Abstract: In this study, we proposed two techniques to track the
maximum power point (MPPT) of a photovoltaic system. The first is
an intelligent control technique, and the second is robust used for
variable structure system. In fact the characteristics I-V and P–V of
the photovoltaic generator depends on the solar irradiance and
temperature. These climate changes cause the fluctuation of
maximum power point; a maximum power point tracking technique
(MPPT) is required to maximize the output power. For this we have
adopted a control by fuzzy logic (FLC) famous for its stability and
robustness. And a Siding Mode Control (SMC) widely used for
variable structure system. The system comprises a photovoltaic panel
(PV), a DC-DC converter, which is considered as an adaptation stage
between the PV and the load. The modelling and simulation of the
system is developed using MATLAB/Simulink. SMC technique
provides a good tracking speed in fast changing irradiation and when
the irradiation changes slowly or it is constant the panel power of
FLC technique presents a much smoother signal with less
fluctuations.
Abstract: Transmission shafts are affected by various forces, for
example, during acceleration or sudden breaks, bending during
transportation, vertical forces that lead to cuts. One of the main
failures in combines is breaking shaft which repairmen refer it.
Structural resistance of canal against torque is very important in the
beginning of the movement. For analyzing stress, a typical sample
from a type of combine was selected, called JD955 combine. Long
shaft in this combine was analyzed with finite element method by
Ansys13 generic package under static load. Conducted analysis
showed that there is a maximum stress in contact surfaces of
indentations and also in place of changing diameter. Safety factor
value is low in parts of the shaft and this increases the probability of
failure at these points. To improve the conditions with the least cost
and an approach of product improvement, using alternative alloy is
important.
Abstract: In this paper, a direct power control (DPC)
strategies have been investigated in order to control a high
power AC/DC converter with time variable load. This converter
is composed of a three level three phase neutral point clamped
(NPC) converter as rectifier and an H-bridge four quadrant
current control converter. In the high power application,
controller not only must adjust the desire outputs but also
decrease the level of distortions which are injected to the network
from the converter. Regarding to this reason and nonlinearity
of the power electronic converter, the conventional controllers
cannot achieve appropriate responses. In this research, the
precise mathematical analysis has been employed to design the
appropriate controller in order to control the time variable
load. A DPC controller has been proposed and simulated using
Matlab/ Simulink. In order to verify the simulation result, a real
time simulator- OPAL-RT- has been employed. In this paper,
the dynamic response and stability of the high power NPC
with variable load has been investigated and compared with
conventional types using a real time simulator. The results proved
that the DPC controller is more stable and has more precise
outputs in comparison with conventional controller.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. This paper describes experimental
investigation on the response of new advanced materials to low and
high velocity load. Blast wave energy absorbers were designed using
two types of porous lightweight raw particle materials based on
expanded glass and ceramics with dimensions of 0.5-1 mm,
combined with polymeric binder. The effect of binder amount on the
static and dynamic properties of designed materials was observed.
Prism shaped specimens were prepared and loaded to obtain physicomechanical
parameters – bulk density, compressive and flexural
strength under quasistatic load, the dynamic response was determined
using Split Hopkinson Pressure bar apparatus. Numerical
investigation of the material behaviour in sandwich structure was
performed using implicit/explicit solver LS-Dyna. As the last step,
the developed material was used as the interlayer of blast resistant
litter bin, and it´s functionality was verified by real field blast tests.
Abstract: Power Regeneration in Refrigeration Plant concept
has been analyzed and has been shown to be capable of saving about
25% power in Cryogenic Plants with the Power Regeneration System
(PRS) running under nominal conditions. The innovative component
Compressor Expander Group (CEG) based on turbomachinery has
been designed and built modifying CETT compressor and expander,
both selected for optimum plant performance. Experiments have
shown the good response of the turbomachines to run with R404a as
working fluid. Power saving up to 12% under PRS derated conditions
(50% loading) has been demonstrated. Such experiments allowed
predicting a power saving up to 25% under CEG full load.
