Abstract: Headphones and earphones have many extremely small
holes or narrow slits; they use sound-absorbing or porous material (i.e.,
dampers) to suppress vibratory system resonance. The air viscosity in
these acoustic paths greatly affects the acoustic properties. Simulation
analyses such as the finite element method (FEM) therefore require
knowledge of the material properties of sound-absorbing or porous
materials, such as the characteristic impedance and propagation
constant. The transfer function method using acoustic tubes is a widely
known measuring method, but there is no literature on taking
measurements up to the audible range. To measure the acoustic
properties at high-range frequencies, the acoustic tubes that form the
measuring device need to be narrowed, and the distance between the
two microphones needs to be reduced. However, when the tubes are
narrowed, the characteristic impedance drops below the air impedance.
In this study, we considered the effect of air viscosity in an acoustical
tube, introduced a theoretical formula for this effect in the form of
complex density and complex sonic velocity, and verified the
theoretical formula. We also conducted an experiment and observed
the effect from air viscosity in the actual measurements.
Abstract: One of the most important power quality issues is voltage flicker. Nowadays this issue also impacts the power system all over the world. The fact of the matter is that the more and the larger capacity of wind generator has been installed. Under unstable wind power situation, the variation of output current and voltage have caused trouble to voltage flicker. Hence, the major purpose of this study is to analyze the impact of wind generator on voltage flicker of power system. First of all, digital simulation and analysis are carried out based on wind generator operating under various system short circuit capacity, impedance angle, loading, and power factor of load. The simulation results have been confirmed by field measurements.
Abstract: In this paper a computer system for electromagnetic
properties measurements is designed. The system employs Agilent
4294A precision impedance analyzer to measure the amplitude and
the phase of a signal applied over a tested biological tissue sample.
Measured by the developed computer system data could be used for
tissue characterization in wide frequency range from 40Hz to
110MHz. The computer system can interface with output devices
acquiring flexible testing process.
Abstract: Nonlinear and unbalance loads in three phase
networks create harmonics and losses. Active and passive filters are
used for elimination or reduction of these effects. Passive filters have
some limitations. For example, they are designed only for a specific
frequency and they may cause to resonance in the network at the
point of common coupling. The other drawback of a passive filter is
that the sizes of required elements are normally large. The active
filter can improve some of limitations of passive filter for example;
they can eliminate more than one harmonic and don't cause resonance
in the network. In this paper inverter analysis have been done
simultaneously in three phase and the RL impedance of the line have
been considered. A sliding mode control based on energy feedback of
capacitors is employed in the design with this method, the dynamic
speed of the filter is improved effectively and harmonics and load
unbalance is compensating quickly.
Abstract: This paper presents a simple approach for load
flow analysis of a radial distribution network. The proposed
approach utilizes forward and backward sweep algorithm
based on Kirchoff-s current law (KCL) and Kirchoff-s voltage
law (KVL) for evaluating the node voltages iteratively. In this
approach, computation of branch current depends only on the
current injected at the neighbouring node and the current in
the adjacent branch. This approach starts from the end nodes
of sub lateral line, lateral line and main line and moves
towards the root node during branch current computation. The
node voltage evaluation begins from the root node and moves
towards the nodes located at the far end of the main, lateral
and sub lateral lines. The proposed approach has been tested
using four radial distribution systems of different size and
configuration and found to be computationally efficient.
Abstract: The passive electrical properties of a tissue depends
on the intrinsic constituents and its structure, therefore by measuring
the complex electrical impedance of the tissue it might be possible to
obtain indicators of the tissue state or physiological activity [1].
Complete bio-impedance information relative to physiology and
pathology of a human body and functional states of the body tissue or
organs can be extracted by using a technique containing a fourelectrode
measurement setup. This work presents the estimation
measurement setup based on the four-electrode technique. First, the
complex impedance is estimated by three different estimation
techniques: Fourier, Sine Correlation and Digital De-convolution and
then estimation errors for the magnitude, phase, reactance and
resistance are calculated and analyzed for different levels of
disturbances in the observations. The absolute values of relative
errors are plotted and the graphical performance of each technique is
compared.
Abstract: The High Voltage (HV) transmission mains into the community necessitate earthing design to ensure safety compliance of the system. Concrete poles are widely used within HV transmission mains; which could have an impact on the earth grid impedance and input impedance of the system from the fault point of view. This paper provides information on concrete pole earthing to enhance the split factor of the system; further, it discusses the deployment of concrete structures in high soil resistivity area to reduce the earth grid system of the plant. This paper introduces the cut off soil resistivity SC ρ when replacing timber poles with concrete ones.
