Abstract: Mathematical models of drying are used for the purpose of understanding the drying process in order to determine important parameters for design and operation of the dryer. The jackfruit is a fruit with high consumption in the Northeast and perishability. It is necessary to apply techniques to improve their conservation for longer in order to diffuse it by regions with low consumption. This study aimed to analyze several mathematical models (Page, Lewis, and Midilli) to indicate one that best fits the conditions of convective drying process using performance indicators associated with each model: accuracy (Af) and noise factors (Bf), mean square error (RMSE) and standard error of prediction (% SEP). Jackfruit drying was carried out in convective type tray dryer at a temperature of 50°C for 9 hours. It is observed that the model Midili was more accurate with Af: 1.39, Bf: 1.33, RMSE: 0.01%, and SEP: 5.34. However, the use of the Model Midilli is not appropriate for purposes of control process due to need four tuning parameters. With the performance indicators used in this paper, the Page model showed similar results with only two parameters. It is concluded that the best correlation between the experimental and estimated data is given by the Page’s model.
Abstract: Mangabeira (Hancornia speciosa Gomes), a native plant in Brazil, is found growing spontaneously in various regions of the country. The high perishability of tropical fruits such as mangaba, causes it to be necessary to use technologies that promote conservation, aiming to increase the shelf life of this fruit and add value. The objective of this study was to compare the mangabas lyophilization curves behaviors with different sizes and maturation stages. The fruits were freeze-dried for a period of approximately 45 hours at lyophilizer Liotop brand, model L -108. It has been considered large the fruits between 38 and 58 mm diameter and small, between 23 and 28 mm diameter and the two states of maturation, intermediate and mature. Large size mangabas drying curves in both states of maturation were linear behavior at all process, while the kinetic drying curves related to small fruits, independent of maturation state, had a typical behavior of drying, with all the well-defined steps. With these results it was noted that the time of lyophilization was suitable for small mangabas, a fact that did not happen with the larger one. This may indicate that the large mangabas require a longer time to freeze until reaches the equilibrium level, as it happens with the small fruits, going to have constant moisture at the end of the process. For both types of fruit were analyzed water activity, acidity, protein, lipid, and vitamin C before and after the process.
Abstract: Study production of tempeh inoculums powder by freeze-drying comparison with dry at 50°C and the sun bask for developing efficient tempeh inoculums for tempeh producing. Rhizopus oligosporus in PDA slant cultures was incubated at 30oC for 3-5 days until spores and mycelium. Preparation spores suspension with sterilized water and then count the number of started spores. Fill spores suspension in Rice flour and soy flour, mixed with water (in the ratio 10: 7), which is steamed and sterilized at 121°C 15min. Incubated at room temperature for 4 days, count number of spores. Then take the progressive infection and full spore dough to dry at 50°C, sun bask, and lyophilize. Grind to powder. Then pack in plastic bags, stored at 5°C. To investigate quality of inoculums which use different methods, tempeh was fermented every 4 weeks for 24 weeks of the experiment. The result found that rice flour is not suitable to use as raw material in the production of powdered spores. Fungi can growth rarely. Less number of spores and requires more time than soy flour. For drying method, lyophilization is the least possible time. Samples from this method are very hard and very dark and harder to grind than other methods. Drying at 50°C takes longer time than lyophilization but can also set time use for drying. Character of the dry samples is hard solid and brown color, but can be grinded easier. The sun drying takes the longest time, can’t determine the exact time. When the spore powder was used to fermented tempeh immediately, product has similar characters as which use spores that was fresh prepared. The tempeh has normal quality. When spore powder stored at low temperature, tempeh from storage spore in weeks 4, 8 and 12 is still normal. Time spending in production was close to the production of fresh spores. After storage spores for 16 and 20 weeks, tempeh is still normal but growth and sporulation were take longer time than usual (about 6 hours). At 24 week storage, fungal growth is not good, made tempeh looks inferior to normal color, also smell and texture.
Abstract: The behavior of model piles embedded in a very high expansive soil was investigated, a specially manufactured saturation-drying tank was used to apply three cycles of wetting and drying to the expansive soil surrounding the model straight shaft and under reamed piles, the relative movement of the piles with respect to the soil surface was recorded with time, also the exerted uplift pressure of the piles due to soil swelling was recorded. The behavior of unloaded straight shaft and under reamed piles was investigated. Two design charts were presented for straight shaft and under reamed piles one for the required pile depth for zero upward movement due to soil swelling, while the other for the required pile depth to exert zero uplift pressure when the soil swells. Under reamed piles showed a decrease in upward movement of 20% to 30%, and an uplift pressure decrease of 10% to 30%.
