Abstract: In this paper, all-optical signal processors that perform
both microwave mixing and bandpass filtering in a radio-over-fiber
(RoF) link are presented. The key device is a Mach-Zehnder
modulator (MZM) which performs all-optical microwave mixing. An
up-converted microwave signal is obtained and other unwanted
frequency components are suppressed at the end of the fiber span.
Abstract: This paper investigates experimentally and
analytically the torsion behavior of steel fibered high strength self
compacting concrete beams reinforced by GFRP bars. Steel fibered
high strength self compacting concrete (SFHSSCC) and GFRP bars
became in the recent decades a very important materials in the
structural engineering field. The use of GFRP bars to replace steel
bars has emerged as one of the many techniques put forward to
enhance the corrosion resistance of reinforced concrete structures.
High strength concrete and GFRP bars attract designers and
architects as it allows improving the durability as well as the esthetics
of a construction. One of the trends in SFHSSCC structures is to
provide their ductile behavior and additional goal is to limit
development and propagation of macro-cracks in the body of
SFHSSCC elements. SFHSSCC and GFRP bars are tough, improve
the workability, enhance the corrosion resistance of reinforced
concrete structures, and demonstrate high residual strengths after
appearance of the first crack. Experimental studies were carried out
to select effective fiber contents. Three types of volume fraction from
hooked shape steel fibers are used in this study, the hooked steel
fibers were evaluated in volume fractions ranging between 0.0%,
0.75% and 1.5%. The beams shape is chosen to create the required
forces (i.e. torsion and bending moments simultaneously) on the test
zone. A total of seven beams were tested, classified into three groups.
All beams, have 200cm length, cross section of 10×20cm,
longitudinal bottom reinforcement of 3
Abstract: Inthis paper, design and fabrication of vertical
micromirror for optical switching applications of single mode optical
fibers are proposed. The structure of micromirror will be created
from negative photoresist (SU-8) on X-ray lithography using X-ray
from synchrotron light source. The properties of X-ray from
synchrotron light source are high-energy electrons which can
construct materials that have a high aspect ratio. In addition, the
technique of gold coating of reflective material has been used for
change direction of light between two pairs of optical fibers. At a
wavelength of 1310 nm with minimum average loss of 5.305 dB is
obtained.
Abstract: High strength concrete has been used in situations
where it may be exposed to elevated temperatures. Numerous authors
have shown the significant contribution of polypropylene fiber to the
spalling resistance of high strength concrete.
When cement-based composite that reinforced by polypropylene
fibers heated up to 170 °C, polypropylene fibers readily melt and
volatilize, creating additional porosity and small channels in to the
matrix that cause the poor structure and low strength.
This investigation develops on the mechanical properties of mortar
incorporating polypropylene fibers exposed to high temperature.
Also effects of different pozzolans on strength behaviour of samples
at elevated temperature have been studied.
To reach this purpose, the specimens were produced by partial
replacement of cement with finely ground glass, silica fume and rice
husk ash as high reactive pozzolans. The amount of this replacement
was 10% by weight of cement to find the effects of pozzolans as a
partial replacement of cement on the mechanical properties of
mortars. In this way, lots of mixtures with 0%, 0.5%, 1% and 1.5% of
polypropylene fibers were cast and tested for compressive and
flexural strength, accordance to ASTM standard. After that
specimens being heated to temperatures of 300, 600 °C, respectively,
the mechanical properties of heated samples were tested.
Mechanical tests showed significant reduction in compressive
strength which could be due to polypropylene fiber melting. Also
pozzolans improve the mechanical properties of sampels.
Abstract: In this study, single nozzle method used for
electrospinning technique which composite polymer solution with
cellulose nanowiskers (CNW) was treated by ultrasonic sonificator
have been compared with coaxial (double) nozzle method, in terms of
mechanical, thermal and morphological properties of composite
nanofiber. The effect of water content in composite polymer solution
on properties of nanofiber has also been examined. It has been seen
that single nozzle method which polymer solution does not contain
water has better results than that of coaxial method, in terms of
mechanical, thermal and morphological properties of nanofiber.