Abstract: For investigations of electromagnetic field
distributions in biological structures by Finite Element Method
(FEM), a method for automatic 3D model building of human
anatomical objects is developed. Models are made by meshed
structures and specific electromagnetic material properties for each
tissue type. Mesh is built according to specific FEM criteria for
achieving good solution accuracy. Several FEM models of
anatomical objects are built. Formulation using magnetic vector
potential and scalar electric potential (A-V, A) is used for modeling
of electromagnetic fields in human tissue objects. The developed
models are suitable for investigations of electromagnetic field
distributions in human tissues exposed in external fields during
magnetic stimulation, defibrillation, impedance tomography etc.
Abstract: The increasing demand for higher data rates in wireless communication systems has led to the more effective and efficient use of all allocated frequency bands. In order to use the whole bandwidth at maximum efficiency, one needs to have RF power amplifiers with a higher linear level and memory-less performance. This is considered to be a major challenge to circuit designers. In this thesis the linearity and memory are studied and examined via the behavior of the intermodulation distortion (IMD). A major source of the in-band distortion can be shown to be influenced by the out-of-band impedances presented at either the input or the output of the device, especially those impedances terminated the low frequency (IF) components. Thus, in order to regulate the in-band distortion, the out of-band distortion must be controllable. These investigations are performed on a 12W LDMOS device characterised at 2.1 GHz within a purpose built, high-power measurement system.
Abstract: In this paper, a planar antenna for UWB applications
has been proposed. The antenna consists of a square patch, a partial
ground plane and a slot on the ground plane. The proposed antenna is
easy to be integrated with microwave circuitry for low manufacturing
cost. The flat type antenna has a compact structure and the total size
is 14.5×14.5mm2. The result shows that the impedance bandwidth
(VSWR≤ 2) of the proposed antenna is 12.49 GHz (2.95 to 15.44
GHz), which is equivalent to 135.8%. Details of the proposed
compact planar UWB antenna design is presented and discussed.
Abstract: Langmuir–Blodgett (LB) films of polyaniline (PANI) grown onto ITO coated glass substrates were utilized for the fabrication of Uric acid biosensor for efficient detection of uric acid by immobilizing Uricase via EDC–NHS coupling. The modified electrodes were characterized by atomic force microscopy (AFM). The response characteristics after immobilization of uricase were studied using cyclic voltammetry and electrochemical impedance spectroscopy techniques. The uricase/PANI/ITO/glass bioelectrode studied by CV and EIS techniques revealed detection of uric acid in a wide range of 0.05 mM to 1.0 mM, covering the physiological range in blood. A low Michaelis–Menten constant (Km) of 0.21 mM indicates the higher affinity of immobilized Uricase towards its analyte (uric acid). The fabricated uric acid biosensor based on PANI LB films exhibits excellent sensitivity of 0.21 mA/mM with a response time of 4 s, good reproducibility, long shelf life (8 weeks) and high selectivity.
Abstract: Electric impedance imaging is a method of
reconstructing spatial distribution of electrical conductivity inside a
subject. In this paper, a new method of electrical impedance imaging
using eddy current is proposed. The eddy current distribution in the
body depends on the conductivity distribution and the magnetic field
pattern. By changing the position of magnetic core, a set of voltage
differences is measured with a pair of electrodes. This set of voltage
differences is used in image reconstruction of conductivity
distribution. The least square error minimization method is used as a
reconstruction algorithm. The back projection algorithm is used to
get two dimensional images. Based on this principle, a measurement
system is developed and some model experiments were performed
with a saline filled phantom. The shape of each model in the
reconstructed image is similar to the corresponding model,
respectively. From the results of these experiments, it is confirmed
that the proposed method is applicable in the realization of electrical
imaging.
Abstract: power-line networks are promise infrastructure for
broadband services provision to end users. However, the network
performance is affected by stochastic channel changing which is due
to load impedances, number of branches and branched line lengths. It
has been proposed that multi-carrier modulations techniques such as
orthogonal frequency division multiplexing (OFDM), Multi-Carrier
Spread Spectrum (MC-SS), wavelet OFDM can be used in such
environment. This paper investigates the performance of different
indoor topologies of power-line networks that uses MC-SS
modulation scheme.It is observed that when a branch is added in the
link between sending and receiving end of an indoor channel an
average of 2.5dB power loss is found. In additional, when the branch
is added at a node an average of 1dB power loss is found.
