Abstract: The study of interaction among the grain, moisture,
and the surrounding space (air) is key to understanding the graindrying
process. In Iran, rice (mostly Indica type) is dried by flat
bed type dryer until the final MC reaches to 6 to 8%. The
experiments were conducted to examine the effect of application of
discharge fan with different heights of paddy on the drying
efficiency. Experiments were designed based on two different
configurations of the drying methods; with and without discharge
fan with three different heights of paddy including; 5, 10, and 15
cm. The humid heated air will be going out immediately by the
suction of discharge fan. The drying time is established upon the
average final MC to achieve about 8%. To save energy and reduce
the drying time, the distribution of temperature between layers
should be fast and uniform with minimum difference; otherwise
the difference of MC gradient between layers will be high and will
induce grain breakage. The difference of final MC between layers
in the two methods was 48-73%. The steady state of temperature
between the two methods has saved time in the range of 10-20%,
and the efficiency of temperature distribution increased 17-26% by
the use of discharge fan.
Abstract: Thirty three re-wetting tests were conducted at
different combinations of temperatures (5.7- 46.30C) and relative
humidites (48.2-88.6%) with barley. Two most commonly used thinlayer
drying and rewetting models i.e. Page and Diffusion were
compared for their ability to the fit the experimental re-wetting data
based on the standard error of estimate (SEE) of the measured and
simulated moisture contents. The comparison shows both the Page
and Diffusion models fit the re-wetting experimental data of barley
well. The average SEE values for the Page and Diffusion models
were 0.176 % d.b. and 0.199 % d.b., respectively. The Page and
Diffusion models were found to be most suitable equations, to
describe the thin-layer re-wetting characteristics of barley over a
typically five day re-wetting. These two models can be used for the
simulation of deep-bed re-wetting of barley occurring during
ventilated storage and deep bed drying.
Abstract: Optimization of extraction of phenolic compounds
from Avicennia marina using response surface methodology was
carried out during the present study. Five levels, three factors
rotatable design (CCRD) was utilized to examine the optimum
combination of extraction variables based on the TPC of Avicennia
marina leaves. The best combination of response function was 78.41
°C, drying temperature; 26.18°C; extraction temperature and 36.53
minutes of extraction time. However, the procedure can be promptly
extended to the study of several others pharmaceutical processes like
purification of bioactive substances, drying of extracts and
development of the pharmaceutical dosage forms for the benefit of
consumers.
Abstract: Impinging jets are used in various industrial areas as a cooling and drying technique. The current research is concerned with the means of improving the heat transfer for configurations with a minimum distance of the nozzle to the impingement surface. The impingement heat transfer is described using numerical methods over a wide range of parameters for an array of planar jets. These parameters include varying jet flow speed, width of nozzle, distance of nozzle, angle of the jet flow, velocity and geometry of the impingement surface. Normal pressure and shear stress are computed as additional parameters. Using dimensionless characteristic numbers the parameters and the results are correlated to gain generalized equations. The results demonstrate the effect of the investigated parameters on the flow.
Abstract: The current practice of determination of moisture diffusivity of building materials under laboratory conditions is predominantly aimed at the absorption phase. The main reason is the simplicity of the inverse analysis of measured moisture profiles. However, the liquid moisture transport may exhibit significant hysteresis. Thus, the moisture diffusivity should be different in the absorption (wetting) and desorption (drying) phase. In order to bring computer simulations of hygrothermal performance of building materials closer to the reality, it is then necessary to find new methods for inverse analysis which could be used in the desorption phase as well. In this paper we present genetic algorithm as a possible method of solution of the inverse problem of moisture transport in desorption phase. Its application is demonstrated for AAC as a typical building material.
Abstract: This paper presents a design method of self-tuning
Quantitative Feedback Theory (QFT) by using improved deadbeat
control algorithm. QFT is a technique to achieve robust control with
pre-defined specifications whereas deadbeat is an algorithm that
could bring the output to steady state with minimum step size.
Nevertheless, usually there are large peaks in the deadbeat response.
By integrating QFT specifications into deadbeat algorithm, the large
peaks could be tolerated. On the other hand, emerging QFT with
adaptive element will produce a robust controller with wider
coverage of uncertainty. By combining QFT-based deadbeat
algorithm and adaptive element, superior controller that is called selftuning
QFT-based deadbeat controller could be achieved. The output
response that is fast, robust and adaptive is expected. Using a grain
dryer plant model as a pilot case-study, the performance of the
proposed method has been evaluated and analyzed. Grain drying
process is very complex with highly nonlinear behaviour, long delay,
affected by environmental changes and affected by disturbances.
