Abstract: We present our ongoing work on the development
of a new quadrotor aerial vehicle which has a tilt-wing
mechanism. The vehicle is capable of take-off/landing in vertical flight mode (VTOL) and flying over long distances in horizontal flight mode. Full dynamic model of the vehicle is derived using
Newton-Euler formulation. Linear and nonlinear controllers for
the stabilization of attitude of the vehicle and control of its
altitude have been designed and implemented via simulations. In particular, an LQR controller has been shown to be quite
effective in the vertical flight mode for all possible yaw angles. A sliding mode controller (SMC) with recursive nature has also
been proposed to stabilize the vehicle-s attitude and altitude. Simulation results show that proposed controllers provide
satisfactory performance in achieving desired maneuvers.
Abstract: From an economic standpoint the current and future
road traffic situation in urban areas is a cost factor. Traffic jams and
congestion prolong journey times and tie up resources in trucks and
personnel. Many discussions about imposing charges or tolls for
cities in Europe in order to reduce traffic congestion are currently in
progress. Both of these effects lead – directly or indirectly - to
additional costs for the urban distribution systems in retail
companies. One approach towards improving the efficiency of retail
distribution systems, and thus towards avoiding negative
environmental factors in urban areas, is horizontal collaboration for
deliveries to retail outlets – Urban Retail Logistics. This paper
presents a classification system to help reveal where cooperation
between retail companies is possible and makes sense for deliveries
to retail outlets in urban areas.
Abstract: The proper assessment of interaxial distance and
convergence control are important factors in stereoscopic imaging
technology to make an efficient 3D image. To control interaxial
distance and convergence for efficient 3D shooting, horizontal 3D
camera rig is designed using some hardware components like 'LM
Guide', 'Goniometer' and 'Rotation Stage'. The horizontal 3D camera
rig system can be properly aligned by moving the two cameras
horizontally in same or opposite directions, by adjusting the camera
angle and finally considering horizontal swing as well as vertical
swing. In this paper, the relationship between interaxial distance and
convergence angle control are discussed and intensive experiments are
performed in order to demonstrate an easy and effective 3D shooting.
Abstract: The recognition of handwritten numeral is an
important area of research for its applications in post office, banks
and other organizations. This paper presents automatic recognition of
handwritten Kannada numerals based on structural features. Five
different types of features, namely, profile based 10-segment string,
water reservoir; vertical and horizontal strokes, end points and
average boundary length from the minimal bounding box are used in
the recognition of numeral. The effect of each feature and their
combination in the numeral classification is analyzed using nearest
neighbor classifiers. It is common to combine multiple categories of
features into a single feature vector for the classification. Instead,
separate classifiers can be used to classify based on each visual
feature individually and the final classification can be obtained based
on the combination of separate base classification results. One
popular approach is to combine the classifier results into a feature
vector and leaving the decision to next level classifier. This method
is extended to extract a better information, possibility distribution,
from the base classifiers in resolving the conflicts among the
classification results. Here, we use fuzzy k Nearest Neighbor (fuzzy
k-NN) as base classifier for individual feature sets, the results of
which together forms the feature vector for the final k Nearest
Neighbor (k-NN) classifier. Testing is done, using different features,
individually and in combination, on a database containing 1600
samples of different numerals and the results are compared with the
results of different existing methods.
Abstract: Different variants for buoyancy-affected terms in k-ε turbulence model have been utilized to predict the flow parameters more accurately, and investigate applicability of alternative k-ε turbulence buoyant closures in numerical simulation of a horizontal gravity current. The additional non-isotropic turbulent stress due to buoyancy has been considered in production term, based on Algebraic Stress Model (ASM). In order to account for turbulent scalar fluxes, general gradient diffusion hypothesis has been used along with Boussinesq gradient diffusion hypothesis with a variable turbulent Schmidt number and additional empirical constant c3ε.To simulate buoyant flow domain a 2D vertical numerical model (WISE, Width Integrated Stratified Environments), based on Reynolds- Averaged Navier-Stokes (RANS) equations, has been deployed and the model has been further developed for different k-ε turbulence closures. Results are compared against measured laboratory values of a saline gravity current to explore the efficient turbulence model.
Abstract: The temperature distribution and the heat transfer
rates through a multi-layer door of a furnace were investigated. The
inside of the door was in contact with hot air and the other side of the
door was in contact with room air. Radiation heat transfer from the
walls of the furnace to the door and the door to the surrounding area
was included in the problem. This work is a two dimensional steady
state problem. The Churchill and Chu correlation was used to find
local convection heat transfer coefficients at the surfaces of the
furnace door. The thermophysical properties of air were the functions
of the temperatures. Polynomial curve fitting for the fluid properties
were carried out. Finite difference method was used to discretize for
conduction heat transfer within the furnace door. The Gauss-Seidel
Iteration was employed to compute the temperature distribution in
the door.