However, it is necessary to make an optimization study on setting
condition of ultrasonic treatment to get better dispersion of CNW in
composite nanofiber and to get better mechanical and thermal
properties
Abstract: Bionanotechnology deals with nanoscopic interactions between nanostructured materials and biological systems. Polymer nanocomposites with optimized biological activity have attracted great attention. Nanoclay is considered as reinforcing nanofiller in manufacturing of high performance nanocomposites. In current study, organomodified-nanoclay with negatively charged silicate layers was incorporated into biomedical grade silicone rubber. Nanoparticle loading has been tailored to enhance cell behavior. Addition of nanoparticles led to improved mechanical properties of substrate with enhanced strength and stiffness while no toxic effects was observed. Results indicated improved viability and proliferation of cells by addition of nanofillers. The improved mechanical properties of the matrix result in proper cell response through adjustment and arrangement of cytoskeletal fibers. Results can be applied in tissue engineering when enhanced substrates are required for improvement of cell behavior for in vivo applications.
Abstract: Nuts are part of a healthy diet such as Mediterranean diet. Benefits of nuts in reducing the risk of heart disease has been reasonably attributed to their composition of vitamins, minerals, unsaturated fatty acids, fiber and phytochemicals such as polyphenols, tocopherols, squalene and phytosterols. More than 75% of total fatty acids of nuts are unsaturated. α- tocopherol is the main tocopherol isomer present in most of the nuts. While walnuts, Brazil nut, cashew nut, peanut, pecan and pistachio nuts are rich in γ- tocopherol. β- sitosterol is dominant sterol in nuts. Pistachio and pine nut have the highest total phytosterol and Brazil nut and English walnut the lowest. Walnuts also contain large amount of phenolic compounds compared with other nuts. Nuts are rich in compounds with antioxidant properties and their consumption can offer preventing from incidence of many diseases including cardiovascular.
Abstract: In this paper, a new alignment method based on the particle swarm optimization (PSO) technique is presented. The PSO algorithm is used for locating the optimal coupling position with the highest optical power with three-degrees of freedom alignment. This algorithm gives an interesting results without a need to go thru the complex mathematical modeling of the alignment system. The proposed algorithm is validated considering practical tests considering the alignment of two Single Mode Fibers (SMF) and the alignment of SMF and PCF fibers.
Abstract: The machining of Carbon Fiber Reinforced Plastics
has come to constitute a significant challenge for many fields of
industry. The resulting surface finish of machined parts is of primary
concern for several reasons, including contact quality and impact on
the assembly. Therefore, the characterization and prediction of
roughness based on machining parameters are crucial for costeffective
operations. In this study, a PCD tool comprised of two
straight flutes was used to trim 32-ply carbon fiber laminates in a bid
to analyze the effects of the feed rate and the cutting speed on the
surface roughness. The results show that while the speed has but a
slight impact on the surface finish, the feed rate for its part affects it
strongly. A detailed study was also conducted on the effect of fiber
orientation on surface roughness, for quasi-isotropic laminates used
in aerospace. The resulting roughness profiles for the four-ply
orientation lay-up were compared, and it was found that fiber angle is
a critical parameter relating to surface roughness. One of the four
orientations studied led to very poor surface finishes, and
characteristic roughness profiles were identified and found to only
relate to the ply orientations of multilayer carbon fiber laminates.