Additionally when the terminal impedances of the branch change
from line characteristic impedance to impedance either higher or
lower values the channel performances were tremendously improved.
For example changing terminal load from characteristic impedance
(85 .) to 5 . the signal to noise ratio (SNR) required to attain the
same performances were decreased from 37dB to 24dB respectively.
Also, changing the terminal load from channel characteristic
impedance (85 .) to very higher impedance (1600 .) the SNR
required to maintain the same performances were decreased from
37dB to 23dB. The result concludes that MC-SS performs better
compared with OFDM techniques in all aspects and especially when
the channel is terminated in either higher or lower impedances.
Abstract: In this paper a novel high output impedance, low input impedance, wide bandwidth, very simple current mirror with input and output voltage requirements less than that of a simple current mirror is presented. These features are achieved with very simple structure avoiding extra large node impedances to ensure high bandwidth operation. The circuit's principle of operation is discussed and compared to simple and low voltage cascode (LVC) current mirrors. Such outstanding features of this current mirror as high output impedance ~384K, low input impedance~6.4, wide bandwidth~178MHz, low input voltage ~ 362mV, low output voltage ~ 38mV and low current transfer error ~4% (all at 50μA) makes it an outstanding choice for high performance applications. Simulation results in BSIM 0.35μm CMOS technology with HSPICE are given in comparison with simple, and LVC current mirrors to verify and validate the performance of the proposed current mirror.
Abstract: This paper presents a new approach for the protection
of Thyristor-Controlled Series Compensator (TCSC) line using
Support Vector Machine (SVM). One SVM is trained for fault
classification and another for section identification. This method use
three phase current measurement that results in better speed and
accuracy than other SVM based methods which used single phase
current measurement. This makes it suitable for real-time protection.
The method was tested on 10,000 data instances with a very wide
variation in system conditions such as compensation level, source
impedance, location of fault, fault inception angle, load angle at
source bus and fault resistance. The proposed method requires only
local current measurement.
Abstract: This paper proposes the method combining artificial neural network with particle swarm optimization (PSO) to implement the maximum power point tracking (MPPT) by controlling the rotor speed of the wind generator. With the measurements of wind speed, rotor speed of wind generator and output power, the artificial neural network can be trained and the wind speed can be estimated. The proposed control system in this paper provides a manner for searching the maximum output power of wind generator even under the conditions of varying wind speed and load impedance.
Abstract: A stack with a small critical temperature gradient is
desirable for a standing wave thermoacoustic engine to obtain a low
onset temperature difference (the minimum temperature difference to
start engine-s self-oscillation). The viscous and heat relaxation loss in
the stack determines the critical temperature gradient. In this work, a
dimensionless critical temperature gradient factor is obtained based
on the linear thermoacoustic theory. It is indicated that the
impedance determines the proportion between the viscous loss, heat
relaxation losses and the power production from the heat energy. It
reveals the effects of the channel dimensions, geometrical
configuration and the local acoustic impedance on the critical
temperature gradient in stacks. The numerical analysis shows that
there exists a possible optimum combination of these parameters
which leads to the lowest critical temperature gradient. Furthermore,
several different geometries have been tested and compared
numerically.
Abstract: An optimized design of E/O and O/E for access points
of WiMAX RoF was carried out by evaluating RCE. The use of the
DFB-LD, a low input-impedance driving, a low distortion PIN-PD,
and a high gain EPHEMT amplifier is promising the cost-effective
design. For the uplink RoF design, the use of EDFA and EP-HEMT
amplifiers is necessity.
Abstract: The control of oxygen flow rate during growth of
titanium dioxide by mass flow controller in DC plasma sputtering
growth system is studied. The impedance of TiO2 films for inductance
effect is influenced by annealing time and oxygen flow rate. As
annealing time is increased, the inductance of TiO2 film is the more.
The growth condition of optimum and maximum inductance for TiO2
film to serve as sensing device are oxygen flow rate of 15 sccm and
large annealing time. The large inductance of TiO2 film will be
adopted to fabricate the biosensor to obtain the high sensitivity of
sensing in biology.
Abstract: This paper presents a new method to detect high impedance faults in radial distribution systems. Magnitudes of third and fifth harmonic components of voltages and currents are used as a feature vector for fault discrimination. The proposed methodology uses a learning vector quantization (LVQ) neural network as a classifier for identifying high impedance arc-type faults. The network learns from the data obtained from simulation of a simple radial system under different fault and system conditions. Compared to a feed-forward neural network, a properly tuned LVQ network gives quicker response.