The temperature distribution in the horizontal mid plane of the
furnace door in a two dimensional problem agrees with the one
dimensional problem. The local convection heat transfer coefficients
at the inside and outside surfaces of the furnace door are exhibited.
Abstract: This paper presents an evaluation of the wind potential in the area of the Lagoon of Venice (Italy). A full anemometric campaign of 2 year measurements, performed by the "Osservatorio Bioclimatologico dell'Ospedale al Mare di Venezia" has been analyzed to obtain the Weibull wind speed distribution and the main wind directions. The annual energy outputs of two candidate horizontal-axis wind turbines (“Aventa AV-7 LoWind" and “Gaia Wind 133-11kW") have been estimated on the basis of the computed Weibull wind distribution, registering a better performance of the former turbine, due to a higher ratio between rotor swept area and rated power of the electric generator, determining a lower cut-in wind speed.
Abstract: We developed a method based on quasi-molecular
modelling to simulate the fall of water drops on horizontally smooth
and rough surfaces. Each quasi-molecule was a group of particles
that interacted in a fashion entirely analogous to classical Newtonian
molecular interactions. When a falling water droplet was simulated at
low impact velocity on both smooth and rough surfaces, the droplets
moved periodically (i.e. the droplets moved up and down for a
certain period, finally they stopped moving and reached a steady
state), spreading and recoiling without splash or break-up. Spreading
rates of falling water droplets increased rapidly as time increased
until the spreading rate reached its steady state at time t ~ 0.25 s for
rough surface and t ~ 0.40 s for smooth surface. The droplet height
above both surfaces decreased as time increased, remained constant
after the droplet diameter attained a maximum value and reached its
steady state at time t ~ 0.4 s. However, rough surface had higher
spreading rates of falling water droplets and lower height on the
surface than smooth one.
Abstract: Horizontal continuous casting is widely used to
produce semi-finished non-Ferrous products. Homogeneity in the
metallurgical characteristics and mechanical properties for this
product is vital for industrial application. In the present work, the
microstructure and mechanical properties of a horizontal continuous
cast two-phase brass billet have been studied. Impact strength and
hardness variations were examined and the phase composition and
porosity studied with image analysis software. Distinct differences in
mechanical properties were observed between the upper, middle and
lower parts of the billet, which are explained in terms of the
morphology and size of the phase in the microstructure. Hardness
variation in the length of billet is higher in upper area but impact
strength is higher in lower areas.
Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: This research investigates the effects of the opening
shape and location on the structural behavior of reinforced concrete
deep beam with openings, while keeping the opening size unchanged.
The software ANSYS 12.1 is used to handle the nonlinear finite
element analysis. The ultimate strength of reinforced concrete deep
beam with opening obtained by ANSYS 12.1 shows fair agreement
with the experimental results, with a difference of no more than 20%. The present work concludes that the opening location has much more effect on the structural strength than the opening shape. It was
concluded that placing the openings near the upper corners of the
deep beam may double the strength, and the use of a rectangular
narrow opening, with the long sides in the horizontal direction, can save up to 40% of structural strength of the deep beam.
Abstract: Although many studies on the assembly technology of
the bridge construction have dealt mostly with on the pier, girder or the
deck of the bridge, studies on the prefabricated barrier have rarely been
performed. For understanding structural characteristics and
application of the concrete barrier in the modular bridge, which is an
assembly of structure members, static loading test was performed.
Structural performances as a road barrier of the three methods,
conventional cast-in-place(ST), vertical bolt connection(BVC) and
horizontal bolt connection(BHC) were evaluated and compared
through the analyses of load-displacement curves, strain curves of the
steel, concrete strain curves and the visual appearances of crack
patterns. The vertical bolt connection(BVC) method demonstrated
comparable performance as an alternative to conventional
cast-in-place(ST) while providing all the advantages of prefabricated
technology. Necessities for the future improvement in nuts
enforcement as well as legal standard and regulation are also
addressed.
Abstract: A model of vortex wake is suggested to determine the
induced power during animal hovering flight. The wake is modeled
by a series of equi-spaced rigid rectangular vortex plates, positioned
horizontally and moving vertically downwards with identical speeds;
each plate is generated during powering of the functionally wing
stroke. The vortex representation of the wake considered in the
current theory allows a considerable loss of momentum to occur. The
current approach accords well with the nature of the wingbeat since it
considers the unsteadiness in the wake as an important fluid
dynamical characteristic. Induced power in hovering is calculated as
the aerodynamic power required to generate the vortex wake system.