Abstract: The object of the present research was to assess the effects of partial rootzone drying (PRD) on tomato growth, productivity, biomass allocation and water use efficiency (WUE). Plants were grown under greenhouse, on a sand substrate. Three treatments were applied: a control that was fully and conventionally irrigated, PRD-70 and PRD-50 in which, respectively, 70% and 50% of water requirements were supplied using PRD. Alternation of irrigation between the two root halves took place each three days. The Control produces the highest total yield (252tons/ha). In terms of fruit number, PRD-50 showed 23% and 16% less fruits than PRD-70 and control, respectively. Fruit size was affected by treatment with PRD-50 treatment producing 66% and 53% more class 3 fruits than, control and PRD-70, respectively. For plant growth, the difference was not significant when comparing control to PRD-70 but was significant when comparing PRD-70 and control to PRD-50. No effect was on total biomass but root biomass was higher for stressed plants compared to control. WUE was 66% and 27% higher for PRD-50 and PRD-70 respectively compared to control.
Abstract: The study of the effect of the processing parameters on the level of intercalation between the layered silicate and polymer of two different methodology took place. X-ray diffraction, Scanning Electron Microscopy, Energy Dispersive X-ray Spectrometry, and Transmission Electron Microscopy were utilized in order to examine the intercalation level of nanocomposites of both methodologies. It was found that drying the clay prior to mixing with the polymer, mixing time and speed, degassing time, and the curing method had major changes to the level of distribution of the nanocomposites structure. In methodology 1, the presence of aggregation layers was observed at only 2.5 wt.% clay loading whereas in methodology 2 the presence of aggregation layers was found at higher clay loading (i.e. 5 wt.%).
Abstract: Organic farming systems still depend on intensive, mechanical soil tillage. Frequent passes by machinery traffic cause substantial soil compaction that threatens soil health. Adopting practices as reduced tillage and organic matter retention on the soil surface are considered effective ways to control soil compaction. In tropical regions, however, the acceleration of soil organic matter decomposition and soil carbon turnover on the topsoil layer is influenced more rapidly by the oscillation process of drying and wetting. It is hypothesized therefore, that rapid reduction in soil organic matter hastens the potential for compaction to occur in organic farming systems. Compaction changes soil physical properties and as a consequence it has been implicated as a causal agent in the inhibition of natural disease suppression in soils. Here we describe relationships between soil management in organic vegetable systems, soil compaction, and declining soil capacity to suppress pathogenic microorganisms.
Abstract: The purpose of present work was to study the drying kinetics of whole acorn and its kernel at different drying air temperatures and their effective moisture diffusivity. The results indicated that the drying time of whole acorn was 442, 206 and 188 min at the air temperature of 65, 75 and 85ºC, respectively. At the same temperatures, the drying time of kernel was 131, 56 and 76min. The results showed that the effect of drying air temperature increasing on the drying time reduction could not be significant on acorn drying at all conditions. The effective moisture diffusivity of whole acorn and kernel increased with increasing air temperature from 65 to 75ºC. However more air temperature increasing, led to decreasing this property of acorn kernel. The critical temperature of acorn drying was about 75°C in which acorn kernel had the highest effective moisture diffusivity.
Abstract: The heat and mass transfer was investigated during the falling rate period of spray drying of a slurry droplet. The effect of the porosity of crust layer formed from primary particles during liquid evaporation was studied numerically using the developed mathematical model which takes into account the heat and mass transfer in the core and crust regions, the movement of the evaporation interface, and the external heat and mass transfer between the drying air and the droplet surface. It was confirmed that the heat transfer through the crust layer was more intense in the case of the dense droplet than the loose one due to the enhanced thermal conduction resulting in the higher average droplet temperature. The mass transfer was facilitated in the crust layer of loose droplet owing to the large pore space available for diffusion of water vapor from the evaporation interface to the outer droplet surface. The longer drying time is required for the droplet of high porosity to reach the final moisture content than that for the dense one due to the larger amount of water to be evaporated during the falling rate.
