Abstract: This paper describes a blind algorithm for estimating a time varying and frequency selective fading channel. In order to identify blindly the impulse response of these channels, we have used Higher Order Statistics (HOS) to build our algorithm. In this paper, we have selected two theoretical frequency selective channels as the Proakis-s 'B' channel and the Macchi-s channel, and one practical frequency selective fading channel called Broadband Radio Access Network (BRAN A). The simulation results in noisy environment and for different data input channel, demonstrate that the proposed method could estimate the phase and magnitude of these channels blindly and without any information about the input, except that the input excitation is i.i.d (Identically and Independent Distributed) and non-Gaussian.
Abstract: The large and small-scale shaking table tests, which
was conducted for investigating damage evolution of piles inside
liquefied soil, are numerically simulated and experimental verified by the3D nonlinear finite element analysis. Damage evolution of
elasto-plastic circular steel piles and reinforced concrete (RC) one with cracking and yield of reinforcement are focused on, and the failure patterns and residual damages are captured by the proposed constitutive models. The superstructure excitation behind quay wall is
reproduced as well.
Abstract: The experimental and theoretical results of a ZVS
(Zero Voltage Switching) isolated flyback DC-DC converter using
multilayered coreless PCB step down 2:1 transformer are presented.
The performance characteristics of the transformer are shown which
are useful for the parameters extraction. The measured energy
efficiency of the transformer is found to be more than 94% with the
sinusoidal input voltage excitation. The designed flyback converter
has been tested successfully upto the output power level of 10W,
with a switching frequency in the range of 2.7MHz-4.3MHz. The
input voltage of the converter is varied from 25V-40V DC.
Frequency modulation technique is employed by maintaining
constant off time to regulate the output voltage of the converter. The
energy efficiency of the isolated flyback converter circuit under ZVS
condition in the MHz frequency region is found to be approximately
in the range of 72-84%. This paper gives the comparative results in
terms of the energy efficiency of the hard switched and soft switched
flyback converter in the MHz frequency region.
Abstract: Vibration characteristics of subcooled flow boiling on
thin and long structures such as a heating rod were recently
investigated by the author. The results show that the intensity of the
subcooled boiling-induced vibration (SBIV) was influenced strongly
by the conditions of the subcooling temperature, linear power density
and flow velocity. Implosive bubble formation and collapse are the
main nature of subcooled boiling, and their behaviors are the only
sources to originate from SBIV. Therefore, in order to explain the
phenomenon of SBIV, it is essential to obtain reliable information
about bubble behavior in subcooled boiling conditions. This was
investigated at different conditions of coolant subcooling
temperatures of 25 to 75°C, coolant flow velocities of 0.16 to
0.53m/s, and linear power densities of 100 to 600 W/cm. High speed
photography at 13,500 frames per second was performed at these
conditions. The results show that even at the highest subcooling
condition, the absolute majority of bubbles collapse very close to the
surface after detaching from the heating surface. Based on these
observations, a simple model of surface tension and momentum
change is introduced to offer a rough quantitative estimate of the
force exerted on the heating surface during the bubble ebullition. The
formation of a typical bubble in subcooled boiling is predicted to
exert an excitation force in the order of 10-4 N.
Abstract: This paper describes the design and modeling
procedure of a novel 5-phase segment type switched reluctance motor
(ST-SRM) under simultaneous two-phase (bipolar) excitation of
windings. The rotor cores of ST-SRM are embedded in an aluminum
block as well as to improve the performance characteristics. The
magnetic circuit of the produced ST-SRM is constructed so that the
magnetic flux paths are short and exclusive to each phase, thereby
minimizing the commutation switching and eddy current losses in the
laminations. The design and simulation principles presented apply
primarily to conventional SRM and ST-SRM. It is proved that the
novel 5-phase switched reluctance motor under two-phase excitation
is superior among the criteria used in comparison. The purposed
model is particularly well suited for high torque and weight
constrained applications such as automobiles, aerospace and military
applications.
Abstract: This paper emphasizes on the application of genetic algorithm (GA) to optimize the parameters of the TMD for achieving the best results in the reduction of the building response under earthquake excitations. The Integral of the Time multiplied Absolute value of the Error (ITAE) based on relative displacement of all floors in the building is taken as a performance index of the optimization criterion. The problem of robustly TMD controller design is formatted as an optimization problem based on the ITAE performance index to be solved using GA that has a story ability to find the most optimistic results. An 11–story realistic building, located in the city of Rasht, Iran is considered as a test system to demonstrate effectiveness of the proposed GA based TMD (GATMD) controller without specifying which mode should be controlled. The results of the proposed GATMD controller are compared with the uncontrolled structure through timedomain simulation and some performance indices. The results analysis reveals that the designed GA based TMD controller has an excellent capability in reduction of the seismically excited example building and the ITAE performance, that is so for remains as unknown, can be introduced a new criteria - method for structural dynamic design.