Abstract: The effect of varying holding temperature on hatching success, occurrence of deformities and mortality rates were investigated for goldlined seabream eggs. Wild broodstock (600 g) were stocked at a 2:1 male-female ratio in a 2 m3 fiberglass tank supplied with filtered seawater (37 g L-1 salinity, temp. range 24±0.5 oC [day] and 22±1 oC [night], DO2 in excess of 5.0mg L-1). Females were injected with 200 IU kg-1 HCG between 08.00 and 10.00 h and returned to tanks to spawn following which eggs were collected by hand using a 100μm net. Fertilized eggs at the gastrulation stage (120 L-1) were randomly placed into one of 12 experimental 6 L aerated (DO2 5 mg L-1) plastic containers with water temperatures maintained at 24±0.5 oC (ambient), 26±0.5 oC, 28± 0.5 oC and 30±0.5 oC using thermostats. Each treatment was undertaken in triplicate using a 12:12 photophase:scotophase photoperiod. No differences were recorded between eggs reared at 24 and 26 oC with respect to viability, deformity, mortality or unhatched egg rates. Increasing temperature reduced the number of viable eggs with those at 30 oC returning poorest performance (P < 0.05). Mortality levels were lowest for eggs incubated at 24 and 26 oC. The greatest level of deformities recorded was that for eggs reared at 28 oC.
Abstract: In this study, The physico-chemical and nutritional
properties of `Musmula` Medlar (Mespilus germanica L.) fruit and
seed grown in Northeast Anatolia was investigated. In the fruit,
length, width, thickness, weight, total soluble solids, colour (1),
colour (2) [L, a, b values], protein, crude ash, crude fiber, crude oil,
texture and pH were determinated as 4.34 cm, 4.22 cm, 3.67 cm,
38.36 g, 23.97 %, S60O60Y41,, [53.85, 17.15, 33.75], 1.06 %, 0.79 %,
4.24 %, 0.005 %, 1.21 kg/cm2 and 4.26 respectively. Also, pulp ratio,
seed ratio and pulp/seed ratio were found to be 92.88 %, 7.11 % and
14.07 %, respectively. In addition, the mineral composition of medlar
fruit in Northeast Anatolia was studied. In the fruit, 23 minerals were
analyzed and 19 minerals were present at detectable levels. The
medlar fruit was richest in potassium (6962 ppm), calcium (1186.378
ppm), magnesium (1070.08 ppm) and phosphor (763.425 ppm).
Abstract: Road industry has challenged the prospect of ecoconstruction. Pavements may fit within the framework of sustainable development. Hence, research implements assessments of conventional pavements impacts on environment in use of life cycle approach. To meet global, and often national, targets on pollution control, newly introduced pavement designs are under study. This is the case of Cyprus demonstration, which occurred within EcoLanes project work. This alternative pavement differs on concrete layer reinforced with tire recycling product. Processing of post-consumer tires produces steel fibers improving strength capacity against cracking. Thus maintenance works are relevantly limited in comparison to flexible pavement. This enables to be more ecofriendly, referenced to current study outputs. More specific, proposed concrete pavement life cycle processes emits 15 % less air pollutants and consumes 28 % less embodied energy than those of the asphalt pavement. In addition there is also a reduction on costs by 0.06 %.
Abstract: We present the development of a new underwater laser
cutting process in which a water-jet has been used along with the
laser beam to remove the molten material through kerf. The
conventional underwater laser cutting usually utilizes a high pressure
gas jet along with laser beam to create a dry condition in the cutting
zone and also to eject out the molten material. This causes a lot of gas
bubbles and turbulence in water, and produces aerosols and waste
gas. This may cause contamination in the surrounding atmosphere
while cutting radioactive components like burnt nuclear fuel. The
water-jet assisted underwater laser cutting process produces much
less turbulence and aerosols in the atmosphere. Some amount of
water vapor bubbles is formed at the laser-metal-water interface;
however, they tend to condense as they rise up through the
surrounding water. We present the design and development of a
water-jet assisted underwater laser cutting head and the parametric
study of the cutting of AISI 304 stainless steel sheets with a 2 kW
CW fiber laser. The cutting performance is similar to that of the gas
assist laser cutting; however, the process efficiency is reduced due to
heat convection by water-jet and laser beam scattering by vapor. This
process may be attractive for underwater cutting of nuclear reactor
components.
