Abstract: This paper presents one of the best applications of wireless sensor network for campus Monitoring. With the help of PIR sensor, temperature sensor and humidity sensor, effective utilization of energy resources has been implemented in one of rooms of Sharda University, Greater Noida, India. The RISC microcontroller is used here for analysis of output of sensors and providing proper control using ZigBee protocol. This wireless sensor module presents a tremendous power saving method for any campus
Abstract: Electric vehicles are considered as technology which
can significantly reduce the problems related to road transport such
as increasing GHG emissions, air pollutions and energy import
dependency.
The core objective of this paper is to analyze the current energetic,
ecological and economic characteristics of different types of electric
vehicles.
The major conclusions of this analysis are: The high investments
cost are the major barrier for broad market breakthrough of battery
electric vehicles and fuel cell vehicles. For battery electric vehicles
also the limited driving range states a key obstacle. The analyzed
hybrids could in principle serve as a bridging technology. However,
due to their tank-to-wheel emissions they cannot state a proper
solution for urban areas.
Finally, the most important perception is that also battery electric
vehicles and fuel cell vehicles are environmentally benign solution if
the primary fuel source is renewable.
Abstract: An improved topology of a voltage-fed quasi-resonant
soft switching LCrCdc series-parallel half bridge inverter with a constant-frequency for electronic ballast applications is proposed in this paper. This new topology introduces a low-cost solution to
reduce switching losses and circuit rating to achieve high-efficiency
ballast. Switching losses effect on ballast efficiency is discussed
through experimental point of view. In this discussion, an improved
topology in which accomplishes soft switching operation over a wide
power regulation range is proposed. The proposed structure uses reverse recovery diode to provide better operation for the ballast system. A symmetrical pulse wide modulation (PWM) control scheme is implemented to regulate a wide range of out-put power.
Simulation results are kindly verified with the experimental
measurements obtained by ballast-lamp laboratory prototype. Different load conditions are provided in order to clarify the
performance of the proposed converter.
Abstract: In this paper, growth and collapse of a vapour bubble
generated due to a local energy input inside a rigid cylinder and in
the absence of buoyancy forces is investigated using Boundary
Integral Equation Method and Finite Difference Method .The fluid is
treated as potential flow and Boundary Integral Equation Method is
used to solve Laplace-s equation for velocity potential. Different
ratios of the diameter of the rigid cylinder to the maximum radius of
the bubble are considered. Results show that during the collapse
phase of the bubble inside a vertical rigid cylinder, two liquid micro
jets are developed on the top and bottom sides of the vapour bubble
and are directed inward. It is found that by increasing the ratio of the
cylinder diameter to the maximum radius of the bubble, the rate of
the growth and collapse phases of the bubble increases and the life
time of the bubble decreases.
Abstract: Advancements in the field of artificial intelligence
(AI) made during this decade have forever changed the way we look
at automating spacecraft subsystems including the electrical power
system. AI have been used to solve complicated practical problems
in various areas and are becoming more and more popular nowadays.
In this paper, a mathematical modeling and MATLAB–SIMULINK
model for the different components of the spacecraft power system is
presented. Also, a control system, which includes either the Neural
Network Controller (NNC) or the Fuzzy Logic Controller (FLC) is
developed for achieving the coordination between the components of
spacecraft power system as well as control the energy flows. The
performance of the spacecraft power system is evaluated by
comparing two control systems using the NNC and the FLC.
Abstract: Emerging Bio-engineering fields such as Brain
Computer Interfaces, neuroprothesis devices and modeling and
simulation of neural networks have led to increased research activity
in algorithms for the detection, isolation and classification of Action
Potentials (AP) from noisy data trains. Current techniques in the field
of 'unsupervised no-prior knowledge' biosignal processing include
energy operators, wavelet detection and adaptive thresholding. These
tend to bias towards larger AP waveforms, AP may be missed due to
deviations in spike shape and frequency and correlated noise
spectrums can cause false detection. Also, such algorithms tend to
suffer from large computational expense.