Abstract: This paper discusses the design and analysis of a
hybrid PV-Fuel cell energy system destined to power a DC load. The
system is composed of a photovoltaic array, a fuel cell, an
electrolyzer and a hydrogen tank. HOMER software is used in this
study to calculate the optimum capacities of the power system
components that their combination allows an efficient use of solar
resource to cover the hourly load needs. The optimal system sizing
allows establishing the right balance between the daily electrical
energy produced by the power system and the daily electrical energy
consumed by the DC load using a 28 KW PV array, a 7.5 KW fuel
cell, a 40KW electrolyzer and a 270 Kg hydrogen tank. The variation
of powers involved into the DC bus of the hybrid PV-fuel cell system
has been computed and analyzed for each hour over one year: the
output powers of the PV array and the fuel cell, the input power of
the elctrolyzer system and the DC primary load. Equally, the annual
variation of stored hydrogen produced by the electrolyzer has been
assessed. The PV array contributes in the power system with 82%
whereas the fuel cell produces 18%. 38% of the total energy
consumption belongs to the DC primary load while the rest goes to
the electrolyzer.
Abstract: In this paper we are presenting some spamming
techniques their behaviour and possible solutions. We have analyzed
how Spammers enters into online social networking sites (OSNSs) to
target them and diverse techniques used by them for this purpose.
Spamming is very common issue in present era of Internet
especially through Online Social Networking Sites (like Facebook,
Twitter, and Google+ etc.). Spam messages keep wasting Internet
bandwidth and the storage space of servers. On social networking
sites; spammers often disguise themselves by creating fake accounts
and hijacking user’s accounts for personal gains. They behave like
normal user and they continue to change their spamming strategy.
Following spamming techniques are discussed in this paper like
clickjacking, social engineered attacks, cross site scripting, URL
shortening, and drive by download. We have used elgg framework
for demonstration of some of spamming threats and respective
implementation of solutions.
Abstract: Power systems are operating under stressed condition
due to continuous increase in demand of load. This can lead to
voltage instability problem when face additional load increase or
contingency. In order to avoid voltage instability suitable size of
reactive power compensation at optimal location in the system is
required which improves the load margin. This work aims at
obtaining optimal size as well as location of compensation in the 39-
bus New England system with the help of Bacteria Foraging and
Genetic algorithms. To reduce the computational time the work
identifies weak candidate buses in the system, and then picks only
two of them to take part in the optimization. The objective function is
based on a recently proposed voltage stability index which takes into
account the weighted average sensitivity index is a simpler and faster
approach than the conventional CPF algorithm. BFOA has been
found to give better results compared to GA.
Abstract: The paper presents a practical three-phase PWM
inverter suitable for low voltage, low rating energy efficient systems.
The work in the paper is conducted with the view to establishing the
significance of the loss contribution from the PWM inverter in the
determination of the complete losses of a photovoltaic (PV) arraypowered
induction motor drive water pumping system. Losses
investigated include; conduction and switching loss of the devices
and gate drive losses. It is found that the PWM inverter operates at a
reasonable variable efficiency that does not fall below 92%
depending on the load. The results between the simulated and
experimental results for the system with or without a maximum
power tracker (MPT) compares very well, within an acceptable range
of 2% margin.
Abstract: Wind energy offers a significant advantage such as no
fuel costs and no emissions from generation. However, wind energy
sources are variable and non-dispatchable. The utility grid is able to
accommodate the variability of wind in smaller proportion along with
the daily load. However, at high penetration levels, the variability can
severely impact the utility reserve requirements and the cost
associated with it. In this paper the impact of wind energy is
evaluated in detail in formulating the total utility cost. The objective
is to minimize the overall cost of generation while ensuring the
proper management of the load. Overall cost includes the curtailment
cost, reserve cost and the reliability cost, as well as any other penalty
imposed by the regulatory authority. Different levels of wind
penetrations are explored and the cost impacts are evaluated. As the
penetration level increases significantly, the reliability becomes a
critical question to be answered. Here we increase the penetration
from the wind yet keep the reliability factor within the acceptable
limit provided by NERC. This paper uses an economic dispatch (ED)
model to incorporate wind generation into the power grid. Power
system costs are analyzed at various wind penetration levels using
Linear Programming. The goal of this study is show how the
increases in wind generation will affect power system economics.
