parameter had great effect on it,
second to measured the amount of contribution rate of algae in
process the pollution by capturing Co2 from air . The result generated
from the model shows that the production cost of biomass is between
$0.137 /kg for 100 ha and $0.132 /kg for 500 ha which was less than
cost of other studies, while gallon costs between $3.4 - 3.5, more
than traditional sources of oil about $1 ,which regarded as a rate of
contribution of algal in capturing CO2 from air.
Abstract: Modelling techniques for a fluid coupling taken from
published literature have been extended to include the effects of the
filling and emptying of the coupling with oil and the variation in
losses when the coupling is partially full. In the model, the fluid flow
inside the coupling is considered to have two principal velocity
components; one circumferentially about the coupling axis
(centrifugal head) and the other representing the secondary vortex
within the coupling itself (vortex head). The calculation of liquid
mass flow rate circulating between the two halves of the coupling is
based on: the assumption of a linear velocity variation in the
circulating vortex flow; the head differential in the fluid due to the
speed difference between the two shafts; and the losses in the
circulating vortex flow as a result of the impingement of the flow
with the blades in the coupling and friction within the passages
between the blades.
Abstract: The performance and the plasma created by a pulsed
magnetoplasmadynamic thruster for small satellite application is
studied to understand better the ablation and plasma propagation
processes occurring during the short-time discharge. The results can
be applied to improve the quality of the thruster in terms of efficiency,
and to tune the propulsion system to the needs required by the satellite
mission. Therefore, plasma measurements with a high-speed camera
and induction probes, and performance measurements of mass bit
and impulse bit were conducted. Values for current sheet propagation
speed, mean exhaust velocity and thrust efficiency were derived from
these experimental data. A maximum in current sheet propagation
was found by the high-speed camera measurements for a medium
energy input and confirmed by the induction probes. A quasilinear
tendency between the mass bit and the energy input, the current
action integral respectively, was found, as well as a linear tendency
between the created impulse and the discharge energy. The highest
mean exhaust velocity and thrust efficiency was found for the highest
energy input.
Abstract: Group-III nitride material as particularly AlxGa1-xN is
one of promising optoelectronic materials to require for shortwavelength
devices. To achieve the high-quality AlxGa1-xN films for
a high performance of such devices, AlN-nucleation layers are the
important factor. To improve the AlN-nucleation layers with a
variation of Ga-addition, XRD measurements were conducted to
analyze the crystalline quality of the subsequent Al0.1Ga0.9N with the
minimum ω-FWHMs of (0002) and (10-10) reflections of 425 arcsec
and 750 arcsec, respectively. SEM and AFM measurements were
performed to observe the surface morphology and TEM
measurements to identify the microstructures and orientations.
Results showed that the optimized Ga-atoms in the Al(Ga)Nnucleation
layers improved the surface diffusion to form moreuniform
crystallites in structure and size, better alignment of each
crystallite, and better homogeneity of island distribution. This, hence,
improves the orientation of epilayers on the Si-surface and finally
improves the crystalline quality and reduces the residual strain of
subsequent Al0.1Ga0.9N layers.
Abstract: The objective of this research is to study of microbial lipid production by locally photosynthetic microalgae and oleaginous yeast via integrated cultivation technique using CO2 emissions from yeast fermentation. A maximum specific growth rate of Chlorella sp. KKU-S2 of 0.284 (1/d) was obtained under an integrated cultivation and a maximum lipid yield of 1.339g/L was found after cultivation for 5 days, while 0.969g/L of lipid yield was obtained after day 6 of cultivation time by using CO2 from air. A high value of volumetric lipid production rate (QP, 0.223 g/L/d), specific product yield (YP/X, 0.194), volumetric cell mass production rate (QX, 1.153 g/L/d) were found by using ambient air CO2 coupled with CO2 emissions from yeast fermentation. Overall lipid yield of 8.33 g/L was obtained (1.339 g/L of Chlorella sp. KKU-S2 and 7.06g/L of T. maleeae Y30) while low lipid yield of 0.969g/L was found using non-integrated cultivation technique. To our knowledge this is the unique report about the lipid production from locally microalgae Chlorella sp. KKU-S2 and yeast T. maleeae Y30 in an integrated technique to improve the biomass and lipid yield by using CO2 emissions from yeast fermentation.
Abstract: Clustering in high dimensional space is a difficult
problem which is recurrent in many fields of science and
engineering, e.g., bioinformatics, image processing, pattern
reorganization and data mining. In high dimensional space some of
the dimensions are likely to be irrelevant, thus hiding the possible
clustering. In very high dimensions it is common for all the objects in
a dataset to be nearly equidistant from each other, completely
masking the clusters. Hence, performance of the clustering algorithm
decreases.