Performance comparisons have been performed between the
proposed self-tuning QFT-based deadbeat, standard QFT and
standard dead-beat controllers. The efficiency of the self-tuning QFTbased
dead-beat controller has been proven from the tests results in
terms of controller’s parameters are updated online, less percentage
of overshoot and settling time especially when there are variations in
the plant.
Abstract: In this work Membrane Distillation is applied to
concentrate orange Juice. Clarified orange juice (11o Brix) obtained
from fresh fruits and a sugar solution was subjected to membrane
distillation. The experiments were performed on a flat sheet module
using orange juice and sucrose solution as feeds. The concentration
of a sucrose solution, used as a model fruit juice and also orange
juice, was carried out in a direct contact membrane distillation using
hydrophobic PTFE membrane of pore size 0.2 μm and porosity 70%.
Surface modification of PTFE membrane has been carried out by
treating membrane with alcohol and water solution to make it
hydrophilic and then hydrophobicity was regained by drying. The
influences of the feed temperature, feed concentration, flow rate,
operating time on the permeate flux were studied for treated and non
treated membrane. In this work treated and non treated membrane
were compared in terms of water flux, Within the tested range, MD
with surface modified membrane the water flux has been
significantly improved by treating the membrane surface.
Abstract: Majority of pepper farmers in Malaysia are using the
open-sun method for drying the pepper berries. This method is time
consuming and exposed the berries to rain and contamination. A
maintenance-friendly and properly enclosed dryer is therefore
desired. A dryer design with a solar collector and a chimney was
studied and adapted to suit the needs of small-scale pepper farmers in
Malaysia. The dryer will provide an environment with an optimum
operating temperature meant for drying pepper berries. The dryer
model was evaluated by using commercially available computational
fluid dynamic (CFD) software in order to understand the heat and
mass transfer inside the dryer. Natural convection was the only mode
of heat transportation considered in this study as in accordance to the
idea of having a simple and maintenance-friendly design. To
accommodate the effect of low buoyancy found in natural convection
driers, a biomass burner was integrated into the solar dryer design.
Abstract: This paper reviews the objectives, methods and results of previous studies on biodrying of solid waste in several countries. Biodrying of solid waste is a novel technology in developing countries such as in Malaysia where high moisture content in organic waste makes the segregation process for recycling purposes complicated and diminishes the calorific value for the use of fuel source. In addition, the high moisture content also encourages the breeding of vectors and disease-bearing animals. From the laboratory results, the average moisture content of organic waste, paper, plastics and metals are 58.17%, 37.93%, 29.79% and 1.03% respectively for UKM campus. Biodrying of solid waste is a simple method of waste treatment as well as a cost-efficient technology to dry the solid waste. The process depends on temperature monitoring and air flow control along with the natural biodegradable process of organic waste. This review shows that the biodrying of solid waste method has high potential in treatment and recycling of solid waste, be useful for biodrying study and implementation in Malaysia.
Abstract: In present work, drying characteristics of fresh papaya (Carica papaya L.) was studied to understand the dehydration process and its behavior. Drying experiments were carried out by a laboratory scaled microwave-vacuum oven. The parameters affecting drying characteristics including operating modes (continuous, pulsed), microwave power (400 and 800 W), and vacuum pressure (20, 30, and 40 cmHg) were investigated. For pulsed mode, two levels of power-off time (60 and 120 s) were used while the power-on time was fixed at 60 s and the vacuum pressure was fixed at 40 cmHg. For both operating modes, the effects of drying conditions on drying time, drying rate, and effective diffusivity were investigated. The results showed high microwave power, high vacuum, and pulsed mode of 60 s-on/60 s-off favored drying rate as shown by the shorten drying time and increased effective diffusivity. The drying characteristics were then described by Page-s model, which showed a good agreement with experimental data.
Abstract: In this study, a software has been developed to predict
the optimum conditions for drying of cotton based yarn bobbins in a
hot air dryer. For this purpose, firstly, a suitable drying model has
been specified using experimental drying behavior for different
values of drying parameters. Drying parameters in the experiments
were drying temperature, drying pressure, and volumetric flow rate of
drying air. After obtaining a suitable drying model, additional curve
fittings have been performed to obtain equations for drying time and
energy consumption taking into account the effects of drying
parameters. Then, a software has been developed using Visual Basic
programming language to predict the optimum drying conditions for
drying time and energy consumption.