A new signal detection technique based upon the ideas of phasespace
diagrams and trajectories is proposed based upon the use of a
delayed copy of the AP to highlight discontinuities relative to
background noise. This idea has been used to create algorithms that
are computationally inexpensive and address the above problems.
Distinct AP have been picked out and manually classified from
real physiological data recorded from a cockroach. To facilitate
testing of the new technique, an Auto Regressive Moving Average
(ARMA) noise model has been constructed bases upon background
noise of the recordings. Along with the AP classification means this
model enables generation of realistic neuronal data sets at arbitrary
signal to noise ratio (SNR).
Abstract: A two dimensional three segments coupled pendulum system that mathematically models human arm configuration was developed along with constructing and solving the equations of motions for this model using the energy (work) based approach of Lagrange. The equations of motion of the model were solved iteratively both as an initial value problem and as a two point boundary value problem. In the initial value problem solutions, both the initial system configuration (segment angles) and initial system velocity (segment angular velocities) were used as inputs, whereas, in the two point boundary value problem solutions initial and final configurations and time were used as inputs to solve for the trajectory of motion. The results suggest that the model solutions are sensitive to small changes in the dynamic forces applied to the system as well as to the initial and boundary conditions used. To overcome the system sensitivity a new approach is suggested.
Abstract: One of the key research issues in wireless sensor networks (WSNs) is how to efficiently deploy sensors to cover an area. In this paper, we present a Fishnet Based Dispatch Scheme (FiBDS) with energy aware mobility and interest based sensing angle. We propose two algorithms, one is FiBDS centralized algorithm and another is FiBDS distributed algorithm. The centralized algorithm is designed specifically for the non-time critical applications, commonly known as non real-time applications while the distributed algorithm is designed specifically for the time critical applications, commonly known as real-time applications. The proposed dispatch scheme works in a phase-selection manner. In this in each phase a specific constraint is dealt with according to the specified priority and then moved onto the next phase and at the end of each only the best suited nodes for the phase are chosen. Simulation results are presented to verify their effectiveness.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. Several cellular materials are widely used
as core of the sandwich structures and their properties influence
the response of the entire element under impact load. To optimize
their performance requires the characterisation of the core material
behaviour at high strain rates and identification of the underlying
mechanism. This work presents the study of high strain-rate
characteristics of a specific porous lightweight blast energy absorbing
foam using a Split Hopkinson Pressure Bar (SHPB) technique
adapted to perform tests on low strength materials. Two different
velocities, 15 and 30 m.s-1 were used to determine the strain
sensitivity of the material. Foams were designed using two types of
porous lightweight spherical raw materials with diameters of 30-
100 *m, combined with polymer matrix. Cylindrical specimens with
diameter of 15 mm and length of 7 mm were prepared and loaded
using a Split Hopkinson Pressure Bar apparatus to assess the relation
between the composition of the material and its shock wave
attenuation capacity.
Abstract: Solar Cells are destined to supply electric energy beginning from primary resources. It can charge a battery up to 12V dc. For residential use an inverter for 12V dc to 220Vac conversion is desired. For this a static DC-AC converter is necessarily inserted between the solar cells and the distribution network. This paper describes a new P.W.M. strategy for a voltage source inverter. This modulation strategy reduces the energy losses and harmonics in the P.W.M. voltage source inverter. This technique allows the P.W.M. voltage source inverter to become a new feasible solution for solar home application.
Abstract: Removal of PCP by a system combining
biodegradation by biofilm and adsorption was investigated here.
