Abstract: Modern applications realized onto FPGAs exhibit high connectivity demands. Throughout this paper we study the routing constraints of Virtex devices and we propose a systematic methodology for designing a novel general-purpose interconnection network targeting to reconfigurable architectures. This network consists of multiple segment wires and SB patterns, appropriately selected and assigned across the device. The goal of our proposed methodology is to maximize the hardware utilization of fabricated routing resources. The derived interconnection scheme is integrated on a Virtex style FPGA. This device is characterized both for its high-performance, as well as for its low-energy requirements. Due to this, the design criterion that guides our architecture selections was the minimal Energy×Delay Product (EDP). The methodology is fully-supported by three new software tools, which belong to MEANDER Design Framework. Using a typical set of MCNC benchmarks, extensive comparison study in terms of several critical parameters proves the effectiveness of the derived interconnection network. More specifically, we achieve average Energy×Delay Product reduction by 63%, performance increase by 26%, reduction in leakage power by 21%, reduction in total energy consumption by 11%, at the expense of increase of channel width by 20%.
Abstract: Thermal load calculations have been performed for
multi-layered walls that are composed of three different parts; a
common (sand and cement) plaster, and two types of locally
produced soft and hard bricks. The masonry construction of these
layered walls was based on concrete-backed stone masonry made of
limestone bricks joined by mortar. These multilayered walls are
forming the outer walls of the building envelope of a typical Libyan
house. Based on the periodic seasonal weather conditions, within the
Libyan cost region during summer and winter, measured thermal
conductivity values were used to implement such seasonal variation
of heat flow and the temperature variations through the walls. The
experimental measured thermal conductivity values were obtained
using the Hot Disk technique. The estimation of the thermal
resistance of the wall layers ( R-values) is based on measurements
and calculations. The numerical calculations were done using a
simplified analytical model that considers two different wall
constructions which are characteristics of such houses. According to
the obtained results, the R-values were quite low and therefore,
several suggestions have been proposed to improve the thermal
loading performance that will lead to a reasonable human comfort
and reduce energy consumption.
Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: Certain tRNA synthetases have developed highly accurate molecular machinery to discriminate their cognate amino acids. Those aaRSs achieve their goal via editing reaction in the Connective Polypeptide 1 (CP1). Recently mutagenesis studies have revealed the critical importance of residues in the CP1 domain for editing activity and X-ray structures have shown binding mode of noncognate amino acids in the editing domain. To pursue molecular mechanism for amino acid discrimination, molecular modeling studies were performed. Our results suggest that aaRS bind the noncognate amino acid more tightly than the cognate one. Finally, by comparing binding conformations of the amino acids in three systems, the amino acid binding mode was elucidated and a discrimination mechanism proposed. The results strongly reveal that the conserved threonines are responsible for amino acid discrimination. This is achieved through side chain interactions between T252 and T247/T248 as well as between those threonines and the incoming amino acids.
Abstract: This paper presents an approach for daily optimal operation of distribution networks considering Distributed Generators (DGs). Due to private ownership of DGs, a cost based compensation method is used to encourage DGs in active and reactive power generation. The objective function is summation of electrical energy generated by DGs and substation bus (main bus) in the next day. A genetic algorithm is used to solve the optimal operation problem. The approach is tested on an IEEE34 buses distribution feeder.
Abstract: In this study, a fuzzy-logic based control system was
designed to ensure that time and energy is saved during the operation
of load elevators which are used during the construction of tall
buildings. In the control system that was devised, for the load
elevators to work more efficiently, the energy interval where the
motor worked was taken as the output variable whereas the amount
of load and the building height were taken as input variables. The
most appropriate working intervals depending on the characteristics
of these variables were defined by the help of an expert. Fuzzy expert
system software was formed using Delphi programming language. In
this design, mamdani max-min inference mechanism was used and
the centroid method was employed in the clarification procedure. In
conclusion, it is observed that the system that was designed is
feasible and this is supported by statistical analyses..
Abstract: Hydrogen is an important chemical in many industries
and it is expected to become one of the major fuels for energy
generation in the future. Unfortunately, hydrogen does not exist in its
elemental form in nature and therefore has to be produced from
hydrocarbons, hydrogen-containing compounds or water.