Abstract: In order to evaluation the effects of soil organic
matter and biofertilizer on chickpea quality and biological
nitrogen fixation, field experiments were carried out in 2007
and 2008 growing seasons. In this research the effects of
different strategies for soil fertilization were investigated on
grain yield and yield component, minerals, organic compounds
and cooking time of chickpea. Experimental units were
arranged in split-split plots based on randomized complete
blocks with three replications. Main plots consisted of (G1):
establishing a mixed vegetation of Vicia panunica and
Hordeum vulgare and (G2): control, as green manure levels.
Also, five strategies for obtaining the base fertilizer
requirement including (N1): 20 t.ha-1 farmyard manure; (N2):
10 t.ha-1 compost; (N3): 75 kg.ha-1 triple super phosphate;
(N4): 10 t.ha-1 farmyard manure + 5 t.ha-1 compost and (N5):
10 t.ha-1 farmyard manure + 5 t.ha-1 compost + 50 kg.ha-1
triple super phosphate were considered in sub plots.
Furthermoree four levels of biofertilizers consisted of (B1):
Bacillus lentus + Pseudomonas putida; (B2): Trichoderma
harzianum; (B3): Bacillus lentus + Pseudomonas putida +
Trichoderma harzianum; and (B4): control (without
biofertilizers) were arranged in sub-sub plots. Results showed
that integrating biofertilizers (B3) and green manure (G1)
produced the highest grain yield. The highest amounts of yield
were obtained in G1×N5 interaction. Comparison of all 2-way
and 3-way interactions showed that G1N5B3 was determined
as the superior treatment. Significant increasing of N, P2O5,
K2O, Fe and Mg content in leaves and grains emphasized on
superiority of mentioned treatment because each one of these
nutrients has an approved role in chlorophyll synthesis and
photosynthesis abilities of the crops. The combined application
of compost, farmyard manure and chemical phosphorus (N5)
in addition to having the highest yield, had the best grain
quality due to high protein, starch and total sugar contents, low
crude fiber and reduced cooking time.
Abstract: In this paper we study the use of a new code called
Random Diagonal (RD) code for Spectral Amplitude Coding (SAC)
optical Code Division Multiple Access (CDMA) networks, using
Fiber Bragg-Grating (FBG), FBG consists of a fiber segment whose
index of reflection varies periodically along its length. RD code is
constructed using code level and data level, one of the important
properties of this code is that the cross correlation at data level is
always zero, which means that Phase intensity Induced Phase (PIIN)
is reduced. We find that the performance of the RD code will be
better than Modified Frequency Hopping (MFH) and Hadamard code
It has been observed through experimental and theoretical simulation
that BER for RD code perform significantly better than other codes.
Proof –of-principle simulations of encoding with 3 channels, and 10
Gbps data transmission have been successfully demonstrated together
with FBG decoding scheme for canceling the code level from SAC-signal.
Abstract: The term hybrid composite refers to the composite
containing more than one type of fiber material as reinforcing fillers.
It has become attractive structural material due to the ability of
providing better combination of properties with respect to single fiber
containing composite. The eco-friendly nature as well as processing
advantage, light weight and low cost have enhanced the attraction
and interest of natural fiber reinforced composite. The objective of
present research is to study the mechanical properties of jute-coir
fiber reinforced hybrid polypropylene (PP) composite according to
filler loading variation. In the present work composites were
manufactured by using hot press machine at four levels of fiber
loading (5, 10, 15 and 20 wt %). Jute and coir fibers were utilized at a
ratio of (1:1) during composite manufacturing. Tensile, flexural,
impact and hardness tests were conducted for mechanical
characterization. Tensile test of composite showed a decreasing trend
of tensile strength and increasing trend of the Young-s modulus with
increasing fiber content. During flexural, impact and hardness tests,
the flexural strength, flexural modulus, impact strength and hardness
were found to be increased with increasing fiber loading. Based on
the fiber loading used in this study, 20% fiber reinforced composite
resulted the best set of mechanical properties.
Abstract: In this investigation, types of commercial and special
polyacrylonitrile (PAN) fibers contain sodium 2-methyl-2-
acrylamidopropane sulfonate (SAMPS) and itaconic acid (IA)
comonomers were studied by fourier transform infrared (FT-IR)
spectroscopy. The study of FT-IR spectra of PAN fibers samples
with different comonomers shows that during stabilization of PAN
fibers, the peaks related to C≡N bonds and CH2 are reduced sharply.