In this paper, we propose an algorithmic framework which
combines the (reduct) concept of rough set theory with the k-means
algorithm to remove the irrelevant dimensions in a high dimensional
space and obtain appropriate clusters. Our experiment on test data
shows that this framework increases efficiency of the clustering
process and accuracy of the results.
Abstract: The study of a real function of two real variables can be supported by visualization using a Computer Algebra System (CAS). One type of constraints of the system is due to the algorithms implemented, yielding continuous approximations of the given function by interpolation. This often masks discontinuities of the function and can provide strange plots, not compatible with the mathematics. In recent years, point based geometry has gained increasing attention as an alternative surface representation, both for efficient rendering and for flexible geometry processing of complex surfaces. In this paper we present different artifacts created by mesh surfaces near discontinuities and propose a point based method that controls and reduces these artifacts. A least squares penalty method for an automatic generation of the mesh that controls the behavior of the chosen function is presented. The special feature of this method is the ability to improve the accuracy of the surface visualization near a set of interior points where the function may be discontinuous. The present method is formulated as a minimax problem and the non uniform mesh is generated using an iterative algorithm. Results show that for large poorly conditioned matrices, the new algorithm gives more accurate results than the classical preconditioned conjugate algorithm.
Abstract: Based on Rayleigh beam theory, the sub-impacts of a
free-free beam struck horizontally by a round-nosed rigid mass is
simulated by the finite difference method and the impact-separation
conditions. In order to obtain the sub-impact force, a uniaxial
compression elastic-plastic contact model is employed to analyze the
local deformation field on contact zone. It is found that the horizontal
impact is a complicated process including the elastic plastic
sub-impacts in sequence. There are two sub-zones of sub-impact. In
addition, it found that the elastic energy of the free-free beam is more
suitable for the Poisson collision hypothesis to explain compression
and recovery processes.
Abstract: The Inter feeder Power Flow Regulator (IFPFR)
proposed in this paper consists of several voltage source inverters
with common dc bus; each inverter is connected in series with one of
different independent distribution feeders in the power system. This
paper is concerned with how to transfer power between the feeders for
load sharing purpose. The power controller of each inverter injects
the power (for sending feeder) or absorbs the power (for receiving
feeder) via injecting suitable voltage; this voltage injection is
simulated by voltage drop across series virtual impedance, the
impedance value is selected to achieve the concept of power exchange
between the feeders without perturbing the load voltage magnitude of
each feeder. In this paper a new control scheme for load sharing using
IFPFR is proposed.
Abstract: The equilibrium, thermodynamics and kinetics of the
biosorption of Cd (II) and Pb(II) by a Spore Forming Bacillus (MGL
75) were investigated at different experimental conditions. The
Langmuir and Freundlich, and Dubinin-Radushkevich (D-R)
equilibrium adsorption models were applied to describe the
biosorption of the metal ions by MGL 75 biomass. The Langmuir
model fitted the equilibrium data better than the other models.
Maximum adsorption capacities q max for lead (II) and cadmium (II)
were found equal to 158.73mg/g and 91.74 mg/g by Langmuir model.
The values of the mean free energy determined with the D-R equation
showed that adsorption process is a physiosorption process. The
thermodynamic parameters Gibbs free energy (ΔG°), enthalpy (ΔH°),
and entropy (ΔS°) changes were also calculated, and the values
indicated that the biosorption process was exothermic and
spontaneous. Experiment data were also used to study biosorption
kinetics using pseudo-first-order and pseudo-second-order kinetic
models. Kinetic parameters, rate constants, equilibrium sorption
capacities and related correlation coefficients were calculated and
discussed. The results showed that the biosorption processes of both
metal ions followed well pseudo-second-order kinetics.
Abstract: The Niger Delta Region of Nigeria is home to about
20 million people and 40 different ethnic groups. The region has an
area of seventy thousand square kilometers (70,000 KM2) of
wetlands, formed primarily by sediments deposition and makes up
7.5 percent of Nigeria's total landmass. The notable ecological zones
in this region includes: coastal barrier islands; mangrove swamp
forests; fresh water swamps; and lowland rainforests. This incredibly
naturally-endowed ecosystem region, which contains one of the
highest concentrations of biodiversity on the planet, in addition to
supporting abundant flora and fauna, is threatened by the inhuman act
known as gas flaring. Gas flaring is the combustion of natural gas
that is associated with crude oil when it is pumped up from the
ground. In petroleum-producing areas such as the Niger Delta region
of Nigeria where insufficient investment was made in infrastructure
to utilize natural gas, flaring is employed to dispose of this associated
gas. This practice has impoverished the communities where it is
practiced, with attendant environmental, economic and health
challenges. This paper discusses the adverse environmental and
health implication associated with the practice, the role of
Government, Policy makers, Oil companies and the Local
communities aimed at bring this inhuman practice to a prompt end.