Above its critical point (374.8oC and 22.1MPa), water has lower
density and viscosity, and a higher heat capacity than those of
ambient water. Mass transfer in supercritical water (SCW) is
enhanced due to its increased diffusivity and transport ability. The
reduced dielectric constant makes supercritical water a better solvent
for organic compounds and gases. Hence, due to the aforementioned
desirable properties, there is a growing interest toward studies
regarding the gasification of organic matter containing biomass or
model biomass solutions in supercritical water.
In this study, hydrogen and biofuel production by the catalytic
gasification of 2-Propanol in supercritical conditions of water was
investigated. Pt/Al2O3and Ni/Al2O3were the catalysts used in the
gasification reactions. All of the experiments were performed under a
constant pressure of 25MPa. The effects of five reaction temperatures
(400, 450, 500, 550 and 600°C) and five reaction times (10, 15, 20,
25 and 30 s) on the gasification yield and flammable component
content were investigated.
Abstract: Simultaneous transient conduction and radiation heat
transfer with heat generation is investigated. Analysis is carried out
for both steady and unsteady situations. two-dimensional gray
cylindrical enclosure with an absorbing, emitting, and isotropically
scattering medium is considered. Enclosure boundaries are assumed
at specified temperatures. The heat generation rate is considered
uniform and constant throughout the medium. The lattice Boltzmann
method (LBM) was used to solve the energy equation of a transient
conduction-radiation heat transfer problem. The control volume finite
element method (CVFEM) was used to compute the radiative
information. To study the compatibility of the LBM for the energy
equation and the CVFEM for the radiative transfer equation, transient
conduction and radiation heat transfer problems in 2-D cylindrical
geometries were considered. In order to establish the suitability of the
LBM, the energy equation of the present problem was also solved
using the the finite difference method (FDM) of the computational
fluid dynamics. The CVFEM used in the radiative heat transfer was
employed to compute the radiative information required for the
solution of the energy equation using the LBM or the FDM (of the
CFD). To study the compatibility and suitability of the LBM for the
solution of energy equation and the CVFEM for the radiative
information, results were analyzed for the effects of various
parameters such as the boundary emissivity. The results of the LBMCVFEM
combination were found to be in excellent agreement with
the FDM-CVFEM combination. The number of iterations and the
steady state temperature in both of the combinations were found
comparable. Results are found for situations with and without heat
generation. Heat generation is found to have significant bearing on
temperature distribution.
Abstract: In Iran, due to abundance of energy resources, energy consumption is extraordinarily higher than international standards and transportation sector is considered to be one of the major consumers of energy. Moreover, air pollution in urban areas as a result of high dependence on private vehicle and lower standards of vehicles, high subsidies spent on fuel and time waste due to traffic congestion in urban areas all have led to speculations on new strategies and policies in order to control energy consumption in transportation sector. These strategies and policies will be introduced in this paper and their consequences will be analyzed with consideration to socio-economic factors affecting the urban society of Iran. Besides, the intention is to suggest and analyze new approaches such as broader application of public transportation system, demand management in transport sector, replacement of deteriorated vehicles, quality improvement in car manufacture and introduction of substitute fuels.
Abstract: Recent progress in calculation of the one-loop selfenergy
of the electron bound in the Coulomb field is summarized.
The relativistic multipole expansion is introduced. This expansion
is based on a single assumption: except for the part of the time
component of the electron four-momentum corresponding to the
electron rest mass, the exchange of four-momentum between the
virtual electron and photon can be treated perturbatively. For non Sstates
and normalized difference n3En −E1 of the S-states this
itself yields very accurate results after taking the method to the third
order. For the ground state the perturbation treatment of the electron
virtual states with very high three-momentum is to be avoided. For
these states one can always rearrange the pertinent expression in such
a way that free-particle approximation is allowed. Combination of
the relativistic multipole expansion and free-particle approximation
yields very accurate result after taking the method to the ninth order.