Abstract: Electromagnetic flowmeters with DC excitation are used for a wide range of fluid measurement tasks, but are rarely found in dosing applications with short measurement cycles due to the achievable accuracy. This paper will identify a number of factors that influence the accuracy of this sensor type when used for short-term measurements. Based on these results a new signal-processing algorithm will be described that overcomes the identified problems to some extend. This new method allows principally a higher accuracy of electromagnetic flowmeters with DC excitation than traditional methods.
Abstract: This paper describes the development of a numerical finite element algorithm used for the analysis of reinforced concrete structure equipped with shakes energy absorbing device subjected to earthquake excitation. For this purpose a finite element program code for analysis of reinforced concrete frame buildings is developed. The performance of developed program code is evaluated by analyzing of a reinforced concrete frame buildings model. The results are show that using damper device as seismic energy dissipation system effectively can reduce the structural response of framed structure during earthquake occurrence.
Abstract: The paper presents the study of synthetic transmit
aperture method applying the Golay coded transmission for medical
ultrasound imaging. Longer coded excitation allows to increase the
total energy of the transmitted signal without increasing the peak
pressure. Signal-to-noise ratio and penetration depth are improved
maintaining high ultrasound image resolution.
In the work the 128-element linear transducer array with 0.3 mm
inter-element spacing excited by one cycle and the 8 and 16-bit
Golay coded sequences at nominal frequencies 4 MHz was used.
Single element transmission aperture was used to generate a spherical
wave covering the full image region and all the elements received the
echo signals. The comparison of 2D ultrasound images of the wire
phantom as well as of the tissue mimicking phantom is presented to
demonstrate the benefits of the coded transmission. The results were
obtained using the synthetic aperture algorithm with transmit and
receive signals correction based on a single element directivity
function.
Abstract: This paper focuses on the Mega-Sub Controlled
Structure Systems (MSCSS) performances and characteristics
regarding the new control principle contained in MSCSS subjected to
strong earthquake excitations. The adopted control scheme consists of
modulated sub-structures where the control action is achieved by
viscous dampers and sub-structure own configuration. The
elastic-plastic time history analysis under severe earthquake excitation
is analyzed base on the Finite Element Analysis Method (FEAM), and
some comparison results are also given in this paper. The result shows
that the MSCSS systems can remarkably reduce vibrations effects
more than the mega-sub structure (MSS). The study illustrates that the
improved MSCSS presents good seismic resistance ability even at 1.2g
and can absorb seismic energy in the structure, thus imply that
structural members cross section can be reduce and achieve to good
economic characteristics. Furthermore, the elasto-plastic analysis
demonstrates that the MSCSS is accurate enough regarding
international building evaluation and design codes. This paper also
shows that the elasto-plastic dynamic analysis method is a reasonable
and reliable analysis method for structures subjected to strong
earthquake excitations and that the computed results are more precise.
Abstract: A facile vapour deposition method of synthesis of vertically aligned ZnO nanowires on carbon seed layer was developed. The received samples were investigated on electronic microscope JSM-6490 LA JEOL and x-ray diffractometer X, pert MPD PRO. The photoluminescence spectra (PL) of obtained ZnO samples at a room temperature were studied using He-Cd laser (325 nm line) as excitation source.
Abstract: In this study, shaking table tests are performed to investigate the behavior of excess pore water pressure in different soft soil-foundations of soil-structure interaction (SSI) system. The variation of the behaviors under cycled minor shock is observed. Moreover, The generation and variation mechanism of excess pore water pressure under earthquake excitation in different soft soilfoundations are analyzed and discussed.
Abstract: The vibrations produced by a single point defect on
various parts of the bearing under constant radial load are predicted
by using a theoretical model. The model includes variation in the
response due to the effect of bearing dimensions, rotating frequency
distribution of load. The excitation forces are generated when the
defects on the races strike to rolling elements. In case of the outer
ring defect, the pulses generated are with periodicity of outer ring
defect frequency where as for inner ring defect, the pulses are with
periodicity of inner ring defect frequency. The effort has been carried
out in preparing the physical model of the system. Different defect
frequencies are obtained and are used to find out the amplitudes of
the vibration due to excitation of the bearing parts. Increase in the
radial load or severity of the defect produces a significant change in
bearing signature characteristics.