Specific mean induced power to mean wing tip velocity ratio is
determined by solely the normal spacing parameter (f) for a given
wing stroke amplitude. The current theory gives much higher specific
induced power estimate than anticipated by classical methods.
Abstract: The integrity and issues related to electrostatic performance associated with scaling Si MOSFET bulk sub 10nm channel length promotes research in new device architectures such as SOI, double gate and GAA MOSFET. In this paper, we present some novel characteristic of horizontal rectangular gate\gate all around MOSFETs with dual metal of gate we obtained using SILVACO TCAD tools. We will also exhibit some simulation results we obtained relating to the influence of some parameters variation on our structure, that having a direct impact on their threshold voltage and drain current. In addition, our TFET showed reasonable ION/IOFF ratio of (104) and low drain induced barrier lowering (DIBL) of 39 mV/V.
Abstract: Based on Rayleigh beam theory, the sub-impacts of a
free-free beam struck horizontally by a round-nosed rigid mass is
simulated by the finite difference method and the impact-separation
conditions. In order to obtain the sub-impact force, a uniaxial
compression elastic-plastic contact model is employed to analyze the
local deformation field on contact zone. It is found that the horizontal
impact is a complicated process including the elastic plastic
sub-impacts in sequence. There are two sub-zones of sub-impact. In
addition, it found that the elastic energy of the free-free beam is more
suitable for the Poisson collision hypothesis to explain compression
and recovery processes.
Abstract: Recently, as information industry and mobile
communication technology are developing, this study is conducted on
the new concept of intelligent structures and maintenance techniques
that applied wireless sensor network, USN (Ubiquitous Sensor
Network), to social infrastructures such as civil and architectural
structures on the basis of the concept of Ubiquitous Computing that
invisibly provides human life with computing, along with mutually
cooperating, compromising and connecting networks each other by
having computers within all objects around us.
Therefore, the purpose of this study is to investigate the capability
of wireless communication of sensor node embedded in reinforced
concrete structure with a basic experiment on an electric wave
permeability of sensor node by fabricating molding with variables of
concrete thickness and steel bars that are mostly used in constructing
structures to determine the feasibility of application to constructing
structures with USN.
At this time, with putting the pitches of steel bars, the thickness of
concrete placed, and the intensity of RF signal of a
transmitter-receiver as variables and when wireless communication
module was installed inside, the possible communication distance of
plain concrete and the possible communication distance by the pitches
of steel bars was measured in the horizontal and vertical direction
respectively. Besides, for the precise measurement of diminution of an
electric wave, the magnitude of an electric wave in the range of used
frequencies was measured by using Spectrum Analyzer. The
phenomenon of diminution of an electric wave was numerically
analyzed and the effect of the length of wavelength of frequencies was
analyzed by the properties of a frequency band area.
As a result of studying the feasibility of an application to
constructing structures with wireless sensor, in case of plain concrete,
it shows 45cm for the depth of permeability and in case of reinforced
concrete with the pitches of 5cm, it shows 37cm and 45cm for the
pitches of 15cm.
Abstract: The time dependent progress of a chemical reaction over a flat horizontal plate is here considered. The problem is solved through the group similarity transformation method which reduces the number of independent by one and leads to a set of nonlinear ordinary differential equation. The problem shows a singularity at the chemical reaction order n=1 and is analytically solved through the perturbation method. The behavior of the process is then numerically investigated for n≠1 and different Schmidt numbers. Graphical results for the velocity and concentration of chemicals based on the analytical and numerical solutions are presented and discussed.
Abstract: In this work, the natural convection in a concentric
annulus between a cold outer inclined square enclosure and heated
inner circular cylinder is simulated for two-dimensional steady
state. The Boussinesq approximation was applied to model the
buoyancy-driven effect and the governing equations were solved
using the time marching approach staggered by body fitted
coordinates. The coordinate transformation from the physical
domain to the computational domain is set up by an analytical
expression. Numerical results for Rayleigh numbers 103 , 104 , 105
and 106, aspect ratios 1.5 , 3.0 and 4.5 for seven different
inclination angles for the outer square enclosure 0o , -30o
, -45o
,
-60o , -90o , -135o , -180o are presented as well. The computed flow
and temperature fields were demonstrated in the form of
streamlines, isotherms and Nusselt numbers variation. It is found
that both the aspect ratio and the Rayleigh number are critical to the
patterns of flow and thermal fields. At all Rayleigh numbers angle
of inclination has nominal effect on heat transfer.