These results are in very good agreement with the previous results
obtained by the partial wave expansion and definitely exclude the
possibility that the uncertainity in determination of the proton radius
comes from the uncertainity in the calculation of the one-loop selfenergy.
Abstract: This work deals with the initial applications and formulation of an anisotropic plastic-damage constitutive model proposed for non-linear analysis of reinforced concrete structures submitted to a loading with change of the sign. The original constitutive model is based on the fundamental hypothesis of energy equivalence between real and continuous medium following the concepts of the Continuum Damage Mechanics. The concrete is assumed as an initial elastic isotropic medium presenting anisotropy, permanent strains and bimodularity (distinct elastic responses whether traction or compression stress states prevail) induced by damage evolution. In order to take into account the bimodularity, two damage tensors governing the rigidity in tension or compression regimes are introduced. Then, some conditions are introduced in the original version of the model in order to simulate the damage unilateral effect. The three-dimensional version of the proposed model is analyzed in order to validate its formulation when compared to micromechanical theory. The one-dimensional version of the model is applied in the analyses of a reinforced concrete beam submitted to a loading with change of the sign. Despite the parametric identification problems, the initial applications show the good performance of the model.
Abstract: The scope of this paper is to describe a real electrical
installation of renewable energy using photovoltaic cells. The
displayed power grid connected network was established in 2007 at
area of Northern Greece. The photovoltaic park is composed of 6120
photovoltaic cells able to deliver a total power of 1.101.600 Wp. For
the transformation of DC voltage to AC voltage have been used 25
stand alone three phases inverters and for the connection at the
medium voltage network of Greek Power Authority have been
installed two oil immersed transformer of 630 kVA each one. Due to
the wide space area of installation a specific external lightning
protection system has been designed. Additionally, due to the
sensitive electronics of the control and protection systems of park,
surge protection, equipotent bonding and shielding were also of
major importance.
Abstract: Empirical force fields and density functional theory
(DFT) was used to study the binding energies and structures of
methylamine on the surface of activated carbons (ACs). This is a first
step in studying the adsorption of alkyl amines on the surface of
functionalized ACs. The force fields used were Dreiding (DFF),
Universal (UFF) and Compass (CFF) models. The generalized
gradient approximation with Perdew Wang 91 (PW91) functional
was used for DFT calculations. In addition to obtaining the aminecarboxylic
acid adsorption energies, the results were used to establish
reliability of the empirical models for these systems. CFF predicted a
binding energy of -9.227 (kcal/mol) which agreed with PW91 at -
13.17 (kcal/mol), compared to DFF 0 (kcal/mol) and UFF -0.72
(kcal/mol). However, the CFF binding energies for the amine to ester
and ketone disagreed with PW91 results. The structures obtained
from all models agreed with PW91 results.
Abstract: Hydrogen is regarded to play an important role in
future energy systems because it can be produced from abundant
resources and its combustion only generates water. The disposal of
waste tyres is a major problem in environmental management
throughout the world. The use of waste materials as a source of
hydrogen is particularly of interest in that it would also solve a waste
treatment problem. There is much interest in the use of alternative
feedstocks for the production of hydrogen since more than 95% of
current production is from fossil fuels. The pyrolysis of waste tyres
for the production of liquid fuels, activated carbons and gases has
been extensively researched. However, combining pyrolysis with
gasification is a novel process that can gasify the gaseous products
from pyrolysis. In this paper, an experimental investigation into the
production of hydrogen and other gases from the bench scale
pyrolysis-gasification of tyres has been investigated. Experiments
were carried using a two stage system consisting of pyrolysis of the
waste tyres followed by catalytic steam gasification of the evolved
gases and vapours in a second reactor. Experiments were conducted
at a pyrolysis temperature of 500 °C using Ni/Al2O3 as a catalyst. The
results showed that there was a dramatic increase in gas yield and the
potential H2 production when the gasification temperature was
increased from 600 to 900 oC. Overall, the process showed that high
yields of hydrogen can be produced from waste tyres.