Abstract: Response surface methodology with Box–Benhken (BB) design of experiment approach has been utilized to study the mechanism of interface slip damping in layered and jointed tack welded beams with varying surface roughness. The design utilizes the initial amplitude of excitation, tack length and surface roughness at the interfaces to develop the model for the logarithmic damping decrement of the layered and jointed welded structures. Statistically designed experiments have been performed to estimate the coefficients in the mathematical model, predict the response, and check the adequacy of the model. Comparison of predicted and experimental response values outside the design conditions have shown good correspondence, implying that empirical model derived from response surface approach can be effectively used to describe the mechanism of interface slip damping in layered and jointed tack welded structures.
Abstract: The available data on the cross sections of electronimpact
excitation of krypton 5s and 5p configuration levels out of the
ground state are represented in convenient and compact form. The
results are obtained by regression through all known published data
related to this process.
Abstract: This paper presents a NDT by infrared thermography with excitation CO2 Laser, wavelength of 10.6 μm. This excitation is the controllable heating beam, confirmed by a preliminary test on a wooden plate 1.2 m x 0.9 m x 1 cm. As the first practice, this method is applied to detecting the defect in CFRP heated by the Laser 300 W during 40 s. Two samples 40 cm x 40 cm x 4.5 cm are prepared, one with defect, another one without defect. The laser beam passes through the lens of a deviation device, and heats the samples placed at a determinate position and area. As a result, the absence of adhesive can be detected. This method displays prominently its application as NDT with the composite materials. This work gives a good perspective to characterize the laser beam, which is very useful for the next detection campaigns.
Abstract: In this paper, a fiber based Fabry-Perot interferometer
is proposed and demonstrated for a non-contact displacement
measurement. A piece of micro-prism which attached to the
mechanical vibrator is served as the target reflector. Interference
signal is generated from the superposition between the sensing beam
and the reference beam within the sensing arm of the fiber sensor.
This signal is then converted to the displacement value by using a
developed program written in visual Cµ programming with a
resolution of λ/8. A classical function generator is operated for
controlling the vibrator. By fixing an excitation frequency of 100 Hz
and varying the excitation amplitude range of 0.1 – 3 Volts, the
output displacements measured by the fiber sensor are obtained from
1.55 μm to 30.225 μm. A reference displacement sensor with a
sensitivity of ~0.4 μm is also employed for comparing the
displacement errors between both sensors. We found that over the
entire displacement range, a maximum and average measurement
error are obtained of 0.977% and 0.44% respectively.
Abstract: Accurate evaluation of damping ratios involving soilstructure interaction (SSI) effects is the prerequisite for seismic design of in-situ buildings. This study proposes a combined approach to identify damping ratios of SSI systems based on ambient excitation technique. The proposed approach is illustrated with main test process, sampling principle and algorithm steps through an engineering example, as along with its feasibility and validity. The proposed approach is employed for damping ratio identification of 82 buildings in Xi-an, China. Based on the experimental data, the variation range and tendency of damping ratios of these SSI systems, along with the preliminary influence factor, are shown and discussed. In addition, a fitting curve indicates the relation between the damping ratio and fundamental natural period of SSI system.
Abstract: For micro-gyroscopes, the angular rate detection components have to oscillate forwards and backwards alternatively. An innovative design of micro-electromagnetic drive module is proposed to make a Π-type disc reciprocally and efficiently rotate within a certain of angular interval. Twelve Electromagnetic poles enclosing the thin disc are designed to provide the magnetic drive power. Isotropic etching technique is employed to fabricate the high-aspect-ratio trench, so that the contact angle of wire against trench can be increased and the potential defect of cavities and pores within the wire can be prevented. On the other hand, a Π-type thin disc is designed to conduct the pitch motion as an angular excitation, in addition to spinning, is exerted on the gyroscope. The efficacy of the micro-magnetic drive module is verified by the commercial software, Ansoft Maxewll. In comparison with the conventional planar windings in micro-scale systems, the magnetic drive force is increased by 150%.
Abstract: In this paper we consider a nonlinear feedback control
called augmented automatic choosing control (AACC) using the
gradient optimization automatic choosing functions for nonlinear
systems. Constant terms which arise from sectionwise linearization
of a given nonlinear system are treated as coefficients of a stable
zero dynamics. Parameters included in the control are suboptimally
selected by expanding a stable region in the sense of Lyapunov
with the aid of the genetic algorithm. This approach is applied to
a field excitation control problem of power system to demonstrate
the splendidness of the AACC. Simulation results show that the new
controller can improve performance remarkably well.