Abstract: In rapid industrial development, the demand for
high-strength and lightweight materials have been increased. Thus,
various CFRP (Carbon Fiber Reinforced Plastics) with composite
materials are being used. The design variables of CFRP are its
lamination direction, order and thickness. Thus, the hardness and
strength of CFRP depends much on their design variables. In this
paper, the lamination direction of CFRP was used to produce a
symmetrical ply [0°/0°, -15°/+15°, -30°/+30°, -45°/+45°, -60°/+60°,
-75°/+75° and 90°/90°] and an asymmetrical ply [0°/15°, 0°/30°,
0°/45°, 0°/60° 0°/75° and 0°/90°]. The bending flexure stress of the
CFRP specimen was evaluated through a bending test. Its thermal
property was measured using an infrared camera. The symmetrical
specimen and the asymmetrical specimen were analyzed. The results
showed that the asymmetrical specimen increased the bending loads
according to the increase in the orientation angle; and from 0°, the
symmetrical specimen showed a tendency opposite the asymmetrical
tendency because the tensile force of fiber differs at the vertical
direction of its load. Also, the infrared camera showed that the thermal
property had a trend similar to that of the mechanical properties.
Abstract: Collection of storm water runoff and forcing it into the
groundwater is the need of the hour to sustain the ground water table.
However, the runoff entraps various types of sediments and other
floating objects whose removal are essential to avoid pollution of
ground water and blocking of pores of aquifer. However, it requires
regular cleaning and maintenance due to problem of clogging. To
evaluate the performance of filter system consisting of coarse sand
(CS), gravel (G) and pebble (P) layers, a laboratory experiment was
conducted in a rectangular column. The effect of variable thickness
of CS, G and P layers of the filtration unit of the recharge shaft on the
recharge rate and the sediment concentration of effluent water were
evaluated.
Medium sand (MS) of three particle sizes, viz. 0.150–0.300 mm
(T1), 0.300–0.425 mm (T2) and 0.425–0.600 mm of thickness 25 cm,
30 cm and 35 cm respectively in the top layer of the filter system and
having seven influent sediment concentrations of 250–3,000 mg/l
were used for experimental study. The performance was evaluated in
terms of recharge rates and clogging time. The results indicated that
100 % suspended solids were entrapped in the upper 10 cm layer of
MS, the recharge rates declined sharply for influent concentrations of
more than 1,000 mg/l. All treatments with higher thickness of MS
media indicated recharge rate slightly more than that of all treatment
with lower thickness of MS media respectively. The performance of
storm water infiltration systems was highly dependent on the
formation of a clogging layer at the filter. An empirical relationship
has been derived between recharge rates, inflow sediment load, size
of MS and thickness of MS with using MLR.
Abstract: Load modeling is one of the central functions in
power systems operations. Electricity cannot be stored, which means
that for electric utility, the estimate of the future demand is necessary
in managing the production and purchasing in an economically
reasonable way. A majority of the recently reported approaches are
based on neural network. The attraction of the methods lies in the
assumption that neural networks are able to learn properties of the
load. However, the development of the methods is not finished, and
the lack of comparative results on different model variations is a
problem. This paper presents a new approach in order to predict the
Tunisia daily peak load. The proposed method employs a
computational intelligence scheme based on the Fuzzy neural
network (FNN) and support vector regression (SVR). Experimental
results obtained indicate that our proposed FNN-SVR technique gives
significantly good prediction accuracy compared to some classical
techniques.
Abstract: There are a variety of reference current identification
methods, for the shunt active power filter (SAPF), such as the
instantaneous active and reactive power, the instantaneous active and
reactive current and the synchronous detection method are evaluated
and compared under ideal, non sinusoidal and unbalanced voltage
conditions. The SAPF performances, for the investigated
identification methods, are tested for a non linear load. The
simulation results, using Matlab Power System Blockset Toolbox
from a complete structure, are presented and discussed.
Abstract: The power converter that feeds high-frequency, highvoltage
transformers must be carefully designed due to parasitic
components, mainly the secondary winding capacitance and the
leakage inductance, that introduces resonances in relatively lowfrequency
range, next to the switching frequency. This paper
considers applications in which the load (resistive) has an
unpredictable behavior, changing from open to short-circuit condition
faster than the output voltage control loop could react. In this context,
to avoid overvoltage and over current situations, that could damage
the converter, the transformer or the load, it is necessary to find an
operation point that assure the desired output voltage in spite of the
load condition. This can done adjusting the frequency response of the
transformer adding an external inductance, together with selecting the
switching frequency to get stable output voltage independently of the
load.