Abstract: the research was accomplished on fresh in Latvia wild
growing cranberries and cranberry cultivars. The aim of the study
was to evaluate effect of pretreatment method and drying conditions
on the volatile compounds composition in cranberries. Berries
pre-treatment methods were: perforation, halving and
steam-blanching. The berries before drying in a cabinet drier were
pre-treated using all three methods, in microwave vacuum
drier – using a steam-blanching and halving. Volatile compounds in
cranberries were analysed using GC-MS of extracts obtained by
SPME. During present research 21 various volatile compounds were
detected in fresh cranberries: the cultivar 'Steven' - 15, 'Bergman'
and 'Early black' – 13, 'Ben Lear' and 'Pilgrim' – 11 and wild
cranberries – 14 volatile compounds. In dried cranberries 20 volatile
compounds were detected. Mathematical data processing allows
drawing a conclusion that there exists the significant influence of
cranberry cultivar, pre-treatment method and drying condition on
volatile compounds in berries and new volatile compound formation.
Abstract: Ascorbic acid (AA), commonly known as vitamin C, is essential for normal functioning of the body and maintenance of metabolic integrity. Among its various roles are as an antioxidant, a cofactor in collagen formation and other reactions, as well as reducing physical stress and maintenance of the immune system. Recent collaborative research between the Australian Defence Science and Technology Organisation (DSTO) in Scottsdale, Tasmania and RMIT University has sought to overcome the problems arising from the inherent instability of ascorbic acid during processing and storage of foods. The recent work has demonstrated the potential of microencapsulation by spray drying as a means to enhance retention. The purpose of this current study has been focused upon the influence of spray drying conditions on the properties of encapsulated ascorbic acid. The process was carried out according to a central composite design. Independent variables were: inlet temperature (80-120° C) and feed flow rate (7-14 mL/minute). Process yield, ascorbic acid loss, moisture content, water activity and particle size distribution were analysed as responses. The results have demonstrated the potential of microencapsulation by spray drying as a means to enhance retention. Vitamin retention, moisture content, water activity and process yield were influenced positively by inlet air temperature and negatively by feed flow rate.
Abstract: The optimal extraction condition of dried
Echinocactus grusonii powder was studied. The three independent
variables are raw material drying temperature, extraction
temperature, and extraction time. The dependent variables are both
yield percentage of crude extract and total phenolic quantification as
gallic acid equivalent in crude extract. The experimental design was
based on central composite design. Highest yield percentage of crude
extract could get from extraction condition at raw material drying
temperature at 60°C, extraction temperature at 15°C, and extraction
time for 25 min °C. Moreover, the crude extract with highest phenolic
occurred by extraction condition of raw material drying temperature
at 60°C, extraction temperature at 35 °C, and extraction lasting 25
min.
Abstract: This paper presents the prediction of air flow,
humidity and temperature patterns in a co-current pilot plant spray
dryer fitted with a pressure nozzle using a three dimensional model.
The modelling was done with a Computational Fluid Dynamic
package (Fluent 6.3), in which the gas phase is modelled as
continuum using the Euler approach and the droplet/ particle phase is
modelled by the Discrete Phase model (Lagrange approach).Good
agreement was obtained with published experimental data where the
CFD simulation correctly predicts a fast downward central flowing
core and slow recirculation zones near the walls. In this work, the
effects of the air flow pattern on droplets trajectories, residence time
distribution of droplets and deposition of the droplets on the wall also
were investigated where atomizing of maltodextrin solution was
used.
Abstract: In the course of the present work, plain (nonencapsulated)
and microencapsulated polyphenols were produced
using olive mill wastewater (OMW) as raw material, in order to be
used for enrichment of yogurt and dairy products. The OMW was
first clarified by using membrane technology and subsequently the
contained poly-phenols were isolated by adsorption-desorption
technique using selective macro-porous resins and finally recovered
in dry form after been processed by RO membrane technique
followed by freeze drying. Moreover, the polyphenols were
encapsulated in modified starch by freeze drying in order to mask the
color and bitterness effect and improve their functionality. The two
products were used successfully as additives in yogurt preparations
and the produced products were acceptable by the consumers and
presented with certain advantage to the plain yogurt. For the herein
proposed production scheme a patent application was already
submitted.