Abstract: This paper features the modeling and design of a Fast
Output Sampling (FOS) Feedback control technique for the Active
Vibration Control (AVC) of a smart flexible aluminium cantilever
beam for a Single Input Single Output (SISO) case. Controllers are
designed for the beam by bonding patches of piezoelectric layer as
sensor / actuator to the master structure at different locations along
the length of the beam by retaining the first 2 dominant vibratory
modes. The entire structure is modeled in state space form using the
concept of piezoelectric theory, Euler-Bernoulli beam theory, Finite
Element Method (FEM) and the state space techniques by dividing
the structure into 3, 4, 5 finite elements, thus giving rise to three
types of systems, viz., system 1 (beam divided into 3 finite
elements), system 2 (4 finite elements), system 3 (5 finite elements).
The effect of placing the sensor / actuator at various locations along
the length of the beam for all the 3 types of systems considered is
observed and the conclusions are drawn for the best performance and
for the smallest magnitude of the control input required to control the
vibrations of the beam. Simulations are performed in MATLAB. The
open loop responses, closed loop responses and the tip displacements
with and without the controller are obtained and the performance of
the proposed smart system is evaluated for vibration control.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: Xanthan gum is a microbial polysaccharide of great
commercial significance. The purpose of this study was to select the
optimum fermentation time for xanthan gum production by
Xanthomonas campestris (NRRL-B-1459) using 10% sugar beet
molasses as a carbon source. The pre-heating of sugar beet molasses
and the supplementation of the medium were investigated in order to
improve xanthan gum production. Maximum xanthan gum
production in fermentation media (9.02 g/l) was observed after 4 days
shaking incubation at 25°C and 240 rpm agitation speed. A solution
of 10% sucrose was used as a control medium. Results indicated that
the optimum period for xanthan gum production in this condition was
4 days.
Abstract: Aptamers are useful tools in microorganism
researches, diagnoses, and treatment. Aptamers are specific target
molecules formed by oligonucleic acid molecules, and are not
decomposed by alcohol. Aptamers used to detect Mycobacterium
tuberculosis (MTB) have been proved to have specific affinity to the
outer membrane proteins of MTB. This article presents a biosensor
chip set with aptamers for early detection of MTB with high specificity
and sensitivity, even in very low concentration. Meanwhile, we have
already made a modified hydrophobic facial mask module with
internal rendering hydrophobic for effectively collecting M.
tuberculosis.
Abstract: This paper presents a new sensor-based online method for generating collision-free near-optimal paths for mobile robots pursuing a moving target amidst dynamic and static obstacles. At each iteration, first the set of all collision-free directions are calculated using velocity vectors of the robot relative to each obstacle and target, forming the Directive Circle (DC), which is a novel concept. Then, a direction close to the shortest path to the target is selected from feasible directions in DC. The DC prevents the robot from being trapped in deadlocks or local minima. It is assumed that the target's velocity is known, while the speeds of dynamic obstacles, as well as the locations of static obstacles, are to be calculated online. Extensive simulations and experimental results demonstrated the efficiency of the proposed method and its success in coping with complex environments and obstacles.
Abstract: Fructooligosaccharides derived from microbial enzyme especially from fungal sources has been received particular attention due to its beneficial effects as prebiotics and mass production. However, fungal fermentation is always cumbersome due to its broth rheology problem that will eventually affect the production of FOS. This study investigated the efficiency of immobilized cell system using rotating fibrous bed bioreactor (RFBB) in producing fructooligosaccharides (FOS). A comparative picture with respect to conventional stirred tank bioreactor (CSTB) and RFBB has been presented. To demonstrate the effect of agitation intensity and aeration rate, a laboratory-scale bioreactor 2.5 L was operated in three phases (high, medium, low) for 48 hours. Agitation speed has a great influence on P. simplicissimum fermentation for FOS production, where the volumetric FOS productivity using RFBB is increased with almost 4 fold compared to the FOS productivity in CSTB that only 0.319 g/L/h. Rate of FOS production increased up to 1.2 fold when immobilized cells system was employed at aeration rate similar to the freely suspended cells at 2.0 vvm.