Three studies were conducted employing batch tests, sequencing
batch reactor (SBR) and continuous biofilm activated carbon
column reactor (BACCOR). The combination of biofilm-GAC
batch process removed about 30% more PCP than GAC adsorption
alone. For the SBR processes, both the suspended and attached
biomass could remove more than 90% of the PCP after
acclimatisation. BACCOR was able to remove more than 98% of
PCP-Na at concentrations ranging from 10 to 100 mg/L, at empty
bed contact time (EBCT) ranging from 0.75 to 4 hours. Pure and
mixed cultures from BACCOR were tested for use of PCP as sole
carbon and energy source under aerobic conditions. The isolates
were able to degrade up to 42% of PCP under aerobic conditions in
pure cultures. However, mixed cultures were found able to degrade
more than 99% PCP indicating interdependence of species.
Abstract: Environmental performance of the U.S. States is investigated for the period of 1990 – 2007 using Stochastic Frontier Analysis (SFA). The SFA accounts for both efficiency measure and stochastic noise affecting a frontier. The frontier is formed using indicators of GDP, energy consumption, population, and CO2 emissions. For comparability, all indicators are expressed as ratios to total. Statistical information of the Energy Information Agency of the United States is used. Obtained results reveal the bell - shaped dynamics of environmental efficiency scores. The average efficiency scores rise from 97.6% in 1990 to 99.6% in 1999, and then fall to 98.4% in 2007. The main factor is insufficient decrease in the rate of growth of CO2 emissions with regards to the growth of GDP, population and energy consumption. Data for 2008 following the research period allow for an assumption that the environmental performance of the U.S. States has improved in the last years.
Abstract: One of the main and responsible units of Sulzer
projectile loom is picking mechanism. It is specifically designed to
accelerate projectile to speed of 25 m / s. Initial speed projectile of
Sulzer projectile loom is independent of speed loom and determined
the potential energy torsion rod. This paper investigates the dynamics
picking mechanism of Sulzer projectile loom during its discharge. A
result of calculation model, we obtain the law of motion lever of
picking mechanism during its discharge. Construction of dynamic
model the picking mechanism of Sulzer projectile loom on software
complex SimulationX can make calculations for different thickness
of torsion rods taking into account the backlashes in the connections,
the dissipative forces and resistance forces
Abstract: Energy intensity(energy consumption intensity) is a
global index which computes the required energy for producing a
specific value of goods and services in each country. It is computed
in terms of initial energy supply or final energy consumption. In this
study (research) Divisia method is used to decompose energy
consumption and energy intensity. This method decomposes
consumption and energy intensity to production effects, structural
and net intensity and could be done as time series or two-periodical.
This study analytically investigates consumption changes and energy
intensity on economical sectors of Iran and more specific on road
transportation(rail road and road).Our results show that the
contribution of structural effect (change in economical activities
combination) is very low and the effect of net energy consumption
has the higher contribution in consumption changes and energy
intensity. In other words, the high consumption of energy is due to
Intensity of energy consumption and is not to structural effect of
transportation sector.
Abstract: The empirical mode decomposition (EMD) represents any time series into a finite set of basis functions. The bases are termed as intrinsic mode functions (IMFs) which are mutually orthogonal containing minimum amount of cross-information. The EMD successively extracts the IMFs with the highest local frequencies in a recursive way, which yields effectively a set low-pass filters based entirely on the properties exhibited by the data. In this paper, EMD is applied to explore the properties of the multi-year air temperature and to observe its effects on climate change under global warming. This method decomposes the original time-series into intrinsic time scale. It is capable of analyzing nonlinear, non-stationary climatic time series that cause problems to many linear statistical methods and their users. The analysis results show that the mode of EMD presents seasonal variability. The most of the IMFs have normal distribution and the energy density distribution of the IMFs satisfies Chi-square distribution. The IMFs are more effective in isolating physical processes of various time-scales and also statistically significant. The analysis results also show that the EMD method provides a good job to find many characteristics on inter annual climate. The results suggest that climate fluctuations of every single element such as temperature are the results of variations in the global atmospheric circulation.