Abstract: The present work deals with the calculation of
transport properties of Hg0.8Cd0.2Te (MCT) semiconductor in
degenerate case. Due to their energy-band structure, this material
becomes degenerate at moderate doping densities, which are around
1015 cm-3, so that the usual Maxwell-Boltzmann approximation is
inaccurate in the determination of transport parameters. This problem
is faced by using Fermi-Dirac (F-D) statistics, and the non-parabolic
behavior of the bands may be approximated by the Kane model. The
Monte Carlo (MC) simulation is used here to determinate transport
parameters: drift velocity, mean energy and drift mobility versus
electric field and the doped densities. The obtained results are in
good agreement with those extracted from literature.
Abstract: In this study, the use of silicon NAM (Non-Audible
Murmur) microphone in automatic speech recognition is presented.
NAM microphones are special acoustic sensors, which are attached
behind the talker-s ear and can capture not only normal (audible)
speech, but also very quietly uttered speech (non-audible murmur).
As a result, NAM microphones can be applied in automatic speech
recognition systems when privacy is desired in human-machine communication.
Moreover, NAM microphones show robustness against
noise and they might be used in special systems (speech recognition,
speech conversion etc.) for sound-impaired people. Using a small
amount of training data and adaptation approaches, 93.9% word
accuracy was achieved for a 20k Japanese vocabulary dictation
task. Non-audible murmur recognition in noisy environments is also
investigated. In this study, further analysis of the NAM speech has
been made using distance measures between hidden Markov model
(HMM) pairs. It has been shown the reduced spectral space of NAM
speech using a metric distance, however the location of the different
phonemes of NAM are similar to the location of the phonemes
of normal speech, and the NAM sounds are well discriminated.
Promising results in using nonlinear features are also introduced,
especially under noisy conditions.
Abstract: In cognitive radio (CR) systems, the primary user (PU) signal would randomly depart or arrive during the sensing period of a CR user, which is referred to as the high traffic environment. In this paper, we propose a novel spectrum sensing scheme based
on the cyclostationarity of PU signals in high traffic environments. Specifically, we obtain a test statistic by applying an estimate of spectral autocoherence function of the PU signal to the generalized- likelihood ratio. From numerical results, it is confirmed that the proposed scheme provides a better spectrum sensing performance compared with the conventional spectrum sensing scheme based on the energy of the PU signals in high traffic environments.
Abstract: State Dependent Riccati Equation (SDRE) approach is
a modification of the well studied LQR method. It has the capability of being applied to control nonlinear systems. In this paper the technique
has been applied to control the single inverted pendulum (SIP) which represents a rich class of nonlinear underactuated systems. SIP
modeling is based on Euler-Lagrange equations. A procedure is developed
for judicious selection of weighting parameters and constraint handling. The controller designed by SDRE technique here gives better results than existing controllers designed by energy based techniques.
Abstract: This paper describes dynamic analysis using proposed
fast finite element method for a shock absorbing structure including a
sponge. The structure is supported by nonlinear concentrated springs.
The restoring force of the spring has cubic nonlinearity and linear
hysteresis damping. To calculate damping properties for the structures
including elastic body and porous body, displacement vectors as
common unknown variable are solved under coupled condition. Under
small amplitude, we apply asymptotic method to complex eigenvalue
problem of this system to obtain modal parameters. And then
expressions of modal loss factor are derived approximately. This
approach was proposed by one of the authors previously. We call this
method as Modal Strain and Kinetic Energy Method (MSKE method).
Further, using the modal loss factors, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled equations using normal coordinate corresponding to linear
natural modes. This transformation yields computation efficiency. As
a numerical example of a shock absorbing structures, we adopt double
skins with a sponge. The double skins are supported by nonlinear
concentrated springs. We clarify influences of amplitude of the input
force on nonlinear and chaotic responses.
Abstract: Social, mobility and information aggregation inside
business environment need to converge to reach the next step of
collaboration to enhance interaction and innovation. The following
article is based on the “Assemblage" concept seen as a framework to
formalize new user interfaces and applications. The area of research
is the Energy Social Business Environment, especially the Energy
Smart Grids, which are considered as functional and technical
foundations of the revolution of the Energy Sector of tomorrow. The
assemblages are modelized by means of mereology and simplicial
complexes. Its objective is to offer new central attention and
decision-making tools to end-users.