Abstract: Fruit drying is a well known process mostly used for
preservation of fruits. Osmotic dehydration of apricot slices were
carried out in three different salt-sucrose concentrations and four
different temperatures. Also three different weight ratios of solution
to sample were conducted to one set of experiments. The dehydration
curves were constructed using Peleg-s model. Increasing the solution
volume increased the mass transfer rate and hence the solid gain
increased rapidly. Increasing the volume of osmotic media caused an
increase in overall mass transfer but a 'solution to sample' ratio of 5:1
gave the best product quality. The best temperature and concentration
that had a high water loss to solid gain ratio and an acceptable taste
were 40°C and 5%, respectively.
Abstract: Pre-germinated parboiled brown rice or Khao hang (in Thai) is paddy which undergoing the processes of soaking, steaming, drying and dehusking to obtain the edible form for consumption. The objectives of this research were to study the kinetic of pre-germinated parboiled brown rice drying using fluidization technique and to study the properties of pre-germinated parboiled brown rice after drying. The dryings were performed at the different temperatures of 110, 120 and 130 oC at the bed depth of 2 cm with the air velocity of 1.98 m/s. The results found that the higher drying temperature led to the faster moisture reduction. After drying until the moisture content of pre-germinated parboiled brown rice was lower than 14%wet basis, samples were taken to determine various qualities such as percentage of head rice and L* a* b* color values. The shade drying was used as a control. The results found that the higher drying temperature resulted in the decrease of head rice percentage. For the color assessment, the trend of L* and a* values was increased with the drying temperature, while the b* value was not significantly difference (p › 0.05) by drying temperatures. However, the b value of drying by fluidized bed dryer was higher than the control.
Abstract: The aim of the study was to determine how different
ripening processes (traditional vs. industrial) influenced the
proteolysis in traditional Serbian dry-fermented sausage Petrovská
klobása. The obtained results indicated more intensive pH decline
(0.7 units after 9 days) in industrially ripened products (I), what had a
positive impact on drying process and proteolytic changes in these
samples. Thus, moisture content in I sausages was lower at each
sampling time, amounting 24.7% at the end of production period
(90 days). Likewise, the process of proteolysis was more pronounced
in I samples, resulting in higher contents of non-protein nitrogen
(NPN) and free amino acids nitrogen (FAAN), as well as in faster
and more intensive degradation of myosin (≈220 kDa), actin (≈45
kDa) and other polypeptides during processing. Consequently, the
appearance and accumulation of several protein fragments were
registered.
Abstract: A process flowsheet was developed in ChemCad 6.4
to study the effect of feed moisture contents on the pre-esterification
of waste oils. Waste oils were modelled as a mixture of triolein
(90%), oleic acid (5%) and water (5%). The process mainly consisted
of feed drying, pre-esterification reaction and methanol recovery. The
results showed that the process energy requirements would be
minimized when higher degrees of feed drying and higher preesterification
reaction temperatures are used.
Abstract: With the aim of improving nutritional profile and antioxidant capacity of gluten-free cookies, blueberry pomace, by-product of juice production, was processed into a new food ingredient by drying and grinding and used for a gluten-free cookie formulation. Since the quality of a baked product is highly influenced by the baking conditions, the objective of this work was to optimize the baking time and thickness of dough pieces, by applying Response Surface Methodology (RSM) in order to obtain the best technological quality of the cookies. The experiments were carried out according to a Central Composite Design (CCD) by selecting the dough thickness and baking time as independent variables, while hardness, color parameters (L*, a* and b* values), water activity, diameter and short/long ratio were response variables. According to the results of RSM analysis, the baking time of 13.74min and dough thickness of 4.08mm was found to be the optimal for the baking temperature of 170°C. As similar optimal parameters were obtained by previously conducted experiment based on sensory analysis, response surface methodology (RSM) can be considered as a suitable approach to optimize the baking process.
Abstract: Dill (Anethum graveolens L.) is a popular herb used in
many regions, including Baltic countries. Dill is widely used for
flavoring foods and beverages due to its pleasant spicy aroma. The
aim of this work was to determine the best blanching method for
processing of dill prior to microwave vacuum drying based on
sensory properties, color and volatile compounds in dried product.
Two blanching mediums were used – water and steam, and for part of
samples microwave pretreatment was additionally used. Evaluation of
dried dill volatile aroma compounds, color changes and sensory
attributes was performed. Results showed that blanching significantly
influences the quality of dried dill. After evaluation of volatile aroma
compounds, color and sensory properties of microwave vacuum dried
dill, as the best method for dill pretreatment was established
blanching at 90 °C for 30 s.