These reductions are related to cyclization of nitrile groups and
stabilization procedure. This reduction in PAN fibers contain IA
comonomer is very intense in comparison with PAN fibers contain
SAMPS comonomer. This fact indicates the cycling and stabilization
for sample contain IA comonomer have been conducted more
completely. Therefore the carbon fibers produced from this material
have higher tensile strength due to suitable stabilization.
Abstract: Heat powered solid sorption is a feasible alternative to
electrical vapor compression refrigeration systems. In this paper,
activated carbon (powder type Maxsorb and fiber type ACF-A10)-
CO2 based adsorption cooling cycles are studied using the pressuretemperature-
concentration (P-T-W) diagram. The specific cooling
effect (SCE) and the coefficient of performance (COP) of these two
cooling systems are simulated for the driving heat source
temperatures ranging from 30 ºC to 90 ºC in terms of different
cooling load temperatures with a cooling source temperature of 25
ºC. It is found from the present analysis that Maxsorb-CO2 couple
shows higher cooling capacity and COP. The maximum COPs of
Maxsorb-CO2 and ACF(A10)-CO2 based cooling systems are found
to be 0.15 and 0.083, respectively. The main innovative feature of
this cooling cycle is the ability to utilize low temperature waste heat
or solar energy using CO2 as the refrigerant, which is one of the best
alternative for applications where flammability and toxicity are not
allowed.
Abstract: This paper presents a generalized formulation for the
problem of buckling optimization of anisotropic, radially graded,
thin-walled, long cylinders subject to external hydrostatic pressure.
The main structure to be analyzed is built of multi-angle fibrous
laminated composite lay-ups having different volume fractions of the
constituent materials within the individual plies. This yield to a
piecewise grading of the material in the radial direction; that is the
physical and mechanical properties of the composite material are
allowed to vary radially. The objective function is measured by
maximizing the critical buckling pressure while preserving the total
structural mass at a constant value equals to that of a baseline
reference design. In the selection of the significant optimization
variables, the fiber volume fractions adjoin the standard design
variables including fiber orientation angles and ply thicknesses. The
mathematical formulation employs the classical lamination theory,
where an analytical solution that accounts for the effective axial and
flexural stiffness separately as well as the inclusion of the coupling
stiffness terms is presented. The proposed model deals with
dimensionless quantities in order to be valid for thin shells having
arbitrary thickness-to-radius ratios. The critical buckling pressure
level curves augmented with the mass equality constraint are given
for several types of cylinders showing the functional dependence of
the constrained objective function on the selected design variables. It
was shown that material grading can have significant contribution to
the whole optimization process in achieving the required structural
designs with enhanced stability limits.
Abstract: In the first part of the research work, an electrolyzer (10.16 cm dia and 24.13 cm height) to produce hydrogen and oxygen was constructed for single slice O2/H2 fuel cell using cation exchange membrane. The electrolyzer performance was tested with 23% NaOH, 30% NaOH, 30% KOH and 35% KOH electrolyte solution with current input 4 amp and 2.84 V from the rectifier. Rates of volume of hydrogen produced were 0.159 cm3/sec, 0.155 cm3/sec, 0.169 cm3/sec and 0.163 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution. Rates of volume of oxygen produced were 0.212 cm3/sec, 0.201 cm3/sec, 0.227 cm3/sec and 0.219 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution (1.5 L). In spite of being tested the increased concentration of electrolyte solution, the gas rate does not change significantly. Therefore, inexpensive 23% NaOH electrolyte solution was chosen to use as the electrolyte in the electrolyzer. In the second part of the research work, graphite serpentine flow plates, fiberglass end plates, stainless steel screen electrodes, silicone rubbers were made to assemble the single slice O2/H2 polymer electrolyte membrane fuel cell (PEMFC).