Abstract: Sulphur dioxide is a harmful gaseous product that
needs to be minimized in the atmosphere. This research work
investigates the use of zeolite as a possible additive that can improve
the sulphur dioxide capture in wet flue gas desulphurisation
dissolution process. This work determines the effect of temperature,
solid to liquid ratio, acid concentration and stirring speed on the
leaching of zeolite using a pH stat apparatus. The atomic absorption
spectrometer was used to measure the calcium ions from the solution.
It was found that the dissolution rate of zeolite decreased with
increase in solid to liquid ratio and increases with increase in
temperature, stirring speed and acid concentration. The activation
energy for the dissolution rate of zeolite in hydrochloric acid was
found to be 9.29kJ/mol. and therefore the product layer diffusion was
the rate limiting step.
Abstract: In nature, electromagnetic fields always appear like
atmosphere static electric field, the earth's static magnetic field and
the wide-rang frequency electromagnetic field caused by lightening.
However, besides natural electromagnetic fields (EMF), today human
beings are mostly exposed to artificial electromagnetic fields due to
technology progress and outspread use of electrical devices. To
evaluate nuisance of EMF, it is necessary to know field intensity for
every frequency which appears and compare it with allowed values.
Low frequency EMF-s around transmission and distribution lines are
time-varying quasi-static electromagnetic fields which have
conservative component of low frequency electrical field caused by
charges and eddy component of low frequency magnetic field caused
by currents. Displacement current or field delay are negligible, so
energy flow in quasi-static EMF involves diffusion, analog like heat
transfer. Electrical and magnetic field can be analyzed separately.
This paper analysis the numerical calculations in ELF-400 software
of EMF in distribution substation in shopping center. Analyzing the
results it is possible to specify locations exposed to the fields and
give useful suggestion to eliminate electromagnetic effect or reduce it
on acceptable level within the non-ionizing radiation norms and
norms of protection from EMF.
Abstract: The tray/multi-tray distillation process is a topic that
has been investigated to great detail over the last decade by many
teams such as Jubran et al. [1], Adhikari et al. [2], Mowla et al. [3],
Shatat et al. [4] and Fath [5] to name a few. A significant amount of
work and effort was spent focusing on modeling and/simulation of
specific distillation hardware designs. In this work, we have focused
our efforts on investigating and gathering experimental data on
several engineering and design variables to quantify their influence
on the yield of the multi-tray distillation process. Our goals are to
generate experimental performance data to bridge some existing gaps
in the design, engineering, optimization and theoretical modeling
aspects of the multi-tray distillation process.
Abstract: Until recently, energy security and climate change
were considered separate issues to be dealt with by policymakers.
The two issues are now converging, challenging the security and
climate communities to develop a better understanding of how to deal
with both issues simultaneously. Although Egypt is not a major
contributor to the world's total GHG emissions, it is particularly
vulnerable to the potential effects of global climate change such as
rising sea levels and changed patterns of rainfall in the Nile Basin.
Climate change is a major threat to sustainable growth and
development in Egypt, and the achievement of the Millennium
Development Goals. Egypt-s capacity to respond to the challenges of
climate instability will be expanded by improving overall resilience,
integrating climate change goals into sustainable development
strategies, increasing the use of modern energy systems with reduced
carbon intensity, and strengthening international initiatives. This
study seeks to establish a framework for considering the complex and
evolving links between energy security and climate change,
applicable to Egypt.
Abstract: A co-generation system in automobile can improve
thermal efficiency of vehicle in some degree. The waste heat from the
engine exhaust and coolant is still attractive energy source that reaches
around 60% of the total energy converted from fuel. To maximize the
effectiveness of heat exchangers for recovering the waste heat, it is
vital to select the most suitable working fluid for the system, not to
mention that it is important to find the optimum design for the heat
exchangers. The design of heat exchanger is out of scoop of this study;
rather, the main focus has been on the right selection of working fluid
for the co-generation system. Simulation study was carried out to find
the most suitable working fluid that can allow the system to achieve
the optimum efficiency in terms of the heat recovery rate and thermal
efficiency.