Abstract: Weed suppression and weeding are necessary measures
for rice cultivation. Weed suppression precedes the process of
weeding. It means suppressing the growth of young weeds and
creating a weed-less environment. If we suppress the growth of weeds,
we can reduce the number of weeds in a paddy field. This would result
in a reduction of the weeding work load.
In this paper, we will show how we developed a weed suppression
robot for the purpose of reducing the weeding work load. The robot
has a laser range finder for autonomous mobility and a robot arm for
weed suppression. It travels along the rice rows without stepping on
and injuring the rice plants in a paddy field. The robot arm applies
force to the weed seedlings and thereby suppresses the growth of
weeds. This paper will explain the methodology of the autonomous
mobile, the experiment in weed suppression, and the method of
controlling the robot’s posture on uneven ground.
Abstract: An investigation into the effect of countersunk depth,
plate thickness, countersunk angle and plate width on the stress
concentration around countersunk hole is carried out with the help of
finite element analysis. The variation of stress concentration with
respect to these parameters is studied for three types of loading viz.
uniformly distributed load, uniformly varying load and functionally
distributed load. The results of the finite element analysis are
interpreted and some conclusions are drawn. The distribution of
stress concentration around countersunk hole in isotropic plates
simply supported at all the edges is found similar and is independent
of loading. The maximum stress concentration also occurs at a
particular point irrespective of the loading conditions.
Abstract: Recently, there have been a lot of earthquakes in Japan.
It is necessary to promote seismic isolation devices for buildings. The
devices have been hardly diffused in attached houses, because the
devices are very expensive. We should develop a low-cost seismic
isolation device for detached houses. We suggested a new seismic
isolation device which uses a two-layer circular tube as a unit. If
hysteresis is produced in the two-layer circular tube under lateral
compression load, we think that the two-layer circular tube can have
energy absorbing capacity. It is necessary to contact the outer layer
and the inner layer to produce hysteresis. We have previously reported
how the inner layer comes in contact with the outer layer from a
perspective of analysis used mechanics of materials. We have clarified
that the inner layer comes in contact with the outer layer under a lateral
compression load. In this paper, we explored contact area between the
outer layer and the inner layer under a lateral compression load by
using FEA. We think that changing the inner layer’s thickness is
effective in increase the contact area. In order to change the inner
layer’s thickness, we changed the shape of the inner layer. As a result,
the contact area changes depending on the inner layer’s thickness.
Additionally, we experimented to check whether hysteresis occurs in
fact. As a consequence, we can reveal hysteresis in the two-layer
circular tube under the condition.
Abstract: This paper presents the variation of the dynamic
characteristics of a spindle with the change of bearing preload. The
correlations between the variation of bearing preload and fundamental
modal parameters were first examined by conducting vibration tests on
physical spindle units. Experimental measurements show that the
dynamic compliance and damping ratio associated with the
dominating modes were affected to vary with variation of the bearing
preload. When the bearing preload was slightly deviated from a
standard value, the modal frequency and damping ability also vary to
different extent, which further enable the spindle to perform with
different compliance. For the spindle used in this study, a standard
preload value set on bearings would enable the spindle to behave a
higher stiffness as compared with others with a preload variation. This
characteristic can be served as a reference to examine the variation of
bearing preload of spindle in assemblage or operation.
Abstract: The use of biodiesel in conventional diesel engines results in substantial reduction of unburned hydrocarbon, carbon monoxide and particulate matters. The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio engine when fueled with Karanja (Pongamia) methyl ester and its 10-50 % blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of karanja methyl ester as a biofuel has been established in this study. The useful brake power obtained is similar to diesel fuel for all loads. Experiment has been conducted at a fixed engine speed of 1500 rpm, variable load and at compression ratios of 17.5:1 and 18.5:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for pongamia oil methyl ester when compared to that of diesel. The brake thermal efficiency for pongamia oil methyl ester blends and diesel has been calculated and the blend B20 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions. PME as an oxygenated fuel generated more complete combustion, which means increased torque and power. This is also supported with higher thermal efficiencies of the PME blends. NOx is slightly increased due to the higher combustion temperature and the presence of fuel oxygen with the blend at full load. PME as a new Biodiesel and its blends can be used in diesel engines without any engine modification.